Search Documents

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By W. M. Weigel

Salt production in Louisiana and Texas at the present time is entirely from salt domes of the interior and coastal groups. Before and during the Civil War salt was recovered from numerous salines and salt springs by evaporation in open kettles. The location of these in nearly every instance was near what is now known to be a salt dome, and the source of the salt in the salines and spring waters was that in the salt core. The tops of many of the shallower domes have been subjected to erosion1. The discovery that the salt occurred as large masses of rock salt in the form of domes was made in May, 1802, at Avery Island, La., by John Marsh Avery, grandson of the original owner, John C. Marsh, who built the old salt works in 18122. The first shaft for mining was sunk on the Avery dome in 1867 by Chouteau and Price. It was 90 ft. deep, about 58 ft. being in solid salt. It was abandoned in 1870. There are three general groups or fields of salt domes; interior Louisiana in northern Louisiana, interior Texas in northeastern Texas, and the coastal domes nearer the Gulf Coast and extending from the Mississippi River to the Rio Grande. This last group contains by far the greatest number of domes. As many of the coastal domes especially are prolific producers of petroleum and a few of sulfur, their geology has been intensively studied and fully covered in the literature. The depth to the top of the salt varies from near the surface, where shallow ground waters have dissolved the salt to just below recent deposits, to several thousand feet, where the depth has been cstimated only by geophysical methods. The diameter of the salt core varies from less than 1/2 mile to over 2 miles. Only domes where the salt is comparatively near the surface have been developed for commercial salt. Three deeper domes, which will be described later, have recently been developed or are in process of development, as a source of brine for chemical use. Fig. 1 shows the location of the domes so far developed for commercial salt and brine. Nos. 1, 2, 4, 7, 8, 9 and 10 are in the Gulf Coastal field,

Jan 1, 1938

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.' Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining 'the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By Daniel D. Pollock

The il'lott and Jones theory of thermoelectricity predicts that the absolute thermoelectric power of alloys of transition and noble metals should be a maximum when the concentration of the noble metal is approximately 55 to 60 at. pct. An examination of the emf of a series of relatively pure alloys of copper and nickel shows that the predicted maximum occurs at about 57 at. pct Cu. This excellent agreement with the theory is considered to substantiate the Mott and Jones theory of thermoelectricity for binary alloys of transition elements. This theory is extended to show that the emf behavior of dilute, ternary copper-nickel base alloys, which contain approsimately 60 pct Cu and 40 pct Ni, may be described in terms of a scattering mechanism. The scattering effect of a third element is demonstrated to be a function of its valence and its period in the periodic table. Small amounts of solute elements have additive scattering effects upon the emf of the Cu-Ni base. The Mott and Jones equation is modified to include this scattering parameter. This adaptation accurately describes the thermoelectric behavior of ternary and quaternary CLL-Ni base alloys. An empirical form of the modified Mott and Jones equation is derived which permits the calculation of thermoelectric power with an average error of less than 0.4 pct at 500 "C. CONSTANTAN has long been used as a thermocouple element. Its approximate composition varies from 50 pct Cu, 50 pct Ni to 65 pct Cu, 35 pct Ni. Small amounts of manganese, iron, and other elements have been used to modify the composition in order that the resultant emf vs platinum conforms to nationally accepted table. Adjustments of this type are made on a purely empirical basis. Constantan was originally made in Germany and was imported into this country for thermoelectric and electrical resistance purposes. During World War I, the supply of this material became seriously depleted. The work of Bash4 was done in this period in order to develop a satisfactory substitute for the imported material. Bash's empirical work on Cu-Ni alloys is still the basis for all commercial constantans made in this country. No reexamination of the electrical properties of this system has been made, despite the fact that it is now well known that Bash's alloys contained impurities which strongly affected their thermoelectric behavior.

