Search Documents

By AIME AIME

QUALITY and size do not ordinarily go hand in hand, but there is good evidence that both these attributes reached a new peak at the Annual Meeting of the Institute in New York just concluded. Certainly, the total attendance of 2500 was far above any yet attained, as might be expected with the recent rapid growth of Institute member- ship. General comment indicates that the quality of the papers also was notable, though not measurable by so definite a yardstick as attendance. During the meeting 49 technical sessions were held, at which more than 250 formal papers were presented. In addition, there were some thirty special meetings of committees, Divisions, and other Institute groups. In reporting the Annual Meeting eleven years ago the statement was made that "unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger," and "the fifth floor, where a buffet lunch is served each day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size." Unfortunately the angel to succeed Andrew Carnegie, who financed the building of the present home of the Institute 35 years ago, has not yet ' appeared. Even if some one would merely build another elevator or two in the present building it would help. Fortunately, the modern auditorium of the American Radiator & Standard

Jan 1, 1940

By M. J. Preim

Two case histories are presented on the evaluation of static bearing capacity of piles driven in soils that exhibit time dependent strength changes. Under consideration are a steel and a concrete pile driven into soils generally consisting of silty and clayey fine sand. Pile dynamic measurements and analyses were performed on both piles during initial installation, and also during restrike one week later. This information was used to predict each pile's long term capacity (defined as 14 days after initial drive), which was then compared to that measured with a static load test. Agreement between predicted and measured capacities were remarkably good, with an average error of only 4.5 percent. Two weeks after driving, total pile capacities were three times those at the end of drive. If only the skin friction was considered, however, it increased by an average factor of 16. The increase in pile capacity was determined to be linear over the time period considered.

Jan 1, 1989

By Meagan S. Boltz

From October 2000 to April 2001 a local array of fourteen seismograph stations was deployed at the Trail Mountain Mine (TMM), an underground coal mine in Emery County, Utah, to locate mining-induced seismicity (MIS). Original analysis of the data provided epicentral locations that coincided closely with the active longwall panel. The original analysis yielded poor quality hypocenters, however, preventing a useful relation from being made between mining activity and the event depths. For the original analysis, only stations at elevations above mine level were used for locating MIS. As a result, P- and S-arrival times from four of the stations in the local array were not used: an inmine station and three stations at elevations below mine level. This study compares mine workings and active mining to a revised TMM dataset that included P- and S-arrival times from the lower elevation stations that were not used in the previous study. In the revised locations, a modified master event methodology was used to calculate station delays. These station delays correct for errors in the shallow layers of the velocity model. The resulting hypocentral locations have improved depth resolution, determined by a lower root mean square (RMS) for the locations, compared to the original study. Most of the events occur in the roof of the mine and follow the longwall panel. When located using the velocity model determined in the original study, the elevations of the events increase as the longwall panel progresses. One possible explanation for the elevation increase is that it may be related to geology or the caving process. As presented here, a 10% decrease in the shallow velocity structure results in a more plausible location for the hypocenters. Consequently, it is hypothesized that progressive development of the TMM longwall panel(s) may have resulted in a progressive change in the velocity model.

Jan 1, 2012

Os mais importantes processos de redução de minério de ferro em fornos de cuba convivem, com maior ou menor intensidade, o problema de precipitação de carbono no interior de seus reatores. Para melhor conhecer os efeitos dos parâmetros operacionais desses processos sobre as cinéticas simultâneas de redução das pelotas de minério de ferro e de precipitação de carbono, foi definido um programa cooperativo entre a Samarco e o Grupo de Siderurgia da PUC-Rio. O presente trabalho é a parte 1 deste programa, que analisou o comportamento de pelotas RD nas temperaturas de 500, 700 e 900 °C, vazões de 60 e 90 NL/min e pressões de 1,2 e 2,5 atm, quando reagiram com os gases de topo e sopro típicos das regiões superiores (Zona de Redução-ZR) dos fornos de produção de ferro esponja (DRI). O tratamento dos resultados obtidos nos testes programados pelo método estatístico fatorial, permitiu identificar as cinéticas concorrentes e propor um modelo global baseado no principio da superposição. Finalmente, utilizando as curvas “Grau de Reação Global-GR versus tempo”, mostrou correlações plenamente compatíveis com os dados experimentais levantados e plena viabilidade de aplicação a outros processos de produção de ferro primário.

