Search Documents

By N. A. C. Smith, E. W. Dean, W. A. Jacobs, H. H. Hill

Fractional distillation is the most important process in the commercial refining of petroleum. The same procedure, conducted on a small scale, is the basis of a number of analytical methods of wide application in the petroleum laboratory. The Bureau of Mines has studied apparatus and procedure for the distillation analysis of petroleum, and this report is presented as a record of developments up to the present time. The work is incomplete, but the extensive information that has been obtained to date is made available as a guide in handling laboratory distillation problems. The analytical distillation of petroleum is commonly made to determine range of boiling points or to separate the oil. into fractions for detailed examination, or both. When only one of these two ends is sought the procedure involved is notably simpler than when, as is more common, information is required regarding both boiling range and properties of fractions. Moreover the degree of minuteness of measurement and the accuracy of the data required from analytical distillations differ considerably. Often the simplest sort of comparative figures are satisfactory; other tests require complicated and highly tedious procedure. No one distillation method is universally applicable, and it is impossible for anyone group of investigators to foresee all the different kinds of requirements that may occur in the industry.

Jan 1, 1922

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By Karim El-Ouassiti, Marc Minville, Stéphane Chabot, Claude Bazin, Valérie Ouellet

"Alumina is the main source of aluminium and it is extracted almost exclusively from bauxite ores found in the Southern hemisphere. Clays are abundant minerals that contain from 15 to 40% w/w of alumina from which it can be extracted by various processes. This paper reviews the processes used for the extraction of alumina from clays and discusses results obtained with a clay sample from the Murdochville area in the Quebec Province. The application of a conventional process to this clay did not yield an acceptable recovery although smelter grade alumina was produced. A modification to the process allows increasing alumina recovery from 85% to more than 92%. The application of the improved flow sheet to other alumina carriers failed to yield comparable recovery, showing that an optimum processing path for the recovery of alumina should be found for individual clay materials.INTRODUCTIONMost of the aluminium smelters are fed with alumina extracted from bauxite found in the Southern hemisphere. Bauxite is processed by the Bayer process that uses a caustic leach of the ore. In the middle of the century, the US Bureau of mines, motivated by the fear of an alumina delivery disruption, conducted several research projects aiming at producing alumina from non bauxitic ores. These projects led to the development of various acid leaching processes (Habashi, 1993). The sulphuric and hydrochloric acid leaching processes were brought to pilot plant evaluation (Bengtson, 1979), while nitric and other leach liquors were tested in the laboratory (Phillips and Wills, 1982; Habashi, 1983). Although clays are abundant and inexpensive minerals, the studied processes remained uncompetitive with the alumina extraction from bauxite (Hudson, 1987 page 42; Peters et al., 1962) for which reserves are estimated to support alumina production for the next 50 years (Oye et al., 1999). On the other hand, the local extraction of alumina from clays could significantly reduce the transportation costs of alumina to smelters and provide an alternative source of alumina supply from the Southern hemisphere countries. Also, the extraction of secondary products for some types of clay (Nasyrov et al., 1999) containing significant amounts of potassium and sodium could provide an additional return that may improve the economics of alumina production from clays."

Jan 1, 2005

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By T. S. Lundy, J. I. Federer

Chemically purified Zr95and Cb95 have been used in determining self-diffusion coefficients in the bcc phase of iodide zirconium over the temperature range of 900o to 1750°C. The temperature dependence of the diffusion coefficients could not be described by the usual Arrhenius-type equation over the entire temperature range. Values of the apparent frequency factors (D0)a and activation energies (Q)A for ZR95 varied from 4.8 x 10-6 to 2.5 x 10-2 sq cm per sec and 20,700 to 46,900 cal per mole, respectively, between 900°and 1750°C. Similarly, for Cb95, values of (Do) a and (Q)A varied from about 2.4 x 10'5 to 0.25 sq cm per sec and 26,500 to 56,800 cal per mole, respectively. The data may be described in terms of the a to ß transition temperature of 1136 °K and the absolute temperature of the diffusion anneals by the following eauations: SEVERAL studies on the diffusion of Zr95 in zirconium have been reported.1"5 The values of the constants contained in the usual Arrhenius-type equation for describing the temperature dependence of the diffusion coefficient, D = Do exp [- Q/(RT)], are summarized in Table I. The reported values of Do, the frequency factor, and Q, the activation energy, are seen to vary by factors of about 60 and 1.6, respectively. Examination of the data from any one study indicated reasonable consistency of measurements. The large discrepancies of over-all results, therefore, cannot be explained on the basis of experimental scatter. One possible explanation for the differences in results could be a varying impurity content of the zirconium. Another possibility is that the radioactive daughter, Cb95, influenced the values of some of the determined diffusion coefficients. Therefore, the first of the three purposes of this study was to reconcile the large differences in diffusion results that have been obtained. Several empirical relations have been proposed to relate the diffusion coefficients in solids with physical properties, such as the absolute melting point, the heat of fusion, and the heat of sublimation.

