Search Documents

By James T. Waber, Allen C. Larson, Karl Gschneidner, Margaret Y. Prince

The original graphical method proposed by Darken and Gurry for predicting which elements are soluble in a given element was slightly modified and was used to predict terminal solubilities in 1455 known binary combinations. it was found that the modified Darken and Gurry method had a reliability of 61.7 pct in predicting extensive solid solubility (greater than 5 at. pct) and of 84.8pct in predicting limited solid solubility (less than 5 at. pct), an over-all reliability percentage of 76.6. Using the same experimental data, it was found that using only the simple Hume-Rothery size-effect criterion was 50.1 pct reliable in predicting extensive solid solubility, only slightly better than a purely random choice. and 90.3 pct reliable for predicting limited solid solubility, an over-all reliability percentage of 67.6. THE first rational rules for determining a priori whether two metals are not freely soluble in the solid state were announced by Hume-Rothery and coworkers.1,2 These well-known rules have been accorded a special place in metallurgical literature. Since the "electronegative" and "relative valence effect" rules of Hume-Rothery were only qualitative in nature it was difficult to use them in a quantitative analysis. The next major step was made by Darken and gurry3 and apparently went unexplored for a number of years. They prepared graphs illustrating the influence of both electronegativity and size difference on the solubility of elements in silver, magnesium, and aluminum, and they drew elliptical figures, whose maximum width was ±15 pct of the solvent radius and the maximum height was ±0.4 electronegativity units. The purpose of the present paper is to assess and compare the effectiveness of using the simple size-factor and the Darken-Gurry criteria to predict which elements will be soluble and insoluble in a given solute. In 1957, waber4 prepared Darken-Gurry plots for determining the solutes that were likely to be soluble in 6 and plutonium and introduced an inner ellipse as an aid to determining which elements should be soluble to a considerable extent. As illustrated in Fig. 1, the major axis of the outer ellipse corresponded to ±0.4 electronegativity units (OD) while the minor axis corresponded to ±15 pct of the radius of the solvent phase (OB). This simultaneous "action" of the two Hume-Rothery criteria was used to indicate which elements would have little or no solubility in the host lattice, namely those elements whose points lay outside this ellipse. An inner ellipse, "centered" over the same point of the solvent was drawn with ±0.2 electronegativity units (OC) and ±8 pct (OA) as the major and minor axes. Solutes with points lying within the inner ellipse were expected to be capable of forming extensive solid solutions with the host element. Use of this method of applying the earlier Hume-Rothery criteria was moderately successful for plutonium. For 6-phase plutonium, only one element out of the eight predicted to be extensively soluble was known to be almost insoluble, and of the sixteen elements predicted to have more restricted solubility, five were known to be essentially insoluble. The success of discerning solubility in the E phase by this method was comparable. One prediction made on the basis of this analysis was that the heavier rare earth metals, such as holmium, erbium, and thulium, should be soluble in the 6 phase, whereas the lighter rare earth elements, such as lanthanum or