Jan 1, 1962

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

By J. R. Thoenen

The Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy. Introduction On December 11, 1946, R. D. Longyear, in his capacity as Chairman of the Subcommittee on Exploration Drilling, wrote the author requesting him to prepare a paper presenting the collective ideas of engineers in the Bureau of Mines on the design, standardization and application of core barrels using diamonds or other hard cutting media for drilling holes larger than two inches and less than ten inches in diameter. In subsequent correspondence it was indicated that similar papers covering the experience of other government agencies would be solicited and all such papers received would be combined in a symposium on the subject for discussion at the March 1947 meeting of the Mining Methods Committee AIME. In soliciting such information from other Bureau engineers, it developed that most Bureau experience had been confined to standard core size, two inches or less in diameter, and that larger sizes had been used only for special purposes. It is hoped the data contained herein will be of help to other operators in solving problems encountered in the field. Acknowledgments This paper was made possible by the request of Lowell B. Moon, Chief, Mining Division, Bureau of Mines, to all Division engineers to send to the author any data they had on the subject. Engineers of the Mining Division contributing were: M. H. Kline, Chief, Raleigh Branch. Paul T. Allsman, Chief, Salt Lake City Branch. J. H. Hedges, Chief, Tucson Branch. C. H. Johnson, Chief, Rolla Branch. A. M. Evans, Mining Engineer, College Park Branch. Wing Agnew, Engineer in charge, Mount Weather, Virginia. Andrew Brown, Mining Engineer, Tus-caloosa Branch. In addition Albert L. Toenges, Supervising Engineer, Bituminous Coal Mining Section, Pittsburgh, contributed his experience in coring coal beds. The author's experience in the use of cores within the limits stated has been confined to the brown iron-ore work described by Brown and coring bauxite and clay in Arkansas. Design and Standardization of Core Barrels Bureau engineers are primarily interested in obtaining core that will best represent

Jan 1, 1949

THE CHAIRMAN (A. F. Lucas, Washington, D. C.).-Mr. Matteson has stated that the drilling of certain deep wells has proved a failure because they were abandoned too soon. He advises drilling more wells around salt domes, in the hope of finding additional oil sands. I have had some experience on the domes and believe that by drilling shallow wells, one loses time and money. I have advanced the opinion -that by drilling central wells in the -most likely location of a dome, showing is certain weakness, a better result could be obtained. I have in mind one locality where Mr. Knapp drilled a well through the salt¬the only location that I know of on the Gulf Coast where oil was found underneath the salt. Mr. Knapp found a great deal of gas in it. The salt itself was impregnated with oil and gas; and my opinion is that in such instances, instead of drilling so many wells around a dome, if you will attack at a weak point to as great a depth as a drill will go, the results will he much better. At present we have instances where drills have penetrated to 7300 or 7400 ft. in depth. Why couldn't the rich companies that are operating around the Gulf Coast arrange to get some special drilling apparatus and drill with the rotary first for, say, 3000 to 4000 ft., always in the likely location, and then proceed with the cable? I think we need just such work. In Mr. Matteson's paper lie quotes from an author whose writings in the Federal Bulletin and in the Louisiana Bulletins have been quite extensive. He states that oil and asphalt have originally been found on the surface of those domes. I have been over and examined nearly all of those domes (not all of them, because many have been developed in the last few years) and found no such occurrence at the time; and in the old well-known humps or big hills, as they generally called them; I have never found either salines or asphalt or petroleum. In only' one instance it looked as though asphalt night have exuded out of the ground, and that was in the Sour Lake, but right in that neighborhood years previous to that a company had operated commercially-they had a little refinery there-and had found it so unprofitable that they pulled up stakes and quit.

Jan 4, 1918

By Thomas W. Dawson

THE H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnage and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center, to center of pulleys. It operated at a speed of 250 ft. per min. and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons were carried by the belt. While this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on, the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and,, therefore, had to be crossed at each location to deliver coal to the river.

