Search Documents

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By E. E. Wark, J. Rogers, I. W. Wark, K. L. Sutherland

SOAPS have been used as collectors for many years, but only in the last eight years have other long-chain paraffin salts been used. It may be anticipated that these newer collectors will be used mainly with nonsulphide minerals, for which the xanthates and similar compounds are of little value. On the other hand, the xanthates are both cheap and effective for sulphide ores and seem likely to retain their present eminence in this field. During 1938 and 1939 two of us (E. E. W. and I. W. W.) commenced a comprehensive investigation of the principles underlying the use of paraffin chain salts as flotation reagents. This research was sponsored jointly by the University of Melbourne and a group of Australian mining companies.[t] A broad, semi quantitative survey was then made of the field covered in the present paper. This was followed in 1940 by further work by one of us (K. L. S.). In 1941 the investigation was taken over by the Division of Industrial Chemistry of the Commonwealth Council for Scientific and Industrial Research, Australia. Discovery of some principles upon which are based the flotation of minerals by paraffin chain salts was followed by their application in the development of processes for the recovery of certain strategic minerals from their ores. Promising results in the flotation of cassiterite from various ores will be described in a subsequent paper. THE PARAFFIN CHAIN SALTS The basic requirements for a "collector" in flotation are that it should form a film over the surface of the mineral to be floated, and that this film should be orientated so that hydrocarbon (nonpolar) groups form the effective surface. When modified in this way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince23 that such a film can be produced only if the collector compound contains an active (polar) group to attract it to the mineral surface as well as the nonpolar group. One section of this large class of polarnonpolar compounds is the paraffin chain salts: CH3(CH2) „X where X signifies a polar group that ionizes in aqueous solution. Though the compound can ionize, it may be a weak or a strong electrolyte, and the hydrocarbon chain may be in the cation or the anion (Table I). Many compounds of similar constitution are available, but the usual polar groups are: -CO2Na, -SO3Na, -SO4Na, - PO4Na2, or an aminonitrogen group, the

Jan 1, 1946

Discussion of the papers of Messrs. Howe and Levy, Burgess, Crowe and Rawdon, and H. M. Howe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1075 to 1136. ALFRED STANSFIELD, Montreal, Canada :-In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated. for "grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus, to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the " Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated above the solidus (curve Aa on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 12, 1913

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By William J. Craig, Harold L. Walker

INDUSTRY has for many years recognized the dependence of certain mechanical and physical properties, as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain- size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. LITERATURE A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing, The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbs1 has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered, Townsend and Greenall2 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1948

By J. E. Hilliard

A procedure is described for determining, from measurements on a section, the moments of any degree n (i.e., the mean value of Dn, where D is a linear dimension) of the size distribution of particles (or grains) in an opaque sarnple. The analysis is applicable to particles of alnzost any shape and to any mixture of shapes. However, if absolute values of the wloments are required, it is necessary to know what shapes are present and the relative frequency of their occurrence. In addition, certain shape-dependent parameters have to be evaluated before the formulas can be used. The measurement required is the distribution of intercept lengths. This can be determined either visually or with an automatic scanning instrument. Corrections me derived for the bias due to instrumental end effects. The proposed analysis has the following advantages over existing ones: 1) Confidence limits are easily estimated for the measured properties or, conversely, the number of counts required to achieve a given accuracy can be determined. 2) The analysis is not restricted to particles of a special shape. 3) The error resulting from any known degree of departure of the actual from the assumed particle shape can be estimated. 4) The computations are simple and, apart from a change in constants, are independent of particle shape. 5) The number of particles per unit volume can be determined by a simple counting procedure. MANY procedures have been described for determining the size distribution of particles from measurements on a section (or plane of polish). They differ from one another in the property measured on the section (radius, intercept length, profile area) and in the method used for the numerical solution of the integral equation relating the property to the particle size distribution. However, all existing analyses share at least two of the following disadvantages. 1) They are limited to a particular shape of particle (usually spherical). 2) It is very difficult to determine how the statistical sampling error is propagated into the computed size distribution. The investigator thus has no means of knowing the reliability of his result and, what is of equal concern, he is unable to estimate how many measurements are required to obtain a result of the required accuracy. 3) It is also difficult to assess the error resulting from any deviation between the actual and assumed particle shape. The foregoing limitations stem from the complex relationship between the particle size distribution and the distribution of the property measured on the section. As will be shown, they can be avoided by defining the size distribution in terms of discrete parameters

