Search Documents

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955

By Lucien Eaton

THE changes that have occurred in metal mining in the past 75 years include almost everything that we know about modern mining. It is true that in odd corners of the world mining is still carried on as it was before that period, but in the United States such instances are rare. Everything has changed to some extent. Even picks and shovels have changed in design and materials. At the beginning of this period steam power had been used for pumping and hoisting for nearly 75 years, but almost every other operation underground was performed by manpower. Although mining was carried on in a small way east of the Appalachian Mountains before the Revolution, and continued thereafter on an increasing scale for more than 100 years, it was not until the discovery of the iron and copper deposits in Michigan and Minnesota and the opening of the mineral areas of the West after the building of the transcontinental railroads that the real development of modern metal mining began. In the same period many problems of deep mining in South Africa were solved by new techniques in shaft sinking and hoisting. Before this time knowledge of mining and skill in its performance were handed down from father to son by the apprentice system, and the son learned to do things in the way his father and grandfather had done them. The rapid expansion of mining in the United States after the Civil War required more men than the apprentice system could supply, and the

Jan 1, 1947

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon.' Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract. CONTACT ANGLE AND OIL ATTRACTION The contact angle-the angle formed by a fluid-fluid boundary when both are in contact with a solid-has been indicted several times for complicity in the phenomenon of flotation. This angle is supposed to indirectly measure the surface energy of a solid. Thus if we have two fluids in contact with a solid, we may express the difference between the two fluid-solid tensions as equal to the fluid-fluid tension times the cosine of the angle between the two fluids.4 If the two fluids are in contact with the solid, this is, no doubt, an excellent way of establishing relative surface energies. However, in flotation, we deal with substances which are not wetted by water. What assurance have we, then, that the angle

Jan 1, 1928

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By Russell Salter, Edwin J. King

SINCE 1950, when perhaps two or three cyclones were being tested in Arizona, the number in use has grown to about 100. Most of these have come into operation within the last two or three years, and according to information supplied by various mining companies, the number will continue to grow for several years more. In mills that have been recently constructed, cyclones dominate the fine classification field, removing grit from lime slurries, producing smelter flux, reducing concentrate thickener overloads, classifying molybdenite in grinding circuits, and conditioning flotation feed. Four major copper companies are now testing cyclones in primary grinding circuits, and one concentrator soon to begin operation will classify entirely with cyclones. In at least two instances these versatile machines have been given a vital role in the construction of tailings disposal systems.

Jan 8, 1957

By Dodge, C. E.

ONE of the first mining areas to be developed in Arizona was that in the district centering about Clifton and Morenci. Traces of metals were first noticed by Henry Clifton on an expedition in 1864. Definite copper outcroppings were also reported in the following year by General J. H. Carleton when he led his troops into the district on an Indian raid. Actual mining operations were started in the early seventies. and the first smelter was finished in 1873. Two adequately financed companies acquired most of the property, and both commenced production about 1882. These were the Arizona Copper Co.. owned by a group of Scotch investors, and the Detroit Copper Mining Co., afterwards purchased by the firm of Phelps, Dodge & Co. Later the Shannon Copper Co. acquired and operated a number of claims in the northern part of the district. These three companies all operated underground, mines independently for many years.

Jan 1, 1942

By William M. Bowron

Thirty years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone, colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation, either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. The Present Theory. Referring to this subject, Dana says :&apos; "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued.... The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, west and south, could not have been formed in an open sea; for clayey iron-deposits do not accumulate under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself, I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Jan 1, 1906

By Albert Sir Kitson

THE manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In. certain respects they strongly resemble those of India and Brazil, as contrasted with those of Tertiary age in Georgia. Viewed from the present condition of the maganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments; youngest are the products of decay and degradation with the concentration of manganese oxide of both areas. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate amount of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows largely of basic types. To this series I have given the name Birrim. Its age is unknown, for no definite fossils have been discovered in it. As the characteristics of these non-fossiliferous strata at many places are the same as those of strata in many parts of the world that are suitable for the preservation of fossils and that contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim series have normally a northeast-southwest strike and are folded, but not to any very great degree except in certain belts., From the Eastern Province of the Gold Coast they may be traversed across their strike for more than 600 miles to the extreme northwestern corner of the Northern Territories. Thence. they probably extend much further into French Territory.

Jan 5, 1927

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By J. Kent Smith

The object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent; furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575" F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450" F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450" F.) were reheated for varying periods of time at 575" F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By J. K. Stanley, R. F. Meel

The recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are emp1oyed.l Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystal- lization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress. 4,5 The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert mcasurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now available for the case of three-dimensional recrystallization (recrystallization of

Jan 1, 1942

By R. F. Meel, J. K. Stanley

The recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are emp1oyed.l Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystal- lization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress. 4,5 The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert mcasurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now available for the case of three-dimensional recrystallization (recrystallization of