Jan 1, 1963

By B. C. Craft, Murray F. Hawkins, John R. Rayne

A reservoir mechanism of sulfur recovery by the Frasch process is presented. Improving the economic, of recovery appears to be largely a well, rather than a reservoir problem. A most important factor is the limitation of the lateral extraction of .sulfur about the wells due to the almost vertical .flow of the injected hot water. Model studies are described which confirin the mechanism of sulfur recovery by presently used methods. Studies on a five-spot system indicate improved econo171ics regarding recovery, recovery rate, therinal efficiency, and well spacing. INTRODUCTION Sulfur mining by the Frasch process is one of the most important methods of sulfur production. Developed by Herman Frasch in 1894, it enjoyed a rapid growth and presently supplies 40 per cent of the world's sulfur and about 80 per cent of the U. S. sulfur." The Frasch process of mining the underground native sulfur deposits involves melting the sulfur in place by introducing super-heated water into the sulfur bearing formations, and producing the sulfur as a liquid. Many problems are encountered in mining these native sulfur deposits, and sulfur production depends chiefly upon the nature of the sulfur deposit and the underground thermal efficiency of the heat transfer system. THE RECOVERY MECHANISM Sulfur is typically found in salt dome cap rock as crystal aggregates occurring within the cavities, seams, and pores of limestone and gypsum formations.' Sulfur-bearing limestone is typically cavernous, vugular, and fractured. Porosity averages about 20 per cent and sulfur saturation averages approximately 25 per cent by weight.1,15 Vhe sulfur bearing formations are very heterogeneous in nature and physical characteristics vary widely within small distances. Total cap rock thickness may vary from 50 to more than 1,000 ft, and net productive thicknesses from a few feet to a few hundred feet. In most cases the upper portion of the limestone formation is barren of sulfur, varying from 5 to 200 ft in thickness.1,15,33 The immediately overlying sediments and the underlying dense anhydrite formation provide permeability barriers to the flow of water from the cap rock section.'" Sulfur wells are drilled with conventional oilfield drilling rigs. Fig. 1 illustrates the casing program of a completed sulfur well. The cap rock sections are drilled with core bits and continuous core logs are recorded. After coring, the cap rock section is underreamed to a diameter of 9 7/8 in. The bottom of the 8-in. casing is welded closed and rests on the bottom of the drill hole, which extends through the cap rock to a few feet above the bottom of the sulfur-bearing formation. The 8-in. pipe contains 5 ft of 3/4-in. perforations on 6-in. centers and 15 ft of 1-in. perforations on 1-ft centers. The 20-ft perforated section is set opposite the lower 20 ft of the sulfur-bearing formation. The 4-in. sulfur pipe is set inside the 8-in. water line on a seat ring at the top of the 5-ft section of 3/4-in. perforations. The mining water, heated to about 330°F under a pressure of 250 psi, is forced down the annulus between the 8-in. and 441-1. pipes and through the 1-in. perforations to the sulfur-bearing formation. Compressed air, at 400 psi pressure, is supplied through a 1-in. air line near the bottom of the well to provide air-lift of the liquid

Jan 1, 1957

By W. B. Gogarty

With flow of non-Newtonian fluids in porous media, effective viscosities are needed for use in the Darcy equation. These viscosities depend on the rock parameters and flowing conditions. In this investigation, rheological and flow results were correlated to develop an expression for calculating effective viscosities. Surfactant-stabilized dispersions of water in hydrocarbon were used with consolidated sandstone cores of different permeabilities. The average shear rate in a core was related to the permeability and porosity of the core and the frontal velocity through the core. By using the correlation obtained for determining effective viscosity, experimental and theoretical values were compared for each fluid system by determining average and maximum errors. For the fluid system showing the largest average error, the correlation fit 38 experimental points with an average and maximum percentage error of 4.3 and 14.8, respectively. For the fluid system showing the least error, average and maximum percentage errors of 1.8 and 4.3, respectively, were calculated using 29 experimental points. INTRODUCTION Use of non-Newtonian fluids in the petroleum industry is not new. Fluids of this type have been used for many years as fracturing agents and drilling muds. Recently, attention has focused on the use of high molecular weight polymer solutions for secondary recovery. Results have been reported on studies relating to the flow behavior of polymer solutions in porous media.1-4 Each study gives the viscosity in the Darcy equation as a function of the rheological properties of the fluid, the characteristics of the porous medium and the pressure gradient. The functional forms of the reported expressions differ somewhat in each study. The first three studies used unconsolidated porous media while the fourth used a single consolidated core. Because of the limited information available on the flow of non-Newtonian fluids in porous media, further investigation was undertaken in this area. We selected non-Newtonian fluids that did not contain high molecular weight polymers in order to minimize core plugging. The over-all objective was to gain a better understanding of the flow behavior of non-Newtonian fluids in consolidated porous media. Specifically, our goal was to determine the relationship between the average shear rate in a core and the frontal velocity. Because of this goal, it was necessary to determine the effect of permeability on the shear rate-frontal velocity relationship. We wanted to replace the viscosity in the Darcy equation with an expression relating to the average shear rate in the core and the rheological properties of the non-Newtonian fluid. THEORY For a time-independent, non-Newtonian fluid, the apparent viscosity is a function of the shear rate. This relationship is given by µ = F(v')...........(1) With Eq. 1, a single value of shear rate determines the apparent viscosity at that shear rate. With flow in porous media, a spectrum of shear rates occurs at any average throughput. An average shear rate v' can be used to represent the spectrum of shear rates that exists within the core. By using v' and the rheological data given by Eq. 1, an effective viscosity is determined for the flowing fluid. If v' is the correct average, µe becomes the appropriate viscosity for use in the Darcy equation. Under these conditions, flow rate-pressure drop relationships can be determined for non-Newtonian fluids. HOW the correct average shear rate might be related to the frontal velocity through the core and the characteristics of the porous media will now be considered. Later, the experimental data are presented that indicate the validity of these

