Search Documents

By Oscar A. Glaeser

The purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings. Need for Ventilation The range between the maximum oxygen content of normal air and the minimum safe content is extremely narrow, approximately 5 per cent. Furthermore, normal air must not be contaminated with irrespirable gases beyond definite limits, and mineral dusts are equally dangerous, although health impairment is slower. Tables 1 and 2 present the more common respiratory hazards encountered in mines. Adequate ventilation is the most effective means available to reduce or eliminate these hazards. Mechanical ventilation has reached varying stages of perfection in coal mines and in many large metal mines. The small mines and prospects rarely have a definite plan of ventilation. As a consequence underground workers are frequently exposed to health and accident hazards. The annual reports of fatalities in mines in the Western States record yearly many deaths due to asphyxiation and deaths caused by men falling down shafts and raises after being overcome by gas. At times mining operations are slowed up because there is no means of driving out the gas after blasting. For that reason only one shift is worked, or men wait from one to several hours for the "smoke" to clear out. Methane gas in varying quantities is widely distributed throughout California. It has been encountered in explosive concentrations in the coast range. It has been found on the Mother Lode and in quicksilver mines near the coast. Methane explosions have not been uncommon in underground operations and in tunneling jobs. These conditions and records indicate that there is room for improvement in mine-air conditions.

Jan 1, 1937

Jan 1, 1918

By Charles M. Rolker

It is not my purpose to present a complete description, still less a thorough discussion from a theoretical stand-point, of the Leadville ore-deposits. Hence I have given to this paper the more modest name of " Notes;" since it is little more than a record of observations made three or four years ago, and now published from my original memoranda, with the view of preserving the facts rather than of

Jan 1, 1886

By Roberts H. Richards

It is nearly twenty years since Dr. Raymond, then U. S. Commissioner of Mining Statistics, wrote the first paper (so far as I have been informed) upon the education of tile mining engineer, as a distinct profession for American youth. At that time nearly all the prominent mining engineers in the country had studied in one or more of the foreign schools, or had reached their high standing through years of experience in the school of life. The paper mentioned five schools in the United States in which some attention was paid to the teaching of mining engineering, but as four of them had barely graduated their first classes, their influence had not begun to make itself widely felt. Two years later the American Institute of Mining Engineers was formed, and it has been a most potent factor in the problem of "disseminating information on mining and metallurgical subjects," so potent that the need of a national school of mines as headquarters for information as well as for instruction is no longer urged. The number of schools also increased, and in 1876 Abram S. Hewitt, in his Presidential address on "A Century of Mining and Metallurgy in the United States,'' gave a list of fourteen. In 1876 the series of discussions, led by Holley's admirable paper, brought the whole subject of technical education before the country. These discussions, while mostly devoted to the engineering professions in general, touched upon the question of mining and metallurgicel training to some extent. Since that time several papers, inspired by the publication of that series of discussions, have appeared in our Transactions, and several notable addresses have been delivered at the opening or at the commencement exercises of various schools. But nothing directly bearing upon the curriculum of the mining and metallurgical schools has ever appeared in our annual volumes. As education is one of the many-sided subjects which cannot be discussed too often, I have ventured to bring it up again. There have been so many good things said upon the subject that one would only need to use the scissors and paste-brush judici

Jan 1, 1887

By Cadwallader Evans

THE American Institute of Mining Engineers was organized in the anthracite region of Pennsylvania by men who were primarily interested in anthracite. Its first meeting, at Wilkes-Barre, Pa., in the Northern Anthracite field, on May 16, 1871, resulted from a call sent out by three outstanding men of the anthracite .industry: Eckley B. Coxe, R. P. Rothwell, and Martin Coryell. The best known of these was Eckley B. Coxe, who was the manager of large hold¬ings operated by him and his family,. and who is remembered as the inventor of a special grate for burning very fine anthracite, known as the Coxe traveling grate, which is still very widely used. R. P. Rothwell was a well-known consulting engineer of the region, as was Martin Coryell, who was associated with another well-known anthracite family, the Pardees. There is no record of the discussions that resulted in this initial meeting, but it is safe to assume that the formation of the Institute was largely influenced, through appreciation by the founders, of the necessity for a free exchange of information covering the whole of the mining industry. One of the rules adopted at the first meeting was:

Jan 1, 1947

By O. M. Schaus

GRATIFYING progress continues towards the elimination of the hazards confronting health and safety in and about mines. Employers and employees are diligently co-operating. One of the outstanding movements towards this end is the National Safety Competition conducted by the U. S. Bureau of Mines. William W. Adams, of the Bureau, has stated that "Through 1936 there has passed by a dozen years of this National Safety Competition, as it started in 1925 with an enrollment of 210 mines and quarries in 28 states and 68 million man-hours of employment. For 1936 it covered 328 mines and quar-

Jan 1, 1938

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By L. D. Ricketts

' In recent years the metallurgical field of the copper industry has expanded greatly, the copper ores have become lean add diverse in charactcr, and we are obliged to treat such ores on a very large scale. On the commercial side, the operating and consulting staffs of the great mining companies have been enlarged and organized, and no great capital expenditure is decided upon until it has been investigated and recommended by a highly organized force of specialists as a committee. I believe that in the scientific field and in the most valuable proceedings of our -various societies the old idea of one-man point of view and one-man treatment of principle and detail together has been splendidly developed and should continue, but for the advancement of our art we should deliberately discuss subjects among ourselves in order to do away with the idiosyncrasies of the individual and to gain a composite view reprcscnting the best thoughts of many men. In the development of new ideas leading to the introduction of new methods, the societies could enlarge their present great field of usefulness if such discussion be had, and in my opinion further great good could be done if a number of men of different qualifications and experience would join in preparing a joint book, each dealing with his particular problem, but consulting the other men. In this way individualism would be preserved and various processes would be described, and if properly reviewed the paper would be palpably capable of analysis, and the student would have at his command the associated efforts of a group of qualified engineers. I have neither the time nor the qualifications to make an investigation and study in detail of hydro-metallurgical processes, but for some years I have foreseen the development of such processes, and I have a deep interest in the subject and have given some of its phases careful consideration from a long-distance viewpoint. I have assisted in directing many experiments and in reviewing the merits of many processes, and am glad to make some introductory remarks with the understanding that other gentlemen present will freely and candidly enter into the discussion and help to fill out the few bare bones that I can uncover.

