Search Documents

By George A. Morrison

The Columbia Chemical Division of the Pittsburgh Plate Glass Co. is at Bar-berton, Ohio, 35 miles south of Cleveland. For many years large tonnages of limestone have been brought to the Barberton plant from distant points. The stone is here burnt in vertical kilns, the resultant product then hydrated and the hydrated lime used in chemical processing. To eliminate the expense of these shipments, the company decided to investigate a limestone bed known to exist on company property at Barberton, where the stone is used. The bed lay at a depth of more than 2000 ft. and was known locally as the "Deep Lime." Chemical analyses of sludge from churn-drill holes made some years ago proved that the limestone was of sufficient purity to warrant diamond-drill exploration. Four diamond-drill holes were put down at well-spaced intervals, to represent fairly an area of four miles by one mile. Cores logged as to chemical and physical conditions were found to compare closely, and to corroborate the earlier evidence that the limestone was of superior quality for chemical use. A plant of 300 tons per hour was subsequently decided upon. SITe The yard at the chemical plant was already so congested that location of the projected mine within its area could not be considered. Eventually a site was selected 2 miles northwest of the plant, near the main line of the Erie Railroad. Here 412 acres were owned outright by the company and stone rights were obtained on 2 50 additional acres. This location required a transportation line of nearly 2 miles (8800 ft.), crossing two major highways, and to avoid interruption of deliveries to the plant, overpasses were planned. Geology The limestone in the immediate vicinity lies about 2200 ft. below the surface. Geologists* identify this stone as Delaware of Devonian age. It is overlain by 18 ft. of unconsolidated (sand and gravel), 100 ft. of water-bearing sandstone, and finally 2080 ft. of shale into which sandstone in thin layers is interbedded. The contact of shale and limestone is abrupt, flat-lying and very pronounced. Berea sandstone, often found at 520 ft., is absent, but Euclid sandstone was encountered, together with a seepage of oil and a small amount of methane gas. The limestone bed itself is 345 ft. thick, and overlies 200 ft. of gypsum. The lower part becomes dolomitic as it approaches the gypsum. A detailed study of the drill cores indicates that the upper 50 ft. are highest in lime and reasonably low in silica. The physical make-up shows several separating cherty layers. These occur at definite horizons and cause distinct partings, which become horizontal planes of

Jan 1, 1946

By Arvid Anderson

THE weathering of copper-bearing ores with the formation of a water-soluble salt and the recovery of the metal by leaching and evaporation or precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 lb. of copper at an average operating cost, to date, of 3.85 cents per pound at the company's workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 lb. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted.

Jan 9, 1925

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967

By Charles R. Keyes

Prefatory,........323 Foundation of classificatory schemes in general..325 Past opinion on the classification of ore-bodies,.326 Nature of ore-deposits,....... 326 Definition........326 Fundamental law of origin.... 327 Significance of ore-bodies,.... 327 Date of origin........328 Original source of ores..... 328 Alteration of ore-bodies,....329 General methods of ore-formation.... 330 Ascension verm lateral secretion... 330 Replacement.......330 General factors in classification....332 Genesis in ore-classification....332 Literature of ore-deposits...... . 333 Criteria of ore-classification,..... 335 Primary grouping of ore-deposits..... 338 Hypotaxic deposits......341 Eutaxic deposits...... 341 Ataxic deposits....... 313 Secondary categories of ore-bodies....343 Ternary phases of ore-deposition.....344 Types of hypotaxic or surface deposits..... 344 Illustrations of eutaxic ore-bodies.... 347 Examples of ataxic ore-bodies.....352 Recapitulation.. .. .. .. 355 Prefatory. Much has been written on the genesis and classification of ore-deposits. Much remains yet to be written on the subject

