Search Documents

By R. John Caulfield

The primary water supply system for the City of San Francisco and adjacent peninsula areas consists of aging and deteriorated pipelines crossing under the San Francisco Bay (the Bay). This system is highly vulnerable to seismic damage from the nearby San Andreas and Hayward fault zones. The Bay Tunnel Project will replace the existing system with a 8-km-long (5-mi-long) tunnel underneath the Bay. The tunnel will be constructed using earth pressure balance methods and will have a two-pass lining system of precast concrete bolted, gasketed segments for initial support, and a welded steel pipe final lining. The project challenges include tunneling through both soft ground and rock conditions without any intermediate shaft access over the entire alignment. Seismic performance criteria include maintaining service flows after a large earthquake.

By Paul M. Tyler

One by one new metals come to share the burden of modern industry. Long before the Christian era potters and glass workers employed fine and costly blue pigments that contained cobalt. Cobalt blue class has been found in the tombs of the Egyptians and in the ruins of Troy, and many of the colors used by the ancient Greeks and Romans contained cobalt. The ancients, however, were apparently unaware that the colors they used were caused by cobalt, and it was not until late in the 17th century that the existence of the element was recognized, Writers in the Middle Ages referred to "cobalos" as an evil spirit that haunted mines and caused trouble to the miners. Subsequently the German worms "Kobold," meaning goblin, came to be applied to any baffling mineral and particularly to minerals that resembled ores but failed to yield metal when smelted. Even to-day there is something of an air of mystery about cobalt, and a medieval cloak of secrecy still surrounds many of the metallurgical processes employed in its production. "Zaffre" was mentioned about the middle of the sixteenth century by Biringuccio, and in 1735 the metal war, first prepared by G. Brandt. To preparation of cobalt compounds, however, must have been carried on in at least a small way ever since the opening of the silver-cobalt deposits of Schneeberg in 1470. By 1790 there were 25 works engaged in the industry, rust of them located in Saxony, but the total output of these works probably did not exceed 300 tone of cobalt annually, mostly in the fore of smalt. The smalt which contained approximately 6 per cent cobalt was sold in Venice in 1520 at about 16 cents a pound. A few refineries in Holland supplied the Irish linen trade, contributed a farce amount to the Dutch linen industries, and alto provided smaller quantities for the manufactuer of litmus in Holland. A complete description of the early [histor,] of the cobalt industry in Saxony, is given by Mickle in the Deport of the Bureau of Mines of Ontario, vol. 19, 1913, pt. 2, pp. 234-251.

