Search Documents

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2'3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936

By E. C. Harder

INTRODUCTION FEW mineral deposits have in recent years attracted such general and Widespread attention as the Brazilian iron-ore deposits, due mainly to the quantities of rich ore occurring here, in contrast to the ever-decreasing grade of ores shipped from many large producing iron-ore districts of the world. The general average grade of the iron ores shipped from the Lake Superior district' has decreased to approximately 50 per cent., natural, in recent years. The Rubio ore of Bilbao, Spain,2 in 1890 averaged 55.5 per cent. metallic iron, dried; in 1902, 52.8 per cent., While at the present time a large proportion of the ores shipped from Bilbao are obtained by reworking the old dumps. In northern Sweden, where large magnetite deposits have only in recent years been extensively developed, selective mining is even now necessary in order to obtain high-grade Bessemer ores. During the last two years the iron ores of Chile have attracted much attention on account of the activities of the Bethlehem Steel Co. and others in the Chilean iron-ore region. Many of these ores are of good grade, yielding 67 and even 68 per cent. metallic iron, but judging from the Writer's observations in this region a large proportion of them Will be found to he of non-Bessemer grade. The most important variety of iron ore in Brazil is hard, dense to specular hematite, occurring in Minas Geraes. A large number (89) of analyses of this type of ore have been averaged, 3 giving the following composition: Per Cent. Iron 69.65 Phosphorus 0.0125 Silica 0.24 Combined H,0 0.38

Jan 10, 1914

By A. C. Boyle

PaGE I. Introduction.........68 II. Location of the District,....... • 70 .. III. Stratigraphy...........73 Description of the Rocks.......73 Triassic Eruptives (Andesite Flows and Tuffs) ....73 Triassic Sediments (Shales and Slates)..75 Areal Geology ............75 Structure...-.......76 Folds............. 76 Faults..........79 Shear ...........80 Intrusives..........81 Alaskite Dike.........81 Andesitic Intrusion.......82 IV. PetrogRaphy of thE Rock Types......83 Andesite Flows.........84 Tuff 8...........84 Andesite Tuff........84 Rhyolite Tuff.....-.......85 Alaskite-Porphyry.......89 Andesite Dike........91 V. Description of the Mines......92 VI. Metalliferous Deposits ........ 95 Character of the Ores...........97 Mineralogy of the Ores.......97 Metallic Minerals.......97 Microscopic Character of the Ores...98 Secondary Enrichment....... 103 Genesis of the Ores ...........104 VII. The Sulphate Deposits.......109 Gypsum ..... HO Anhydrite......... ,... 110 Barite............ 110 Origin. with special reference to Gypsum....111 VIII. Summary.............. 113 IX. BIblYogRaphY.............114

Jan 1, 1915

By Henry G. Granger

Repeated failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes: excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would not readily move towards the intake; and, most important of all, closing of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently increasing the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which call be considered dredge-able, in which stones more than 12 in. in diameter are not frequently encountered. II. An Effective Suction-Dredge. In harbor-operations, much larger stones are handled by suction-dredges. The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe, gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Jan 1, 1910

By J. G. Thompson

OXYGEN, nitrogen and hydrogen are present in' practically all metals in one or more of the following forms: (1) molecular gas in blowholes or blisters, (2) combined in nonmetallic inclusions such as nitrides, oxides or silicates, and (3) in solid solution in the metal. Gaseous elements, in some of these forms, are encountered in practically all metals and alloys but possibly have received most publicity in connection with iron and steel. In fact, the entire steel industry depends upon the control of the oxygen content during the refining process, as well as in the finished material, and it was only after the adoption of the use of efficient deoxi-dizers such as manganese that the production of good steel with a low carbon content became possible. In normally clean, sound steel the amount of hydrogen is negligible and the amounts of oxygen and nitrogen vary from a few thousandths to a few hundredths per cent. However, many of the effects attributed(27,31,40,41,53,54,55.56,62) ? to the presence of these elements are important and at first glance appear to be out of proportion to the amounts of impurities involved. The presence of oxygen is believed to affect the solubility of carbon in austenite and ferrite and thereby to affect the structure of the iron or steel. Such properties as strength, hardness, ductility, elastic .limit, impact resistance, magnetic permeability, tendency toward caustic embrittlement, irregularity in carburization, the cutting life of, tools, certain corrosion phenomena, the presence of flakes, seams, bands, ghost lines and hair cracks, and the tendency to age-harden, all have been attributed to the presence of oxygen.