Jan 1, 1901

By Archer Wheeler

THE copper industry in the Province of Katanga, in the Belgian Congo, which is now controlled and operated by the Union Minere du Haut Katanga, had its inception many years ago in the vision of a Scotsman, Robert Williams, now Sir Robert Williams, Baronet. He it was who personally negotiated the mineral concession with King Leopold of Belgium, sent in the prospecting parties who located most of the present mines of the company, later arranged for the Belgian participation from which the present company was formed, and has been its active mentor ever since. The idea back of his efforts was the establishment of an industry on the Congo-Zambezi divide, of sufficient importance to draw up to it the head of the Cape to Cairo Railroad, the dream of Sir Cecil Rhodes, and the consummation of which he had left as a legacy to Mr. Williams, his successor. The reports of the prospecting expeditions showed that copper in profitable quantity was there, but many difficulties lay in the way of the establishment of the infant industry. The isolated location of the mines, various tribal wars, the Boer War, and many other factors contributed to making progress very slow. However, in spite of these difficulties the railroad was finally built and a blast-furnace plant erected at Lubumbashi, near Elisabethville, the capital of the Province. Operations of this plant were started in 1911, treating high-grade oxidized ores and producing pig copper by a reducing smelting. Production has been continuous since that time and the company has grown so that at present it ranks as the largest individual copper producer in the industry. It is a fitting monument to the foresight, optimism and driving force of its founder, and the progressive policies of his Belgian colleagues. In January, 1914, the Union Miniere du Haut Katanga engaged as its consulting engineer, Archer E. Wheeler, metallurgical engineer, at that time general superintendent of the Great Falls plant of the Anaconda Copper Mining Co. Mr. Wheeler was commissioned by the Board of Directors to proceed into Katanga, and make all necessary investigations to enable him to report on a comprehensive development program, and to recommend a scheme of treatment particularly for their low grade

Jan 1, 1932

Jan 1, 1883

By H. S. Bell

IT SEEMS unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remarkable operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to theoretically analyze the partial-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9 B° North Texas crude.

Jan 1, 1928

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reasonable expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In-a bulk tonnage such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: l (1) by screening or sizing, (2) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing, while it is possible to produce a very acceptable product from mediocre cleaning if the coal is well screened and mixed.

Jan 1, 1950

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

Jan 1, 1926

By A. H. Jones

The Belmont mill at Tonopah, Nev., was designed and constructed by the Belmont staff. Ground was broken in August, 1911, and milling operation started July 25, 1912. The metallurgical flow sheet, and the machinery adapted 60 carrying out operations in accordance with this plan, were decided upon from experience gained in the treatment of Belmorlt mine ores at the old Belmont mill at Millers, Nev. The detail drawings were madc by the engineering staff of the Tonopah-Belmont Development Co., under the supervision of Otto Wartenweiler, who also had direct charge of the construction, consulting with the General Superintendent of the company, Frederick Bradshaw, and the writer.

Jan 1, 1916

By T. E. Tietz, J. E. Dorn

Activation energies for creep of copper at intermediate temperatures, where crystal recovery was negligible, were determined by the simple technique of rapidly alternating the test temperature between and T2 (T2 = TI + about 10°K) throughout a constant stress creep test. The activation energy for creep H was found to be 37,000± 3,000 cal per mol, independent of stress and strain. The same creep laws as have been previously established for high temperature creep were found to be valid for creep at intermediate temperatures. But the AH was found to be lower than that for self-diffusion in the intermediate temperature range whereas it is known to be equal to that for self-diffusion at high temperatures. IT is now well established that creep at high temperatures can be correlated by the functional relationship'-" e = f(?) s = constant [I] where E is the total plastic strain, f is the function that depends on the stress, ? = f e -- dt, t is the duration of test, e is the base of natural logarithms, AH is the activation energy for creep, R is the gas constant,T is the absolute temperature, and s is the stress. Thus, identical values of are achieved during creep under a given stress at two alternate temperatures at the same total strain. At the same strain therefore where subscripts refer to the two alternate temperature conditions of test. Consequently, the activation energy for high temperature creep is readily obtained with the aid of Eq. 2. Activation energies so obtained have been observed to be insensitive to the creep strain at which they are evaluated, the applied stress, grain size, minor alloying additions,'-' cold worked state, and the presence of thermally stable dispersions of intermetallic compounds in an a solid solution matrix Furthermore, the activation energy for high temperature creep is very nearly equal to that for self-diffusion in all cases where adequate data are available for comparison." " The apparent identity of the activation energies for high temperature creep and self-diffusion strongly suggest that high temperature creep arises from a dislocation climb process. This hypothesis is further strengthened by the fact that the energy of activation for high temperature creep is insensitive to the applied stress," and by the observations that the correlation suggested by Eq. 1 cannot be ex- tended to temperatures below those for rapid crystal recovery. When using the activation energy for self-diffusion, Eq. 1 fails to give the required correlations between creep curves at various intermediate temperatures.' This suggests that the dislocation climb mechanism for creep might be superseded by some alternate mechanism in the intermediate range of temperatures. This investigation was initiated in a preliminary attempt to ascertain the type of creep law that might be valid in the intermediate range of temperatures. Special consideration, however, was given to the determination of the activation energy for creep in this range because the Becker-Orowan', " and the Mott-Nabarro10 theories for transient creep suggest that the activation energy should increase

