Search Documents

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Guilherme Vitor de Araujo, Igor Cuzzuol dos Santos, Loyslene Rabelo Fernandes, Gustavo Henrique Sousa, Athos Fernandes Araujo

O desenvolvimento de nanopartículas magnéticas vem recebendo bastante atenção de pesquisadores devido a sua potencial aplicação em diferentes campos tecnológicos, principalmente em microeletrônica e medicina. A magnetita nanoparticulada é particularmente atraente para estas finalidades, pois apresenta comportamento superparamagnético, biocompatibilidade e resistencia à oxidação. Neste estudo foi avaliado a síntese das nanopartículas pela coprecipitação. Para isso foi observado a influência da razão molar de Fe+2/Fe+3 e da variação de concentração de NaOH na nucleação e precipitação das partículas. Sendo possível, determinar os melhores parâmetros para obtenção das mesmas e garantindo as suas propriedades. Para a constatação estrutural, a caracterização das amostras foi realizada por difração de raios X (DRX). A razão molar de Fe+2/Fe+3 se mostrou uma variável importante, em razões muito pequenas o resultado obtido foi goetita, enquanto a síntese a partir da razão 0,5 observou-se apenas a magnetita. E a variação da concentração de OH- teve influência no tamanho das partículas nucleadas, no qual menores partículas foram obtidas em meios mais básicos.

Oct 6, 2019

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Wolfgang Oberaigner

Primetals Technologies has always been a driver of innovation in steelmaking, especially by providing sophisticated process expert models for continuous casting machines. This capability is demonstrated by recent advancements in automation solutions that include: DynaPhase, Dynacs 3D, and DynaGap. This state-of-the-art suite of dynamic secondary cooling and soft-reduction packages take into account thermodynamic effects such as shrinkage and phase transitions, and thereby significantly contribute to direct quality improvements during the solidification phase in the continuous casting process. Speed Expert calculates an optimum casting speed for every casting situation, and additionally recommends a strand speed so that the point of final solidification is positioned at the end of a segment for optimum soft reduction. In the case of steel grade changes, the Intermix Expert precisely calculates the chemical properties of the mixed steel, thereby minimizing losses due to deviations from required specifications. The Nozzle Expert is a new model that detects clogged nozzles and broken hoses in secondary cooling systems. The first installations were highly successful and customers are pleased with impressive reductions in maintenance costs and improved steel quality. This paper describes these innovative process automation solutions and gives an overview about the successful results achieved within the first installations.

Aug 16, 2017

By Zou Zhongpping

Under the new normal state, blast furnace outputneeds to be adapted to the market demand, however the limitation in blast furnace output has significant impact on blast furnace operation and is prone to cause inactive furnace hearth and higher fuel ratio. To address such problems, some practices to maintain stable and smooth operation of blast furnace in case of output limitation are proposed based on data analysis philosophy, which allows the blast flow and hence the top pressure to be determined based on the hot metal output, and adequate kinetic energy of blast supply can be assured by adjusting the tuyeres. Matching between the oxygen enrichment and the pulverized coal injection is also proposed based on theoretical flametemperature, and burden distribution cycle calculation method is proposed, whichoffersnew approach for analyzing the change in burden distribution pattern.

Oct 30, 2017

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Gerhard Richter, Norbert Asamer, Gerwald Decker

At various stages during their manufacturing processes - from casting to finishing before delivery - semi-finished steel and special alloy products must be cut and surface-treated as well. The requirements for the individual conditioning steps, however, can be quite different. For example, the work piece can be hot, warm or cold. At any rate, the product must always be perfectly prepared for the next manufacturing step - reliably, in the shortest-possible time and at the lowest-possible cost. For cutting and grinding, BRAUN has developed innovative technologies and highly flexible, tailor-made solutions which meet these requirements in the most optimal way. In particular, BRAUN’s cutting and grinding technologies can also be used for large-scale products.

Oct 1, 2019

By Vagner Machado Costa

O presente trabalho tem por objetivo analisar parafusos Classe 8.8 produzidos por 4 fabricantes nacionais. Para tanto, realizou-se caracterização mecânico-metalúrgica, baseando se nas normas ABNT NBR ISO 724: 2004 [3] e DIN EN ISO 898-1: 1999 [2]. O estudo de caracterização mecânica consistiu na realização de perfis de microdureza, ensaio de tração, MEV da superfície fraturada e medição dos perfis dos parafusos. A caracterização metalúrgica seguiu através de análise química e caracterização metalográfica (macrografias e micrografias). Está caracterização é de fundamental importância para verificar as variabilidades devido aos diferentes fabricantes as quais este componente está sujeito e compreender como elas podem vir a influenciar no desempenho deste produto.

Aug 16, 2017

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Bruno Cordeiro Costa

Inseridas em um mercado extremamente competitivo, as empresas siderúrgicas vêm buscando aprimorar seus processos produtivos e de gestão de forma a reduzir custos de produção e garantir sua sustentabilidade. A principal parcela do custo de produção da empresa em relação a um aço inoxidável ligado ao Cromo e Níquel está na Aciaria, e a carga metálica representa mais de 80% deste valor. Visando aumentar a competitividade, foi aberto um projeto para otimizar a carga metálica na Aciaria. A redução da mistura de escórias é uma fase deste projeto. O propósito do presente trabalho é mostrar a metodologia adotada para otimizar o processo de recuperação de sucata das escórias de aços inoxidáveis, minimizando a ocorrência de misturas de escórias, para maximizar seus teores de Ni e Cr e, consequentemente, reduzir o uso de fontes mais nobres e caras destes elementos. Foi adotada a filosofia “Zero de Escória no Chão” e, para alcançar este objetivo, várias ações foram implantadas. Considerando 2011 como base 100%, o teor médio de Ni da sucata recuperada de 3XX aumentou 45% em 2013 e o teor médio de Cr subiu 36% na sucata recuperada neste mesmo período. Como consequência direta da redução da mistura de escórias de grupos de aços diferentes ao longo de todo fluxo produtivo, ocorre a redução dos residuais de Ni e Cr nos aços carbono e elétricos e de Ni nos aços 4XX. A metodologia adotada foi eficiente e os objetivos do projeto foram alcançados.

Jul 30, 2018

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Kurt Herzog

State-of-the-art automation information technology and connectivity enables the digitalization of steel production that goes far beyond conventional automation of industrial production. Initiatives have been started around the globe to foster digitalization like IIoT (Industrial Internet of Things) in the US, Industrie 4.0 in Germany or China 2025. Primetals Technologies is actively driving the digitalization shaping the future of steel production. Intelligent combination of sensor technology combined with digital models as well as quality and production planning and control systems leads to new dimensions in product quality and production cost reduction. New diagnostic ways allow intuitive fault tracing or processing to support faster maintenance. Digital assistants support both operation and maintenance using context-oriented or self-learned information.

Oct 30, 2017

By Wagner Fidelis Brum

Os desafios atuais no mercado de mineração de ferro requerem uma gestão de engenharia cada vez mais dinâmica a fim de tornar viáveis novos projetos, os quais contemplam reservas com minérios mais profundos, mais compactos e com teores menores do metal alvo. Além disso, estudos de viabilidade de alta complexidade têm como objetivo tornar rentáveis operações inseridas em ambientes repletos de restrições. Neste trabalho serão discorridas diferentes formas de se estruturar a engenharia a fim de atender tanto a projetos pequenos, quanto médios ou grandes. Nesse momento serão abordadas vantagens e desvantagens de cada modelo, bem como serão sugeridas estruturas para que se atinja uma boa qualidade de engenharia dentro do custo esperado.

Aug 1, 2018

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019