Search Documents

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By Charles Will Wright

This paper is one of a series dealing with mining problems and summarizing the data contained in the Information Circulars on individual mines that have been prepared by the managers or superintendents and published by the Bureau of Mines. The purpose of this paper is to present the problems encountered in the development of an efficient mine organization and to show the means used by certain mining companies in promoting efficiency. There is also a discussion of the advantages and disadvantages of the various systems of paying and handling labor and a description of their application at the individual mines.

Jan 1, 1932

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

By Michael A. Piepenburg

The East Side Access (ESA) Project will extend Long Island Rail Road (LIRR) into midtown Manhattan via 11 km of tunnels, a new terminal station and associated support facilities. In addition to the hard-rock tunneling currently underway in Manhattan, soft-ground tunnels in Queens will traverse beneath Amtrak?s Sunnyside Yard and Harold Interlocking, the busiest rail interlocking in North America. This paper details ESA?s coordinated approach to interfacing with both Amtrak and LIRR with regard to the planned tunnels, shafts and related construction beneath or adjacent to the operating railroads. This interface includes integration of railroad staff, extensive presentations, reviews and agreements with the railroads regarding settlement mitigation, real-time automated geo-instrumentation monitoring, ground improvement, and geotechnical/environmental controls.

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

R. C. BUCKETT (Lake View and Star Limited) : At the outset I should like to add my congratulations to those already extended to Mr..Norwood on his excellent paper, which has given us all an inspiration to strive further to improve our plant recoveries. In some respects this paper has left us so little to discuss without considerable time spent on. further research work. At all points one is met by a baffling array of facts which leave one feeling hesitant to speak.The careful and methodical way in which Mr. Norwood went along step by step until all channels of research presenting themselves were tested to his own satisfaction leaves me with but a few comments to make. Particularly striking to me is the explanation of the residual gold values in calcines by recrystallization of haematite and here is a line to be attacked by future studies. This will be mentioned again later.Particularizing on the paper, the first point that struck me was the method of change of pyrite through to the final haematite. I have never been able to satisfy myself that a sample taken from various positions along a roaster when cooled, as described on p. 397, represented a fair sample of the conditions at that point, but I must confess that I have not found a substitute that did satisfy me.However, the following figures are illuminating... But to fill dry a receptacle of known volume with calcines, as described by Mr. Norwood, gives the following apparentspecific gravities:

Jan 1, 1940

By D M. Aranha, M A. Fonseca, M Echtern

The regional syndeformational metamorphism affecting the Itabira Iron Formation (IIF) at Quadrilßtero Ferrffero (QF) was formerly discussed by Dorr (1965), who proposed that quartz grain size could monitor the metamorphism, according to James (1955), and that the formation of haematite could be the result of the synchronous metasomatic process. Herz (1979) suggested the existence of three metamorphic zones, not mentioning the haematite formation. It could be observed that the primary oxide phase in the IIF is magnetite and most of the hard haematite was derived from the metamorphic replacement of magnetite, forming micaceous or schistose haematite. Differently from most iron formations in the world, the formation of haematite deposits at QF occurred under high oxygen fugacity during metamorphism. The haematite microlaths display a strong preferred orientation, which determines the alongated shapes of the fragments. The terms foliated and unfoliated haematite have been applied by Dorr to the micaceous or schistose haematite, and to the isotropic, hydrothermally derived haematite. Under the microcope, the haematite exhibits a strong crystallographic or lattice orientation encircling the magnetite and martite porphyroclasts. The strain rate determined and defined the textural variation, size and economic importance of the deposits and the ore grade. Metamorphism at QF increases eastward and resulted in the formation of a gruneritic Fe-Mg amphibole, at the western portion, followed by a cummingtonitic amphibole at the central-western part, succeeded by the actinolite zone at the central-eastern part, and finally to the tremolite-anthophyllite zone to the east. These zones, arranged in a north-south pattern, can be followed in the pelitic units, whereas appear sericite-chlorite, kyanite-chloritoid and garnet-staurolite respectively. Carbonate geothermometry in IIF also may support the metamorphic variations. At the western zone the haematite forms small lenses within the itabirite, P-contents are slightly higher than in the remaining IIF, haematite grain size is minute, resulting in a submicaceous texture and the amount and dimension of relict magnetite within haematite is greater than in the other parts of QF. Jangada and Serra Azul deposits are examples of this zone. The central-western zone is characterised by significant haematite deposits, in considerable quantity and size, haematite grain size increased, in order to produce a micaceous texture, the P-contents and the amount of magnetite decreased. Pico do Itabirito, Cappo Xavier, Capitpo do Mato and Tamanduß correspond to the deposit type of this zone. At the eastern-central portion the amount of the hard haematite deposits decreases, increasing the soft haematite ore due to higher strain rates. However, it can be perceived that the relict magnetite almost disappeared and the haematite grain size became coarser than the haematite from the western zones. At the eastern zone, the haematite deposits exhibit typical schistose texture, the magnetite porphyroclasts are absent and the lowest P-grades in the haematitic iron formation. The haematite bodies characteristic from this zone are Andrade, Morro Agudo and the deposits at the Itabira District. The hydrothermally derived compact and isotropic haematite deposits, formed subsequently to the micaceous haematite bodies, were generated after deformation ceased, but under very high fluid pressure. The metamorphic reactions magnetite + quartz + H2O = grunerite + haematite and magnetite + quartz + H2O = grunerite + O2 were decisive in the formation of the metamorphic haematite deposits.