By C. R. Claus, G. A. Standish

Since March. 1945, the Magnolia Petroleum CO. has drilled 39 wells in Southwest Coastal Louisiana. All wells were drilled within a comparatively small radius, but the area provides a large variety of problems. The deepest well drilled was 13,518 ft, and the total depth averaged 10,977 ft. Throughout this period drilling mud control and types of mud handled were: (I) phosphate, (2) red lime (late conversion), (3) red lime starch (early conversion), (4) red lime starch oil emulsion, (5) precision controlled low alkalinity-low lime content. and (6) gel muds for completion purposes. Improvement has been obtained in effecting some or all of the following: (I) more rapid penetration, (2) reduction in drilling hazards, (3) better evaluation of cores and logs, and (4) better completions. The geological sequence of zones penetrated range from recent sediments at the grass roots through the Frio section. Anticipation of high-pressure zones and incompetent formations entails precision control of drilling mud weights, and the unconsolidated nature of the various zones requires constant attention to the filtrate, viscosity, and gel strength values. In the Chalkley field, particularly, this combination of problems exists, where the formation pressures and overburden weight density values are in very close proximity. Design of casing and drilling mud programs must be modified to fit each well. INTRODUCTION Field and research work on drilling fluids has made constant progress, enabling operators to prospect progressively deeper horizons. Numerous papers have been written on the theoretical aspects of drilling fluid devel- opment, but in the field engineers have found it difficult to evaluate the role of specific mud constitutents when dealing in terms of thousand barrel mud systems. For that reason field data is somewhat lagging in technical report writing. However, applications of new techniques in the field have usually paralleled, and in numerous instances preceded, research work. The information obtained by Magnolia Petroleum Co. in the course of drilling 39 wells within a comparatively small area in Southwest Coastal Louisiana provides an excellent opportunity of reviewing a specific example of drilling mud evolution. A large variety of problems has been coped with, the most important result being that every well was successfully drilled to its projected total depth. The discussion begins with the advent of deep drilling in this area in March, 1945, and is concluded with a resume of recent drilling operations in the Chalkley field. The primary purpose of this paper is to describe the evolution in types of drilling fluids as it occurred and its application in the solution of various drilling problems. All of this information and experience resulted in the successful drilling of the three wells in the Chalkley field, where a combination of the most sound techniques was necessary in carrying drilling operations to the projected total depths. Other operators along with service company engineers have contributed considerably through the interchange of ideas and information to this paper, but the data and conclusions which are contained are based on first-hand observation of Magnolia Petroleum Company's drilling operations. The 39 wells drilled by Magnolia Petroleum Co. average in depth 10,977 ft per well, while the maximum depth penetrated was 13,518 ft. The cost of drilling fluids have varied from $8,700 to $165,000, with the over-all drilling costs ranging from $74,000 to $543,000 per well. This wide variance illustrates the unpredictable nature of each well and the effects on over-all cost when high density muds are required to control