Jan 1, 1969

By G. L. Boxer, C. B. Smith, W. J. Atkinson

Since the inception of the Ashton (formerly Kalumburu) Joint Venture in 1972 the parties have expended $24 million in exploration for diamonds in the Kimberley region. This has resulted in the discovery of the currently subeconomic Ellendale deposits in 1976/77 and the economic Argyle - Smoke Creek Deposits in 1979/80. In addition to Argyle and Ellendale, some 90 kimberlitic and lamproitic bodies have been discovered grouped broadly into three provinces, on the west, east and north margins of the Kimberley block. These bodies range in size from dyke-like features less than 1 m (3 ft) in width to pipes with a surface area of 128 ha (316 acres). The bodies with larger surface area are volcanic crater deposits, infilled with air-fall and water deposited tuffs and epiclastic sediments. Diamond content ranges from trace to economic concentrations. The exploration discoveries were facilitated by early recognition that the petrography, mineralogy and chemistry of the diatremes varied from the classical kimberlites of Kimberley, South Africa, to unusual more highly fractionated, alkaline, silicic varieties having affinities with leucite-lamproite. Indirect methods of exploration were used, primary reconnaissance work being stream gravel sampling for kimberlitic indicator minerals. Evaluation showed Ellendale diamonds are 90% gem and near gem, but the low grades and tonnage render the deposits unpayable at today's diamond prices. After discovery in late 1979 and completion of a feasibility study by the end of 1982, evaluation studies proved Argyle to be economic. Alluvial diamond mining commenced in 1983 producing 6.2 million carats (Mct) that year, 60% being of industrial quality. Open-pit mining of the AK1 lamproite should start in 198511986 at a rate of 3 million t/a (33 million stpy) and produce 25 Mct/a, making this mine, and Australia, the world's largest producer of diamonds by weight. The revenue from diamond deposits is a function of the grade and the value of the diamonds. The grade is the product of the frequency of occurrence of the diamonds (stone density) and the mean stone size; the value of the stones is strongly related to their size distribution. During evaluation of the West Australian deposits, the diamond distribution was found to vary markedly in stone density and stone size. These variations corresponded with changes in the rock type hosting the mineralization. As a consequence, geological mapping of individual lamproites within the multiple vents and careful monitoring of the diamond distribution became an important part of the evaluation work. Similar variations in stone size and frequency were found to accord with separate alluvial terraces and fan gravels derived by erosion from the Argyle AK1 lamproite.

Jan 1, 1985

By J. T. Peters, N. Schapiro, R. J. Gray

Petrographic studies of coal have resulted in a better understanding of the origin and composition of coal and have added to the knowledge of how and why coals differ in their response to various prepamtion and utilization processes. Petrographic methods can now be used in scientific economic exploitation of coals. Because the United States Steel Corp. is one of the largest consumers of coal and coke, there is a continuing interest in the corporation in perfecting a better understanding of coal so that it can be utilized more effectively. Coal is a heterogeneous substance composed principally of plant material that has been altered by a complex geochemical process to form rock. The science of coal is anthracology. The ultimate aim of anthracology is determining the relationships and differences among coals. The fundamental aim is finding out why coals differ. The practical application is determining how the differences in coals affect their utilization properties. Coal, like other sedimentary rocks, consists of more than one material. Fig. 1, a photograph of a natural fracture and a polished surface of a lump of coal, displays heterogeneity in terms of the banded ingredients present. The earliest attempts to describe coal were based on its hardness and appearance. ' Thus, coal has been described as hard or soft, bright or dull, and banded or nonbanded. The variations in the hardness and physical appearance of the coal reflect differences in materials that constitute the coal. The banded nature, lustre, and texture depend upon the relative proportions of the various constituent materials. Even the earliest petrographic investigations of coal produced evidence of of the heterogeneity of the coal substance and shoul have destroyed the concept of the unit coal molecule. Coals (Fig. 2) that appear the same frequently consist of different microscopic materials and may behave differently during mining, pulverization, washing, or coking. In Fig. 3, the upper photograph shows a bright at-trital medium-volatile coal, and the micrograph at the right shows some of the materials that constitute the coal. The lower photograph shows a bright attrital low-volatile coal and the corresponding micrograph shows material of similar origin to those from the medium-volatile coal. Any petrographic description of a coal that has meaning in terms of its utilization begins with a microscopic examination. Numerous attempts have been made to describe coal on the basis of the materials that constitute the coal.2*3 Initial petrographic studies were directed towards the question of the origin of coals without any true basis for studying the metamorphic changes in the