Aug 1, 2018

Near-Infrared Spectroscopy (NIRS) Sorting in the Upgrading and Processing of Skorpion Non-Sulfide Zinc Ore In 2008 Anglo American sponsored a research project at RWTH Aachen University to assess the feasibility of the use of near-infrared spectroscopy (NIRS) for ore waste discrimination at the Skorpion zinc mine. The Skorpion mine is an open pit zinc mine located in Namibia, owned by Anglo American with an annual production of 150 000 t/a of super high grade pure zinc. Opportunities for the implementation of NIRS sorting for the Skorpion process exist to upgrade currently subeconomic material, including the marginal dump (over 2000 000 tonnes, av grade of 2.5 per cent Zn). NIRS sorting is not yet implemented or established in the minerals industry however it is a proven technology in the plastics recycling industry, where more than 2000 NIRS sorters have already been installed. NIRS sorting, a type of sensor-based sorting, is a single particle sorting technique which classifies the particles based on the absorbed/reflected radiation in the near-infrared (NIR) region. A disadvantage of NIRS is that it is a surface measurement technique, but NIRS sorting shows overall great potential for the minerals industry. Skorpion ore minerals include zinc bearing phases such as sauconite, hemimorphite, smithsonite, and hydrozincite. These display diagnostic responses in the near-infrared. There are three major absorption features that characterise the reflectance spectra of the ore bearing minerals. These are due to OH and H2O molecular bonds. The spectral response of the waste material is caused by other minerals such as non-zinc-bearing clay minerals, calcite and impure quartz. Test work showed that it is theoretically possible to separate ore material from most waste material based on spectral response in the NIR region. In addition to upgrading material by removal of waste it is also potentially feasible to classify the material based on zinc grade. A tentative correlation between zinc grade and spectral response seems to exist for the sample test suite in the NIR region.

Sep 13, 2010

A quantitative chemical model of the rocks of the Broken Hill lode environment is presented to illustrate a stratiform orebody in a meaningful form to scientists interested in environmental control on the chemicalcomposition of sediments.Even though this study was restricted by the narrow range of rock analyses available it is obvious that significant chemical differences exist between the various rock units and also that some association of metallic sulphides with Ca, Mn, Fe, and P is indicated.Correlation of this evidence with that from other mining fields may point out more definite chemical relationships and elucidate the puzzle of the mode of formation of many stratiform orebodies.

Jan 1, 1968

By Shawn Healey, Ray Norcross

"Site IdentificationNew Britannia MineA 50/50 WX Gold Inc. - High River Gold Mines Ltd. Joint VentureTVX Gold Inc. is the OperatorLocationThe New Britannia Mine is located in the town of Snow Lake, Manitoba, which is situated between Flin Flon and Thompson, 420 miles north of Winnipeg.Brief Description of OperationNew Britannia Mine processes 2000 tonnes per day at an average grade of 4.5 g/t. Mill recoveries are currently 91 YO, accounting for forecast of 98,000 ounces for 1998.New Britannia Mine's mill complex incorporates conventional crushing, grinding and carbon-in-pulp technology. The design capacity of the New Britannia Mine mill is 1850 tonnes per day. The mill has processed upwards of 2300 tonnes per day, with no required upgrades.Gold recovery averaged 89.8% for 1997 compared to the planned 87% recovery expected from projected metallurgical test work. Year to date recovery mid December 1998 stands at 91.1 %Cash costs for the 1998 year to date were down to U.S. $221.49 per ounce, down 12% from the 3rd quarter of 1997. Milling costs for 1998 YTD were at Cdn. $9.38 per tonne and Cdn. $73.50 per ounce.Geology - (Orebody Description)The Snow Lake gold deposit is located within the Aphebian Flin Flon / Snow Lake Greenstone belt. This belt is composed of an assemblage of poly-deformed volcanosedimentary supercrustal sequences intruded by pre and sin tectonic ultra mafic and mafic intrusions and sin to post tectonic granitoid.The principal gold bearing rock at the New Britannia Mine is made up of quartzcarbonate material in sequence of basic and acidic volcanic rocks contained within a shear zone. The ore itself is gold associated with the sulphide mineral arsenopyrite and contains some pyrite, pyrotite, plus chalcopyrite. Proven and probable reserves at December 31, 1997 were at 4.04 million tonnes at 4.6 g/t and underground exploration continues to confirm the extension of the ore zones to depth."

