Search Documents

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Martin Chabicovsky, Milan Hnizdil

Emulsions are frequently used for the cooling and lubrication of working rolls during the cold rolling. The fact that the lubrication and cooling are not separable makes the optimization of both functionalities difficult. The higher emulsion temperature decreases the cooling efficiency compared to cold water. Heat transfer and fluid flow laboratory (Czech Republic), CRM (Belgium), Tata steel (Netherlands) and Henkel (Germany) cooperated on the increasing of a cooling efficiency during cold rolling. Part of this research was focused on an influence of the emulsion composition on a cooling intensity. The cooling efficiency was laboratory investigated. The stainless steel sample with thermocouple was heated and then it was cooled by a nozzle. Tests were performed with various emulsions and pure water. The heat transfer coefficient was computed from measured temperatures. The cooling intensity (heat transfer coefficient) of all tested emulsions was similar but an increase of the cooling intensity was found with water. Further various emulsions concentrations were tested. Results showed decreasing cooling intensity with increasing oil concentration. Adding additives therefore is thought to cause a noticeable decrease of the cooling intensity.

Oct 1, 2019

By Masahiro Shimura, Yoshiki Takahama, Toshiyuki Shiraishi, Daisuke Kasai

When advanced high strength steel (AHSS) is rolled at a high reduction ratio, the forward slip ratio in cold rolling tends to be lower than that of the other softer strips such as low-carbon steels, and the work roll sometimes skids the strip. To identify why forward slip ratio of AHSS at a high reduction ratio becomes smaller than that of low-carbon steel, the relationship between the reduction ratio and forward slip ratio was investigated by a rolling experiment. For this trial, a 4Hi laboratory cold mill was used. AHSS and low-carbon steel coils were rolled by two different rolls that were set to 0.3 and 0.6 μmRa to create two types of friction conditions. Furthermore, the rolling conditions were numerically analyzed to determine the influence of friction coefficient and flow stress on the relationship between forward slip ratio and reduction ratio. The experimental investigation and numerical analysis revealed that the forward slip ratio reduced with increasing rolling reduction ratio in a low friction state; contrarily, it increased with increasing rolling reduction ratio in a high friction state. This feature was clearly visible when harder materials were rolled.

Oct 1, 2019

By Kelen Juliane Mucelin

In order to better understand the tribological behavior of self-lubricating materials, Fe-Si-C matrix composites containing solid lubricants added during the mixing step were studied. The samples were produced by conventional powder metallurgy route, presenting total contents of 5%, 7.5% and 10% in volume of h-BN and graphite mixtures as solid lubricants. The composites were evaluated in terms of tribological properties, under reciprocating sliding conditions, and mechanical properties by using tensile tests. Additionally, the wear scars were characterized by Raman spectroscopy and scanning electronic microscopy. Higher total contents of solid lubricants greatly increased scuffing resistance however decreased mechanical properties. Furthermore, increasing h-BN contents reduces both properties. These results confirmed the applicability of such sintered composites as self-lubricating parts, reaching values up to 7000 N.m for scuffing resistance combined with ultimate tensile strength of 220 MPa.

Jul 31, 2018

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By André Carlos Silva

Dewatering stage is among the most important industrial unit operations, and is wide adopted in many different industries, due the fact that a large portion of industrial products is produced using suspensions of solids in liquids. Nowadays the mineral processing tailings disposal is a big problem due the environmental degradation produced. The phosphate rock processing in Anglo American Phosphate Brazil, situated in Catalão/Go/Brazil, generates around 180 t/h of tailings for a plant feed of 480 t/h (approximately 37,5% of the processing plant feed), with 5 to 10% of solids and approximately 14% of P2O5. Nowadays the tailings are sent direct to the tailings dam. The present work proposes the paste production using with the tailings from phosphate rock processing plant divide in two different stages. The first one composed by the free settling of the material in presence of industrial flocculants in a graduated cylinder with 2.0 L of internal volume for one hour, in the same way it must occur in conventional thickeners. After that time, the clarified liquid was drained and the remaining pulp was sent to the second stage consisting in the tailings vacuum filtration. Ten different flocculants and nine different filter media were tested. The found results were satisfactory for paste tailings production with solids percentage around 65%.

