Search Documents

By Robert B. Sosman

The relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. Development OF Method The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreci- ation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. Pyrometry of Coke The coke inside a by-product oven is almost completely inaccessible to pyro-metric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1943

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By John T. Eastlick

The Banner mining district is about 70 miles northeast of Tucson in the southern part of Gila County, Arizona. Production from the district, valued at about $26 million, is chiefly from copper-silver-lead zinc ores. The stratigraphic section consists of Precambrian conglomerates, quartzites, dolomites, and limestones, Cambrian quartzites; Devonian limestones; dolomites, and shales; Mississippian limestones; Pennsylvanian limestones and shales; and Cretaceous volcanic and sedimentary rocks. Deformation of these rocks presumably started near the end of the Cretaceous, and extended into the late Tertiary. The sedimentary rocks were folded, faulted, and intruded by fine grained diorite, quartz mica diorite, and dacite porphyry. At least four distinct stages of mineralization are recognized. In the first stage of contact metamorphism and the second stage of hydrothermal alteration, favorable zones were prepared for ore deposition. Metallization occurred in three of the mineralizing stages. Magnetite, pyrite, and hematite were deposited near the end of the second stage of hydrothermal alteration. The third stage included the main deposition of sphalerite, chalcopyrite, bornite, and galena. In the fourth and final stage, minor amounts of sulfide minerals were deposited with a late anhydrite and quartz gangue. The ore deposits in the form of veins and veinlets, pipes, irregular massive replacements, and bedded replacements are localized by the extent and distribution of metamorphic and hydrothermal alteration, by the proximity to the intrusive contacts, and by the effects of structural development. Oxidized ores of copper, lead, and zinc constituted the principal production of the district prior to 1940, but, for the most part, supergene enrichment was of minor economic importance. The ore bodies of the district are in the mesothermal class of deposits, occurring as normal metasomatic replacement and vein types.

Jan 1, 1968

By AIME AIME

The following report is published for the information of the members Meetings. Two meetings for the reading and discussion of papers, etc., have been held during the year 1906-namely, the Ninetieth meeting, held February 21st to 24th at Bethlehem, Pa., and the Ninety-first meeting, held July 24th to 27th in London, England, in connection with the meeting of the Iron and Steel Institute. The proceedings of these meetings, including descriptions of the entertainments and excursions connected therewith, have already been published and distributed to the members of the Institute; the Bethlehem meeting in Bi-Monthly Bulletin, No. 9, May, 1906, pp. 497 to 508, and the London meeting in Bi-Monthly Bulletin, No. 12, November, 1906, pp. 809 to 908. The proceedings of the London meeting were published separately and distributed among the many individuals and concerns whose cordial friendship and delightful hospitality contributed so largely to the success of the visits in London and environs and the excursions in England, Scotland and Germany. At the Bethlehem meeting, 37 papers and discussions were presented and the names of 198 members and guests were regis¬tered at the Institute headquarters ; this number, however, does not represent all who were present at the sessions and excur¬sions. At the London meeting, 26 papers and discussions were presented, not including 5 of the papers and discussions read before the Iron and Steel Institute at the joint session with the American Institute of Mining Engineers, which, by a mutual agreement between the Councils of the two Institutes, have been selected to be republished in the Bi-Monthly Bulletin and Transactions of the Institute. The number of members and guests of the two Institutes registered at the London headquarters was 908, and of this number 131 were from America. This list does not include the names of all who

Mar 1, 1907

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By John P. Hager, Igor A. Wilkomirsky