Jan 1, 1955

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By E. W. Davis

About a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½-in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about 100 per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½-in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2½ kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1947

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By R. B. Porter, R. P. Porter, R. A. Lothrop

Changes became necessary in dredging methods employed in Idaho through passage of the Dredge Mining Protective Act (1954). Among other provisions, the law requires dredge operators to construct settling ponds of sufficient capacity and character to reasonably clarify the water used in the mining process before such water is discharged into the stream. Porter Bros. Corp., a placer mining company with many years operating experience in Oregon and Montana, became interested in strategic mineral placers in Idaho in 1950 when it was learned that prospectors had discovered a radioactive mineral deposit in Bear Valley Creek, 95 miles northeast of Boise. The company acquired mining leases and proceeded with exploration and development work on the property. After extensive research had resulted in the determination of successful separation processes, contracts were negotiated with the federal government and deliveries of columbium-tantalum and uranium concentrates commenced in 1956. The mining operations are located in a primitive area of Idaho among salmon spawning grounds and crystal-clear mountain trout streams. To avoid involvement in a very controversial issue, it appeared advisable for the company to develop water treatment procedures exceeding those requirements stated in the Idaho Dredge Mining Protective Act. Operation: The company operates one 6 cu ft continuous bucketline dredge and one 4 1/4 cu ft continuous bucketline dredge on the property. The dredges are jig-equipped, with feed being screened to 3 in. by trommels. The screening and gravity concentration methods satisfactorily separate the heavy minerals from companion clays, sand, and gravel. However, this separation of the heavy minerals requires water from the dredge pond with a minimum content of silt and colloids; therefore, water for dilution is added continuously to the dredge pond to suppress solids buildup. Discharge of this highly turbid water to maintain the proper pond level would ultimately result in an excessive silt load in Bear Valley Creek. To prohibit the turbid pond water from flowing directly into Bear Valley Creek, it was necessary to isolate the dredging area. Main by-pass canals were constructed along each side of the dredge pond and numerous secondary canals were dug for diverting seepage and snow runoff. One by-pass canal, extending more than two miles along the west side of the valley, diverts the main stream as well as tributaries entering from the west; a canal east of the dredge area diverts streams entering from that direction. At the beginning of operations in 1956, the dredge pond effluent was filtered through tailings and settled by use of coagulents in a series of lagoons. The filtrate was then discharged directly into the stream. Although this procedure gave satisfactory results in conformance with the state law, ice buildup and lagoon freezing hindered the efficiency of the process during periods of low temperature. For this reason, testing began in 1956 on a water treatment process that would operate efficiently under the extreme weather conditions encountered in Bear Valley. Development of Water Treatment System: Porter Bros. Corp. established the following requirements for effective continuous treatment of dredge pond effluent to the stream which, at low flow conditions, effluent to the stream which, at low flow conditions, would not result in a turbidity exceeding 25 ppm in the stream, 2) produce a sludge sufficiently dense to minimize disposal area requirements, 3) be semi-portable to follow dredge movements, 4) be capable of operating at low temperatures, and 5) be capable of handling a variety of capacities and turbidities.

Jan 1, 1961

By I. W. Alcorn

The cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 121/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8 -in. surface casing and digging a 7 3/4 - in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 It., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. AS opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By I. W. Alcorn

