Search Documents

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By T. Sterry Hunt

THERE are about sixty bodies which chemists call elements ; the simplest forms of matter which they have been able to extract from the rocky crust of our earth, its waters, and its atmosphere. These substances are distributed in very unequal quantities, and in very different manners. As regards the frequency of these elements in nature, neglecting for the present those which constitute air and water, and confining ourselves to the solid matters of the earth's crust, there are a few which are exceedingly abundant, making up nine-tenths, if not ninety-five hundredths, of the rocks so far as known to us. The elements of which silica, alumina, lime, magnesia, potash, and soda are oxides, are very common, and occur almost everywhere. There are others which are much rarer, being found in comparatively small quantities. Many of these rarer elements are, however, of great importance in the economy of nature. Such are the common metals and other substances used in the arts, which occur in nature in quantities relatively very minute, but which have been collected by various agencies, and thus made available for the wants of man. It is chiefly of the well-known metals, iron, copper, silver, and gold, that I propose to speak to-night; but there are two other elements not classed among the metals, which I shall notice for the reason that their history is extremely important, and will, moreover, enable us to comprehend more clearly some points in that of the metals themselves. I speak of phosphorus and iodine. You all know the essential part which the former of these, com- * An address before the Polytechnic Association of the American Institute, during the meeting of the American Institute of Mining Engineers in New York. Printed in this volume by request of many members.

Jan 1, 1873

By AIME AIME

APROXIMATELY one third of the world's iron ore is mined in the United States; and about 80 per cent of this third is mined in the Lake Superior ore region, and about 60 per cent in Minnesota. The Lake Superior iron ore region covers a vast area in the vicinity of Lake Superior that contained in early geological times large areas of iron-bearing sediments, which today form metamorphosed iron-bearing rocks, such as jasper, chert, taconite, and slates. Concentration of the iron content chiefly through solution and resultant removal of silica produced the ore bodies we find today in rock folds as on the Menominee range, at dike or impervious wall intersections such as on the Gogebic range, and blanket-type enriched ore bodies ly¬ing on or within the ore formation, such as occur on the Mesabi and in steeply pitching ore lenses elsewhere. In many places, folding and subsequent erosion of the tops of the folded areas has resulted in steep dips in the ore formation and contained ore bodies. The upper eroded edges are mostly buried under glacial over-burden. The slightly dipping Mesabi formation is the principal exception as to steeply dipping ore bodies.

Jan 1, 1941

By PHILIP N. MOORE

IT is a pleasure to realize even at that day the dignity of the engineer's calling was upheld. May I also add my firm belief that today there be many engineers who will qualify to the specifications of our interesting author. Since that time, the development of the world has been chiefly due to the engineer, and so far as human brain can foresee, the material tasks of the future will continue to follow the directions of his judgment. Popular opinion says this is the age of the engineer; literature, which in the long run, voices public sentiment, shows it in the number of engineers who figure as characters of fiction. The engineer has been doing the big things necessary to increase the comfort and efficiency of mankind, but while a certain amount of fame and repute falls to him, too often he figures as the hired man of the entrepreneur, using that term not in the offensive sense of a mere promoter, but to mean the great visioned master of enterprise who has seen ahead of other men, recognized the coming needs of the world, and through ability to inspire others and to hire capital for his use has also been able to hire engineers as needed. Justly enough, therefore, to such men comes the fame as well as the prize of the game.

