Search Documents

By W. Chae

The influence of solution ionic strength (IS) and electrolyte valence on the flotation behavior of malachite has been investigated. The microflotation tests were conducted over a range of solution IS (1?300 mM) at a constant speed (340 rpm), pH (9.5), flotation time (10 min), and sodium oleate dosage (5.3×10-7 moles/g). The size of malachite ranged from 45 to 53 µm, and two different types of electrolytes (NaCl and CaCl2) were employed. Electrophoretic mobility was also measured over the same IS range employed in the microflotation study. Overall, strong coupled effect of solution IS and ion valence was observed. Specifically, the flotability of malachite increased with increasing IS in the presence of monovalent cation (Na+) while the flotability increased up to 30 mM and decreased with increasing IS in the presence of divalent cation (Ca2+). Notably, the flotability of malachite was greater with the presence of Na+ compared with Ca2+ under high IS conditions (IS>30 mM). Consistent trend for Na+ versus Ca2+ was observed from the flotation results with different SO dosages. The characterization and flotation results suggested that the trend was likely attributed to the increased unfavorable interaction between malachite and bubble via the charge reversal of bubbles and malachite at higher IS in the presence of Ca2+.

Feb 27, 2013

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

By Keith A. Heasley, Jian Yang

"LaModel uses a laminated overburden boundary-element model and can calculate not only seam-level stresses and displacements but also surface subsidence for thin tabular deposit such as coal seams (Heasley, 1998). Up to this point in time, the material property wizards in LaModel have primarily been designed for calculating accurate stress distributions in single- and multipleseam situations, and for investigating and optimizing pillar sizes and layouts in relation to overburden, abutment, and multipleseam stresses. However, the critical input parameters that will give the most accurate seam-level stress distribution do not necessarily produce the best surface subsidence prediction. The objective of this paper is to develop a methodology for calibrating the critical input parameters in LaModel to optimize surface subsidence prediction.For optimum surface subsidence prediction, it was found that the gob convergence (as defined by the final gob modulus) and the overburden stiffness (as defined by the lamination thickness) were the two most critical parameters that needed to be calibrated (Heasley, 2016). By calibrating numerous panels with various widths and depths, a formula that provides the optimum final gob modulus to use for subsidence prediction was developed. Also, three different empirical formulas for optimizing the lamination thickness as a function of overburden depth and/or the panel width to- depth ratio were determined for the three cases: supercritical panels, and subcritical panels with and without offsets. Further, if the user has measured data for subsidence factor and angle-of draw, the optimum final gob modulus and lamination thickness can be determined from the measured data. These new subsidence prediction formulas are being implemented into new material wizards in LaModel.INTRODUCTIONIn the past few decades, with the increased need for highly productive mining techniques, full extraction mining methods have been increasingly employed in the U.S. coal mining industry. These total extraction mining methods, which include both longwall mining and room-and-pillar retreat mining, normally cause immediate roof caving and the associated surface subsidence. These methods can be highly productive and cost-effective, but the associated surface subsidence can cause damage to surface structures and negatively impact the surface environment (Peng, 2008). Therefore, a reliable program for predicting the surface subsidence associated with full extraction mining is required for appropriately engineering and managing the surface subsidence impacts of full extraction mining."

Jan 1, 2016

By Robert Cluff

The Campo Morado precious-metal-bearing, volcanogenic massive sulphide district occurs in a Lower Cretaceous felsic volcanic sequence in a northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. The deposits belong to a low-sulfidation, volcanogenic massive sulphide system formed in a subaqueous environment, and are of the siliciclastic type. Most are on the flanks of felsic domes or in adjacent basins and many are associated with heterolithic volcaniclastic rocks. The Reforma and possibly the El Rey massive sulphide deposits are interpreted to be overturned, and the Naranjo, El Largo, and Estrella de Oro deposits and the El Profundo occurrence to the south are upright. The G9 deposit and the La Lucha and San Rafael occurrences are in an over-thrust plate further to the southwest. In several of the deposits, zinc, lead, silver, and gold are concentrated near the stratigraphic top, and copper is concentrated near the stratigraphic base; copper also is concentrated in replacement bodies near the top of some domes. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Gold and silver occur in argentian gold, and silver also occurs in tennantite/freibergite and galena. Underlying stockwork zones contain disseminated and vein quartz, pyrite, chlorite, and ankerite, with locally abundant chalcopyrite and/or sphalerite. Exploration since 2004 has enlarged greatly the El Largo and the high-grade G-9 deposits, and slightly enlarged the El Rey deposit. The cumulative in situ massive sulphides for the Reforma, Naranjo, El Rey, El Largo, and G9 deposits exceed 45 Mt.

May 1, 2006

This is the third in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C. F. R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The second report gave the same data for motor gasolines sold during the summer of 1936)4/ As was the case with the first cooperative gasoline survey, reports were received for some areas from only one company and in other areas from two companies that did not in all instances report on the same brands of gasoline. In still other areas reports were received from five or six companies on the same brands of gasoline. Thus, it can be seen that data on gasolines are unequal in regard, to the number of reports that were averaged in calculating the data shown in table 1. The data from the Pacific Coast were averaged by the Pacific Coast technical group before submission and are published exactly as they were submitted.