Jan 1, 1916

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By N. K. Chen, R. Maddin

THE textures of straight-rolled and of cross-rolled molybdenum were first determined with the aid of pole figures by Custers and Riemersma.' These authors have shown that for straight-rolling, the main texture was (100) [0111 with a considerable spread about the rolling direction. After cross-rolling a second texture was obtained in which there was a [111] axis perpendicular to the rolling plane, possessing a rotary symmetry. Recently Semchy-shen and Timmons2 in their study of preferred orientation of arc-cast molybdenum sheet obtained similar pole figures. In these two investigations, polycrystalline materials were used. In the main, the textures of molybdenum in these cases are qualitatively consistent with rolling textures of other body-centered cubic metals, such as iron and Fe-Si alloys." In the present investigation, single crystals of molybdenum were deformed by rolling with respect to specific crystallographic planes and directions. Since the deformation textures of polycrystalline aggregates have been related intimately to the behavior of individual grains,4 a study of possible correlations of final textures with respect to the initial orientations of the single crystals might conceivably lead to a better understanding of the textures. Annealing treatments were carried out after deformation in order to study the recrystallization characteristics as well as the recrystallization texture. Rolling of Single Crystals Single crystals of molybdenum (about 1/8 in. in diarn x 1-in. long), grown by the method previously described,5 were cold-rolled without intermediate anneals. Except for specimens MR-1 and MR-2, which were rolled at random in the preliminary test in order to find a proper rate of reduction, all other specimens were carefully documented as to their respective orientation before deformation by means of X-ray Laue back-reflection methods. A stereo-graphic projection was constructed from which it was possible to determine a particular plane and direction to be considered for rolling. Parallel flat surfaces were then polished metallographically with respect to a reference scratch on the specimen which was mounted in sealing wax. These flat surfaces contained the plane chosen for rolling. After etching, a Laue back-reflection photogram was again made of one of the flat surfaces to determine the exact plane of rolling. The initial orientations of all the specimens (specified by two elements for each crystal, direction of rolling and the pole of the rolling plane) are summarized in Fig. 1. The specimens were mounted in plasticene between two hardened Si-Fe plates. The sandwich was then rolled down, keeping the direction constant in the case of straight-rolling. In cross-rolling (MR-10, MR-11, and MR-12) the sandwich was rotated 90" after each pass so that every first and third pass contained the same rolling direction. Specimens MR-14, MR-15, and MR-16 were compression-rolled following the manner of Barrett." In these cases the direction of the sandwich through the rolls was changed by 3" to 5" for each pass until the specimens were rolled to the desired reduction in thickness. It was found that if extreme care was exercised in rolling, i. e., the amount of deformation per pass was extremely small, the specimens could be rolled to a large reduction in thickness. The rate of reduction used, with a single exception of MR-1. was generally 0.001 in. per 10 passes. Thus, it took about 800 passes to reduce a specimen to a final reduction in thickness of 87 to 98 pct. The results of rolling are shown in Table I. Cold-Rolling Textures The final orientations were determined by the conventional Laue transmission method," using molybdenum radiation, with or without a zirconium filter. Pole figures were plotted from (1101 and (200) reflections in which three degrees of intensity— heavy, medium, and light—were determined visually. Three main types of textures have been observed from the deformed single crystals. These are: 1—a

Jan 1, 1954

By R. A. Burton, J. T. Hansford, D. A. T. Donohue

Substantial evidence indicates that many petroleum producing horizons contain naturally occurring, ordered fracture systems and that within a particular geologic zone, vertical fractures induced in wellbores often will be directed along a particular compass direction. Both conditions will seriously alter the fluid displacement behavior within reservoirs. In this study the effect of induced fracture orientation and length on sweep efficiency is determined for a five-spot pattern. In general, it is assumed that all wells are fractured and directed along the same compass direction. Using the electrical analog to steady state, two-dimensional fluid flow in porous media, boundary conditions are obtained from which flood fronts are tracked numerically. The numerical computations require a particle tracking routine for approximating flood front histories. It is shown that recovery is sensitive to the length and orientation of fractures for the pattern studied. with the proper design of fracture-pattern systems, recovery can be enhanced considerably. INTRODUCTION Hydraulic fracturing introduced in 1949l gave the industry a rather inexpensive means of increasing the fluid injection or production capacity of wells. It has been used with particular success to increase the production rate of wells completed in tight formations, such as in western pennsylvania2 where producers have fractured in depleted or near-depleted fields and observed economic responses. Once the natural energy declines in such a reservoir where all wells have been fractured, waterflooding is generally suggested as means of further increasing recovery. Of the dual objective sought in waterflooding — high injectivity and high breakthrough sweep efficiency — the former condition can be obtained if all wells in the flood pattern are fractured; the latter condition should depend on the nature of the fracture system. Considerable theoretical work has been published on the nature of fractures induced in boreholes.3-5 Although discussion persists concerning the possibility of forming a horizontal fracture at a given point within the wellbore, it is generally conceded that only vertical fractures will develop below a given depth, i.e., where the fracturing Pressure is less than the overburden load. Given the fact that fractures will be vertical in most cases of interest, it is also important to know whether there is order to fracture orientations within a given geological region. Kehle has suggested that in tectonically relaxed areas of uncomplicated geology, the stresses are fairly uniform and all fractures in the region should be parallel.5 Dunlap arrived at a similar conclusion in a theoretical investigation of localized stress conditions surrounding the borehole.6 He concluded that most vertical fractures are propagated in a preferred azimuthal direction. Fraser and Pettitt, in extending these theoretical suggestions to a specific field case, used an impression packer to record both a vertical fracture and the orientation of this fracture in the wellbore of a well in the Howard Glasscock field, Tex.7 Use of this information enhanced the waterflood recovery of the field. Anderson and Stahl also used impression packers on three fractured wells in the Allegheny field. N. Y.. and found that the fractures were oriented more or less along the same compass direction.8 Orientation of the fractures in this manner depends on the stress condition within the formation during fracturing. Elkins and Skov have demonstrated that a natural, oriented, vertical fracture system exists within the Spraberry field? Heck suggests

