Search Documents

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950

By O. Noirot, H. C. Owens, P. D. Rao, D. E. Walsh, J. R. Mokka

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10- 20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C range.

Feb 24, 1997

By Germán Rodolfo Ocampo Castillo

El presente texto señala la incrementación de la productividad de la mina Xstrata Tintaya -Antapaccay a través del contrato de personal adicional, donde se reemplace a los operadores titulares durante la hora de refrigerio y asi mantener una operación contínua en la mina. Como consecuencia de ello, se incrementará la cantidad del mineral descubierto en la mina y por ende, el costo unitario de las libras de cobre adicional por operación contínua se reduce.

Sep 12, 2011

By M. A. Trvits, M. Cummins, A. C. Smith, T. P. Mucho

This paper evaluates the effectiveness of remotely applied nitrogen-enhanced foam to aid in efforts to isolate and suppress a mine fire. The foam, in combination with a remotely-installed cementitious mine seal and a novel borehole pressure sampling methodology to determine the location of the suspected ignition source, was used to help control ventilation and inert the area surrounding the suspected ignition source by isolating it from oxygen. This allowed mine rescue teams to safely enter the mine, seal the area, and begin recovery operations to successfully return the mine to full production.

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

Certain information contained herein regarding Champion Minerals Inc., including management?s assessment of future plans and operations, may constitute forward-looking statements under applicable securities law and necessarily involve risks, including but not limited to risks associated with mining exploration, operating costs, production costs, volatility of share prices, currency fluctuations, imprecision of resource and reserve estimates, environmental risks and ability to access sufficient capital from internal and external sources. As a consequence, actual results may differ materially from those anticipated in any forward looking statements. Plans, intentions or expectations disclosed in any forward-looking statements or information should not be read as guarantees of future results or events, and will not necessarily be accurate indications of whether or when or by which such results or events will be achieved. Except as required by law, Champion Minerals Inc., expressly disclaims any intention and undertakes no obligation to update any forward looking statements or information as conditions change. The historical mineral resources mentioned are strictly historical in nature and are non-compliant to National Instrument 43-101 mineral resources and mineral reserves standards, and should therefore not be relied upon. A qualified person has not done sufficient work to upgrade or classify the historical mineral resources as current National Instrument NI-43-101 compliant.

May 1, 2011

By EDGAR K. SOPER, Clarence A. Wright, DOUGLAS C. LIVINGSTON, Thomas Varley

In 1917 the Federal Bureau of Mines and the University of Idaho arranged to cooperate in an investigation looking to the improvement of mining and milling methods in the mining districts of the State of Idaho, with an especial view to the wider development of the minerul deposits and greater efficiency in the treatment of the lowgrade ores of the State. This work has been made possible lnrgely through the generosity and active assistance of the mine operators, especially certain companies in the Coeur d'Alene region. As the first step in the work under the cooperative agreement it wa.s decided to gather all data possible on the various mining districts throughout the State, both active and abandoned, in order to ascertain their potential possibilities, especial attention being paid to methods of metallurgical treatment and to the solution of the many metallurgical problems in order to effect a greater commercinl saving. With this plan in view, field work was begun in the latter part of May, 1917, and was continued during the summer. E. K. Soper, formerly professor of mining, University of Idaho, and now dean of the mining department of Oregon Agricultural • College, Corvallis, Oreg., visited the mining districts in central and southwestern Idaho and also some of those in the northern part of the St.ate. D. C. Livingston, professor of geology at the University of Idaho, Moscow, Idaho, also visited some of the mining districts in central Idaho during the summer; in addition, much valuable information he had gathered on former trips to many other districts is included in this report. Credit is also due Mr. Livingston for the maps covering the State, as well as the bibliography nt the end of each chapter. Thomas Varley, superintendent of the Seattle mining experiment station of the Bureau of Mines, spent a short time in the field, principally in the mining districts in central and . northern Idaho, and made a brief visit to the southwestern districts with Mr Soper. The field work of Mr. C. A. Wright, metallurgical engineer of the Bureau of Mines, in direct charge of the cooperative work, was chiefly in the Coeur d'Alene region. Mr. Wright visited nearly all of the mining districts in the region and devoted most of his time to studying the milling methods. The results of the investigation are set 1iorth in this bulletin. The bulletin aims to give the l9Calities of the various mining districts, and the nature of the present operations and those that have been carried on in the past. The geology is discussed only in a general way, the descriptions being intended more especially to bring out the types of ore deposits and the character of the ores, a knowledge of which is essential in determining the proper treatment of the ores. The writers do not wish to imply that all districts mentioned in this bulletin were visited during the summer of 1917, for a great deal of the material has been gathered from other reports, especially from publications of the United States Geological Survey. However, it is hoped that this report will be of help to those who are interested in mining in the State of Idaho. The plan is to continue the field work and subsequently publish the results of the investigations in much more detail, with greater emphasis given the metallurgical treatment of the ores and the problems involved.

Jan 1, 1919

By J W. Simmons, T H. Antoun

"Rock fragmentation is an important component of explosive mining and excavation techniques andis the culmination of a damage accumulation process dominated by crack propagation. During the past 20 years, improved computer modeling of this process has resulted in new and promising computational tools for improving explosive mining and excavation procedures. This paper discusses one of these new computational tools, a computer model called BFRACT."

