Search Documents

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

The Environmental Excellence in Exploration (E3) project is driven by the recognition that the minerals industry can only maintain its long term viability by ensuring its continued access to lands to explore for, and develop, new mines. Widespread implementation of sound environmental management practices by the exploration community and improved education and understanding of that by stakeholders will help substantially in accomplishing this, and E3 is designed to meet these needs. Exploration crews are now viewed as ambassadors for the global mining community. Their performance in managing the environmental aspects of an exploration program can demonstrate a commitment on the part of the international mining sector to environmentally responsible exploration and mining. We have all observed that failure to behave responsibly can alienate local residents, encourage anti-mining NGOs and jeopardize development. As the saying goes, ?you don?t get a second chance to make a first impression?, and we want to make a favourable first impression. The E3 project is focused on creating an electronic manual, the e-manual, which will provide rapid access to the most up-to-date information on environmental management practices for minerals exploration globally. The e-manual will reflect current thinking and practices in environmental management. It will be richly illustrated with actual examples that reflect the realities of exploration. It will strive to identify the key environmental issues and concerns that apply to most exploration projects, and identify other sources of relevant information useful to field practice. It is our belief that E3, or something very like it, is central to ensuring that the industry survives the current challenges to its viability. E3 will be a cornerstone of the mining industry?s drive to sustainability simply stated, if we are not permitted to explore for mines, there will be none of them at some point in the relatively near future.

May 1, 2002

By Yunnen Chen

The test and use of natural materials as biosorbents for the removal of heavy metals from industrial wastewater is under constant development. In the present study, the biosorption capacity of waste microzyme was studied for cadmium The cadmium removal study has been carried out batchwise where the influence of physico-chemical key parameters such as pH value of solution, contacting time and initial cadmium ions concentration have been considered. The influence of metal ion concentration was evaluated and the results were fitted using adsorption isotherm models. The kinetic of cadmium biosorption was also investigated. The maximum percent removal was attained at the pH 7.0 after about 30 min. Waste microzyme was a potential biosorbent for the removal of Cd(II) from the effluent of electroplating industry.

Jan 1, 2009

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Jaeheon Lee, Junmo Ahn, Jae-Yeon Kim, Yoo-Jin Kim, Jiajia Wu, Eun-Woo Kim, Jai-Won Byeon, Jun-Jae Lee

The surge in demand for battery materials, coupled with environmental challenges linked to battery disposal, underscores the need to recycle spent lithium-ion batteries (LIBs). Green recycling approaches, in particular, have garnered attention for battery recycling. In this study, a hydrometallurgical method using a synergetic organic lixiviant combining methanesulfonic acid (MSA) and citric acid (CA) as an alternative to inorganic mineral acids was introduced as a green approach to recycle cathode materials of LIBs. The conditions for leaching and recovery processes were optimized. Cathode materials were regenerated using the recovered materials. Moreover, the leaching performance and economic feasibility of this leaching system were compared with those of various other organic acids.

Feb 1, 2024

By D Brooks, S Gunn, T Perkins, J Siliezar

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38km north east of Cloncurry. The EHM ore body has an average grade of 0.9% copper (chalcopyrite), 0.5g/t gold and 22% magnetite.Open pit mining commenced in March 1998, but EHM transitioned to underground mining in December 2012, extending the life of operations beyond 2024. The underground mine currently produces up to 3Mt/year of ore, hauled up a decline by truck. This figure shall double in 2014 with the completion of a 1000m shaft. The EHM Concentrator has a nameplate capacity of 10Mt/year. In June 2011, Xstrata Copper acquired the Mount Margaret resource to supplement underground production and utilise the full capacity of the Concentrator. The Mount Margaret Mining (MMM) operation was established to develop the five deposits making up the resource by way of open pit mining.Copper concentrate is produced by the EHM Concentrator via grinding, flotation and dewatering circuits. The grinding circuit comprises a SAG and ball mill in a closed AB configuration. Flotation consists of a rougher train, regrind and three stages of cleaning, with the tail from the first stage reporting to the tailings thickener.The mineralogy of the MMM ores is complex, comprising fine textures of active pyrite, copper oxides, native copper, clay and secondary copper sulphides. This paper provides an overview of the metallurgical test work completed to forecast the performance of the MMM ores through the EHM Concentrator and identify flow sheet modifications for maximising copper recovery and producing a saleable concentrate. A discussion of the challenges experienced in the plant to date follows.CITATION:Gunn, S, Siliezar, J, Brooks, D and Perkins, T, 2013. Adapting the Ernest Henry Mining concentrator to process the Mount Margaret ores, in Proceedings MetPlant 2013 , pp 347-370 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Carl F. Floe, Michael B. Bever