Jan 6, 1925

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By M. H. Richman, E. S. Meieran

An analytical method is presented which enables the electron diffraction patterns from a twinned region to be indexed. The method has only been applied to (112) twins in bcc lattices, but can easily be adapted to other types of twinned lattices. Calculations of all twin spots, including those superimposed on matrix spots, is made possible by this method. SINCE the advent of transmission electron microscopy, the analysis of selected-area electron diffraction patterns has become very important in the interpretation of electron micrographs. Frequently, as in the case of some martensites, twinned areas are observed and give rise to complex diffraction patterns, which so far can be analyzed only for the simplest orientations of the thin foil specimen with respect to the electron beam. In order to simplify the analysis of twin patterns of more complex orientations, an analytical method was devised which is capable of predicting the positions of all reflections from both matrix and twin regions for all possible foil orientations. Although the method has only been applied to the case of bcc metals twinned about a (112) plane, it is equally applicable to other Bravais lattices. This method has been successfully applied to selected-area electron diffraction patterns of Fe-Ni and Fe-Ni-C martensites and drawn tungsten wire. PROCEDURE Imagine the reciprocal lattice corresponding to a bcc material, with each point hkl representing the crystallographic plane (hkl). Since the extinction conditions require that for this lattice, only reflections where h + k + 1 = even integer are allowed, the three dimensional reciprocal lattice is actually fcc. Since in real space twinned regions and matrix regions are mirrored across a (112) plane, the twinned reciprocal lattice is derived from the matrix reciprocal lattice by a rotation of 180 deg about a (112) direction. While it is possible to calculate how a point hkl will shift under a twinning transformation to a new point htktlt using only the reciprocal lattice based on the orthonormal vectors [100], [010], and [001], the calculations are greatly simplified if a new orthonormal coordinate system containing the twin axis is introduced. The twinning operation then becomes a simple rotation of 180 deg about a principal coordinate axis (in this case the twinning axis), and a retransformation back to the original reciprocal space will give the position htktIt of the twinned reflection.

Jan 1, 1963

By Charles Burrows

THE burden a man can endure depends on its magnitude and the number of tunes it is applied, as well as on many other factors. The resisting power of steel likewise is dependent on many factors. The maximum load it can support indefinitely is much less than its possible momentary burden. A light load straining the metal far within its elastic limit, if repeated indefinitely, ruptures the metal. The magnitude f the stresses that may be alternately applied and removed without rupturing the material depends on the number of repetitions of the cycle; the intervening periods of rest; the thermal, electric, and magnetic conditions, as well as the presence of secondary stresses. While we are unable to formulate the law between the magnitude f repeated stresses necessary to produce rupture and the length of time during which these alternating stress may be applied before rupture, my experience is that the time increases as the magnitude of the force decreases, according to a law which, to a first approximation, is exponential. In other words, F = Ce-t where F = magnitude f alternating stresses; = time for which stresses are continued; C = constant, which' depends on the conditions under which the operations are carried out. It is quite probable that the same type of law holds for the magnitude of a continuous force and its duration. When a rod of steel is subjected to the blows of a drilling hammer several things happen. First, one end is struck by the hammer and the other end is driven into the rock, thus causing a bodily displacement of the entire material of the steel drill. The greatest stresses involved in this bodily displacement are located at the two ends of the steel and manifest themselves by the distortion of these parts. Second, after the blow has been delivered the steel drill, due partly to its own resiliency and partly to the resiliency of the rock, experiences a vibratory motion as a whole, this motion is quite similar to the bouncing of a rubber ball thrown violently upon a smooth pavement. Third, the free vibration of the drill is determined only by its own natural period of vibration. This motion involves all the characteristics f any vibrating body emitting sound. Certain elements of the rod will experience alternations of condensation and rarefaction and, in these regions, the individual steel