Jan 1, 1995

By K. Robert Dorman

Spray-applied polyurethane foam was used to insulate the walls of heated rooms excavated in permafrost. The experiment was designed to determine whether polyurethane foam can be sprayed successfully on frozen ground under freezing conditions and to measure the effectiveness of the insulation in maintaining--at elevated temperatures for an extended period--a room excavated in frozen ground. Two manufacturers' foams were investigated in the laboratory. Subsequently, one of the foams was employed to insulate two small rooms, one in frozen gravel and one in frozen silt, in an experimental tunnel belonging to the U.S. Army Cold Regions Research and Engineering Laboratory (USACRREL) near Fairbanks, Alaska. Following insulation, heat was introduced into the two rooms. Heat migration across the insulating barrier into the walls, in addition to wall closures, was monitored over an 8-month period. The results show that polyurethane foam can be successfully sprayed on frozen ground in below-freezing temperatures. Given this type of insulation, together with winter cold to supercool the surrounding ground, it should be possible to maintain a shaft or heated room in permafrost for several years.

Jan 1, 1970

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

By W. H. Ryback

When a fire or explosion occurs in an underground coal mine, the atmosphere guickly becomes irrespirable. Highly irritant smoke and toxic levels of carbon monoxide and dioxide are produced, and consumption of oxygen by the fire or blast can reduce its concentration below that needed to support life. Work parties entering such a hazardous atmosphere for rescue or recovery operations are required to use, as their primary respiratory protection, a fully self-contained breathing apparatus of at least two hours duration. Apparatus used in this role has primarily been of the closed circuit rebreather type, using pressurized oxygen storage and chemical removal of expired carbon dioxide. Typically, commercial self-contained breathing devices for mine rescue have been heavy, bulky, and uncomfortable to use. The McCaa apparatus, long the industry standard, represented the best art available when it was First designed in 1926. It weighs 41 Ibs., protrudes about six inches above shoulder height, and provides breathing gas at temperatures up to 120° F. More recent designs, such as the Drager BG174A and Scott Rescue-Pak, using modern light weight materials and fabrication techniques have improved on all parameters of the McCaa to some extent. It was the intent of the Bureau of Mines, acting under the authority of the Coal Mine Health and Safety Act of 1969, to fund the development of a new self-contained breathing apparatus which would incorporate the best available technology and serve as a benchmark for future commercial designs, as the Bureau-sponsored McCaa had 45 years previously.

Jan 1, 1974

By H. B. Hill

The West Red River oil field, in Tillman County, Okla. (fig. 1), is approximately 8 miles northwest of the town of Burkburnett, Wichita County, Tex. The wells are in the river bed between the medial line and the south bank of the Red Diver. In the following discussion of the geology, development, and exploita-tion of the field, the authors have, by means of structure maps, crews sections through various parts of the reservoir and tabulated development data and production statistics, recorded salient information on a field whose development was unique and in some respects unusual for fields discovered and initially developed more than a quarter of a century ago. The total oil production from Government-operated leases; considered in the report was 6,900,440 barrels to January 1, 1947, from 3 proved acres developed by H1 oil-producing wells, 10 gas-injection wells, and 5 nonproductive wells. A calculated past recovery of 60P, barrels of oil per acre-foot and an estimated ultimate recovery of 6.S0 barrels of oil per acre-foot under present gas-injection methods begun in 1929 in shown.

Jan 1, 1949

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

By Elizabeth Cruz

The paper point out innovative energy management techniques that lead to energy recovery and uses it back in the process as heat, mechanical work or power with a consequent impact on operating cost and operating cost and operation cost and a reduction in the overall enviroment impact.

Sep 14, 2009

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By Eric Konigsmann, Doug Spence, Scott Jones

"The Williams Gold Mine is located in the Hemlo camp of Northwestern Ontario and is one of Canada’s largest gold producers with annual gold production of 400,000 ounces. The operation is owned and operated as a 50:50 joint venture between Teck Cominco Limited and Barrick Gold Corporation.In July 2002, the decision was made to introduce paste backfill produced from mill tailings as the primary backfilling method in the mine and to decommission the existing cemented rock fill system. This required a fast track design to be completed for both a surface paste backfill plant and an underground paste distribution system followed by an intensive construction phase through the fall and winter of 2002/2003. The paste system was commissioned on schedule in late April 2003 and was in full production within 4 weeks of the initial start up. Overall, the project duration was only 42 weeks from initial project release to commissioning and it was completed $2 million under the budget of $14 million.This paper presents an overview of the lab testwork and process flowsheet design, process control methodology and describes the construction and commissioning phases of the project. Preliminary paste plant performance and operating cost data is also presented.IntroductionThe Williams Gold Mine is located in Northwestern Ontario adjacent to the Trans Canada Highway in the Hemlo Gold Camp as shown in figure 1. The mine currently produces approximately 400,000 ounces of gold annually and is owned and operated as a 50:50 joint venture between Teck Cominco and Barrick.The deposit was discovered as part of the Hemlo gold discovery in 1981 which led to the development of three mining operations within a 2 kilometre radius. The neighboring operations are the Golden Giant Mine, currently owned and operated by Newmont Gold, and the David Bell Mine, currently owned and operated by the same joint venture which is running Williams. David Bell ore is blended and milled in the Williams concentrator."

Jan 1, 2004

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009