Search Documents

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

THIS paper is the outcome of experiments carried on and experience gained. at the Waihi-Paeroa Gold Extraction Company's tailings plant at Waihi, New Zealand. The plant was erected to treat accumulated tailings which had been discharged into the Chinemuri River by the Waihi batteries.The Chinemuri River is a common sludge channel for all mining debris, tailings, and ashes from the power plants, the last being the cause of occasional high residues, which gave so much trouble to the management. The tailings were dredged from the bed of the river into barges by means of a Pohle air lift, the power being supplied: by a 13 b.h.p. Tangye oil engine driving an air compressor and a centrifugal pump. The sands were elevated from the barges by bucket-belt elevators over screens, to eliminate large particles and rubbish, into storage hoppers, and from there fed direct into four C. Judd Ltd. tube mills.The method of treatment was fine grinding in a weak cyanide solution, agitation in B. and M. tanks, filtration with turn-over vacuum filters, and precipitation with zinc shavings. The comparatively high values of the residues in gold gave a great deal of trouble, 'and it was not until repeated experiments were carried out that the cause of the trouble was located. While the value of silver residues remained stationary, the gold values...

Jan 1, 1912

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By J E. Nethery

At the Red Dome and Mungana deposits in north Queensland, Australia, it is proposed that mineralisation and alteration developed as a 'telescoped' overprinting continuum, ranging in style from hypothermal to epithermal, reflecting the major changes that developed in the regional setting over the period circa 325 - 290 Ma. Regional assessment suggests that this also applies to many other precious and base metal deposits within a 40 km length of the host Siluro-Devonian Chillagoe Formation.   A ten stage paragenetic sequence of structural preparation, multi phase intrusion and associated mineralisation, alteration and brecciation is postulated for the Chillagoe district.

Jan 1, 1995

By L. F. Bishop

THE ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square-sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill fs a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various meth: ods in use for the second six months of 1944 are shown in Table I. [ ] This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1945

By V. Coetzee

In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes. Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum.

Jan 1, 2006

By Tatiane Potiguara Oliveira

O compósito metal-cerâmico Al2O3 – Cu alia as propriedades de baixa densidade, alta resistência ao desgaste, dureza e biocompatibilidade da fase cerâmica alumina a excelente condutividade elétrica, e alta tenacidade do cobre metálico. Tal compósito pode ser aplicado como ferramenta de corte, entre outras. Este trabalho discute a influência da moagem de alta energia na microestrutura e densificação do compósito Al2O3–Cu. Pós de Al2O3 e Cu na razão de 5% em massa de Cu foram moídos por até 100 horas em moinho planetário de alta energia. A razão em massa de pó para bola usada foi de 1:5. O álcool etílico foi usado como solvente. Na moagem, amostras de pós foram colhidas após 2, 10, e 50 horas. Pós moídos foram prensados uniaxialmente em matriz cilíndrica a 100 MPa e sinterizados a 1.300°C por 1 hora sob atmosfera de Ar e H2. A taxa de aquecimento foi de 10°C/min. Análises de DRX, AG caracterizaram os pós moídos. O MEV e o EDS foi empregado para observar a microestrutura das partículas dos pós moídos e dos corpos sinterizados. Um pequeno tamanho de partícula da fase cerâmica e uma estrutura mais homogênea são produzidos quando os pós foram moídos até 100 horas.

Aug 8, 2018

By Antonio Mendoza

El presente trabajo señala una metodología en gestión de seguridad, la cual proporciona un enfoque estructurado de procesos que permite la solución de problemas y facilita la toma de decisiones basadas en datos. Esta acción es una herramienta de gestión de seguridad aplicable a todos los aspectos de productividad, calidad y seguridad. Por tanto, se convierte en un instrumento de uso general a nivel de supervisión que faciilita la toma de acción correctiva de forma oportuna en la mina Quiruvilca, reduciendo los accidentes capacitantes en la industria minera.