The cost of drilling in the past few years of proration and ever decreasing allowables has received increasing thought and study. It seems to parallel the strides made with respect to pumping problems in 1932 and 1933. Low profit margins stimulate the search for economies. Any discussion of slim-hole drilling involves a multitude of abstract values, and the problem can be attacked only by a study of records and rational thinking. In a measure, traditional methods must be studied with a questioning attitude. The words "slim hole" may be somewhat misleading, as the term is entirely relative. For that reason I wish to define it as used in this discussion. On the Gulf Coast, I would define a normal hole as one in which 10 3/4-in. surface casing has been set and below which a 9 7/8-in. hole is dug. With this as a datum, holes of larger diameter below surface would be called "large holes," with 121/4 in. as the "extra large" class and holes of smaller diameter classed in the slim-hole range, 6 1/4 in. representing about the minimum size. The optimum size has not been definitely determined, but the preference is for a program that would call for setting 8 5/8 -in. surface casing and digging a 7 3/4 - in. hole. Different sections of the country might very properly deviate from this practice because of differences in depth, formations, regulations, or other factors. This paper will be confined to a discussion of the drilling of exploratory wells, as the drilling of this class of wells is quite a different problem from that of drilling a proven field, although many of the same considerations apply in both cases, as will be apparent. Although for many years shallow slim-hole and core-test holes of small diameter had been dug, it was not, I believe, until the fall of 1937 that serious consideration was given to its application in drilling wells 7000 ft., 8000 ft. and 9000 ft. deep on the Gulf Coast. This does not mean that nearly all such wells drilled on the Gulf Coast now are of the slim-hole variety, but only that efforts have been aimed in that direction with very encouraging results and there has been a very definite trend to reduce the size of holes, a trend that probably will continue. As to exploration policy, there appear to be two distinct and opposite views. The one usually followed in the past was more or less designed to "shoot the works" on one well. Generally on the Gulf Coast, the depth at which production might be obtained is limited by the drilling equipment and economics. With this thought in mind, wildcat wells are often planned with the idea of carrying the depth to 10,000 It., or even 15,000 ft. All of the possible hazards are anticipated and the general drilling and casing programs are so predicated. Such wells contemplate the drilling of large-diameter holes; the setting of at least one protective string of casing and an extensive coring policy, all of which finally adds up to an expensive well. AS opposed to this general policy is the slim hole. This, on the Gulf Coast, recognizes that new discoveries represent gam-

Jan 1, 1941

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

By M. B. Bever, A. B. Michael

THE structure of cast A1-Si alloys is altered profoundly by modifying agents. Sodium, in particular, reduces the size of the silicon particles in the eutectic and tends to change their shapes from plates to nearly rounded grains. This refinement is accompanied by a shift of the eutectic to higher silicon concentrations and lower temperatures. Similar effects can be attained by rapid solidification. Hypotheses advanced to explain modification have involved the formation of a ternary eutectic,1 the removal of oxides by fluxing,' and even a presumed allotropic transformation of silicon. Other hypotheses assume that the modifying agent causes an envelopment of the silicon particles by the aluminum-rich solid solution, but attribute this envelopment to different mechanisms. According to various explanations, the growth of the silicon particles is obstructed by an immiscible sodium-rich liquid," an adsorbed layer of sodium,' or a ternary compound;5 his obstruction has been conceived as purely mechanical or as a colloidal action.' It has also been proposed that sodium reduces the surface tension on the Al-Si interface, thus permitting the aluminum-rich solid to grow faster and to envelop the silicon particles.? Still other hypotheses stress undercooling and the attendant change in the rate of nucleation of silicon, but fail to ascribe any definite function to the sodium addition." '" Procedure High-purity alloys of aluminum and 3 or 7 pct Si were treated with modifying agents containing radioactive sodium tracers. The experiments were intended to investigate the partition of sodium between the primary aluminum-rich solution and the eutectic, and, if possible, to determine whether sodium is concentrated in or around the silicon particles in the eutectic. Radioactive sodium fluoride, alone or mixed with stable sodium chloride, was allowed to react with the alloy for 5 min immediately before solidification in the crucible. Modification could not be attained with additions of less than the equivalent of approximately 0.1 pct Na. Some alloys were not completely modified, but comparison of the structures of treated and untreated specimens indicated a very considerable reduction in particle size of the silicon in all of the former. A treated alloy is shown in Fig. 1. Radioactive sodium fluoride was prepared by bombardment with deuterons having an energy of 14 mev. This bombardment (totaling, for example, 6 microampere-hours in one run) produced radioactive Na24 (half-life 14.8 hr) by the reaction 11Na23 (d,p) 11Na24. The radioisotopes of fluorine also produced have short half-lives and were not detected. A half-life determination by counting confirmed that the measured activity was due to Na24. The distribution of the sodium in the solidified alloys was determined by an autoradiographic technique by which a suitable stripping film is attached to a very thin metallographic specimen. After exposure and development, this emulsion remains superimposed on the specimen and may be examined microscopically or photographed by reflected light. The emulsion of the autoradiograph can be correlated directly with the underlying surface by simple adjustment in focus. The details of this technique have been described elsewhere." Results Fig. 2 is a micrograph of the autoradiographic emulsion ("autoradiograph") lying directly above the area of eutectic in Fig. 1. Fig. 3 shows a similar autoradiograph of a region consisting of primary solid solution. The small black dots (tracks) in these autoradiographs are developed grains in the emul-