The thermodynamic properties of the Pb-Ag system have been determined between 775° and 950°C by the cell: Electrotransport measurements on silica-saturated PbO-SiO2 melts established that the conduction was entirely ionic and that lead is present only in the divalent state. The activities of lead and silver exhibit Positive deviations from ideal behavior. In dilute solutions the activities of lead and silver follow Henry's law. The values obtained for yhb and yig at 1200°K are 1.49 and 1.69, respectively. Determination of a portion of the liquidus curve agrees well with the established phase diagram. provides an accurate means for the thermodynamic study of liquid alloy systems. However, Wagner and wernerl have shown that cells of type I are limited to alloy systems for which the reaction at the alloy-electrolyte interface will be extremely small. The traditional electrolyte for cells of type I has been a low melting point mixture of group IA chlorides, to which a small amount of the compound ACIZa has been added. However, the choice of a chloride electrolyte may not always be practical, in that the Gibbs free energies of formation of the compounds ACIZ, and BCIZb may not be sufficiently different to minimize Reaction [I]. On the other hand, the Gibbs free energies of formation of the oxides of metals A and B may be sufficiently different to minimize Reaction [I]. In this case, the use of molten oxide electrolyte would be clearly advantageous. In the present study, the thermodynamic properties of the Pb-Ag system have been investigated using the cell: Previous galvanic cell studies on the Pb-Ag system2'= are not reliable due to the displacement reaction between the alloys and the chloride electrolyte. Wagner and ~erner,' using Laitinen and Liu's' value at 450°C for the standard electrode potential of Reaction 111, have estimated the percent error in the activity of lead bPb) when using a chloride electrolyte. At 1000°C the error for xpb = 0.10 is 12 pct. Taking the Gibbs free energies of formation for PbClz and Ag cI,' and the equations of Wagner and Werner,' the error in apb at 1000°C and Xpb =0.10 was calculated to be 140 pct. However, using the Gibbs free energies of formation for Pb O' and an estimated value for Ag 20, the error in apb when using a molten oxide electrolyte at 1000°C was estimated to be less than 1 pct for The virtual reaction of cell I1 for the passage of n Faradays of positive electricity from left to right in the cell is: where 5 is the Faraday equivalent (23,063 cal per v equivalent), E is the electromotive force of the cell in volts, and n is the number of Faradays of electricity required for the transfer of 1 g-atom of lead through the cell. The value of n should be equal to 2 since lead is generally divalent in oxide melts. However, the presence of either tetravalent lead ions or electronic conductivity through the molten oxide electrolyte will result in a value of n greater than 2. Bockris, Kitchener, and Davies' have determined the amount of ionic conductance in a liquid PbO-SiO2 mixture (xPbO= 0.50) at 920°C by measurement of the volumes of CO and C& evolved at a carbon anode during electrolysis. From their data a value of 2.13 * 0.16 was calculated for n. Although their measurements indicate the possible presence of multivalent lead ions and/or electronic conductivity, their measurements were not at silica saturation and no definite conclusions can be drawn. However, as a result of the electrotransport measurements described in the next section the ;due of n can be taken as equal to 2.

Jan 1, 1969

"With a total value to date of well over $200,000,000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $ 100,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper.Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade.In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1 924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.The known mineralized area of the district is found in a broad syncline striking north and south. The west limb plunges sharply and extends for a distance on its dip of approximately one and a half miles to the trough. The east limb raises gently through a distance of about two miles to the east limit of known mineralization. This general structure is broken by local faulting throughout the district, the local structural conditions playing an important part in the ore deposition. The north end of the fold is obscured by a rhyolite flow and the south end stops against a monzonite stock."

Jan 1, 1925

By F. E. Lathe, L. Hodnett

This paper summarizes extensive data supplied by 40 copper converter plants in 18 countries, and includes a partial analysis and comments on the effect of converter slag composition and temperature on the fomzation and elimination of magnetite and the life of basic and neutral refractories. APRELIMINARY draft of this paper, including data from 26 companies which had submitted replies to a questionnaire, was presented at the Annual Meeting of the AIME held in New York in February, 1956. Publication was delayed in the expectation that additional replies would be received, and justification for the subsequent delay may be found in the fact that the present revised paper contains data from 40 converter plants situated in 18 different countries. The suggestion that a questionnaire be sent to the major copper and copper-nickel plants outside the U.S.S.R. and associated countries arose at the Los Angeles Annual Meeting in February, 1953, where several papers dealing with converter construction and operation were presented. In private discussions which followed, a group of metallurgists and refractories engineers raised the question why practices varied so much at different plants. Why did magnesite brick give superior service to chrome-magnesite in some plants but chrome-magnesite prove superior in others? Would metallurgical studies point the way to the development of still better refractories? Could magnetite formation be prevented in converter slags and reverber-atory furnace mattes? If this was feasible, why was a heavy circulating load of magnetite tolerated, when, in all probability, it increased copper losses in the reverberatory slags and, in some cases, made it necessary to shut down the furnaces periodically to clean out the accumulated magnetite? Was the sole purpose of coating brick with magnetite that of