Jan 1, 1963

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By M. J. Ferrante

Laboratory-scale tests were undertaken to examine several electrolytes for possible use in separating nickel and cobalt from products being prepared at Nicaro, Cuba. The most extensive work was done with nickel sulfate-ammonium fluoride, ammonium fluoride, ammonium sulfate, and nickel sulfate-boric acid electrolytes. All four electrolytes exhibited some selectivity for dissolving nickel carbonate from Nicaro basic carbonate used for regeneration. The nickel sulfate-ammonium fluoride electrolyte exhibited less selectivity for dissolving nickel carbonate from Nicaro basic carbonate than it did from synthetic mixtures. Ammonium fluoride leaching experiments showed that a low concentration and high temperature gave a good nickel extraction with C. P. reagents; however, this was not confirmed in tests using Nicaro basic carbonate. Electrolytic tests employing ammonium fluoride leach liquors gave no further separation, since approximately 90 percent of the cobalt was deposited at the cathode with the nickel.

Jan 1, 1958

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Siderley Fernandes Albuquerque

Devido à descoberta de petróleo em um gigantesco reservatório situado na região litorânea entre os estados de Santa Catarina e Espírito Santo, a malha dutoviária brasileira irá aumentar consideravelmente nos próximos anos, assim como a necessidade de novos sistemas dutoviários capazes de transportar óleo e gás a pressões cada vez mais elevadas. A soldagem de tubulações no Brasil ainda é realizada de forma manual com processo ao Arco Elétrico e Eletrodo Revestido, fortemente dependente da habilidade do soldador; com a utilização de soldagem robotizada, tem-se maior controle dos parâmetros de soldagem, com possibilidade de obtenção de juntas de boa qualidade, além do ganho considerável em produtividade. O objetivo deste trabalho é analisar a tenacidade ao impacto charpy na ZTA de juntas soldadas do aço API 5L X80 utilizadas para transporte de petróleo quando submetidas a processo FCAW-G robotizado com o arame AWS E111T1-K3MJ-H4 para passes de enchimento e acabamento, com Ar + 25%CO2 como gás de proteção, e processo GTAW com o arame ER80S-Ni1 para passe de raiz, utilizado Ar + 25%CO2 como gás de proteção. Os resultados obtidos são comparados com o processo SMAW manual, utilizando como consumíveis os eletrodos AWS ER 7018 e E9010-G; as soldagens foram realizadas na posição plana e vertical ascendente; com os resultados obtidos de energia absorvida em ensaio de impacto charpy, com entalhe localizado na ZTA, foram correlacionados estes valores com a microestrutura presente na ponta do entalhe dos corpos de prova.

Aug 16, 2017

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By Philip J. Bangerter, Chris Twigge-Molecey

Design for safety is critical to metallurgical plants, due to the inherently dangerous nature of their processes. Two significant areas of concern are: 1. preventing catastrophic process failures that cause damage or injury; and 2. operational safety that directly affects those working in or living near the plant. Process safety involves human behaviour, but the designer can eliminate or control hazards by engineering approaches, and control impacts through the design of the operating procedures. The tools available to guide safe facility design include bowtie analysis, hazard analysis, and hazard and operability studies. Clean plant design principles can guide the design process to address in-plant occupational health and safety issues. Auditing and review is a key part of the overall design process.

