Search Documents

By H. N. Mead

In a reservoir when gas comes out of solution and rises, additional pressure is created because of the change in position of this gar in the bounded volume. If this pressure effect is not taken into account as a pseudo-influx ill mate rial balance calculations on reservoirs in which there is evolving gas, an error is introduced that is directly proportional to the length of oil column and amount of gas evolved and inversely proportional to the reservoir pressure. In reservoirs with small oil column this pseudo-influx is of little importance. The larger the oil column the more important the effect becomes. The most important application, however, will be for reservoirs with declining pressure in which increasing water entry has been indicated by material balance calculations. It could be that this indication is the result of the cited pseudo-influx and not water entry at all. This paper attempts to explain this phenomenon in relation to material balance calculations and prevents an approximate method of determining tile pseudo-influx. INTRODUCTION Only recently has the pressure-volume relationship of gas rising in a liquid appeared in engineering literature, although its effect has been discussed for several years—especially among engineers engaged in drilling operations. The writer published a paper in 1957 in which this phenomenon was examined in relation to blowouts in drilling wells.' Also, in 1957 Stegemeier and Matthews' authored a paper in which the relationship was presented with respect to pressure build-up tests when shutting in producing wells. In this paper the effect will be called "pressure inversion" which is descriptive of the phenomenon. Fundamentally, the effect just mentioned is the result of changing the position of a quantity of energy contained within the gas itself (as a result of its compression) within the bounded volume in which the gas exists. If the gas were allowed to expand "beyond all bounds" there could be no pressure inversion effect. This is because all of the energy contained within the gas as a result of compression would have been re- PRESSURE INVERSION A phase that has not been discussed in the literature is the effect of pressure inversion upon material balance calculations in reservoirs in which the reservoir pressure drops with reservoir withdrawal and is below the bubble point. This action releases solution gas which, after the critical gas saturation has been reached, will tend to rise and collect at the top of the reservoir. The pseudo-influx caused by this effect could be great enough in reservoirs of large oil column and high permeability to render invalid any analyzer studies made on them — if pressure inversion has not been taken into account. Most suspect would be those reservoirs with large oil column in which increasing water entry has been predicted but the bottom wells have not yet produced water. Example 1 Simply stated, this phenomenon exists in oil reservoirs because of the difference in density and expansibility between gas and oil. For example, if a bubble of gas exists at the bottom of a 1,000-ft column of oil having a gradient of 0.30 psi/ft with the pressure at the top of the column zero, the bubble of gas will be compressed to a pressure of 300 psi. If temperature and the combined volume of the oil column and the gas bubble remain constant, as the gas bubble rises in the oil column it will have the same volume and consequently the same pressure at any point. Under these conditions when thc bubble reaches the top of the oil column, the pressure will be approximately 300 psi at the surface and approximately 600 psi at the bottom of the oil column. If it is assumed that the oil is incompressible the pressures will be exactly 300 and 600 psi, respectively.

By Charles Fulton

The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zinc-furnace work recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,1 "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder."

Jan 8, 1918

By E. P. Barrett, T. L. Joseph

The large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent. by mixing ores of various grades, some assaying 4 per cent, silica and some as high as 18 per cent. silica. For each ton of 4 per cent. silica ore mined, a ton of 14 per cent, silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large quantities of ore too lean to be used alone, and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind. This mixing operation, however, can continue only as long as there is high-grade ore available for mixing with the high-silica ores and, while the tonnage of iron ore in the Mesabi Range is still enormous, the tonnage of high-grade ore suitable for mixing with any quantity of low-grade ore is being rapidly depleted. Obviously, if an 18 per cent. silica ore can be reduced by concentration methods to 12 per cent. silica, considerably more of it can be utilized with a given amount of high-grade ore. The operators on the Mesabi Range recognize this situation and are energeticdly endeavoring to reduce the silica in their concentration plants because every unit of silica that can be removed by concentration is a conservation of their high-grade ores. More Elaborate Processes Will Be Needed At the present time there are thirty-seven concentrating plants on the Mesabi Range, and about one-third of the total ore shipped is beneficiated in these plants. In about one-half of these plants no reduction is made in the silica but the moisture or structure of the ore is improved. The washing process is by far the most important method for the removal of silica, and it is interesting to observe that the tonnage of "wash" ore during the past five years has shown practically no increase although the total tonnage of ore shipped has increased. This is due to the fact that the available tonnage of wash ore is being depleted and the amount

