Search Documents

In the Bendigo district, with its large number of comparitively small leases worked by separate companies, we might naturally expect to find many different arrangements of winding machinery and, as a matter of fact, there are steam winches, old portable engines, single and duplex geared engines, twin engines on the first motion, and in one instance a single engine on the first motion, all employed for hauling purposes from depths of 1000 feet and over.It would be impossible in the compass of this paper to discuss at all fully the various arrangements of winding gear employed on the field the writer can simply refer to some of the more prominent features, in the hope that the information may prove of interest and benefit to the mining community. In criticising our machinery it must be remembered that when many of the plants in use at the present time were erected, they were not intended to wind from more than one third of the depths now common on the field; but so long as the machine could be made to haul a tank of water from the bottom of the shaft it has remained, the greater power required being obtained by increasing the piston speed and altering the gear wheels to suit. The consequence is, of course, that in some of our mines the speed of winding is painfully slow this feature, however, though certainly not consistent with modern ideas of economical mining, does not so seriously affect Bendigo as it would other fields, for the comparatively small quantity of stone to be raised from a given reef by some...

Jan 1, 1902

By D. Harrington, M. W. Von Bernewitz

"Introduction In studying the mine disaster files of the Bureau of Mires for preparation of a bulletin on coal-mine explosions, a table was compiled covering various features of fan installations and the handling of air currents at the time of and after the disasters. As a sidelight on this discussion, there was tabulated the loss of life and number of men injured.Discussion of collected dataOf the 164 disasters tabulated, 148 were explosions, 14 were fires, and 2 involved both fire and explosion. The total loss of life was 4,158 and 412 were injured. There were 145 disasters in bituminous coal mines, 13 in anthratice mines, 2 in lignite mines, 1 in a cannel coal nine, and 3 in metal mines. By States, 35 took place in Pennsylvania; 17 in West Virginia; 16 in Oklahoma and Alabama; 15 in. Kansas and Illinois; 12 in Indiana; 7 in Colorado; 6 in Kentucky; 3 each in Ohio Tennessee and Wyoming; 2 each in Arkansas, Montana, Washington, Virginia, New Mexico and Utah and 1 each in Iowa, Missouri, Maryland, and California."

Sep 1, 1924

By W. H. Schiffbauer

The protection of miners, equipment, and infrastructure is discussed. While the primary focus of the described technology is to prevent miners from being injured, struck-by, or crushed by heavy equipment; another major benefit realized is also the protection of equipment and infrastructure. An attempt is made to define and classify the systems used to provide proximity detection and warnings as well as collision detection and avoidance. Information about the speed of vehicles and human operator response time can be a factor in the choice of what type of system and what features are needed to properly address the needs. How the technology adjusts to compensate for various vehicle speeds, while maintaining the same level of protection is noted. The statistics which justify the need of miner protection are provided. The primary system components required, what attributes they feature, and how they respond in the environment, is briefly highlighted. The physics behind the danger zone marker technology and what makes it so robust and reliable is established. Examples of a few mining applications and specific operational modes are provided for both surface and underground.

Jan 1, 2011

Two outstanding features of the world's young orogenic belts are their very consistently developed suites of volcanic rocks and, it is now recognized, the rather distinctive types of mineralization they contain. Further,it is now known that these volcanic suites exhibit evolutionary patterns, and it is beginning to appear that this evolution in style of igneous activity is accompanied by a parallel evolution in style of mineralization. Specifically,podiform chromite and stratiform pyritic copper ores of Alpine ultramafic/submarine tholeiite association progressively give way to more zincian stratiform ores associated with andesites and dacites, "porphyry copper"deposits developed in quartz dioritic to dacitic plugs, and lead-zinc stratiform ores related to increasingly pyroclastic, rbyodacitic volcanism.This "coupling" is exhibited well in the volcanic arcs - the young orogenic zones-of the SW Pacific which, with tbeir abundance of youthful and commonly unmetamorphosed materials provide an opportunity for investigating, through a petrochemical approach, the possible significance of ores in the elucidation of mechanisms of lava formation. It is suggested as a working hypothesis that in the orogenic (voleanic arc) regime ores are associated with the cale-alkaline rocks because these cale-alkaline rocks are in part generated by exhalative loss, and the ores are among the manifestations of tbat loss.

Jan 1, 1978

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

When Haematite Explorations Pty. Ltd. began prospecting for petroleum in 1960, there was only ill-defined geological evidence on the land bordering Bass Strait to support the belief that petroleum lay trapped in sedimentary formations beneath its shallow waters.A reconnaissance of the area, made in 1961 by the airborne magnetometer method, covered the waters and islands of the Strait and overlapped the Victorian and Tasmanian coasts. The survey indicated the presence of the Bass Basin (which is completely water-covered), assisted in outlining the Otway and Gippsland Basins, and showed that each basin contains sedimentary rocks over 10,000 ft thick. Information on the regional geology and minor volcanic activity was also obtained.Marine seismic surveys carried out from 1962 to 1965 defined these basins more accurately and showed the nature and structure of the thick sedimentary sections.Correlation of the seismic data with onshore wells identified the sediments as Tertiary and Mesozoic. Subdivisions of the former in all basins and the latter in the Otway Basin were made. These Tertiary and Mesozoic rocks are not seriously deformed and they have good prospects of containing petroleum.Possible structural and stratigraphic traps, recognized from the seismic record sections by petroleum geologists, are being tested by offshore drilling which began in 1964.