Jan 1, 1930

By B. Haimson

A new loading apparatus was fabricated and used to conduct true-triaxial compression tests on KTB amphibolite, a crystalline basement rock. Tests in dry jacketed samples reveal that the intermediate principal stress has a significant effect on the onset of dilatancy and on rock strength, contrary to the implicit assumption made by Mohr-type failure criteria. Failure is induced through a shear fracture that dips steeply in the direction of the least principal stress. Experimental results lead to a new generalized strength criterion in terms of all three principal stresses. Unjacketed KTB amphibolite specimens, exposed to confining fluid, are considerably weaker than the jacketed ones, despite the negligible porosity and permeability. Failure is facilitated by several closely spaced subparallel tensile cracks normal to the least stress direction. SEM analysis suggests that microcracks developed upon dilatancy onset are penetrated and extended by the confining fluid, bringing about the unexpected rock failure mechanism at reduced stress levels. Un nouveau dispositif à chargement fut fabriqué et utilisé afin de réaliser un vrai essai de compression tri-axial sur KTB amphibolite, une roche cristalline du sous-sol. Les essais effectués sur échantillons enveloppés et secs révèlent que les contraintes principales intermédiaires affectent considérablement le début de la dilatance et la résistance de la roche, contrairement à la supposition fondée sur le critère de rupture de Mohr. La rupture est produite grâce à une cassure de cisaillement très incliner en direction où la contrainte principale est moindre. Ces résultats expérimentaux indiquent un nouveau critère de rupture général en fonction des trois contraintes principales. Les échantillons de KTB amphibolites sans enveloppe, exposés à un liquide confiné, sont considérablement plus faibles que ceux enveloppés, malgré la porosité et la perméabilité négligeable. La rupture est facilitée par plusieurs fissures de traction adjacentes et sub-parallèles, normales à la plus petite contrainte principale. L’analyse SEM suggère que les micro-fissures développent suivant le début de la dilatance, elles sont pénétrées et agrandies par le liquide confiné, produisant un mécanisme de rupture de roche inattendu, ceci à un niveau de contrainte réduit. Ein neuer Ladungsapparat wurde hergestellt um real - triaxiale Druckfestigkeitsversuche in KTB Amphibolit, einem kristallinen Grundgebirgsgestein, durchzuführen. Messungen in trockenen, bedeckten Proben zeigen that die mittlere Hauptspannung eine bedeutende Wirkung auf das Einsetzen von Dilatanz und auf die Stärke des Gesteins hat, im Gegensatz zu der impliciten Annahme auf Grund von Mohr-ähnlichen Versagungskriterien. Versagen ist induziert durch eine Scherfraktur die sich steil in die Richtung der geringsten Haupspannung nach unten senkt. Messergebnisse führen zu einem neuen, verallgemeinerten Stärke Kriterium dass auf alle drei Hauptspannungen basiert ist. Unbedeckte KTB Amphibolit Proben, die unmittelbar den umgebenden Fluiden ausgesetzt sind, sind wesentlich schwächer als bedeckte, trotz geringfügiger Permeabilität und Porosität. Versagen wird gefördert durch mehrere, nebeneinander liegende, sub-parallele Spannungsbrüche, normal zu der geringsten Spannungsrichtung. SEM Analyse lässt vermuten dass Mikrobrüche, die sich beim Überschreiten der Dilatanzschwelle entwickeln, durch die umgebenden Fluiden fortgepflanzt und weiter verbreitet werden, und unerwartet, auf Grund der reduzierten Spannungswerte, den Versagungsmechanismus des Gesteins einleiten

Jan 1, 2003

Rockbursts continue to be a scourge in the mining industry, being responsible for accidents and damage to mining excavations. Although the problem has been present for more than a century, and although much research has been carried out, a solution is still elusive. Determination of, firstly, the demand on the support system imposed in the rockburst and, secondly, the capacity of the support system, cannot be carried out with any confidence, and therefore rockburst support cannot be designed using a conventional design approach. In contrast with the conventional approach, observations of rockburst damage in a mine have revealed a possible alternative approach to rockburst support ? sacrificial support. It was observed, in rockburst events, that a support system consisting of concrete panels restrained by grouted cables was destroyed, and the concrete panels were ejected. However, the rock behind the panels remained apparently undamaged and in place. This behaviour reignited the concept of sacrificial support, conceived more than 20 years ago, and which is described in this paper. The remedial solution implemented on the mine, involving cables wrapped over the panels and retained by grouting into boreholes, has been subjected to rockburst loading and has confirmed the validity of the sacrificial support concept. The concept of sacrificial support may be controversial, but is deliberately presented here with the aim of generating discussions and contributions, and with the ultimate aim of improving safety and reducing rockburst damage in mines. Keywords rockburst, seismicity, seismic waves, rock support, support design.

Jul 1, 2013

Hydrogen and carbon monoxide reduction data were obtained on pelletized materials of the type currently being prepared commercially in Australia.Pellets, approximately 1 cm diameter, made from Deepdale, Iron Prince, and Mt. Newman iron ore were reduced by hydrogen over the temperature range 500°-900°C and the reduced pellets were examined by thermogravimetric, microscopic, electron probe, and x-ray techniques. After an initial time delay it was found that up to 95 per cent reduction the data could be described by a porous model where gaseous diffusion through the solid is rate controlling. Independent measurements of effective diffusivity supported the values obtained from the reduction data. Above 95 per cent reduction the rate decreased markedly due to the formation of retained wustite or fayalite.Comparison with reduction by carbon monoxide over the temperature range 750°-900°C showed that the rate of reduction was approximately five times slower than for reduction by hydrogen.The rate of reduction was found to be a function of the initial properties of the pellets which may account for the widely conflicting results that have been obtained with previous investigations on porous pellets.