Jan 1, 1957

By F. F. Aplan

The past year has been another year of vigorous fundamental research in mineral processing as evidenced by the active publication of results, particularly in Germany, Japan, United Kingdom, United States and USSR. It was also noteworthy for several significant meetings and conferences. The Basic Science sessions at the AIME Annual Meeting continued to attract an increasing audience and the sessions were especially notable for the active discussion of papers. The third Engineering Foundation Conference on Particulate Matter Systems,1 chaired by F. F. Aplan, was held in Milwaukee in August and attracted over 100 experts from five continents. Sessions at this week-long conference covered comminution, particle characterization, separation of fine particles, fluid-solid separations as applied to pollution control, flotation kinetics, particle-particle interactions and particle agglomeration. This popular conference will be continued under John Karpinski of Bethlehem Steel Corp. as 1968 chairman.

Jan 2, 1968

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By S. J. Matas, R. F. Hehemann

The existence of two distinct forms of bainite—upper and lower bainite—in hypoeutectoid steels is confirmed by a systematic study of the structure of the product resulting from this mode of austenite decomposition. The transition between these two forms occurs at about 650° F regardless of the alloy content of the steel and their structural differences can be interpreted in terms of the kinetics of carbide precipitation from supersaturated ferrite. In the past few years, a renewed interest has been displayed in the kinetics and mechanism of the bainite reaction in steels. Several rather divergent models for the transformation mechanism have evolved from these studies,'-' however, it is difficult to evaluate these models critically on the basis of the existing experimental data. In particular, a more detailed knowledge of the structure of bainite should be helpful in providing a framework for the construction of an appropriate model. Metallographic studies7-l4 have led to a recognition of at least two distinct forms of bainite—frequently termed upper and lower bainite. Although the morphology of bainite changes with reaction tem- perature, there appears to be a relatively sharp transition between the two forms. This occurs in a narrow temperature range near 650° F. Transformation at temperatures below about 650° F results in the presence within the bainite of small plates of carbides oriented at an angle of 60 deg with respect to the direction of growth of the plate, while at higher temperatures carbides are oriented parallel to the growth direction. There is no generally accepted view regarding the significance of this structural transition. Some authors feel that carbides precipitate from austenite at all reaction temperatures1' while others claim, at least for low-temperature bainite, that carbides precipitate from supersaturated ferrite.14.15 It was recognized many years ago that the nature of the carbide in bainite depends on the reaction temperature. The carbide hase in upper bainite is unmistakenly cementite.16-19 The exact nature of the carbide in low-temperature bainite is less certain. Magnetic measurements of lower bainite reveal no cementite Curie point21'22 and dilatometric studiesz0 produce total expansions which are larger than those predicted on the basis of a ferrite-plus cementite structure. These effects have been attributed to the