ACCELERATED by the demands of war, research and development work in nonferrous physical metallurgy has continued at a rapid pace during the past year. In particular, advances have been made in processing and fabrication, especially of the light alloys, and in the surface treatment of metals. Theoretical physical metallurgy, although less active, has not been neglected and the year has brought forth some -notable contributions to our understanding of the fundamental structure of metals and their behavior in service. Of course, much work that has been done cannot be publicly discussed because of wartime restrictions.

Jan 1, 1945

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

In a previous paper of this series (1) ,t it was shown that during the creep of single crystals of lead, deformation proceeded to some extent by means of slip on the octahedral plane. This was demonstrated by the formation of slip lines on the surface of the specimens. At first, a few broad bands appeared after a small amount of extension had taken place; then, as extension proceeded, more and finer lines made their appearance until the whole of the specimen surface was covered.The present paper deals with the process of deformation of the creep specimens as revealed by X-ray examination..By the use of this method, the changes taking place in the crystal structure can be observed.EXPERIMENTAL METHODThe method of preparation of the specimens, their size and the purity of the lead employed have been reported elsewhere (1). At frequent intervals, the specimens were dismantled from the test rack and X-ray back reflection photographs were taken. The specimens were so marked and set up on the X-ray machine that the same spot on the specimen surface was always examined.Copper radiation was employed, the tube voltage and current being 45 kV. and 25 m.a. respectively and the exposure time 2 hrs. The slit diameter was 1 mm.

Jan 1, 1941

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By O. H. Metzger

This is one of a series of capers being published by the Bureau of Mines on gold mining A the Western States. It describes the production of gold in the principal mining districts of New Mexico. The material was gathered red on a trip through tale State in the summer of 1936. ACKNOWLEDGMENTS The author acknowledges the aid and cooperation of mine operators in all parts of the State, who willingly contributed all information requested. Geological reports of the Geological Survey and the New. Mexico Bureau of Mince were drawn upon freely for information; credit to individual paper, is given in the text.

Jan 1, 1938

By G. Apsey

Eutectic freeze crystallization (EFC) is a novel technique for the recovery of pure salt and pure water from hypersaline waste brines. It is therefore a promising technology for the treatment of industrial waste waters. The impurities caused by crystallizing salt out of multi-component brines by EFC have not yet been investigated, however. To these ends, the selenium impurity found in sodium sulphate, produced from the waste brine of a platinum operation, was investigated. It was believed that the similarity between sulphate and selenate ions allowed isomorphous substitution of selenate ions into the sodium sulphate crystals, which was the likely cause of impurity uptake. It was found that the presence of sodium chloride in the industrial brine promotes the uptake of selenium, while ionic strength of the brine and mass deposition rate of sodium sulphate did not have a significant effect on the selenium uptake. Isomorphous substitution is predicted to be the most significant mechanism by which all impurities will be taken up when applying EFC to other industrial waste brines.