Jan 1, 1937

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors&apos; point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1951

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By Stephen Chung, Graham Mustoe, Joe Haid

In an open cast coal mining operation, a 305 m (1000 ft) long by 49 m (160 ft) thick overburden cast blast can produce more than a million cubic yards of broken muck that needs to be removed before the coal recovery process can start. In the Powder River Basin of Wyoming, it is common to see 30 to 40 percent of the overburden cast to a spoil that does not require rehandling with heavy equipment. Therefore, the higher the percent cast, the better the cast blast is rated. However, depending on the shape of the muck profile, there is often 20 to 30 percent of the muck standing in front of the high-wall. This portion of muck would require a number of dozers to push down to the dragline pad level. From the mine operator point of view, it is believed that for a given muck profile, there should be an efficient dozer pushing method such that a dragline pad can be developed in the shortest time. As a tool for analyzing this dynamic problem, a 2-D discrete element model, i-PushTM, has been developed to simulate a dozer pushing operation. This mechanistic model takes into account the dozer blade geometry, the dozer operating procedure (e.g. cut-depth, blade fill distance, forward and reverse speeds at specific slope angles), material density and cohesion. To demonstrate how i-PushTM can be used to help determine the most productive push routine, this paper presents three dozer push methods to compare the effectiveness of pushing at 3:1, 4:1 and 5:1 push angles.

Jan 1, 2006

By H. Pei

PZH (Pan Zhi Hua) Iron and Steel (Group) Corporation, the biggest steel company in southwest China, has been using titanium-vanadium-magnetite as the main raw materials for blast furnace iron making processing for over 30 years. One of the problems that has a negative affect on the blast furnace operation is slag foaming. Based on the chemical components of the blast furnace slag-bearing higher TiO2, the foaming properties were studied. The TiO2content, which is calculated according to the total titanium content in all the forms of titanium compound in the slag, in this research is 30% weight per cent. Different forms of titanium compounds have different actions on the slag foaming behaviour that depends on the reduction condition in the blast furnace. The relationships among slag foaming performance and the binary alkalinity of the slag, the content of CaF2, MnO in slag, and the amount of gas injected in slag are investigated. The results show CaF2 and MnO have a stronger anti-foaming affect on the slag, even in the lower percentage. The way to measure high TiO2slag foaming performance and how to eliminate foamy slag are also discussed. Keywords: blast furnace slag bearing TiO2, foamy slag, foaming performance

Jan 1, 2004

By Francis W. Gray

Introduction Extensive undersea coal-mining has developed on both the east and west coasts of Canada, and at this time some four million tons, or 25 per cent of the total output of Canadian coal, representing a pit-mouth value of $14,000,000 per annum, is coming from coal seams lying under the sea. Of the coal now being mined in Nova Scotia, 55 per cent comes from under the sea, and this proportion is likely to increase. The Province of Nova Scotia is at this date receiving in royalties paid upon coal ?removed from undersea areas a sum exceeding $400,000 per annum. The subject is, therefore, one of special interest to the Mining Society of Nova Scotia and the Canadian Institute of Mining & Metallurgy, and while this paper will deal chiefly with undersea coal-mining in Nova Scotia, an attempt has been made to summarize the development of mining practice in the winning of undersea coal in other parts of the world, with the hope that such a recital may assist in the assessment of local problems. The connection between the mining of coal under the sea and an insular or maritime geography is obvious in regard to Great Britain, Japan, Vancouver Island, Australia, and Cape Breton Island, and also in regard to the curious conformation of Chile; the tendency towards growth of a mercantile marine and naval eminence is equally obvious where coal is mined at tidewater. But, there is the further and less favourable significance that the mining of coal under the sea is associated with poverty rather than with abundance of coal reserves.

Jan 1, 1927

By R. K. Singhal, H. Sahay

Introduction In terms of the world&apos;s recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world&apos;s total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada&apos;s total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

The market for titanium feedstocks (ilmenite, rutile,synthetic rutile and slag) is driven primarily by offtake from the titanium dioxide (TiO2) pigment industry. The pigment sector depends on the performance of the global economy. Titanium sponge is the first stage of titanium metal manufacture. It constitutes a minor component (3 percent) of overall demand for titanium feed-stocks. Production and consumption TiO2 pigment consumption in 2004 was estimated to be 4.63 Mt (5.1 million st), up 7.6 percent from 2003. It was driven by strong demand in most regions. In the United States, apparent TiO2 pigment consumption rebounded by 5.4 percent (highest growth rate since 1997) to an estimated 1.12 Mt (1.23 million st), following the decrease in demand during 2003. Chinese TiO2 pigment consumption continued its strong upward trend, increasing by 10 percent to 598 kt (659,000 st) in 2004.

Jan 1, 2005

By D. P. Penswick

The Palabora open pit is scheduled to cease operations in 2002. While the ore body continues below the bottom of the final pit shell, the stripping ratio precludes further economic open pit mining. Palabora Mining Company has investigated various means of continuing copper production, and has determined that an underground mine is the best solution. Board approval to commence construction of the mine has been granted and shaft sinking is underway. First production is planned for the year 2000 and full production of 30 000 t/d will be achieved by the end of the year 2002. [ ] Mechanised block caving will be the mining method employed at Palabora. The cave will be initiated by excavating a thin horizontal slice known as the undercut. Removal of the undercut will induce stresses which cause the rockmass overhead to fracture. Fractured rock will gravitate through drawbells to drawpoints on the production level, and be loaded by LHDs for transport to crushers.

Jan 1, 1997