Jan 1, 1999

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By J. R. Nettle

The purpose of these studies by the Federal Bureau of Mines was to determine the feasibility of refining low-grade hafnium by an inert-gas-shielded molten-salt electrorefining technique to produce a hafnium metal meeting reactor specifications. The techniques were adapted from those used success-fully for titanium electrorefining. Three electrolytes containing hafnium chlorides were developed from which deposits having a Brinell hardness of 170 or below were recovered. A KC1 + NaC1 + HfC14 electrolyte produced deposits in the hardness range of 140 to 165 Brinell. Deposits with a hardness range of from 132 to 152 Brinell were pro-duced from an electrolyte composed of KC1 + LiC1 + HfC14. A third electrolyte composed of NaC1 + K3HfC17 produced deposits with a hardness as low as 139 Brinell. In a fourth electrolyte, composed of NaC1 + K2HfF6, a measure of refining was accomplished, but under the test conditions no metal meeting specifications was recovered; none was softer than 174 Brinell. A number of metallic impurities were reduced in quantity by the electro-refining process, notably iron, which normally was reduced from 250 p.p.m. to less than 50 p.p.m. Magnesium generally was reduced from 680 p.p.m. to less than 80 p.p.m. Manganese content was also reduced by the electrorefining process. Sponge containing 90 p.p.m. Mn yielded deposits containing a maximum of 50 p.p.m.; some deposits contained only 10 p.p.m.

Jan 1, 1961

By Sandeep K. Sharma

The U.S. Bureau of Mines has been investigating new techniques to improve the of mineral to recover water lost in the waste slurry, and to produce dewatered solid dewatering s suitable for disposal. As part of this investigation, a study was undertaken to investigate the feasibility of dewatering Alaska placer effluent. Based on the laboratory tests, preliminary field tests were conducted on three placer mines in Alaska. At these mines, the water recovered from the placer effluent (250 to 23,000 NTU) exhibited turbidities of 20 to 240 NTU. In the second year of the project, a large-scale dewatering unit was set up at a mine located in the Livengood district. The feed, at flow rates up to 935 gpm, was mixed with dilute PEO solution in a flexible plastic hose with and without static mixers. Feed to the dewatering unit generally ranged between 300 and 26,500 NTU and required PEO dosages of 0.02 to 0.14 lb per 1,000 gal to produce water from the screen underflow with turbidities of 20 to 50 NTU. During this period, a small unit was also operated at Dow rams of 10 to 25 gpm at sewn sites throughout Alaska, with the effluent from four of the sites being dewatered successfully.

Jan 1, 2010

Bio-Oxidation of Arsenic and Stibium Bearing Gold Ores Bio-oxidation of arsenic and stibium bearing gold ores with acidithiobacillus ferrooxidans was studied. The preoxidation results show that the best bio-oxidation technical parameters are the initial pH in the range of 1.8 ~ 2.0, particle sizes under 0.074 mm, temperature in the range of 25¦C ~ 30¦C and rotating speed of the orbital incubator in 100 rpm ~ 160 rpm. The leaching results show that If the ore, of which contain 10.37 per cent arsenic and 36.81 per cent stibium, is not bio-oxidised, gold leaching is only about 41 per cent, after 8 days oxidised, the result is about 76.55 per cent, which improved about 35.62 points. The relationship between gold leaching and arsenic oxidation is direct proportion, furthermore, it needs only partly oxidise and higher gold leaching could be get, for example, gold leaching is over 90 per cent when asenic oxidation is 60 per cent. The results will provide theoretical and technological supports of bio-oxidation arsenopyrite for pretreating refractory gold ores.

Sep 13, 2010

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By Alejandro Berrios, Matheus DaSilva, Erick Siqueira

Vazante mine is an underground polymetallic mine that produces zinc, lead, and silver, which belongs to Nexa Resources in Minas Gerais, Brazil. The mine, a sublevel stope underground mine, mainly applies two subvariants: VRM – Vertical Retreat Mining and Open Stope. In a specific place of the mine, the geology allowed the design of a production stope with larger dimensions than the standard stopes, commonly called Super Stope. At this place, the plan was to apply both sublevel variants simultaneously. This mining block comprises rings in two different levels, with access by two ore drives on each level; the dimensions would be approximately 50 meters high, 50 meters long, and 35 meters wide. Opening the Free Face to mine the whole Stope was a challenge due to operational issues, such as hazard risks from loading over void space, exposure to uncontained places, and the impossibility of implementing the optimal blast sequence. Wireless blasting initiators have gained popularity recently due to their convenience, safety, and efficiency. This initiation system was applied to preload all the rings required to open the Free Face, ensuring a safe and optimal blast sequence. Wireless initiation prevented hazard risks, enhanced the blast sequence to guarantee the required void space, and optimized the equipment's operational cycle. The blast crew carried out the activity without exposure to the risk of loading over void space. The wireless detonators also avoided after-blast activities, which were required to provide secure access to the blast crew, optimizing the operational cycle.