Jan 1, 1971

By D. Norval

Keywords: Pyrometallurgy, slag, metal, entrained, granulation, ferromanganese Water granulation of certain slags with high metal entrainment has customarily not been practised, not only due to the belief that such processes are too dangerous and unproven in the pyrometallurgical industry, but also that it might not be economically viable or environmentally acceptable. General slag granulation, on the other hand, is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. Thus, purpose-designed granulation and solidification processes are discussed, taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte, or alloy responds in similar fashion to a granulation practice. This paper addresses three issues, namely: ? Water-granulation of BOF steel slag, without processing it to render it environmentally safe, physically and chemically acceptable for use by the construction industry, and the process economical ? Processing air-cooled BOF steel slag to change its physical and chemical properties to be acceptable for various uses and extracting metallic and bound iron ? Processing air-cooled or molten manganese slag to lower its manganese content to a level that is acceptable from an environmental and health point of view, and extracting FeMn-alloy of acceptable composition. The latter process culminated in a patented process to extract FeMn from air-cooled and molten manganese slag, and, at the same time, produce a hydraulic (cementitious) slag, thus transforming a possible hazardous by-product into virtually 100% saleable products.

Jan 1, 2011

By A. B. Pederson, G. E. Bartlett

As a part of our study of how coal mine dusts injure the lung we have studied the effects of dusts and dust-exposed pulmonary alveolar macrophages (PAMs) on the growth of lung fibroblasts (LF). Fibroblasts were cultured near confluence in low-serum medium, either alone or in the presence of dusts, dusts plus PAMs, dust leachates or superriatants of dust-exposed PAM cultures. We report here provisional conclusions, based on initial observations. Rat LF were relatively unresponsive to direct effects of dusts, showing weak stimulation in only a few cultures, and there was no evidence that dust-exposed rat PAMs had released any growth-regulatory products. In contrast, guinea pig cells were more responsive to the dusts. The pattern of responses was quite complex. Three of the dusts stimulated LF directly (with no mediation by PAMs). Two dusts were essentially inert when added directly to fibroblast cultures, either with or without PAMs, but their leachates were active: 867 leachate was inhibitory and RF leachate was stimulatory. Dust 1361, either directly in the cultures or as an aqueous leachate, was stimulatory, and it activated cocultured PAMs to stimulate LF growth; however, supernatant products of 1361-stimulated PAMs were inhibitory. Direct exposure to 1192 stimulated LF, but its leachate was inert; cocultured PAMs exposed to 1192 had weak stimulatory effects, but supernatants of 1192-exposed PAMs were mildly inhibitory. MP3-3 had effects similar to 1192, except that the cocultured, dust-exposed PAMs had no effect on growth. We conclude 1) that guinea pig lung cells are more responsive to dusts than are rat lung cells, 2) that dusts can influence growth of LF by four kinds of interaction (by direct dust-cell interaction, by release of soluble dust components into the culture medium, by activating P AMs to exert direct cell-cell interactions, and by activating P AMs to release growth regulatory products into the culture medium), 3) that each kind of interaction may be neutral, inhibitory or stimulatory, depending on the dust tested, 4) that four of the dusts tested were neutral, inhibitory or stimulatory, depending on the assay (the fifth <lust was either neutral or stimulatory), and 5) that the effects of soluble mediators (leachates or products of activated PAMs) frequently did not correspond with the direct dust-cell or PAM-fibroblast effects. These results suggest that the nature of the dust-lung interaction at the level of cells and molecules is exceedingly complex. These observations need to be confirmed and extended to determine what characteristics of the dusts determine the nature of the cellular responses, and to determine which patterns of responses are detrimental and which are beneficial in the overall health of the dust-exposed lung.

Mar 1, 1989

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L&apos;Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l&apos;uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l&apos;épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

WHILE in the employ of the Broken Hill Associated Smelters and the Electrolytic Zinc Oompanies at their South Melbourne Research Station, the writer was detailed to investigate the principles underlying the Parkes Process with a view of determining:1. The Interdependence of the variables:(a) Quantity of zinc required per charge,(b) Temperature of stirring of each zincing,(c) Silver content of the bullion after first zinculg,(d) Silver content of the bullion after second zincing,(e) Silver grade of the crusts produced for retorting, with reference to the method of working the Parkes Process then in operation at Port Pirie.2. The possibility of effecting improvements in the Port Pirie practice of desilverising, especially with respect to:(a) Silver grade of the crusts produced for retorting.(b) Quantity of zinc required per charge.The method of desilverising in practice at Port Pirie was a two-stage zincing.In both zincings the bullion was cooled to its solidification temperature and the silver crusts which separated from the lead were completely removed.The crusts from the first zincing were retorted, and the crusts from the second zincing were returned to the first zincing of the next charge.