Jan 1, 1926

By Robert T. Ault

The nature of fracture in unnotched tensile and notched tensile sheet and round specimens and V -notched and precracked Charpy-type sheet specimens of both wrought stress -relieved and re-crystallized molybdenum was investigated over the temperature range of -78° to 300°C. The sharp rise in fracture stress, for unnotched tensile samples, as the temperature is increased above the brittleness transition temperature (Tb), is found to be a result of an increase in flow stress due to plastic constraint and an increased strain rate which results from the onset of necking at Tb . Quasi-brittle fracture in notched tensile samples is found to occur when the tensile stress at the elastic-plastic interface, beneath the root of the notch, reaches a maximum critical value, which is independent of test temperature over the range from —78° to 25°C, but dependent on microstructure. In the temperature range between 150° and 300°C, unnotched tensile and notched tensile samples alike are found to fracture by a ductile fibrous tearing process which is discontinuous in nature, as a result of the competition between the processes of tearing, through continued plastic flow, and local work hardening. Results from the V-notched and fatigue-cracked Charpy-type impact tests demonstrate that crack initiation is the governing factor in the low-temperature (-78° to 25°C) fracture process for molybdenum. In recent years, there has been considerable interest, and a commensurate number of investigations, concerning the duc tile-to-brittle transition in refractory metals. There has not developed, however, a satisfactory explanation for the uniaxial tensile fracture-stress transition which accompanies the well-known ductility transition. This matter therefore warranted investigation. In a similar manner, the increased importance of notched tensile strength values in evaluating materials and in design criteria requires a better understanding of the factors which control the fracture behavior of notched tensile samples. In a previous investigation1 of the nature of initial yielding and fracture in notched sheet molybdenum at room temperature, it was suggested that plastic constraint was the controlling factor in governing the fracture behavior of notched samples. The final portion of this investigation was concerned with the fracture toughness of molybdenum. Of particular interest was the comparison of effective surface energies for fracture in V-notched samples with fatigue-cracked, Charpy-type samples in order to ascertain the relative importance of the initiation and propagation phases of the fracture process. MATERIALS AND TEST PROCEDURE Sheet tensile, notched tensile, and V-notched Charpy specimens were prepared from 50-mil, stress-relieved molybdenum sheet.* Half of these specimens were vacuum-annealed for 1 hr at 1200°C and 7.5 x l0-5 Torr and furnace-cooled to produce a relatively uniform grain size of 0.30 mm diameter. Round notched and unnotched tensile specimens were prepared from warm-rolled and swaged 5/8-in.-diam bar.* These specimens were vacuum-annealed for 1 hr at 1350°C and 5 x lom5 Torr and furnace-cooled to produce a grain diameter of 0.11 mm. Material analyses in ppm were: C N O H Sheet 290 10 4 1 Bar 50 30 30 2 The unnotched tensile sheet specimens had a 1/4-in. gage width and a 1-in. gage length. The unnotched tensile round specimens had a 9/32-in. gage diameter and a 1-1/4-in. gage length. The sheet and round notch tensile specimens are shown in Fig. 1. All of the notched tensile specimens tested were tandem-notched in order to study the location and mode of fracture initiation. The tandem-notched specimens were carefully machined so that the largest variation in notch depth on a single specimen was 0.001 in. Thus, when fracture occurs, the extent of plastic deformation that exists in the un-fractured notch section is that which exists just prior to fracture. All of the tandem-notched sheet specimens were electrolytic ally polished and chemically etched prior to testing. The V-notched Charpy-type specimens machined from the 50-mil sheet material had the standard dimensions of 2.125 in. long, 0.394 in. deep, and a 0.010-in. root radius. The unnotched tensile and notched tensile tests were conducted over the temperature range of -78° to 300°C, in a 10,000-lb Instron Universal Testing Machine, at a constant crosshead speed of 0.020 in. per min. The V-notched Charpy-type

Jan 1, 1964

By T. Sterry Hunt

THERE are about sixty bodies which chemists call elements ; the simplest forms of matter which they have been able to extract from the rocky crust of our earth, its waters, and its atmosphere. These substances are distributed in very unequal quantities, and in very different manners. As regards the frequency of these elements in nature, neglecting for the present those which constitute air and water, and confining ourselves to the solid matters of the earth's crust, there are a few which are exceedingly abundant, making up nine-tenths, if not ninety-five hundredths, of the rocks so far as known to us. The elements of which silica, alumina, lime, magnesia, potash, and soda are oxides, are very common, and occur almost everywhere. There are others which are much rarer, being found in comparatively small quantities. Many of these rarer elements are, however, of great importance in the economy of nature. Such are the common metals and other substances used in the arts, which occur in nature in quantities relatively very minute, but which have been collected by various agencies, and thus made available for the wants of man. It is chiefly of the well-known metals, iron, copper, silver, and gold, that I propose to speak to-night ; but there are two other elements not classed among the metals, which I shall notice for the reason that their history is extremely important, and will, moreover, enable , us to comprehend more clearly some points in that of the metals themselves. I speak of phosphorus and iodine. You all know the essential part which the former of these, com-

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971

ALABAMA Altoona -Cain, J Anniston-Cowie, L K Hermrod, A A White, H E Bessemer -Abbott, C E Ball, E M Mitchell, F R Thompson, N E Birmingham -Adler, J E Aldrich, T H Aldrich, T H, Jr Blackburn, A R Bush, M W Clark, G H Cowrn, P G Crane, W R Crawford, G G Crockard. F H

Jan 1, 1923

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"' who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1'2 Holtzman,3 Klein; Bahrani and crossland,' and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman's eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By Robert Glass Cleland