Jan 21, 2025

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract No. HO395132 to develop and fabricate gas sensors for mining applications. Promising new instruments have been designed, developed, tested and supplied to meet BuMines requirements. These instruments include prototype 1) remote-sensing, diffusion-type CO monitors for mine operation which can be operated in conjunction with a surface computer, 2) control modules for alternate in-mine readout of the remote diffusion type CO monitors, 3) personal CO diffusion-type dosimeters and 4) personal NO diffusion-type dosimeters. In addition, retrofit modifications were made to update and optimize operation of CO and NO2 direct-reading type detectors provided under a previous contract. Studies were conducted to evaluate and demonstrate the availability of stable, portable N02 calibration sources for NO2 instrumentation. The use of selected, commercially available cylinder sources for NO2 instrument calibration were recommended. Additional studies were also conducted to investigate the feasibility of instrumentation for rapidly monitoring CO, NO and NO2 in diesel exhaust.

Jan 1, 1981

By Joe Zhou

"Mineralogical characterization and metallurgical extraction of silver is challenging due to its complex mineralogy and chemistry. Over 200 Ag-bearing minerals have been identified and a silver-rich ore body would typically contain 5 to 10 different silver minerals. Silver can occur not only as discrete microscopic (visible) silver minerals but also as submicroscopic (invisible) silver in other minerals. During processing, silver may form passivation compounds such as silver hydroxide, silver sulphide, jarosite-like silver sulphate, silver halide or silver cyanide precipitate, all of which may negatively impact on silver extraction. Knowing the deportment of silver in the ore and its metallurgical products is important in flowsheet design and plant optimization. This paper begins with the classification of silver ores and minerals and a review of processing techniques, and focuses on the major mineralogical factors to explain why and how these factors affect silver extraction. Case studies are provided to demonstrate the application of silver process mineralogy in flowsheet design and plant optimization.INTRODUCTIONSilver was known to and utilized by mankind since ancient time. Actually, it was one of the earliest metals discovered and utilized by mankind after gold and copper.Silver is the whitest metallic element. It is rare, strong, corrosion resistant, and unaffected by moisture, vegetable acids, or alkalis. Silver is also resonant, moldable, malleable, and possesses the highest thermal and electric conductivity of any substance. The chemical symbol for silver is Ag, from the Latin argentum, which means white and shining. Although silver does not react with many chemicals, it does react with sulfur, which is always present in air at trace amounts. The reaction causes silver to tarnish, and consequently it must be polished periodically to retain its luster.Silver possesses many special physical characteristics and qualities that make it useful to a variety of industries. The photography industry is the biggest user of silver compounds. Silver forms the most light-sensitive halide salts, which are essential to developing highquality photographic prints. Silver also has the highest electrical conductivity per unit volume of any metal, including copper, so it is used extensively in electronics."

Jan 1, 2010

By James W. Hendrix

A survey of endomycorrhizal fungi occurring on orphan coalmine lands in Western and Eastern Kentucky revealed a great diversity of species present. Thus a large number of fungi are available for isolation and evalution for enhancing revegetation of mined land. Endomycorrhizal fungi isolated from orphan mines stimulated growth of sweetgum seedlings on mine soil at low fertilisation but inhibited growth at high fertilization; this growth inhibition at high fertilization did not occur with plants growing on peat-perlite. Banding of endomycorrbizal inoculum was not advantageous, compared with incorporation of inoculum throughout the growth medium, for production of mycorrhizal sweetgum seedlings. Newly reclaimed mine spoils were nearly nonmycorrhizal, compared with land reclaimed four or eight years earlier. A procedure for isolation of single-spore cultures of endomycorrhizal fungi was developed; this procedure is necessary for studies of ecotypic variability. A practical procedure using container-grown Pisolithus tinctorius-infected shortleaf pine seedlings for production of large numbers of bareroot pine seedlings infected with P. tinctorius for mined land reclamation was demonstrated.

Jan 1, 1982

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By D. C. Bailey, D. I. Hodson

Paper presented at the annual joint meeting of the IMM and IMinE held in Harrogate, 31 January 1991. The Neves-Corvo copper-tin mine is the highest-grade large-tonnage copper operation in the world and is now arguably the most significant producing base-metal mine in Europe, rating in the top ten world producers of both copper and tin. A description is given of the initial exploration work and the development of the project from the orebody discovery in the Iberian Pyrite Belt of southern Portugal in 1977 to full operating capacity in 1990. The chronological account includes discussion of the main organisational, financial, technical and environmental decisions and of the various difficulties encountered, and the challenges of the future are identified. The project was brought in on schedule and within budget

Jan 1, 1991