Jan 1, 1925

By Leslie F. Ruppert

The US Geological Survey (USGS) is currently conducting a coal resource assessment of the coalbeds and zones that are projected to provide the bulk of the nation’s resources for the next few decades. The Pittsburgh and Upper Freeport coals are the first two beds in the northern and central Appalachian basin region to undergo fully digital coal assessments. The bed-specific assessments are being carried out in partnership with the state geologic surveys of West Virginia, Ohio, Pennsylvania and Maryland. Comprehensive stratigraphic and geochemical databases have been developed for both of the beds. The extent of the bed with mined areas, structure contour, isopach, and overburden thickness maps for the Pittsburgh coal bed have been released as USGS open-file reports.

Jan 1, 1999

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By Will Jansen

When Enron rocked the United States with its Titanic-sized financial accounting scandal, miners and metallurgists were probably too busy on the mine sites in remote locations to wonder about its ripple effect. But then Enron sank, Arthur Andersen tanked and the list of scandals, costing billions of dollars, continued to ripple. Followed by the Public Company Accounting Reform and Investor Protection Act of 2002 (Sarbanes-Oxley), the recent credit crunch and weak economy, the currents from Enron?s collapse eventually washed right into the mine and the mill. These events placed intense scrutiny on metals production accounting processes as traditional semi-qualitative metal accounting practices provided insufficient credibility and transparency. ?There is growing intolerance of organizations that are unsure about the location of thousands of tonnes of ore, which will typically lose 10 to 15% of their notional value on the way to the concentrator,? Rob Morrison wrote in the opening chapter to An Introduction to Metal Accounting and Balancing. ?If the measurement and forecasts also contain qualitative (fudge) factors, a very real suspicion might emerge about just how much metal might disappear (by theft or misplacement) before detection becomes likely.? Metallurgical accounting, put simply, is the tracking and reporting of the quantity and quality (tonnage and grade, usually) of materials entering or leaving each stage from source to product for a specified accounting period. Lacking an accounting standard, metals accounting in precious metal operations has been performed in an ad-hoc, informal manner, leading to numerous errors and unidentified potentially significant inefficiencies and financial losses. As a result, mining companies are beginning to examine the quality of their metals accounting systems since they form the basis of mining company?s financial accounts and reports. As part of an effort to create that accounting standard in the mineral industry, University of Queensland?s Julius Kruttschnitt Mineral Research Centre published the textbook An Introduction to Metal Accounting and Balancing in 2009. While development of a textbook and standard are significant steps forward, the challenge in the precious metals industry is in the application of some of these suggested practices. Though improving process transparency and precious metals accounting reporting accuracy is a key driver for change from the financial side, perhaps even more important is the potential benefit to operational performance that comes with better measurement, accounting and reconciliation systems. Loss of precious metals, processing of waste and inefficient mining and processing systems are all problems that are faced in an operation on a daily basis that can help be resolved through improvements in metal accounting and reconciliation. The financial consequences of such operational inefficiencies and bad decisions based on poor information are arguably greater than consequences of fraudulent accounting. Large discrepancies between mine and mill measurement systems that measure the quantity and quality of valuable material currently exist. Some of these are expected because of statistical variation, but inherent random measurement variation is sometimes an insufficient explanation. Though the mill can usually make much better production estimates through their measurement systems (that is, less variation), this knowledge rarely benefits the mine. 3 Moreover, even if the mine does a reasonably good job of estimating expected production at the grade control level (in situ), issues such as blast movement, poor mining practice and inefficient ore/waste classification make for a disconnect between the in situ estimates of the mine and the estimates from the concentrator. This inhibits effective evaluation of the reserve and grade control models using concentrator estimates. Linking the two ends, mining and concentration, is a neglected area sorely in need of an overhaul. Hence the need for improved mine to mill reconciliation ? the area of comparing, balancing and adjusting production estimates between mine and mill for consistency in reporting.

Jan 1, 2009

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Feb 24, 1997

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014