Jan 1, 1954

By H. R. Stahi

THE ore of the Southeast Missouri lead district consists essentially of galena in dolomitic limestone. The galena usually is in a very finely disseminated condition. The experience of recent years in the concentrating plants of the St. Joseph Lead Co. has shown that dry crushing carried to a point where about 90 per cent of the ore passes a 14-mesh screen liberates the larger portion of the galena, and minimizes further necessary reduction in rod or ball mills. Concentration practice has attempted to carry size reduction to a point where economic unlocking of the galena is obtained, without causing undue sliming of the very friable galena. While 60 per cent of the tonnage of the district is treated by the flotation process, only 40 per cent of the total concentrates is produced by that means, as efforts have always been made to keep the grade and tonnage of flotation feed as low as possible. The milling practice of the district for some years has recognized the generally accepted idea of better selective grinding in rod mills as compared with ball mills, with the attendant decrease in production of fines. The function of rod and ball mills in the various concentrating plants is the grinding of table middlings and coarse tailings that carry lead values too high to be discarded. The simplified flowsheet in Fig. I illustrates the place of grinding mills in the circuit. The arrangement of classifiers, tables and mills constitutes a closed circuit within somewhat flexible limits. In 1937 experiments were conducted in replacing the ball charge in a 6 by 4-ft. ball mill with rods 2 in. in diameter and 51 in. long. This step was taken with some hesitancy, as it was easy to picture a mass of tangled and crossed rods. However, no difficulties developed, and after a short trial period, six more ball mills were converted to rod mills. These mills are of the spur gear and pinion, belt-driven type, using in most cases a 75-hp. motor and having a 9 1/2 -in. open trunnion discharge. As ball mills, they carried a charge of 16,000 to 20,000 lb. of balls, 2 in. in original size. The feed to the mills was dewatered by dewatering wheels and introduced at 70 to 75 per cent solids, with a single scoop feeder. One change in mill design was found advisable when rods were introduced. The existing end liners had an outward flare of 3 ½ in. in 12 in. These were replaced by linings having vertical interior faces, in order to prevent undue end travel of the rods. This change gave an effective working length of 5 2 ¾ in. inside the mill. No alterations were made in the shell liners, which are of the smooth type, made of manganese steel 2 in. in original thickness. The rods at present in use are 51 in. long and 1 3/4in. in diameter. The composition has been varied at times; at present they contain 0.70 per cent carbon and 0.70 per cent manganese. Some breakage and etching occurs as the rods become small, but this is considered preferable to using softer rods, which may kink and cause tangling of the charge. The mill charges are renovated occasionally, broken pieces being removed and the charge brought up

Jan 1, 1945

By H. L. B. Gould, Jr. Wenny D. H.