Jan 1, 1930

By W. A. Wood, W. H. Reimann

A study is made of the creep that can be induced in armco iron at room temperature by superposing small amplitudes of alternating torsion on a tensile creep load. It is shown that the creep differs from that in comparable tests on copper in being trmsient only. At the same time, though transient, the creep can produce extensions of some 10 pct under creep loads less than the tensile yield stress of the material. The creep can be largely suppressed b$ applying cyclic strain of suitable amplitude before applying the creep load and the metal thereby stabilized. At room temperature, plastic flow in a metal under steady load is normally limited by strain-hardening processes. However, if a small cyclic stress is superposed on the steady load these processes may be more or less neutralized and, as shown in recent investigations,'-4 plastic flow may continue. In this way annealed copper, for example, can be induced to creep continuously to fracture under loads as small as 1 tsi. Dislocation mechanisms possibly responsible for this room-temperature creep have been usefully reviewed by Feltner.But discussion so far has been based mainly on creep as it is found in close-packed metals initially in the annealed state, and their behavior may not be general. In fact, recent work shows that the form of creep in annealed copper is different from that even in cold-worked copper;7 the creep thus depends on the dislocation pattern already in a metal as well as on the metal itself. This paper describes the creep in annealed armco iron, tested in the same way as the above-mentioned copper. One object was to see how creep in a typical bcc metal compared with that in the annealed close-packed metals. Another object was to utilize the fact that a bcc metal like iron has a more pronounced elastic range than close-packed metals like copper and to find to what extent the creep load or superposed cyclic stress had to exceed their re-

Jan 1, 1964

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

By H. P. Greenwald

Those interested in the early developments and experiments, both in the United States and abroad, that led to modern rock dusting, will find an excellent summary in a paper by George S. Rice,13 published in 1914. The period from 1914 to 1924 was one of intensive experiment on coal-dust explosions in the United States; abroad, war activities and rehabilitation stopped this work over a large part of that decade. American findings were published by the Bureau of Mines, particularly in Bulletins 167 and 268. It is convenient to consider that in the United States rock dusting to prevent coal-dust explosions in mines was initiated in 1924 with the publication of tentative specifications.17 This was followed in 1925 by an investigation of methods and costs12 and approval by the American Engineering Standards Committee of a Recommended American Prac-tice.18 Approximately 13 years have elapsed since this approval, and inasmuch as changes in rock-dusting practice in the United States have been evolutionary, it is necessary to consider this entire period as "recent" in some phases of the work. There have been no official changes in the Recommended American Practice since its approval. This paper reviews as briefly as possible knowledge acquired since the issue of the earlier papers mentioned, through experience in mines and experiments conducted by different organizations engaged in the promotion of mine safety. Size of Rock Dust The Recommended American Practice states that the dust shall be 100 per cent minus 20-mesh and 50 or more per cent minus 200-mesh. Results of large-scale tests on the relative effectiveness of rock dust of different sizes were published by the Bureau of Mines15 in 1933 and are reproduced here as Fig. 1. The limiting curve of this figure shows that

Jan 1, 1940

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By Galen Clevenger

THE losses of gold and silver occurring during the conversion of the precipitate, resulting from the cyanide process, into bullion may occur in two ways: first, there may be mechanical losses during the handling of the precipitate up to the time that it is charged into the melting furnace; and second, there may be losses after the precipitate reaches the melting furnace. Much of the loss during the handling of the pre-cipitate can be eliminated, and in fact, in modern plants this loss is known to be very small; particularly since preliminary acid treatment of the precipitate with the attendant extra operations has been abandoned in all but certain plants where gold predominates and this extra step is still deemed necessary. The losses in the melting furnace are from dusting and volatilization; losses in the furnace bottom and linings; floor sweepings; and slag and matte. The gold and silver in the: products which do not: go out of the flue are readily recoverable by standard methods, and while there may be considerable gold and silver tied up at times, the ultimate loss with careful "work should be small. The losses resulting from volatilization and dusting in connection with the melting of the silver slime from copper refineries have been determined by standard methods, and the possible recovery: definitely estab-lished through the installation and operation of electro-static precipitation units. This subject has not been thoroughly investigated in connection with the melting of`. cyanide precipitate; at least, there are no published accounts of such tests. Experiments have been made in the past to determine melting losses by weighing and assaying the precipitate, but this method gives results which are uncertain on account of the difficulty of accurately sampling and assaying cyanide precipitate. Attempts to ascertain these losses by bubbling a measured sample of the gas through cyanide solution or, other absorbent have likewise failed to give depend-able results.