Jan 1, 1932

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and re- quires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged be- cause a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced.

Jan 2, 1958

By T. F. McCormick

THIS year, 1950, is the golden anniversary of the construction and operation in this country of a tube mill for the sole purpose of fabricating aluminum alloy tubing. For a short period prior to the beginning of this mill, aluminum alloy tubing was obtained from foreign sources or produced in mills fabricating other metals. Indeed, it was a very short period because aluminum itself was a newcomer in the field of metals. The first sheet rolling mill had been in operation just eight years and a rod rolling mill for the production of wire and cable had been functioning one year. The first tube mill for aluminum was built by the Aluminum Co. of America in May 1900 and started production with four draw benches and five men, including the mill superintendent. The building itself was a lean-to attached to a sheet-rolling mill at New Kensington, Pa. The cost of equipment, including the draw benches, dies, mandrels, and other tools, was about $5000. This figure seems absurd in the present day but nevertheless it was questioned at that time whether or not such a large sum should be spent to embark on a new and uncertain venture. The initial production system for the new mill consisted of casting round hollow ingots in a tilting-type iron mold, reducing the ingots to bloom size outside the plant, and finally drawing to size on the draw benches. This method of producing aluminum alloy tubing survived just two years, as blooms of satisfactory quality were not obtained consistently. It was superseded by the cupping method in which a 24-in. diam circle cut from a rolled plate was formed into a tube bloom using first a small cupping press and then a push bench. It was stated that tubing so produced was limited to a maximum diameter of 2 3/4 in. and to wall thicknesses varying from 12 to 24 gage. However, for the first time all the operations were performed at one plant and the result was a quality product. Later larger cupping presses and push benches were obtained and the method continued to be the principal one for aluminum alloy tubing for almost a quarter of a century. During the interim the use of a Alan Mannesmann -type billet piercer was explored and it was used to some extent, but failed to produce consistently a smooth inside surface suitable for drawing with aluminum alloys. Experiments started during the latter stages of World War I in the production of tube blooms with a hydraulic extrusion press, led to the use of this type of equipment to make tube blooms for further drawing during a change-over period extending from 1925 until 1930. At this time the cupping method was discarded completely. From these humble beginnings, the aluminum alloy tubing business expanded until well over six million pounds were produced in a single month in the United States during World War II. The major portion of this production was in strong alloys which did not appear in the tubing picture until 1022, when 17S alloy tubing was introduced for aircraft construction.

Jan 1, 1951

By H. H. Stout

IN the early fall of 1925, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point, The apparatus consisted of a vertical 1-in. dia. silica tube about 12 in. long, heated on the outside, The cathodes were broken to pass a8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in, long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to i500° to 1600°F. and the gas treatments lasted from 3 to 6 hr, The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc, had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F," Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me."

Jan 1, 1940

By J. G. Thompson

OXYGEN, nitrogen and hydrogen are present in practically all metals in one or more of the following forms: (1) molecular gas in blowholes or blisters, (2) combined in nonmetallic inclusions such as nitrides, oxides or silicates, and (3) in solid solution in the metal. Gaseous elements, in some of these forms, are encountered in practically all metals and alloys but possibly have received most publicity in connection with iron and steel. In fact, the entire steel industry depends upon the control of the oxygen content during the refining process, as well as in the finished material, and it was only after the adoption of the use of efficient deoxidizers such as manganese that the production of good steel with a low carbon content became possible. In normally clean, sound steel the amount of hydrogen is negligible and the amounts of oxygen and nitrogen vary from a few thousandths to a few hundredths per cent. However, many of the effects attributed(27,31,40.41,53,54,55,56,62) ? to the presence of these elements are important and at first glance appear to be out of proportion to the amounts of impurities involved. The presence of oxygen is believed to affect the solubility of carbon in austenite and ferrite and thereby to affect the structure of the iron or steel. Such properties as strength, hardness, ductility, elastic limit, impact resistance, magnetic permeability, tendency toward caustic embrittlement, irregularity in carburization, the cutting life of tools, certain corrosion phenomena, the presence of flakes, seams, bands, ghost lines and hair cracks, and the tendency to age-harden, all have been attributed to the presence of oxygen.