Jan 1, 1962

By V. J. Kniazeff, S. A. Naville

The problem of unsteady-state condensate-gas flow through porous media leads to a set of second-order non-linear partial differential equations. Such a set of equations is numerically solved in the case of radial two-phase flow around a well, taking into consideration both the thermodynamical properties of the fluid and the mechanical properties of the reservoir. The fluid properties, reflecting the PVT relationship of the gaseous and liquid phases, are expressed by using the partial specific masses of the two main separator products in these phases. The flow properties of the reservoir rock are expressed by the generalized Darcy's law for the liquid phase and by a quadratic relationship between the rate of flow and the pressure gradient for the gaseous phase. The numerical solution of the equations for pressure and saturation US radius and time is worked out through programs written for a computer. The evolution of bottom-hole pressures, well productivities or- deliverabilities and effluent compositions with the depletion of the reservoir is easily derived. The application to the Saharian gas-condensate field Hassi R'Mel led to a better understanding of the drainage mechanism. A zone of fairly high liquid saturation develops around the wells, reducing the effective permeability, and represents a loss of condensible products in addition to the PVT-like retrograde condensation. lnside this zone, near the well, the deviation from Darcy's law for the flow of the gaseous phase governs the well deliver-ability. A back-pressure test has been computed and correlates with the field results. INTRODUCTION Two-phase flow of volatile hydrocarbons, like condensate gas or light crude oil, may be treated as the flow of a binary mixture by an arbitrary division of the chemical components into two groups. This is translated into two equations of mass continuity, which constitute a set of relation- ships for the pressure and the saturations vs the space coordinates and the time. The equations contain the laws governing the composition and the motion of the phases. The problem so defined is solved with the assumption that the compositions of the phases at any pressure are respectively the same as those observed in a PVT measuring cell under differential liberation. In a first series of computations, it was assumed that the flow obeys the generalized Darcy's law. A satisfactory representation of the retrograde condensation around the well was thus obtained. In addition, the trend toward decreasing effective permeabilities was obtained, and the computed composition of the effluent checked the laboratory values. However, it has not been possible within this basic assumption to represent the non-linear relationship between the production rate and the bottom-hole pressure drawdown as observed for gas wells in the field. Following the advice of A. Houpeurt it was decided to consider the relative permeability to gas as a function of the velocity of the gas Phase.1 The necessary physical determinations were made by E. COstaséque using a method devised by A. Houpeurt and R. Iffly. As numerical processing of the equations progressed, several difficulties were encountered which were overcome through collaboration with the computer manufacturer. This mathematical model of two-phase flow in porous media had been primarily intended for and extensively applied to the case of the Hassi R'Mel gas-condensate field, operated by SN Repal for SEHR, a joint subsidiary of SN Repal and CFP (A). The programs have also found their applications to forecast the behavior of several fields in the Sahara area containing light and volatile hydrocarbons. BASIC EQUATIONS We will consider a zone in the porous reservoir where the flow properties and the in situ composition of the fluids can be assumed to be uniform. A part of the equations of transient flow can be written with the specific gravity of the fluids being taken equal to the sum of the contributions due to the

Jan 1, 1966

By Irwin Roman

IT has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maxi-mum electromotive force will be devel-oped when the axis of rotation is perpen- dicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, FIG. 1.-MAGNETIC GRADIOMETER. it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the inten-sities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing and shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization—one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subsequently mineralized by sulphides and barite. Introduction Buchans is 5 miles north of Red Indian Lake, in Central Newfoundland, at an elevation of 900 ft. above sea level and 400 ft. above Red Indian Lake, and is reached by a 37-mile private railway from Miller-town Junction. The first ore body found at Buchans was discovered some 30 years ago in the bed of Buchans River, by Matty Mitchell, an Indian woodsman employed by the Anglo-Newfoundland Development Co. Ltd. In the years following the discovery the ore was developed by shaft-sinking and drifting, with results indicating a lenticular ore body in a shear zone, containing about 100,000 tons of extremely fine-grained sulphide ore in barite gangue averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn. Because a profitable metallurgical treatment for the ore was not found, the mine was closed down in 1911. In 1915, Mr. H. A. Guess, Vice President of the American Smelting & Refining Co., learned of the Buchans River ore body, and after metallurgical tests had been carried on from time to time in his company's testing plant a satisfactory separation of the sulphides by selective flotation was finally effected in 1925. Prospecting for additional ore bodies was begun in 1926, utilizing geophysical methods under the direction of Hans Lund-

Jan 1, 1937

By AIME AIME

CONVENTION plans for the A.I.M.E. Regional Meeting to be held on the Minnesota Iron Range Aug. 12 to 1.5 are being completed to give the visiting member?s from all parts of the country a wide variety of technical and recreational features. High spots of the social events are the official dinner, dance, luncheon and golf: and of course, special provision is being, made for the entertainment of visiting ladies. The technical sessions will fit in with scheduled trips to view all phases of mining, beneficiation and transportation of iron ore. Men from the West and Southwest will find much of interest in the detail of the mining operations. A trip to the steel plant of the

Jan 1, 1941