Jan 1, 1962

By J. H. Frye, R. M. Treco

ONE of the chief hindrances to an understanding of the hardness of solid solutions is the sparsity of suitable hardness data. There is great need of a large body of hardness data obtained from many different alloys of high purity by identical testing methods and corrected to correspond to a single grain size. A considerable amount of such data has been obtained by means of the Meyer analysis on copper-rich and silver-rich solid solutions. There are enough of these data to permit comparison of numerous alloys at equal solute concentration in these two solvents, but only in a few cases is it possible to construct hardness-concentration curves for any given alloy. Therefore additional hardness work on most of these alloys is desirable. The primary solid solutions of silver with cadmium, indium, tin, or antimony as solute are of special interest, since all elements are from the same period of the periodic table and since, as shown previously,1 the hardening effect of equal percentages of these solutes is proportional to the lattice expansion produced by them. This paper presents the relation between hardness and concentration in the silver-antimony system from very dilute to nearly saturated solutions of antimony in silver. EXPERIMENTAL PROCEDURE Alloys were made from silver, 99.99 per cent pure, and antimony, 99.975 per cent pure. Silver and antimony were placed in graphite crucibles that had an ash content of less than 0.75 per cent. These metals were melted and allowed to solidify in a vacuum, which, after melting was complete, was usually equivalent to 3 mm. Of mercury. A high-frequency furnace was used. The ingots so obtained were worked and annealed to lessen segregation and to control grain size. Annealing was done in evacuated and sealed glass tubes. Hardness measurements on specimens from these ingots were by means of the Meyer analysis.3,4 Using a 4-mm.. ball, impressions were made under seven loads from 25 to 400 kg. The diameter of impression made under each load was measured. This enabled calculation of the constants in the well-known formula of Meyer. L=ad¬n where L = load, d = diameter of impression, a = a constant, n = a constant The Meyer hardness is defined as P = L/(1/4pd2) or P = 4adn-2/p Meyer hardnesses corresponding to d = 1 and to d = 4 are of especial interest, since the first corresponds to comparatively slight plastic deformation and the second to the maximum plastic deformation producible by penetration of the ball. These

Jan 1, 1944

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A' ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author's intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner's theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed' he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,' in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By C. G. Dunn

Nuclei that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,&apos; that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclasses† of the 36 third-order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of deformation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a (110) plane in a <100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is not particularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1947

By C. G. Dunn

Nuclei that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,&apos; that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclasses† of the 36 third-order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of deformation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a (110) plane in a <100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is not particularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1947

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,&apos; it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,&apos; it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By E. F. Raffo