DURING the closing month of 1929, Walter Douglas found his health impaired by the strain of many difficult years of alternating prosperity and depression, and in April 1930 resigned the presidency of Phelps Dodge. Douglas was succeeded by Louis S. Cates. The choice broke a tradition that had been held inviolate for almost a hundred years. For the first time in its long history, the direction of the company's policies and operations was entrusted to a stranger without previous Phelps Dodge background, training, experience, or tradition. But the choice was wisely made. For a time at least, the path of Phelps Dodge was to run through rough and dubious ground, and no man in the United States was better qualified to blaze that trail than Louis Cates. After graduating from the Massachusetts Institute of Technology, Cates had served a rough and financially un- profitable apprenticeship at one of the century-old mining camps of Chihuahua, Mexico. Following his return to the United States and a brief interlude as assistant to the president of the National Steel and Wire Company, he had resumed his mining career, first as timekeeper, then as

Jan 1, 1952

By A. J. Weinig

NEED for some simple method of determining tonnages in mill circuits has always been felt by operators and consultants alike. To meet this demand the following method was evolved and has been found accurate and practical after considerable testing on various mill flows. The essence of the method is to add a chemical at a uniform rate to a mill flow, such as a launder conveying pulp, and then determine the concentration of the added chemical in a sample of the pulp. From this procedure the tonnage can be calculated. Common table salt has proved the most satisfactory chemical for ordinary conditions. It has many decided advantages for use in tonnage determinations, among them being the following:

Jan 1, 1933

By Nicholas J. Grant, Robert H. Kane, Bill C. Geissen

The platinum-rich section of the Ta-Pt Phase diagram was worked out by metallographic and X-ray techniques, using twenty alloys; solidus temperatures and solid solubilities were determined. Besides s phase, four intermediate stoi-chiometric phases were found: TaPt (high-temperatzrre phase, structure unknown); TaPt2 (ortho-rhomhic, new type); a TaPt3 (orthorhombic, TiCu3 type); ß TaPf3 (monoclinic, new type). TaPt2 and TaPt3 melt congmentlv; two eutectic, two beritec-tic, and one eutectoid reactions occur in the inuestigated range. THE Ta-Pt system was examined as part of a study of the phase diagrams and the intermediate phases of niobium and tantalum with Group VIII transition metals. Since the main scope of this work was the relation among the ordered close-packed phases occurring in the concentration range from AB to AB3 (A = Nb, Ta; B = Pd, Pt, and so forth), only the platinum-rich side of the diagram was worked out thoroughly, while spot checks were made to determine the approximate outline of the tantalum-rich portion. The system has not been thoroughly treated in the literature; Greenfield and Beck1 in their survey of refractory metal intermediate phases found a o phase between -18 and 37 at. pct Pt which coexists at higher platinum concentrations with an unidentified intermediate phase. Browning2 worked on the range between 55 and 100 at. pct Pt; however, this preliminary study did not cover temperatures >1500°C, and included no conclusive crystallo-graphic data. More recently, a study of the platinum-rich section of the Ta-Pt system has been carried out by Ray,3 while Hartley, Parsons, and steedly4 have studied the tantalum-rich section. The crystal structures of TaPt2, a TaPt3, ß TaPt3, and others have been reported in abstracted form by Giessen and Grant.5 EXPERIMENTAL METHODS The methods of alloy preparation and processing and of the metallographic and X-ray procedures follow very closely those described by Ritter, Giessen, and rant' for other refractory metal-noble metal systems, and will not be repeated except where significant differences exist. Starting materials were: tantalum rod of 99.95 pct purity, supplied by National Research Corp., and platinum sponge 99.9 pct, supplied by The International Nickel Co. An oxygen analysis of the tantalum rod showed 30 ppm O; other impurities were C, N, Si, Nb, Mo, none of these exceeding 50 ppm, and 100 ppm W. Homogeneous buttons were readily prepared as follows: ingots of 5 g were weighed and arc-melted under welding grade argon, followed by two remelts after inverting the button. Between 40 and 100 at. pct Pt, weight losses during the first melt rarely exceeded 0.1 pct, in which case the alloy was rejected, and were nil on subsequent remelts. Since the vapor pressure of platinum far exceeds that of tantalum, the small evaporation loss could be assumed to consist of platinum; therefore, a corresponding amount of platinum was added on the second melt. Since it was confirmed on pure tantalum samples that no weight gain through oxygen or impurity pickup occurs (see Ref. 71, it could be assumed that the uncertainty in the composition did not exceed ±0.1 at. pct for the range 40 to 100 at. pct Pt. For the four control melts from 0 to 40 at. pct Pt, an error of ±0.5 at. pct was calculated. Microscopic examination of the whole buttons after melting showed no inhomogeneity other than local coring. This was eliminated by a homogenization heat treatment. A total of twenty-three alloys were prepared. Heat treatments were carried out in a tantalum