Jan 1, 2007

By Jacek Paraszczak

L?exploitation rentable des gisements de type filonien constitue un problème important dans le contexte actuel de l?industrie minière québécoise. Les études effectuées depuis 1994 ont indiqué, que la technologie d?abattage mécanique utilisant l?outil hydraulique appelé « éclateur radial-axial » constitue une alternative intéressante par rapport aux méthodes conventionnelles par le forage et sautage. Les essais du prototype de l?éclateur ont prouvé qu?il est en mesure d?abattre les roches dures dans un environnement minier, mais sa performance dans les termes de masse du roc abattu dans une unité de temps a soulevé certaines doutes. Pour cette raison, une étude de préfaisabilité de l?éclatage en tant qu?une technologie d?excavation souterraine a été réalisée. Cet article présente quelques résultats des travaux effectués dans le cadre du contrat octroyé à l?Université Laval par le Ministère des ressources naturelles du Québec. Leur objectif principal consistait à comparer, pour les conditions des gisements filoniens, la productivité et les coûts des méthodes d?exploitation souterraine utilisant l?éclatage par rapport à celles conventionnelles. Deux variantes proposées de cette méthode ont été comparées avec la méthode conventionnelle sur le plan du coût (par tonne de minerai) et de la teneur de coupure de minerai d'or. Les études ont démontré que l?application de l?éclatage représente un potentiel de réduire ce coût, surtout dans les situations où l?abattage sélectif pourrait avoir lieu. Pour le cas de base on a trouvé, qu?il serait possible de réduire la teneur de coupure par la marge d?environ 16 ? 26%. Toutefois, les études de sensibilité ont démontré, que le coût dépend de façon important de la productivité d?éclatage, qui, pour sa part, varie beaucoup en fonction de paramètres du massif rocheux devant être abattu.