Jan 1, 1932

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By Raymond Edmundson

BARITE probably was first mined in the United States in 1845, when a small deposit was operated in Prince William County, Virginia1. The next state to produce barite was Missouri, and according to Weigel2, mining began about 1860. Virginia was the leading producer during the early period of barite mining, but by 1893, Missouri was producing almost an equal amount3. From this date, Virginia, although not the leading producer, furnished large quantities of crude barite until oper-ations gradually declined about 1907. Since 1910, there has been only one producer in Virginia. It is not known when barite was discovered in each of the Virginia areas (Fig. 1), but it is reliably reported that mining on a commercial scale began in Campbell-Pittsylvania counties about 1874; Smyth County in 1877; and in the Russell-Tazewell area about 1890. Barite is widely distributed in Virginia, occurring in nineteen counties. The localities that contain material of some economic value have been grouped into six areas (Fig. 1), each designated by the county or counties in which the barite is found. As many of the smaller areas show a similarity in geologic occurrence, they will be considered in this paper as two major groups; namely, Appalachian Valley and Piedmont Province. The first group, which includes the barite deposits of Russell, Tazewell, Smyth, Botetourt and Roanoke counties, lies northwest of the Blue Ridge and its foothills and southeast of the Appalachian plateaus. The other group includes deposits from the Blue Ridge on the west to the western margin of the Coastal Plain, in Campbell, Pittsylvania, Bedford, Grayson, and Fauquier counties.

Jan 1, 1936

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By Fred A. Anderson, George B. Wallace, Edward J. Slebir

As the reservoir rises behind an arch dam, it presses the arch into the canyon walls and valley floor. To compute the stresses, deflections, and arch reactions, it is necessary to know how much the rock deforms under the combined loads of gravity, temperature, and water. Under sustained loading for a period of time, the rock continues to deform or "creep" slightly, causing changes in the stresses and shape of the arch. Under reduced loading, the elastic arch tends to resume its unstrained position and it is important to know that the rock will follow it and maintain tight contact along the abutment. It is, therefore, important to know the "set" characteristic of the rock. Past attempts to define load-deformation properties of rock, including creep and set, have largely l been limited to laboratory test of intact cores and in-situ jacking test utilizing bearing plates 2 to 3 ft in diam. In both cases, a uniaxial load has been applied to a volume of rock too small to fully reflect the influence of cracks, joint systems, foliation, and other inherent weaknesses within the rock mass. This chapter describes a large radial jacking test which more nearly duplicates the action of an arch dam by penetrating the load deep into the rock mass, bringing into play more of the factors which contribute to prototype deformation. Results obtained from the large radial test are compared with those from smaller uniaxial test. DESCRIPTION OF RADIAL TEST The radial jacking test described in this chapter was performed in an adit off of an exploratory tunnel driven into a proposed dam abutment

Jan 1, 1972

By W.C Ellis, Earle E. Schumacher

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By Earle E. Schumacher, W. C. Ellis

Nonferrous alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,' nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By J. J. Egan, A. B. Kinzel, W. Crafts