Jan 1, 1966

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By D. M. A. Flight, G. E. M Hall, P. R. Simpson

theoretical viewpoints.

Apr 1, 1994

Determination of Flotation Kinetics of Coal Grain Types in a Pilot Scale Jameson Cell using Coal Grain Analysis Method

Sep 13, 2010

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

The labour question is one that has caused mine managers much thought and anxiety and is likely to continue to do so as long as human beings exist. The difficulty is to devise some arrangement whereby the interests of miner and mine ownerare identical. Mines cannot be worked without capital, and capital is no good without labour, yet, though both have the mine in common, their interests are not exactly the same. Some men are happy so long as they can scrape through by exerting themselves as little as possible, but capitalists do not work mines for charity, they want some return for their money.Where a large number of men are employed there are bound to be examples of all sorts, good and bad, and it is because one cannot depend on all, that different methods of employment have to be adopted. Which method is selected depends to a great extent on the labour market, local conditions, nature of the ore and the way in which it occurs.A big step towards success is obtained by securing the services of good bosses, not only those who know how work should be done, but men who have a knowledge of human nature. It is a big mistake to be too lenient with a man, also to be unnecessarily harsh. A good boss will always be sought out by good men who have worked under him before, or who have heard of him from others. By a good boss we do not mean one who employs two men where one would do, or who lets the men loaf...

Jan 1, 1901

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By Edmond Chin

The land mass of the Asia and Pacific region comprises 11 million square miles or about 15% of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest island or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The countries in the Asia and Pacific region represent some of the most vibrant economies in the world. Japan is undisputed as one of the world's leaders in manufacturing and commerce. Hong Kong and Singapore are significant both as entrepôt and banking centers. The economies of Australia, the Republic of Korea, and Taiwan compare favorably to the level of the industrialized countries in western Europe. Indonesia, Malaysia, the Philippines, and Thailand have maintained strong economic growth during the past two decades. All these countries in the Asia and Pacific region collectively constitute a significant bloc as to raw materials production and consumption, as to manufacturing, and as to world trade.

Jan 1, 1992

In its April 1991 issue, MINING ENGINEERING published a salary survey form asking for information relating to engineering and management jobs in the minerals industry. 1038 of these forms were filled out and returned, most of them being received in the magazine's offices at SME headquarters before the end of June 1991. An SME volunteer took on the task of tabulating and analyzing data from the forms, but the press of other business interfered with this work, and publication has been delayed until this issue of MINING ENGINEERING. Appreciation is extended to SME members who took the time to fill out and return the salary survey forms, and our apologies go to MINING ENGINEERING'S readers for the delay in publication. Of the total number of forms received, more than 97% were from SME members. The geographic distribution of the respondents closely mirrored that of SME membership as a whole, about 50% being from the Society's Western Region, 19% from the Central Region, and 23% from the Eastern Region. About 8% were from outside the US. Average salaries for each of the four geographic areas ranged between $55,000 and $60,000, with the highest average in Eastern Region (Fig. 1). Respondents were asked to answer a number of questions formulated to determine if there are significant differences in salaries based on the type of organization for which they work. As indicated by Table 1, salary averages at mining companies do not vary markedly with the size of the company: • Large companies, defined as those having more than $1 billion in annual sales, accounted for just over 16% of the returns. Their average salary was $61,840 per year.

Jan 1, 1992

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

To meet the energy requirements, hydroelectric projects are planned and executed in many countries. Though these projects requires a high capital investment, the returns are regular with minimum maintenance after commissioning of the project and are ecofriendly. Bhutan is situated in the eastern Himalayas and covers an area of 38,394km2 (14824.01sq. miles. It is bordered by India in East, South and West and by Tibet in the North. The hydropower potential of the country is estimated at 30,000MW, out of which around 5% has been harnessed.

Jan 1, 2016

By L-B Fu and J Tan, J H. Wei, N Tian

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kendenggaoer-Kuokuqueke region lies in the western part of Chinese North-western Tianshan. New laser ablation inductively coupled plasma mass spectrometry zircon U-Pb geochronology for five separate granitic plutons for this region reveal two distinct intrusive periods: late Devonian (367~361 Ma) and late Carboniferous (315~301 Ma). These intrusions all share an arc-like geochemical affinity (ie enrichment of large ion lithosphere elements and negative anomalies of Nb, Ta and Ti). In situ zircon Hf isotopic compositions further differentiate the magmatic cycle, with the late Devonian intrusions yielding more depleted eHf(t) (+1.47~+6.54) composition than the late Carboniferous intrusions (eHf(t) = +4.95~+9.79). These geochemical data suggest that they might be mainly derived from different source regions and the tectonic setting was transformed into post-collisional in the late Carboniferous. As in many significant porphyry-ore districts, this dramatic tectonic reconfiguration, combined with melting of an evolved crust, resulted in genesis of metal-bearing melts. Furthermore, we can show that Neoproterozoic mafic juvenile lower crust intruded by mantle-derived melts and/or partial melting of slab material generated hybrid primary magma during subduction of the Palaeo-Junggar oceanic crust in the late Devonian. Whereas underplating of mantle-derived magma contributed more to the Late Carboniferous post-collisional magmatism.CITATION:Tian, N, Wei, J H, Fu, L-B and Tan, J, 2015. Timing and geodynamic setting of the late Palaeozoic polymetallic mineralisation in Chinese north-western Tianshan – insights from geochronology and petrogenesis of granitoids , in Proceedings PACRIM 2015 Congress, pp 171–174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015