Oct 1, 2001

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites that contain mineral assemblages derived from the crystallization of post- magmatic fluids or from the metasomatic action of residual peg- matitic fluids. They have been the traditional sources of raw material for ceramic and chemical industries. With the discovery of the Searles Lake deposits, brines became new sources of lithium, and, today, two brine deposits satisfy nearly one-half of the free world demand for lithium chemicals. Indeed, lithium production from pegmatites has been superseded by brines sources. In the United States, the brines of Clayton Valley, NV, have been exploited since 1964 by Cyprus Foote Mineral Company, a subsidiary of Cyprus Minerals Company. In Chile, Sociedad Chilena de Litio Ltda., an affiliate of Cyprus Minerals Company, is now producing lithium carbonate from the brines of the Salar de Atacama. Recently identified brine deposits suggest that these may well become the prime sources of lithium chemicals. In Bolivia, the government is negotiating the rights to exploit the brines of the Salar de Uyuni. The Salar del Hombre Muerto in Argentina is being evaluated as a future center of chemical production. The brines of the Great Salt Lake of Utah, the Smackover Formation, and the Imperial Valley geothermal field have been defined as important resources of lithium. In Tibet, high concentrations of lithium have been reported in several saline lakes. In the People's Republic of China, lithium may be produced from the brines of the Dabusan playa in the Qinghai Basin. The 1950s saw a great number of lithium companies develop. However, following the termination of the Atomic Energy Commission purchase program in 1959, several companies, such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp., were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminumpotlines), the lithium industry grew steadily. With the potential application of lithium metal in batteries, nuclear reactors, and fuel cells, a steady growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Presently identified reserves and production capacity are sufficient to satisfy the conventional market growth of lithium.

Jan 1, 1994

By Barbara H. Scott Smith

"During the last two decades lamproites have joined kimberlites as the only two known primary sources of economic quantities of diamonds. This paper contrasts the petrography, primary and xenocrystic mineralogy and pipe geology of these petrogenetically separate rock types. The petrographic discrimination of kimberlites and lamproites from each other, as well as other rock types found during diamond prospecting, is discussed. Kimberlites and lamproites can be classified texturally and mineralogically. Such classifications highlight the differences between, and among, lamproites and kimberlites. The implications of these differences for diamond exploration programs are discussed, with particular emphasis on the application of petrography. IntroductionKimberlite was the term coined in the late 19th century to describe the host rock of diamond at the type locality, Kimberley, South Africa (Lewis, 1887, 1888). Innumerable kimberlites are now known worldwide; some of them contain economic quantities of diamond (e.g. South Africa, Botswana and Russia) while many are barren. Jennings (1989) suggests that less than 3% of the known kimberlites can be considered to be commercial. Kimberlite was thought to be the only important primary source of diamond for approximately a century. Until the late 1970s, lamproites were thought to be only academic curiosities. Some workers (e.g. Wade and Prider, 1940), however, did comment on certain similarities between lamproites and kimberlites and, hence, inferred a potential for lamproites to carry diamonds.The term lamproite was introduced by Niggli (1923) for leucite-bearing rocks from southeast Spain and Wyoming which had some unusual geochemical characteristics. Wade and Prider (1940) used the term lamproite (as defined by Troger, 1935) to embrace rock types found in the West Kimberley area of Western Australia. All the lamproites described by Wade and Prider (1940) form distinct topographic features. Subsequently in the late 1970s, additional pipes, which have little or no relief, were discovered in the same area, but only as the result of a major diamond exploration program (Atkinson et al., 1984; Jaques et al., 1984, 1986). Some of these bodies are diamondiferous. In 1979, the Argyle pipe was discovered in the East Kimberley area which, in terms of grade, is the richest known primary diamond deposit in the world with some parts of the body having grades greater than 500 carats/100 tonnes (Madigan, 1983; Boxer et al., 1989). All the initial new discoveries in Western Australia resulted from classic stream sampling for ""kimberlite indicator minerals"" (Atkinson, 1989)."