Jan 1, 1965

By John K. Gustafson

The title of my talk is "The Gold Miner and the Future of Gold." This title might just as accurately have been stated as "Gold and the Future of the Gold Miner." Since prehistoric times gold has been sought by mankind for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value and lubricated trade between peoples. For at least 6000 years, gold has been used to barter for other commodities. It has been prospected for, treasured, made into works of art and personal adornment, and from time to time has been the object of conquest. Because of its predominant role in recent centuries as a basis for money, economists began to think of it solely in these terms. Annoyed by the disciplinary pressure of gold on the money manager's desire to manipulate money, the famous economist, John Maynard Keynes, characterized it as a "barbaric relic of the past", a characterization repeated by William McChesney Martin, Jr., when he was head of the Federal Reserve Bank. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world.' It is the most ductile metal known. An ounce of gold, for example, can be drawn into a continuous wire over 35 miles long. It also is so malleable that an ounce of gold can be beaten into films ten one-millionths of an inch thick sufficient to cover 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of gold weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity, only slightly less than silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity both to light and infrared rays. Because of these qualities, in addition to its rare beauty, industrial and artistic uses of gold have been growing rapidly. On a world basis, a recent study estimated that in 1960 about 750 tons of gold were used for fabrication, and that the amount had grown to about 1296 tons in 1968. My objective in this talk is to discuss with you the present and future supply of and demand for gold on a worldwide basis and the effect these forces are likely to have on the price the miner can expect to receive for the gold he produces. This is a highly controversial and risky subject to discuss before any audience. Nevertheless, it is a subject that I live with constantly as Chairman of the

Jan 1, 1972

By J. A. Singmaster

IT will perhaps be wise to define my terms in begin-ning to talk about my subject, especially so where the popular and commercial terminology are as con-fused as they are in the case of zinc. While our French friends know zinc by its true name, and we find Balzac, Daudet, and other literary celebrities using it correctly in their novels, it is quite the contrary in English, particularly here in America. The quotation of a definition for zinc recently appearing in one of our leading technical magazines, "zinc is the place where they wash the dishes," will emphasize the difference. Zinc suffered in the first place by becoming an article of commerce long after its alloys with copper were in common use under the name of brass. Then again, when the art of zinc coating iron and steel objects was commercialized, we called it galvanizing, which is really a meaningless term. The French and Germans use the obvious terms-zinguerie and verzinken-for the opera-tion. Since these two uses of zinc, brass making and galvanizing, have been by far the largest consumers of zinc, is it any wonder that the popular knowledge of zinc is as vague as it is? In fact, since the disappear-ance of the sheet of zinc along with the parlor stove, the zinc-lined bath tub and refrigerator, there has been little popular contact in this country with the undis-guised metal zinc. On the Continent, where zinc has been used for over a hundred years under its real name, particularly for roofing and building purposes, the situ-ation is quite different. It is quite refreshing to turn for a moment to the contrast offered by my friend, Dr. Merica's specialty, nickel. They put 2 or 3 per cent of it into steel, and we have nickel-steel, or a larger amount into an alloy, and we have nickel-silver. To be sure there is no silver there, but what need that matter, nickel is used in the alloy and is first in the name. They plate with nickel and call it nickel-plating, no galvanizing about that. And, finally, they take that noble coin which admits us daily to underground New York, composed of three parts of copper and one part nickel, and get away with nickel as its popular name.