THE design of the Chuquicamata concentrator offered an unusual combination of problems, all of which had, in one way or another, a definite effect upon the final arrangement of all the equipment and necessary facilities. First of all, a remotely located project of this magnitude required careful selection of equipment with an adequate supply of replacement parts and in some cases necessitated stand-by spare equipment ready for immediate use. Fortunately, in the course of determining the proper flowsheet, in itself a prime factor in the concentrator design, it was possible to conduct numerous grinding and flotation tests at the Anaconda and Andes concentrators. As a result of these tests made under actual operating conditions, most of the major equipment best suited for treating the Chuquicamata ore efficiently was decided upon while preliminary design layouts were still being made. The design has been based primarily on the treatment of sulphide ore crushed to about 3/4 or 1 in. However, until the new sulphide crushing plant is completed it will be necessary to handle ore crushed to 3/8 in. in the existing oxide crushing plants and to some extent a mixed ore which has had its oxide copper content removed by leaching. This mixed ore, known as leached residue, will contain a certain amount of sulphuric acid from the leaching process which necessarily requires special protective measures. Several factors influenced the final location of the Concentrator. The only established fact known during preliminary design layout was the elevation of the dumping floor over the fine ore bin. This was predetermined by the desired level railroad grade across part of the existing tailing and leached residue dumps from the oxide plant to the bin. Next it was necessary that a site be chosen that would not require an excessively long haul from either the present oxide plant or the mine and in addition provide a fairly constant natural ground slope sufficiently wide to accommodate the length of the ultimate concentrator. The site as finally chosen to meet the foregoing restrictions provided a natural ground slope of 6 to 7 pct. This was excellent, especially in a region subject to earthquakes, as it assured that foundations of heavy equipment and footings for building and crane columns would rest on cut or undisturbed ground. However, this shallow slope, although having some definite advantages in the overall consideration of plant layout, resulted in the need for extensive studies in the general arrangement of equipment. Wasteful and excessive vertical drops had to be eliminated in the

Jan 1, 1952

Asarco&apos;s Sacaton unit, located near Casa Grande 45 miles southeast of Phoenix, Arizona, was brought into production in February 1974. Ore reserves are estimated at about 48 million tons at 0. 95% copper. Mineralization of the orebody comprises both sulfides and oxides, with minor amounts of gold and silver. Preproduction stripping of 40 million tons of overburden was accomplished in less than two years. Mining is done at the rate of 9,000 stpd ore with a waste-to-ore ratio of 4.6 to 1. 0. The mine is developed on 40 ft benches, and by 1979 underground block caving methods will be phased into the operation at a depth of 1900 ft. Ore is mined in the pit two shifts per day, seven days per week, and is hauled with 85 ton trucks to the primary crushing plant. Trucks dump their loads into a 165 st capacity pocket equipped with a chain curtain which controls the ore flow to the 6 ft 6 in. wide by 24 ft long (2. 0 m by 7.3 m) vibrating feeder grizzly. Grizzly bars are inclined at a 5º slope on the first half of the 0 feeder and 10 on the last half. Grizzly bars have 6 in. (13 mm) spacings which pass 60 to 70% of the mine-run ore. Grizzly oversize drops into a 48 in. by 60 in. (1. 22 m by 1.52 m) primary jaw crusher. Both the grizzly undersize and crusher discharge are collected on a 42 in. (1.07 m) conveyor belt operating 398 fpm (121 mpm) for transport to the 4,750 live st intermediate storage area ahead of the fine crushing plant. Capacity of the Sacaton primary crushing plant is a nominal 1150 stph (1043 mtph). It operates fourteen shifts per week with an effective crushing time of four hours per shift. An economical open-air design was used, but an enclosed operator control room is located on the upper level where the dump truck, feeder, and crusher can be observed. Oversize rocks are removed from the feeder or crusher by the 10-ton bridge crane. Direct operating costs for this well-designed primary crushing plant, including labor, power, supplies, and maintenance, are only 3.5 cents per short ton. An interesting feature of the Sacaton orebody is that the non-sulfide copper minerals, which are less prevalent than the sulfides, occur intimately with the sulfide minerals; for this reason, all ores as mined are treated in a flotation circuit using sulfidizing methods for oxide recovery.

Jan 1, 1978

By M. E. Lombardi

ThE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 81/4 in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling. The problem is to reach a depth of 4,000 ft. or more with a string of

Jan 1, 1915

By C. Y Garber

Interest in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator&apos;s viewpoint only; no effort is made to discuss it in a theoretical or technical manner. Plant at Bunker Hill The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a 1¼ in, screen and is then washed and separated on vibrating screens having 4½-mm. round-hole punched plates. The screen under-size, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass 36 in. and joins the under-size in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. Preparation OF Medium at Bunker Hill New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1947

By C. Y. Garber

Interest in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator&apos;s viewpoint only; no effort is made to discuss it in a theoretical or technical manner. Plant at Bunker Hill The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a 1¼ in, screen and is then washed and separated on vibrating screens having 4½-mm. round-hole punched plates. The screen under-size, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass 36 in. and joins the under-size in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. Preparation OF Medium at Bunker Hill New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1947