Jan 1, 1992

By R. M. Santmyers

Thorium and cerium are two of the group of elements known as "rare earth metals," and are obtained from the mineral monazite. Previous to the employment of thorium and cerium in incandescent gas mantles these elements were nothing more than laboratory curiosities, as the rest of the rare-earth metals are to-day. The most important salts of these rare earths are the nitrates. In the manufacture of gas mantles, thorium nitrate is the principal ingredient and forms prom 92 to 99 per cent of the impregnating material; the other 1 or 2 per cent is largely cerium nitrate and is quite as necessary, for without it there would be little luminosity to the mantle when in use. When the mantle is "burned off," the nitrates are changed to oxides. The monazite used as a source of thoria contains from 6 to 9 per cent of thorium oxide (Th02) and 24 to 32 per cent of cerium oxide (Ce203). As only the thoria and a very small hart of the ceria from the monazite could be used in gas-mantle manufacture, for a time the residues consisting mostly of ceria with somewhat smaller quantities of other rare earths found no commercial application. Later, however, they came to be utilized in several ways, the most important being: (1) the manufacture of cored flaming arc carbons, a great, irmprovement over the plain arc carbons used in electric lighting; (2) cerium metal used in the manufacture of pyrophoric or sparking alloys or "flints" for automatic pocket lighters and miners' lamps; and (3) the production of special kinds of optical and art glass.

Jan 1, 1930

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By Daniel W. H. Su

A nearly 305-m- (1,000-ft-) wide sandstone channel was projected to run through the mid panel area of a 457-m- (1,500-ft-) wide longwall panel in a southwestern Pennsylvania coal mine. This sandstone channel was known to cause serious longwallface roof control problems in the mine?s B-panel area in 1998 and 1999; and most recently, it induced many large face cavities and caused a substantial production delay in the preceding panel. For the two B panels mined in 1998 and 1999, hydraulic fracturing of the massive sandstone was conducted to facilitate better caving, thus relieving cantilever compressive stress at the longwall face. Vastly improved longwall face condition was observed and four weeks of mining delay due to bad roof conditions were eliminated. The implementation of the hydraulic fracturing technique, results of underground observation and measurement, and results of numerical modeling were summarized in a paper presented in the 20th International Conference on Ground Control (Su et al., 2001). This article is a summary of the activities that took place during a four-month period (October 2011 through February 2012) at a Consol Energy longwall mine southwestern Pennsylvania to improve face conditions and safety of underground personnel during mining of the 457-m- (1,500-ft-) wide longwall panel. The elevated concern for safety was driven by adverse face conditions encountered while mining the preceding longwall panel. Many of the problems were attributed to a thick and massive sandstone channel. A joint task force consisting of coal operations engineering, Pennsylvania operations engineering and CNX Gas personnel was formed in August 2011, which recommended drilling four hydraulic fracturing holes along the center axis of the sandstone channel to reduce pressure and improve face conditions at the longwall face. To further provide detailed monitoring of the longwall face and to evaluate the effectiveness of the hydraulic fracturing program, the Longwall Visual Analysis (LVA) software (Hoyer, 2011) was installed in early December 2011 to track the face pressure and c

Jun 1, 2013

Statistics is essentially a study of variability, the use of some suitable mathematical model representative of such variability, and the application of this inferred pattern of behaviour to practical problems. Probability theory is the mathematical structure devised for providing models for chance happenings. Perhaps the simplest example of a chance happening is the result obtained in tossing a coin. Although the result of a single toss can never be predicted with certainty, there is no reason why in repeated tosses the expectancy of heads and tails should not be equal. In such a case the outcomes of the experiment are said to be equally likely, so that the probability of obtaining heads (or tails) is 1 in 2, that is, 0,5. This simple probability .model refers to a 'mathematical' or 'unbiased' coin. Whether such probabilities are meaningful for actual coins tossed in any particular way is a matter for experience to determine. Probability models have also provided the basis for representing observed variability in cases where the actual under- lying probabilities are only partly known or defy analysis. A typical example of the latter case is the variability observed in the values obtained from gold or other ore samples. The interacting natural forces which gave rise to this variability are obviously very complex and are unlikely ever to be unravelled completely. In spite of this, probability theory and the more recent geostatistical theories have provided us with models which can represent this variability on a reasonable basis. Applied statistics and geostatistics must therefore never be accepted as exact mathematical sciences. Furthermore, a basic and essential concept is that in the type of applications covered in these notes, no model must ever be accepted as necessarily the final and exact answer to the problem; thus, any model must prove and continue to prove its appropriateness in practice, preferably by follow-up comparisons.

Jan 1, 1981

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002