Aug 8, 2018

By Daniela Mota Paschoal Veloso da Silva, Gabriel Filinkoski, Suelen Silva Rocha, Jorge Luiz Valença Mariz

A previsão da fragmentação da rocha é essencial para otimizar a operação de desmonte de rochas. A fragmentação depende de muitos parâmetros, como propriedades estruturais e geomecânicas do maciço rochoso, geometria do plano de fogo das detonações e propriedades dos explosivos. Neste contexto, este trabalho objetivou realizar a previsão da fragmentação por simulação do desmonte de rochas da Mineração Megaípe considerando as características estruturais e geomecânicas inerentes à formação do maciço rochoso através da metodologia de Kuz-Ram. A metodologia consistiu no levantamento das propriedades geométricas das descontinuidades visíveis na face da bancada existente, realização da classificação geomecânica através dos sistemas Rock Mass Rating (RMR) e Q e aplicação dos resultados para predição da distribuição granulométrica da fragmentação. Obteve-se como resultado da simulação que cerca de 90% do material fragmentado deve passar na abertura do britador primário disponível na pedreira, além de resultados favoráveis quanto às análises de condições de estabilidade do talude operacional.

Oct 3, 2019

By Vitor Guarnier Domiciano

Pre-shaped refractory burner blocks play an important role in reheating furnaces operation and melt shops production since they are responsible for heating the billets/plates so that they reach the temperature required for lamination. This paper presents the main characteristics and properties of a new refractory castable developed for pre-shaped burner blocks, which significantly improved the performance of reheating furnaces burner blocks. Tests carried out in 3 different melt shops have shown that the new refractory castable was able to extend the service life of the refractory burner blocks from 1 year (standard product) to more than 3 years (new castable), showing perfect conditions to continue operating for a longer period.

Oct 30, 2017

By Rafael Abreu Fraga, Carlos Noberto Paula da Silva, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Since 2016 Gerdau Ouro Branco has been producing steel plates of various qualities and grades. However, it was not until 2018 that the first plates produced by accelerated cooling process were made available for external testing, in this case for large diameter UOE pipes manufacturing. Recent line pipe and OCTG specifications are showing that the oil and gas market still consumes regular API grades, such as X60, X65 and X70, however with increasing wall thicknesses, reaching values up to 1.5 inches. These specifications also demand longitudinal and transverse tensile guarantees and drop weight tear tests in temperatures as low as -40°C. Projects with these types of mechanical properties present process requirements as challenging as those necessary for higher API grades in lower thicknesses. This paper shows the steel design concepts and rolling routes for achieving the necessary properties for X70 steel plates in 28.15 mm. The microstructural features were also investigated and associated with the production process and the tensile and toughness results. Finally, challenges such as tensile anisotropy and DWTT abnormal fracture are presented.

Oct 1, 2019

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By Andreas Jungbauer

The Chinese steel producer Rizhao Steel is now focusing on the highly attractive local and export markets for high-quality, thin-gauge strip products. The first line of five Arvedi ESP plants began operations in the spring of 2015. The new casting-rolling complex is designed for a total annual production capacity of 11 million tons of highquality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The energy consumption and related costs are reduced by up to 45% compared with conventional casting and rolling processes. This also means a major reduction in CO2 emissions. During the project phase, the plant personnel from China received extensive training at the licensor’s plant – Acciaieria Arvedi S.p.A. in Italy – to prepare them to deliver the best operational performance with the new state-of-the-art endless casting-rolling facility. The plant setup, the training and support program, as well as the latest results from the start-up are presented in this paper.