Jan 1, 1922

By Milo W. Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland d Portland Cement Co.. are located- at Metaline Falls, Wash, about 128 miles north of Spokane, on the Fend Oreille river, and 10 miles, of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in the construction of the power plant, the works were not put into operation until August., 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. 1 is a, view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kanisku Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 f and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by 8 ft. in crosssection, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond was used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural -course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By Cecil H. Desch

The progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, determining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(1)† and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By Ward C. Smith

The industry of producing and processing boron compounds is called the borax industry because the chief product is borax, the decahydrate of disodium tetraborate. For the same reason, it is common to speak of borax mining. Reference to borate mining also is common, and while appropriate where it emphasizes the diversity of borate minerals that are mined in various countries, it is rather unsatisfactory where used in a general sense, because it seems to exclude the important production of borax from brine at Searles Lake, California, and of boric acid from steam vents in Tuscany, Italy. The terms "boron industry" and "boron mining" might seem more comprehensive, but are little used, and this is fortunate because they would be misleading-the element boron is manufactured only in small amounts for special uses, and it is not found free in nature. In most occurrences, boron is combined with oxygen and is in a borate or borosilicate material. The history of the modem borax industry starts with the introduction into Europe of borax from Tibet in the 13th century, about the time of Marco Polo, if not actually by him. The discovery that borax has unique value as a flux in metal soldering and ceramic glazing must have been made at some unknown time much earlier. As a rule, any mineral that has been used so long that its early history is lost must occur in deposits that are easily recognized and worked, and this is undoubtedly true of borax in Tibet. According to meager accounts,9 the borax occurs there in arid mountain basins as surficial crusts that coat the ground about thermal springs and seeps of mineralized water, and as coarser crystals in the bottom muds of shallow pools and lakes. Much the same essential features of surface exposures and minerals easy to recognize and recover characterize most of the deposits later found and worked elsewhere. The borax industry at the present time is faced with rising demands for its products, and consequently is increasing its productive capacity and appraising its borate resources.18 The areas that contain the known borate deposits are most likely to yield additional production, hence their distribution in the world is of interest, and is summarized later in this chapter. Mineralogy The mineral raw materials used by the borax industry include various borates mined in several countries, borax extracted from brines at Searles Lake in California, and boric acid extracted from the steam of vents in Tuscany in Italy. The hydrated borates[$] of chief commercial importance are listed in Table 1, which also shows their chemical composition. The properties of only the four most important borates are summarized here, but detailed descriptions of the borates and the minerals commonly found with them can be found in mineralogy textbooks.41 Ulexite generally forms clusters of silky fibers rather than large individual crystals. A

Jan 1, 1960

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today's trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By R. F. Shurtz

This paper relates geostatistical doctrine to classical statistical and mathematical concepts. It is not a contribution to geostatistics; it is a contribution about geostatistics. It uses descriptive and pictorial arguments to assist interested readers in forming an intuitive grasp of the recondite and difficult mathematical issues involved. The method chosen is to cite authoritative literature references from the two fields and trace connections between them. Four broad conclusions appear: first, geostatistics comprises a relabelled subset of concepts detached from classical statistics and mathematics; second, this relabelling artificially isolates geostatistics from the classical fields and restricts its scope; third, the classical fields still have much to offer to the mining industry but will remain fallow unless artifcial communication barriers are removed; and fourth, the unique advantages asserted for geostatistics are neither unique nor necessarily real. These findings should not be regarded as iconoclastic but rather as Pointing the way to a wider and more productive scope for those who evaluate mineral deposits.