Sep 13, 2001

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

By V. T. Dow

Although the titaniferous iron occurrences at Iron Mountain have been known since 1850, exploitation of the deposits has been discouraged by the metallurgical difficulties encountered in treating the complex magnetite-ilmenite material. Because of the intimate association of magnetite and ilmenite, the material is not amenable to known ore-dressing practices. During World War II, industries started moving south and west from the industrial East; iron-ore reserves in the East were being depleted at a rapid rate; and titanium came into demand as a pigment. Imports of ilmenite from India, then the main source, were practically suspended because of lack of shipping space. These factors created interest in possible exploitation of the Iron Mountain deposits as a source of iron and titanium.

Jan 1, 1961

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates (or sodium-free compounds) are required for certain end uses, but in general, nonsodium borates are used only where borax is not avail- able. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of about a million tons of B2O3. Leadership in supplying borates has shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates. In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, Calif., is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, Calif., the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "lo-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7- lOH2O. In addition to ship- ping all major refined borate products from Boron, the company ships semiprocessed ore concentrates to treatment plants elsewhere.

Jan 1, 1975

By F. S. Crawford

The average visitor to a large electric-shovel operation may wonder how electric power can be treated as carelessly as apparently it is in open-pit mining, and how the mining company can string it carelessly along the ground in great, black, hoselike cables, whereas the power company, which has learned to respect his deadly agency, keeps power lines far out of reach. This is explained by the fact that this particular kind of application of power to moving machinery requires the use of trailing cable instead of the more permanent type of construction that permits a moving contact, such as a trolley. The cables are designed to insulate fully the enclosed power lines against damage and loss of current; and employees are taught to handle them carefully, although engineers are not satisfied that the trailing cable is foolproof and are seeking constantly to improve methods and equipment to insure greater safety. In some sections they rely mainly on the construction of the cable and perfection of equipment, while in others additional precautions are taken, such as handling the cable with rubber gloves, slings, tongs, or loops. In some sections no temporary repairs are made to cables, while in others such repairs are made and later are vulcanized in the shop. At some operations the cycle of shovel duties is arranged so that cables are very seldom exposed to flying rock fragments while at others this exposure appears to be unavoidable. Methods of fastening the cable to the shovel frame and transporting the loose cable vary. Inspection and care of the cable are important in insuring its safety and durability. A limited amount of information was obtained by field engineers of the United States Bureau of lines from operators in various parts of the United States, as methods of handling electric-shovel operations differ with the districts; practices followed and equipment used in these districts are described in this circular.

Jan 1, 1936

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By R. H. King

Suboleski and King (1990) analyzed the reasons for the dramatic increase in underground coal mine productivity during the last 10 years. This paper examines whether this increase can be extended. The paper forecasts whether the mix of technological, procedural and other factors that produced the increase will change in the future. The forecast is based on the base case and spreadsheet production model described in the previous paper.

Jan 1, 1991

By Fernando de Souza Costa

Nos últimos anos a indústria automotiva vem conseguindo avançar de forma contínua em relação ao controle da emissão de CO2 e no tocante à segurança veicular. O aumento da utilização de aços de alta resistência mecânica se constitui num dos principais sustentáculos destas melhorias. Além disso, na manufatura de certas peças, em especial as de geometria complexa, é fator crítico de sucesso a capacidade do material em absorver intensas deformações localizadas, tipicamente encontradas em operações de expansão de furo. O aço desenvolvido pela Usiminas é um produto laminado a frio, com revestimento eletrogalvanizado, da classe de 600 MPa de limite de resistência, com boas propriedades de flangeamento de bordas e de alongamento em tração. Neste trabalho, é apresentado o desenvolvimento deste aço. São descritas as suas principais características e os resultados de sua aplicação em uma peça de geometria complexa.

Aug 17, 2017

By Jorge Meza

El presente texto señala el diseño de controladores en los hornos de fusión de concentrados de cobre a través de la lógica difusa. Para ello, se simuló dinámicamente el proceso de fusión de concentrados de cobre de un horno de tecnología Isasmelt, incluyendo su actual sistema de control y subsistemas convencionales (PID), para representar sus principales parámetros termodinámicos, y de esta forma, obtener una base de medición. Posteriormente, se desarrolló el sistema de control avanzado con la teoría de lógica difusa, que fue incorporado en el módulo de simulación del horno, para comparar su performance con la del controlador convencional.

Sep 24, 2008