Jan 1, 1942

By F. Twyman, D. M. Smith

Those chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates may be checked as often as desired. If, possessing these advantages, the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards 19cientific Paper No. 444. The Development of Analysis by Spectrogbaphy Fig. 1 shows, by means of photographs taken with a quartz spectro-graph, what a valuable region of the spectrum is excluded if one has a visual instrument only. Wave length 4023 is about the end of the visible spectrum, the region from 3800 to 1854 being invisible. It is easy to understand then how it is that the vigorous resuscitation of spectrum analysis which has commenced in the last few years has been associated with the use of the quartz spectrograph; notwithstanding that the most useful instrument for the general inorganic chemist to have at his elbow, after the balance, is a good visual spectrometer.(1) 1 The revival of spectrum analysis is to be attributed chiefly to the work of W. N. Hartley with his co-workers, and to A. de Gramont. Hartley,

By James S. Browning

For the past several years, USBM has conducted laboratory and continuous process development work on the weathered mica pegmatites ores of Alabama, Georgia, and North Carolina to determine the feasibility of recovering commercial-grade mica concentrates by flotation. The research has resulted in the development of two processes for flotation of mica: 1) an acid-cationic method for recovery of coarse mica and 2) an alkaline-anionic-cationic method for recovery of fine mica. The research indicated that the two processes may be effectively utilized separately or in combination for flotation of mica from weathered pegmatite ores. This report summarizes the process development work, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained mica. Mica mining in the United States is confined largely to pegmatites and schists in a few well-defined areas. The largest region extends from central Virginia southward through western North and South Carolina, northern Georgia, and east-central Alabama.&apos;" Whereas in western North Carolina, these pegmatite dikes are weathered to only a shallow depth, they are deeply weathered in the Carolina Piedmont and in Georgia and Alabama. Particularly in Georgia and Alabama, mica is found in the decomposed slates and schists adjacent to the pegmatites, and in deeply weathered granites. Most flake mica is obtained as the major marketable product by crushing and milling pegmatites4 To a lesser extent, mica is produced as a byproduct of feldspar" and spodumene. Past research by U.S. Bureau of Mines (USBM) has developed two methods for mica flotation. One method utilizes acid-cationic flotation for recovery of mica.&apos; This method requires thorough desliming of the ore with consequent fine mica losses. The other utilizes an alkaline-anionic-cationic process for recovering fine-size mica from pegmatite ores after desliming sufficiently to remove clay materials but not so drastically as to remove the fine mica.8-18 The latter process has also been successfully applied to a micaceous schist ore from California.&apos; This report summarizes the results of these research studies. Both of the flotation processes developed by USBM have been adopted by the mica industry and are being commercially utilized separately and in combination for flotation of mica from weathered pegmatite ores. Description of Ores The weathered mica pegmatite ores used in the investigations were obtained from commercial mica operations in Alabama, Georgia, and North Carolina. The

Jan 1, 1971

Jan 1, 1923

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By E. C. Harder

IN view of the gradually decreasing known reserves of high-grade manganese ore and the rapidly increasing consumption of iron-manganese alloys in the steel industry, it is well to turn our attention to the development of low-grade manganiferous ore deposits and to the utilization of these ores in steel manufacture. The dependence of this country on imported manganese ore and ferromanganese has been forcibly brought to the attention of steel makers during the last few years by the cessation of manganese-ore imports from Russia, the restriction of manganese-ore imports from India and of ferromanganese imports from Europe. Should the importation of manganese ore from Brazil cease, the steel industry of this country would face a serious situation. The present practice of steel making requires ferromanganese in large quantities and ferro-manganese of the grade used at present can be produced only from high-grade manganese ores such as the United States appears to possess only in insignificant amounts. There are in the United States, however, large reserves of manganiferous iron ore which could probably be used extensively in the steel industry if certain changes in the practice of steel manufacture were made. Thus high-grade manganese ore could be conserved. Among the most important deposits of manganiferous iron ore in this country are those of the Cuyuna iron-ore district of Minnesota. It is probable that in case of restriction of foreign supplies, the users of manganese in the United States would have to rely to a large extent on the Cuyuna district to make up the shortage.

Jan 9, 1917

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen&apos;s articles and work at the Dutch State Mines exhibited its possibilities in the bene-ficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. l,2,3,4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations.M Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids. While the three applications have been indicated to be feasible, only a meager amount of data is available on capacities and solid elimination eficiency as a function of design variables and cyclone friction loss. This information is essential for the optimum use and construction of the solid-liquid cyclone, and accordingly, work on the problem was initiated at Northwestern University. For the unfamiliar reader, briefly the cyclone consists of a cylindrical section mounted above a truncated cone. The feed nozzle enters the cylindrical ring tangentially with the underflow nozzle permitting discharge of the concentrated solids located at the apex of the cone. The overflow nozzle through which the clarified water exits is centered in the cylindrical section at the top of the cyclone. Half sections of experimental cyclones will be found in Fig la and 6. The feed slurry enters with a tangential velocity, thus creating a spiral pattern of high centrifugal force. The solid particles of sufficient size and gravity are ejected outward to the walls and spirally discharge to the underflow. Most of the water with uneliminated fine solids moves radially inward along the path of the outer

Jan 1, 1950

By S. Epstein

THE new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the con-struction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attrac-tive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately 18,27,28,29,30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved.

Jan 1, 1936

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936