Jan 1, 1983

By W. Henry Weimer

A successful surface coal operation requires the combined efforts of engineering and operating personnel. In the planning for a mine, machines should be selected to do the best work in getting the coal uncovered, loaded, and transported to the preparation plant. The best system and extent of cleaning will be determined by the market. After the fundamentals of operation have been established, the operating personnel should see they are carried out. There is no simple solution to some of the every day problems facing the operating officials. Here the production engineer with the technical approach, time studies, control methods, past experience, and available records can help in detecting causes of inefficient phases of the operations. With these studies, a careful analysis can be made in setting up the expected standards to be followed. Management can then compare the job under study with the standards and make corrections to solve the problems. 5.2-1. Annual or Daily Coal Production. Once the production cycle has been established, it is paramount that coal sales keep the productivity of the mine as high as possible. A successful company does this by what they call "the control approach." The daily tonnage report is one of the things that is a potent control tool in attaining the goals to be achieved. If production is falling short of the goal, the daily tonnage report will reveal what has to be done in the remaining days of the month or year to achieve the expected schedule. When goals are reached or exceeded, then budgeted tonnages and costs will be reached or exceeded and thus assure attainment of a profit. Failing to keep to the scheduled pace shows up quickly and prominently, facilitating any necessary action to get things back to the projected plans. The sales target is usually set a little higher than the operating production. The sales tonnage is scheduled and sales are made accordingly, slightly

Jan 1, 1968

By L. G. Austin

The procedure for scaling breakage parameters determined in a laboratory mill to values for a full-scale mill is briefly presented. A simulation model of a closed circuit mill also requires a model of residence time distribution, a mass transfer law to predict over-filling as a function of flow rate through the mill, and a model to describe classification action. For fine dry grinding, or viscous slurry grinding, it is necessary to allow for slowing-down of breakage rates for a fine mill charge. Four examples of comparing simulation models to actual plant data are presented. The first is wet grinding of copper ore in normal closed circuit at 50 tph (metric) production, under conditions where the mill does not overfill. The second is the wet grinding of copper ore in reversed closed circuit at production of 87, 102 and 108 tph, with flow through the mill of approximately 150, 200 and 300 tph. The third is dry grinding of coal with a hot air sweeping stream to remove all of the coal as air-borne material, in open and normal closed circuit. The fourth is grinding of cement clinker in a two-compartment, air-swept tube mill in normal closed circuit with two different classifiers, producing 120 tph of 3250 Blaine cement. In all cases the simulated capacities and product size distributions were in reasonable agreement with actual plant performance.

Jan 1, 1984

By R. P. Rothwell

Instruction by correspondence is certainly one of the most important and useful of modern educational methods. The paper on the " Scranton International Schools," by Prof. Stoek (Buffalo meeting, October, 1898),* gives an elaborate description of a single private enterprise in this direction, ignoring all others, and cannot be said to present a fair or impartial view of

Jan 1, 1900

By J. W. Gwinn

The underground haulage system in the lead-silver mine of the Bunker Hill & Sullivan Co., situated at Kellogg, Idaho, is the most extensive in the Cæur d'Alene district, comprising about 35,000 ft. of tunnels, drifts, and cross-cuts where locomotive haulage is in use. The main working adit, known as the Kellogg tunnel, or No. 9 level, is approximately 10,000 ft. in length from the portal to the main working shaft and extends beyond that about 4,500 ft. in each of two directions. On this level all the ore from the Bunker Hill & Sullivan, the Sierra Nevada Consolidated, and the Caledonia Mining Co.—an average of 44,600 tons per month—is hauled to the mills, located a short distance from the portal. Electric haulage by the trolley-type locomotive is used on this level throughout. Below this level, at intervals of 200 ft. vertically, are five other working levels (Nos. 10, 11,12,13, and 14); and the total haulage distance on these, where electric locomotives are used, is approximately 16,000 ft. No. 13 level has but recently been opened up and is not working to capacity; while the main cross-cut on No. 14 has just been started, and has no need of power haulage. Of the four levels equipped with electric haulage, Nos. 11, 12, and 13 have storage-battery locomotives, and No. 10 still retains the trolley type by reason of the small and decreasing tonnage produced. Electrification - Electric power is supplied to the mine by two systems. The first, the 500-volt direct-current trolley, was installed in 1897 when the Kellogg tunnel was started, and was extended as the tunnel advanced, being used for the first trainload of ore on Nov. 17, 1902, since which time it has been in continuous service. The current for the line is transmitted on a No. 00 copper wire as far as the shaft, and on No. 0 wire throughout the remaining length of the Kellogg tunnel; and until the installation of the storage-battery locomotives it was used in practically all the cross-cuts and drifts on each level below No. 9.

Jan 1, 1915

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925