Jan 1, 2015

By J. S. Miller

This report presents a complete coverage of results from Bureau of Mines preliminary research and the field application of explosive fracturing techniques to prepare oil shale for in situ recovery of shale oil. Small-scale surface tests were conducted to determine the feasibility of using a nitroglycerin-base explosive for creating rock fractures. Prior to underground testing, surface and near-surface tests with liquid explosives showed that explosions in sheetlike layers simulating underground fractures would propagate effectively. Successful surface experiments were conducted using layers of explosive placed between glass plates and explosive-saturated sand confined in small-diameter metal tubes. The tests in glass-plate reservoirs and metal tubes demonstrated that nitroglycerin would detonate and the explosion would propagate in cracks as thin as 1/32 inch and through distances up to 12 feet. In a shallow field test, nitroglycerin was detonated in a vertical crack in limestone and produced extensive fracturing. Explosive fracturing tests were performed in oil shale formations on seven sites near Rock Springs, Wyo. The procedures included (1) displacing and detonating nitroglycerin in natural or hydraulically induced fracture systems; (2) detonating nitroglycerin in wellbore shots; (3) displacing and detonating nitroglycerin in induced fractures followed by wellbore shots using pelletized TNT; and (4) detonating wellbore charges using pelletized TNT. The research on oil shale formations demonstrated that nitroglycerin displaced in a natural or hydraulically induced fracture would detonate, and the explosion would propagate through the explosive-filled fracture. Shooting a pattern of wells in oil shale at 100-foot depth with wellbore charges of pelletized TNT developed a satisfactory interwell fragmented zone. Tests performed on other sites at depths to 385 feet caused fragmentation of rock around the wellbore and provided interwell communication. Fourteen methods used to evaluate the extent and degree of fragmentation in the explosive fractured oil shale are discussed.

Jan 1, 1974

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By Mariana Gaudencio Barbosa Lima

O presente trabalho se baseia no estudo da recuperação de marcações adulteradas, em placas metálicas ferrosas, pela técnica de correntes parasitas (CP) /magnetografia (M) /visualização magneto-óptica (VMO) em comparação com o método destrutivo de restauração por ataque químico, utilizado pelos peritos criminais. Para tal, foram analisadas três amostras extraídas da sessão dianteira da estrutura do chassi de um veículo, as quais foram identificadas com caracteres impressos por indentações. Após a remoção das marcações por desgaste, as amostras foram analisadas pela inspeção CP/M/VMO e por ataque químico. Segundo os resultados obtidos, foi possível recuperar todas as identificações por ambos os métodos, além de compara-los segundo suas performances. Por conseguinte, a técnica não destrutiva demonstrou satisfatório desempenho na recuperação de marcações adulteradas.

Oct 30, 2017

By E. J. Murphy, John C. Holtz

"INTRODUCTION Toxic gases in the products from the detonation of explosives are one of the hazards in blasting underground. Investigations by the Bureau of Mines 4/5/ have shown that the oxygen balance of the explosive is an important factor in the control of toxic gases. This balance is considered in determining the composition of modern metal-mining explosives for blasting underground, and application of the concept has reduced the volume of toxic gases generated.The chemical nature of the material being blasted also influences the composition of the toxic gases produced. Under some conditions of blasting in massive pryrite, unsafe concentrations of sulfur dioxide and hydrogen sulfide have been found.Experiments with the O-J apparatus 8/ have shown that there is an increase in the volume of carbon monoxide in the gaseous products when permissible explosives are detonated in contact with coal dust. Thus, reactive materials of a reducing nature adjacent to explosives loaded in drill holes may decrease the effective oxygen balance of the explosive and cause the volume of toxic gases to increase.Several blasting accessories of reducing nature have been introduced recently for use in coal or metal mines or tunnels. In practice these are loaded adjacent to the explosive where conditions favor reaction with the products of detonation. The effects of this loading on the gaseous products obtained from the shot are indicated in this report. Broad consideration was not given the efficiency, usefulness, or over-all safety of these devices, but the practical significance of the hazard resulting from increased volume of carbon monoxide is discussed."

May 1, 1942

By Levent Ozdemir, Bjorn Nilsen

For several recent TBM tunnel projects, unexpected ground conditions have been encountered, causing extra cost, considerable delay, and in some cases major claims. Undoubtedly, insufficient and/or irrelevant site investigation and testing are among the main causes of such incidents. The purpose of this paper is to review the main investigations and tests relevant for hard rock TBM projects, with particular emphasis on the considerable development that has taken place over the last few years. Also, guidelines for defining optimum scope and extent of site investigations and testing are discussed, as well as the importance of adjusting the investigations and tests according to complexity of the ground conditions and project type.

Jan 1, 1999

By Scott G. Britton

Today's coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983