Jan 1, 2013

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970

By N. Hiroyoshi, R. D. Corpuz, M. Ito, Hokkaido University, C. B. Tabelin, S. Veerawattananun

"Acid mine drainage (AMD), the very acidic and heavy metal-contaminated leachate generated when pyrite-bearing rocks are exposed to surface oxidizing conditions, is a serious environmental problem encountered after the closure of mines and mineral processing operations. In this study, we investigated the effects of soluble phases and metallic oxides, which are commonly found in strongly weathered pyritic wastes, on pyrite oxidation. Strongly weathered pyrite containing melanterite (FeSO4·7H2O) as the main soluble phase was obtained from Furikusa mine, Japan. The sample was washed using two methods to vary the relative amounts of melanterite in the sample. The effect of metallic oxides on pyrite oxidation was evaluated using ultrapure hematite suspensions. Our results showed that under acidic conditions, the effect of soluble salts on the oxidation of pyrite was stronger than hematite. More thorough washing of the sample resulted in the formation of an arsenic-bearing iron-oxyhydroxysulfate coating that minimized pyrite dissolution. This oxidized layer became relatively thicker and mechanically stronger when hematite was introduced after the more thorough removal of soluble salts. Characterization of this “coating” coupled with geochemical modeling suggest that it is most probably composed of two materials: schwertmannite and scorodite. Based on these results, a new approach to suppress pyrite oxidation by directly using iron-oxyhydroxysulfate as coating material is introduced.INTRODUCTION Acid mine drainage (AMD), the very acidic and heavy metals-contaminated leachate produced in closed/abandoned mine sites (Evangelou, 1995), mineral processing and coal cleaning tailings (Evangelou, 1995), and tunnel construction waste rocks (Tabelin and Igarashi, 2009, Tabelin et al., 2012), is one of the oldest and probably the most serious environmental problem of anthropogenic origin. When released to the environment, it rapidly pollutes river, soil and groundwater systems leading to the destruction of affected ecosystems. AMD is produced when pyrite (FeS2), one of the primary gangue minerals in sulfide ores and coals, is exposed to oxidizing conditions as illustrated by the following reactions:"

Jan 1, 2016

By Bruce Vandenberg, R. Frank Chiappetta, John Foley

Recent advances in solid-state, field portable, fast framing compact video camera systems and PC based frame capture hardware now allow blast imaging up to 1000 frames per second. Up to 4.1 seconds of data can be captured directly into the unit, downloaded to a PC or archived to a standard VCR without data compression. Since no film processing is involved, motion analysis can be performed instantly and on-site within a few minutes. This paper will describe the design features and applications of the MotionMeter system and compare these with the analogous aspects of film-based cameras and other systems. Of all blast monitoring systems and techniques available today, high-speed motion picture photography and videography still remain as the most valuable, stand alone, diagnostic techniques for troubleshooting and evaluating full scale blasts in the mining and explosives industries. High-speed image data, coupled with information obtained from other instrumentation systems, such as continuous velocity of detonation recorders, laser surveying systems, refraction and ground vibration recording seismographs, etc., can eliminate many assumptions about what actually took place in a blast. Thus, diagnostic confidence in evaluating both excellent and poorly designed blasts is increased, and optimum blast results, (which are application dependent), are achieved considerably faster when compared to the trial and error approach of relying on strictly the experience factor. Applications include developing site-specific blast designs, decay equations relating burden, burden velocity and explosive energy, determining ground response times, reducing coal damage, quantifying backbreak, evaluating the effectiveness of sternming, checking delay detonator firing times, evaluating air decks and for studying general dynamics. Motion analysis is performed with a 2D and 3D software package developed specifically for video analysis, but is also directly applicable to film analysis when using a digitizer. Dimensional controls, lens aberration, field set-ups and camera orientation are all automatically corrected for with matrix analysis.

Jan 1, 2000

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

Thallous chloride and cadmium metal were recovered from a thallium-cadmium concentrate by a method suited to the treatment of small batches. Differences in oxide solubility and control of pH were employed to separate the thallium and cadmium. The cadmium metal produced by zinc reduction analysed better than 99.95 per cent Cd and thallous chloride of high purity was precipitated from solution.

Jan 1, 1969