TO date there has been but limited interest in alloys of 80 to 95 pct Co and Fe with or without other additions. In 1932, S. R. Williams' reported practically zero magnetostriction for the 90 pct Co-10 pct Fe alloy. This same composition was used for pole pieces to control the magnetic field in magnetrons operating at high temperatures.' In 1947, a 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn composition was investigated3 for use in ballast lamps because of its high temperature coefficient of resistance. Recently, as part of a survey of ductile and malleable magnetic alloys capable of being processed to thin gages for possible applications in memory devices, the high Co-Fe alloys have been re-examined to determine their fabricating and magnetic characteristics. Alloys from 80 up to 95 pct Co and Fe with and without additions such as vanadium were prepared. In general these all had excellent ductility and malleability. Wire was drawn to thin gages without difficulty and fine hard-drawn wires flattened to 2) The phenomenon may have potential in estimating the carbon content of molybdenum. A given solution-treating temperature and cooling rate could perhaps be calibrated so that the area fraction of surface covered by carbide could be interpreted in terms of carbon concentration. By segregating to the surface, a big "magnification" of the carbon content is obtained, which should make the method cheap, direct, and sensitive and, therefore, perhaps of interest to the molybdenum industry. This work was conducted at Battelle Memorial Institute. Financial support by the Aeronautical Systems Division, United States Air Force, under Contract No. AF 33(657)-7376, is gratefully acknowledged, and the writer is thankful for the experimental assistance of Miss Marjorie Cantin. ribbon without splitting. Similarly, strip was cold-rolled as much as 99.75 pct reduction to a 0.25 mil thickness without intermediate anneals. Samples of round and flat wire and foil, in the severely cold-worked and annealed states, were checked for magnetic characteristics. The alloys exhibited widely divergent magnetic characteristics depending on the processing and heat-treating procedures used in preparing the samples. Direct-current hysteresis loops showing the different magnetic characteristics of 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn alloys are shown in Figs. 1 to 8 inclusive, while Figs. 9 and 10 show the loops for an alloy of 82 pct Co, 11.75 pct Fe, 5.6 pct V, and 0.65 pct Mn. Figs. 1 and 2 show the high remanence and exceedingly square-loop characteristics of the hard-drawn wire and ribbon roll flattened therefrom. With the change in processing from roll flattening to flattening by drawing through flat diamond dies the resultant change in texture is accompanied by the drastic change in the shape of the loop as shown in Fig. 3. This skewed loop on annealing reverts to a more normal loop as shown in Fig. 8. The most unique loops are obtained with flat rolled strip. These are shown in Figs. 4 and 5. In the case of the hard-rolled material, Fig. 4, there is little change in induction until the magnetizing force reaches 50 oe. From 50 to 60 oe there is a sharp increase in induction to over 15,000 gauss, which for all practical purposes is saturation. The induction remains at a constant value while the magnetizing force decreases to 40 oe. At this point the

Jan 1, 1965

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

By Robert Mehl

THE Widmanstätten figures found in the steels have been long recog-nized and in some aspects carefully studied,1 especially as they occur in cast hypoeutectoid alloys. Aside.from the practical importance of the structures obtained in the steels by various heat treatments, a study of the characteristics of these figures is interesting because of the rich opportunity the system affords, to, obtain new data on the mechanism of segregation from solid solutions. This opportunity is twofold: first, by changing composition within the austenite range the proeutectoid precipitate may be changed from that of ferrite to that of cementite, thus offering the same opportunity for changing the type of precipitate while maintaining the same basic lattice as that afforded by the Cu-Zn alloys;2 and second, the eutectoid inversion leads upon drastic quenching to the formation of martensite, a Widman-stätten figure of unique interest from ;the crystallographic viewpoint, particularly in comparison with those formed on-slow cooling.3 We have, therefore, two types of structure to study: that formed on slow cooling of hypoeutectoid and hypereutectoid alloys, and that formed on quenching hypoeutectoid, eutectoid, and hypereutectoid alloys. For each of these types of structure we require the crystallographic plane in the mother austenite along which the precipitate forms (we shall see that the precipitates in these alloys are invariably platelike in form), and also the orientation of the precipitate upon this plane. Some of these

Jan 1, 1933