Advances in the production of quality steel have emphasized the need for greater knowledge of the amount and distribution of oxygen in the steel. Control of inclusion content and quality is largely dependent on such knowledge. While many analytical methods have been devised for the accomplishment of this end, few are without serious limitations in accuracy, convenience, or skill required in application. Usually at least two methods are necessary to determine total oxygen and constituent oxides. Because of the great importance of this problem and the specific interest in the application of such methods of analysis, the various procedures were carefully reviewed at the Union Carbide and Carbon Research Laboratories, with the view of developing a method free from the limitations mentioned above. Intensive experimentation finally led to an improved iodine extraction analysis described by Cunningham and Price.1 After this had been thoroughly checked from the standpoint of the analytical chemist, it was rechecked from that of the metallurgist. This involved preparation of a number of small heats of varying composition with determination of total oxygen in the molten metal by the alumina method2 and an analysis of the solidified material without the aluminum addition by means of iodine extraction; the oxides of iron, manganese, silicon and aluminum also being determined by the iodine analysis. The report of this work constitutes the subject of this paper. The Iodine Method Fundamentally the iodine method is well established. It is based on the procedure first described by Eggertz3 and depends upon the fact that iron, manganese, silicon and aluminum, as well as the metallic constituents of the pertinent sulfides, carbides and nitrides of these metals

Jan 1, 1933

By W. F. Holbrook, C. E. Wood, E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and .its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. TYPES OF FURNACES Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1938

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

By Donald E. Garrett

The processing of brines from Searles Lake, California, yields one of the world's largest supplies of borax and boron chemicals, second probably only to the massive deposit at Boron, California. Two companies produce from this deposit, the American Potash & Chemical Corp. and the West End Chemical Co., a division of the Stauffer Chemical Co. Two processes are employed in recovering borax from the brines; one is used by both companies and consists of carbonating the brine to form sodium bicarbonate, removing this, and then cooling the liquor to crystallize a crop of borax. Only American Potash uses the second process, evaporating the brine to concentrate it and remove (crystallize) much of its NaCl, Na2CO3, Na2SO4, and NaLi2PO4 content, quick cooling the remaining liquor to remove KCI, and then seeding the filtrate to remove borax. Both methods will be briefly described. Searles Lake is a large evaporite body formed during the most recent two Sierra Nevada ice stages, the Tahoe and the Tioga. Runoff waters from the Sierra Nevada Mountains collected in the large Owens Valley drainage basin and from there overflowed into the Indian Wells basin and then into Searles Lake. In each Lake, evaporation took place. To a large extent the Owens and Indian Wells lakes acted as settling basins, for much of the mud, and insoluble calcium and magnesium precipitates were deposited there. Recent volcanic activity in the mountains to the north and east of Owens Lake had scattered considerable mineral-rich volcanic ash and debris throughout the drainage area, and several hot springs were formed that contained boron and other salts. The present flow rate and concentration of several springs, and the known age of at least the Tioga zone, can fairly well account for all of the boron present in Owens and Searles Lakes.1 The tungsten content can be accounted for in a similar manner.2 Most of the salts thus originally present in the fresh water runoff-from ice, snow, and rain-accompanying these two ice stages were ultimately deposited in Searles Lake. During the Tahoe period, from 25 to 40 ft of massive, mixed salts were deposited, along with six interspersed layers of mud (four inches to two feet thick) representing comparatively brief interglacial periods. Before the final desiccation of the lake, from 10 to 14 ft of new mud was deposited, representing the Tioga stage. The crystals subsequently deposited were from 70 to 90 ft thick, and form the present lake surface. The extent of the salt body is about 34 square miles, of which 12 square miles are exposed salt; the remaining area is covered by recent alluvial deposits (chiefly mud). The present lake is generally dry on the surface but floods to a shallow depth following heavy rains. The crystal body of both zones consists of continuous clusters of salts, and the voids between crystals (about 45 pct of the total volume) are occupied by brine. The level of this brine never recedes more than several inches below the salt surface. The brine pumped to the plants for processing is generally saturated with all of the solid phases present in that area, and thus is a complex mixture containing about 35 pct solids (see Table 3). The brine composition varies somewhat at different areas of the lake and from upper to lower structures, so wells are drilled in the areas and to the depths desired. A casing is cemented in the hole to within a short distance from the bottom, and pumps with about 14-ft suctions are mounted on the casing to pump the brine into the plants. The evaporation process of the American Potash & Chemical Corp. treats upper structure brine, evaporating all of the water from

Jan 1, 1960