Aug 16, 2017

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Patrick Edward Connell

The next generation of the well-established 3-roll Reducing & Sizing Block (RSB), the RSB SCS® is the latest milestone in reducing and sizing technology for SBQ products. It offers enhanced bar quality, improved productivity, mill availability and economy as well as a simplified, safe and environmentally friendly operation. A newly developed modular drive concept of the RSB SCS® grants a smaller footprint in the layout, a reduced oil-lubrication volume and a simplified maintenance schedule. Intelligent engineering leads furthermore to reduced hydraulic functions of the RSB SCS®, which ensures a safe and environmentally friendly rolling. Another integral part of the RSB SCS® is an innovative stand changing concept, which allows automatic stand changing within three minutes. The new RSB SCS® also includes a Fast Remote Control (FRC) which enables the immediate adjustment of the roll gap against the rolling force (under load) within milliseconds. Size changes along the free-size range can also be made within the traditional billet gaps in less than five seconds. At the core of the future-oriented RSB SCS® is a real-time closed-loop control system called Size Control System (SCS®) acting with 3-roll stands adjustable under load (AUL) and / or the heavy duty stands. These features remarkably further improve the rolled tolerances and their reproducibility, and at the same time simplify the operation by means of an automated optimization of the process parameters for the rolled bars.

Aug 16, 2017

By Gustavo Borges Tiboni

The erosive wear caused by the impact of solid particles against a surface is a tribological phenomenon present in many segments of the industry, such as transportation, aerospace, mining, power generation, among others. The most usual method to set the wear rate is by measuring the mass loss of the material. In order to apply one technique with potential to determine the rate of erosion wear, this study developed a dedicated equipment and conducted preliminary erosion tests monitored by non-destructive testing known as acoustic emission technique (AE). This can be defined as a technique able to detect mechanical waves generated by the release of elastic energy accumulated in the material. Erosion tests were performed in order to evaluate the ability of equipment to collect data from AE and to correlate these data with the wear of the samples. Samples of low carbon steel eroded by the impact of angular aluminum oxide particles suspended in air at three different velocities: 45, 57 and 67 m/s. The impact angle between the particles and the sample was set at 30 degrees and the test temperature at approximately 20°C. The wear rate has changed with the velocity in accordance with the kinetic energy of the particles and the AE parameter RMS showed sensitivity to the variation of particle impact velocity and to the wear of the sample eroded. The rate of AE signals collected over time correlated with the flow of particles striking the sample, and with the parameters of energy, rise time and duration of the signal.

Jul 31, 2018

By Karl Berger

Today we are talking about Industry 4.0, as the latest revolution of industrial processes and progress, considering that the steam engine (Industry 1.0), railways and cars, mass production in the 1920th (2.0), Industrial Automation (3.0), and finally integrated manufacturing, integrated communication, and internet (4.0) can be seen as the state-of-the-art situation in industry, nowadays. Similar to the Industry progress, we can approach the rolling process of material, which started about 150 years ago in a very basic way. Steam engine- and belt driven-mills were very operators’ intensive, brutal and risky to operate. Mechanical improvements brought throughput, safety and quantity, as also quality of the products. The rolling of steel, in particular of rails, beams, rebar, strip (focus in this paper) and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. From single stands to continuous rolling trains the production and quality of mills increased significantly. From ingots and blooms to slabs, we have to admit a big jump in which has changed the face of the world significantly. Thin Slab Rolling has revolutionized the output and the throughput of rolling mills (Generation 3.0 to 5.0). Finally, Endless Rolling, has boosted the quality and quantity of rolling mill processes and permitted nowadays to enter in market niches which were not thinkable a decade ago. Mastering the automation and applying reliable systems (mechanical and electronically) of drives, actuators and sensors, as also communication and information interchange to all levels of automation are the success factors of such complex mills, we call herein after “Rolling Mills of Generation 6.0”.

Aug 16, 2017

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017