Jan 1, 1969

Jan 1, 1917

By Robert T. Howard, Morris Cohen

IT has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkin1 has shown that the compositions of two coexisting phases in a a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanalysis.3 Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantitative way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of, this research could not be treated satisfactorily by other quantitative tools, such as specific volume,4 magnetic,5 dilatometric,6 electrical resistance7 or x-ray measurements.8 It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. LITERATURE SURVEY Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1947

By B. F. Oliver

A levitation zone melter is described which has the necessary characteristics for processing metals of controlled purity. No crucible is required; control of the solidification variables is stable; the environment of the charge is chenzically controlled. Rotation of the solidifying interface and mixing in the liquid by the magnetohydrodynamic stirring produce an eight-fold increase in freezing velocity over former melting units with better resulting solute redistributions. The smooth appearance of processed specimens, resistivity ratios as a hnction of position, as well as a segregation curve, are presented as evidence of smooth continuous solute fransport over distances in excess of ten zone lengths. THE difficulties of the floating zone-purification of higher density metals in large quantities under conditions of lowered surface tension are well known and have hindered fundamental research programs for some time. The inordinate amount of time required to obtain a small reproducible yield of high-quality metal has excluded the use of such material for many important material research programs. However, with the use of controllable induction levitation forces' to accomplish stable liquid zones with nearly flat solidifying interfaces, and with good physical and chemical control of the processes involved, these difficulties can be overcome. A zone melter that is to be used for both high-purity and controlled composition work in metal systems must have the following three characteristics: 1) The process must avoid the use of containers. 2) Physical control of the solid-liquid interface and of the mixing within the liquid phase must be stable. 3) The chemical environment of the melt chamber must be controllable. A description of an apparatus that accomplishes these objectives follows.* APPARATUS One of the basic features that is necessary for good process control of large sections is that the charge, the coil, and the motion mechanisms be within the same chamber. This arrangement permits a close coupling between the work coil and the load, which then provides a good flexibility for adjustments of coil dimensions, for controlling the amount of levitation needed for stable operation at a given power level. An overall view of the melter is shown, with the melt-chamber door open, in Fig. 1. The radiation shields surrounding the single-turn induction coil are of water-cooled copper. The chamber is stainless steel, as are most of the components within the chamber. The control panel for the scanner is located at the immediate lower right of the melt chamber. This panel controls the operation of the scanner. The operations controlled are the interface rotation rate, the stretch-squeeze or diameter control, the up and down scanning speeds, and the induction power. All of the drive motors are constant-torque variable-speed motors. The scanning speeds are set with precision helipots and continuously observed with the voltmeter on the control panel and checked with a mechanical indicator within the melt chamber. The rotation rate is also set with a precision helipot. The up-scanning speeds are 2 to 300 in. per hr.

Jan 1, 1963

By John Birkinbine

In the preparation of the paper upon " The Operation of Warwick Furnace, Pennsylvania, from August 27, 1880, to September 1,1885," presented at the Pittsburgh meeting, I purposely refrained from offering theories to explain the peculiarities of furnace operation, on the ground that it was better for those actively engaged in blast-furnace management to present records of operations, than for one more directly interested in blast-furnace engineering and construction to venture upon the sea of speculation as to causes. The manager of an iron-works naturally feels that he knows as much about his particular furnace or furnaces as any one else, and as Mr. Cook, after his close attention to and study of the Warwick furnace, was at that time unwilling to present theories, I felt a disinclination to assume more acumen than the manager.