Jan 6, 1921

By S. S. Nosseir

INTRODUCTION General Quebec Cartier Mining Co. (QCM) , Canadian subsidiary of U . S. Steel Corporation, operates two iron ore concentrators at the North Shore of Quebec, Canada. In its own operation at Mount-Wright, over 45 million tons per year of crude ore are ground, fully autogenous in six 32' x 11-1/2 Dominion Engineering mills. At Fire Lake/Lac Jeannine operation, property of Sidbec Normines Incorporated (SNI), over 11 million tons per year of crude ore are now ground, fully autogenous, in twelve 18' x 5' Hardinge mills. The Lac Jeannine concentrator was originally constructed by Q.C.M. in 1960 and. was since operated, in beneficiating the Lac Jeannine ore deposit until fully depleted in 1977, at an annual capacity of 18 million tons of crude per year. In 1976, the new company, Sidbec Normines, was incorporated by Sidbec Corporation, British Steel Corporation and Quebec Cartier Mining Co., in proportional holding of approximately 51 to 41 to 8 percent respectively. Since the acquisition of the Fire Lake ore deposit and Jeannine concentrator by the new company, QCM has continued managing the mine and concentrator operaions for S idbec Normines Inc . Flow-Sheet Design Jeannine concentrator comprises twelve identical mill lines grinding the ROM from 8" top size to 14 mesh nominal size range. Driven by 600 H.P. motor at 13.4 RPM corresponding to 73% critical speed, each mill is operated in a closed circuit with two 5' x 12' vibrating screens dressed with 2.5 x 25 mm slot opening cloth. The ground product or screen undersize at an average grade of 33.4% Fe is beneficiated by gravity separation to produce 66.5% Fe concentrate grade at 42.7% weight recovery. At the rougher stage, each mill line con-tains 128 Humphrey 13- 1/2" pitch spirals which produce a final tailing, middling and concentrate products. The rougher concentrate - so produced - is classified by 64 Humphrey pocket sizers into an underflow, which is a final concentrate product and an overflow which is further upgraded by 64 cleaner spirals. The cleaner concentrate together with the pocket sizer 's underflow are dewatered on a 13'[6] horizontal filter. The rougher middling together with the cleaner tailing are recycled in a closed circuit with the spirals. The rougher tailing after dewatering by hydrocyclones is disposed of by a

Jan 1, 1982

By J. Gurland

The strength variation ofWC-Co alloys with composition and particle spacing falls into two ranges. 1) Above a critical value of the mean free path, the strength follows a dispersion hardening relation; it is proportional to the volume fraction of WC and in-versely proportional to the particle size. 2) Below a critical value of the mean free path, the strength variation is based upon the Griffith criterion of fracture and is controlled by the case of crack propagation. The maximum strength is attained when the structure and load just satisfy the critical conditions for spontaneous crack propagation. THE relation between the strength and the structure of cemented carbides is of interest not only for its own sake but also for its contribution to the understanding of composite materials in general. The cemented carbides are essentially aggregates of a brittle carbide constituent and a ductile binder phase and, at certain structures of intermediate composition, the composite alloys attain strengths far higher than those of the separate constituents in bulk. It is this variation of strength with structure which will be discussed. The experimental procedures of sample preparation, mechanical testing, and quantitative metallo-graphic analysis have been described in Ref. 1. The reported strengths are the maximum fiber-stresses in bending calculated on the basis of completely elastic behavior. The plastic contribution to the over-all deformation is small and was neglected in the calculations (the elongation at fracture of the most ductile alloy, 50 pct WC-50 pct Co, is less than 0.5 pct).2 The pertinent structural parameters are: f, the volume fraction of tungsten carbide; p, the mean free path through the binder phase; the contiguity C, defined as the average fraction of surface area shared by a particle of wc with all neighboring particles of the same phase; and d, the average equivalent spherical diameter of the WC particles. The strength variation of WC-Co alloys with composition and particle spacing is shown in Fig. 1 and Table I, which are based partly on previously published data' and partly on new experimental work which extends the range to higher values of the mean free path. Each data point represents the average of five samples. For a given composition, the transverse rupture strength reaches a maximum

Jan 1, 1963

By W. M. Weidel

While electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test. Description of Apparatus Used The candlepowcr was determined with a Weber photometer, Fig. 1, which consists of a tube A containing a movable milk-glass screen adjustable by the milled screw B. The distance of this screen from the standard light at C is read on the scale attached to A. The standard light consists of a benzine lamp so arranged that the height of the flame may be adjusted exactly by observing it against a scale in the lamp box through an opening in the front. The lamp to be tested is placed at D so as to illuminate a milk-glass screen in the holdcr at E. At the intersection of the axes of tube A and sight-tube F are placed two 45' prisms with their surfaces in contact so that the light from D may pass through with-

Jan 1, 1917

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929