Jan 1, 1959

By Richard E. Chism

Some years ago, when I was seeking an illusive fortune and gaining a precarious existence in the primeval forests of Brazil, there penetrated, even to my headquarters in that far-off land, the story of a new-found mining district, where mountain peaks were ribbed with silver, and valleys teemed with virgin gold. Such were the stories that caused hundreds of men to seek their fortune in Sierra Mojada, and to return heaping curses, loud and deep, upon the vivid imaginations that had evolved the glittering fiction. Nevertheless, the rumors had some foundation of truth. The ribs of silver exist, if not the placers of gold; and a flourishing town, of some three thousand people, with two leading mining companies and several smaller ones, in operation, represents what was permanent in the excitement of 1879. Geographical Situation. The town of Sierra Mojada is situated in the State of Coahuila, Republic of Mexico, in latitude 27' 24' N., and longitude 26' 40' W. of Washington, 4' 36' W. of the City of Mexico, and 103' 43' TV. of Greenwich. It lies about 70 miles, in an air-line, N. E. of Escalon station, on the Mexican Central Railroad; but by the present wagon-road, which makes a long detour to turn the mountain range, the distance to the station is about 105 miles. The nearest towns are Huajuquilla, in the State of Chihuahua, about 125 miles due west, and Cuatro Cienegas, in the State of Coahuila, 112 miles to the eastward. Between these points and the town of Sierra Mojada, and to the north of this town, the country is an immense desert, entirely uncultivated, almost uninhabited, and very little known. This

Jan 1, 1887

By R. H. Harrington

The definition of precipitation-hardening1 is well understood and its principles have been subjected to study for some time. However, the variation of properties with double aging, combined with strain-hardening, gives promise of new and useful phenomena. Properly to understand these distinctions, definitions of these terms are necessary. Precipitation-hardening1.—This reaction usually depends upon an alloy having such a composition that it consists only, or in major part, of but one phase, a solid solution, at a high temperature, so that, upon slow cooling, this solution breaks down into two phases, the solid solution and a compound. By heating the alloy to the temperature for maximum solution of the compound, quenching, and reheating to a suitable lower temperature for critical dispersion precipitation of the compound, useful properties of the alloy may be developed to a maximum. Double Aging.—Dougle aging in part is similar to the process for precipitation-hardening, consisting of heating a precipitation-hardening alloy to the solution temperature, quenching, reheating to the suitable dispersion precipitation temperature, strain-hardening, and again reheating to a suitable temperature to develop certain useful properties to a maximum. The strain-hardening may be induced by two methods: (I) a rate of cooling from the first reheat may suffice to strain the solid solution lattice of the alloy; or (2) the alloy may be cold-worked to a suitable degree between the two reheats. Pkecipitation-hardening of Copper-cobalt-beryllium Alloys1.2 The composition of principal interest is that of 2.6 per cent Co, 0.4 per cent Be, 97 per cent Cu. The alloy has been developed commercially and, with certain reasonable precautions, ordinary brass-foundry practice suffices to produce an alloy of high quality. Preliminary Precipitation-hardening Study.—Samples were cut from a I-in. round rod cast in a graphite mold. These samples were then

Jan 1, 1937

By Wheeler North

THE United Eastern Mining Co.'s property is located in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are some 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. TONNAGE MILLED PER DAY 1917 average 234 Maximum month 272 Minimum month 146 1918 average 253 Maximum month 276 Minimum month 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published:

Jan 8, 1919

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935