Jan 1, 1887

By Arcy A., J. G. Davis, D&apos Shock

Results of a pilot operation in the Carlsbad Basin are discussed. After hydrafracing between wells, a block of potash was removed by solution techniques. The distance between frac wells was about 200 ft, the thickness of potash mineralization, 5 ft. By proper manipulation, a feed of concentrate brine was obtained. The ex-periment showed that the thin-bedded potash could be removed by the solution techniques. The details of well construction, method of operation, and removal rates are discussed. Continental Oil Co.'s laboratory research on the fundamentals of potash solution mining has been expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well systems were studied in the field work. Discussion Background: The current paper discusses one field test in which potash was solution mined by a two-well system from a thin sylvinite zone. The potential economic value of solution mining evolves from (1) the use of drilled holes and solution techniques instead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths. Recent interest has been focused on potash' and other soluble minerals, such as trona. Solution extraction minerals, such as copper and uranium, are also worthy of important consideration. In addition, many of the techniques are directly applicable to the construction of horizontal underground storage carverns in salt. There are two general approaches to potash solution mining. The first is to mine on a single-well basis, in which the same well bore is used for both injection and production. This method is slow, and the areal extent may be quite limited in other than very thick ore zones. The second, and the preferred approach, is to mine on a multi-well basis in which the solvent is circulated between wells. This technique, if applied in a manner which allows the ore zone to be mined from the bottom upward, results in nearly all the solution taking place from the cavern roof. Salt removal rates, therefore, are very much higher than from a single-well system.l Wells can be interconnected into a multi-well pattern by several means. One is to join single-well caverns in the lower part of an ore zone. Another is to use the hydraulic fracturing techniques developed in the oil fields.' We preferred the fracture approach because of its potential for creating the greatest area of salt exposure. Test Site Description: The field tests were conducted in New Mexico's Carlsbad Basin, where the potash deposits are flat and uniform over reasonable distances. Here, 12 potash zones are present in the massive Salado Salt section. The specific target was the Third Ore Zone which is about 4 ft thick at our location and about 1150 ft deep. The test pattern was designed in the shape of an equilateral triangle with a fourth well located in the center, 200 ft from each of the vertex wells. This configuration allowed the ore zone to be hydraulically fractured from the center well with good assurance that the fracture would intersect the bore of at least one outside well. Several multi-well test patterns would be available if the fracture connected all wells. Well Completion: Surface casing was set in the top of the Salado Salt at 600 ft to shut off water flows from the surface sands, and the salt section was drilled and diamond-cored to a point below the Third Ore Zone. A drilling fluid made of diesel oil with a small amount of emulsified water was used to drill and core the salt. This fluid was highly successful in preventing enlargement of the drilled hole and in promoting good core recovery. The three outside wells were completed by setting 51/2-in. casing at the base of a streak of anhydrite about 20 ft above the ore zone. Pipe was set high so that the intersection point of the fracture could be detected even if the fracture migrated above the ore zone as it progressed outward from the center well. The center well itself was completed by cementing 51/2-in. casing through the Third Ore Zone. Cement bond logs run on the center well have shown excellent bonding. Fracturing Practice: A mechanical tool was used to cut a notch through the casing and into the salt at a point about 1 ft below the ore zone in the center well. The purpose of this notch was to fix the point of fracture entry into the salt. The fracturing was done with water at injection rtaes as high as 30 bbl per min. The salt parted at 1450 psi; and it required only 5 min for the fracture to reach the well which was 200 ft to the south. It took about 5 min more to reach the other two wells. Caliper surveys were run to locate the point of fracture entry in the three outside wells. The fracture appears to have drifted downward slightly, entering the outside wells at the top of a streak of carnallite 8 or 9 ft below the ore zone. A cross section of the wells selected for the multi-well test is shown in Fig. 1. The figure includes KC1 values based on core analysis and the trace of the fracture plane between the wells.

Jan 1, 1971

By H. Souder

The object of this paper is to bring to the notice of engineers a safety detonating fuse by the use of which misfires in blasting may be eliminated and safety in blasting operations promoted.

Jan 1, 1915