Jan 6, 1927

By L. G. Austin

If S (x) is the specific rate of breakage of size x and B (x, y) (see Table 1 for Nomenclature) is the cumulative breakage distribution function, the Herbst Fuerstenau2 assumption is that Inserting this assumption into first-order grinding equations it has been shown" that there are then simple analytical solutions to the grinding equations, as shown in Table 2. In this context "plug flow" is defined as all material passing through the mill in the same length of time, the residence time t. The term "n fully-mixed" means that the mill has a residence time distribution" which can be treated as if the mill were n equal fully mixed sections in series. In addition it has been shown that the assumption of Eq. 1 also leads to simple analytical solutions for closed-circuit, steady-state grinding with an ideal classifier at the mill exit returning oversize to the mill feed. The solutions are also given in Table 2, with µ as the ideal classifier cut size, C the circulation ratio, and Q (x) the size distribution of the circuit product. The specific surface area of these size distributions is where the density-shape factor k. is assumed to be constant with size. In practice, most methods of size analysis or area [ ] measurement have a finite lower limit, so that the integration is really performed from xm, to xm, For a realistic degree of grinding the value of So is dominated by the fine sizes because of the 1/x factor. Consider batch grinding of a feed of size y to y + dy. The batch grinding solution given in Table 2 is then [ ] The fresh surface area produced is the area of the fines plus the area of the original material remaining minus the area of the original material, [ ] Little error is introduced by neglecting the last term on the right-hand side since at t = 0 it is zero, and when t is significant the first term dominates because of the fine sizes produced. In addition, the form of P (x, t) for [ ] realistic values of S (x) 2t ax° is such that the major fraction of fresh surface produced is contained within the bottom 10% of weight of broken material, that is, for sizes for which P(x, t) < 0.1 (providing y is not near x.,). Thus for surface area purposes Eq. 3 can be approximated by [ ] becomes providing again that the feed sizes are coarse relative to xmi. Then the fresh area production is and W is the mass in the mill. The rate of surface production is WK, and the specific surface is Kt. From Table 2, the specific energy is mt/W so surface production per unit energy is [ ] Surface produced per unit energy input = KW/m (8) where m is the energy input of the mill. Clearly, identical reasoning applies to open-cycle, plug-flow grinding, with t replacing t, and Eq. 8 is obtained again. Considering open-cycle, fully mixed grinding, similar reasoning gives P(x) - t S(x) for surface area purposes, and

Jan 1, 1974

By A. J. Miller, G. R. Brophy

THE Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Grossmann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al .4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be expected that similar results would be obtained. Crafts and Lamont, in their second paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater5 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann&apos;s factors underevaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. [ ] More recently W. Steven6 has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were

Jan 1, 1945

By James E. Little

(Wilkes-Barre Meeting, June, 1911.) OF the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of standard-gauge railroad and two large double-track inclines, the installation of mining-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1909. The ore in its natural state contains a very large percentage of water, which increases to some extent with the depth below the surface. Near the surface it is red in color, with somewhat granular structure. The color gradually changes with depth, finally reaching a bright yellow. The consistency also changes towards, the bottom to a clay-like, sticky mass. The relative proportion of red and yellow ore is quite variable; in some places the yellow reaches close to the surface, while in others the red extends almost to the underlying serpentine. Fig. 1 is a map showing the Mayari division of the Spanish-American Iron Co. The ore lies on an irregular plateau about 15 miles long and 5 miles wide at the widest point, entirely covered with pine trees and brush, which grow directly on the ore. The elevation at the northern extremity, which is approached by the railroad, is about 1,700 ft. above sea-level. At the southern end the general elevation is about 2,000 ft. Ore is removed by means of scraper-bucket excavators and steam-shovels, these machines loading into special standard-guage, side-dump steel cars of 100,000 lb. capacity. A short haul

Aug 1, 1911

By F. B. Plummer

GEOLOGICAL engineering as applied to oil fields, or production geology as some prefer to designate the profession, is designed to fill in the border line between pure geology and pure petroleum engineering. Therefore the production geologist may, and frequently does, reach out to grasp much in both professions. Where once the oil geologist was content to pick samples out of a mud ditch and try to identify oil formations from the color or appearance of flakes of rock bailed out of a well, now he has to deal with graphic electrical logs obtained by intricate and highly technical electrical apparatus and to make exact determinations to the fraction of an inch of the depth and thickness of an oil sand 2 miles below the surface.

Jan 1, 1944

By Roy A. Anderson, Roger H. McConnel

The Metaline district from 1906 through 1965 has produced nearly 16 million tons of ore yielding 400,808 tons of zinc and 178,062 tons of lead. The sediments, ranging from Precambrian into the Devonian, are schist, phyllite, conglomerate, greenstone, quartzite, limestone, dolomite, and carbonaceous slates. Quartz monzonite and granodiorite of the Cretaceous(?) Kaniksu batholith are exposed over a large area beginning a few miles south of the district. There is minor Tertiary conglomerate and basalt. Abundant glacial deposits obscure much of the bedrock. Northeasterly trending folds, having steep to overturned northwesterly limbs, and thrust faults, striking northeasterly and dipping southeasterly, characterize the deformation of the Precambrian and Paleozoic rocks. Recent drilling indicates that the Slate Creek fault, too, is also a southeasterly dipping thrust fault. This new evidence suggests that the Valley Block, like the other major structural blocks, may in part be a thrust plate rather than a graben, and that thus the district may have greater structural unity with the surrounding region than has heretofore been apparent. The Cambrian Metaline Formation of limestone and dolomite contains essentially all the lead-zinc mineralization. Most of the ore mined to date has come from a carbonaceous and irregularly siliceous breccia of sedimentary and diagenetic origin, locally called the "Josephine Horizon," that makes up the top few to 200 feet of the formation. The Josephine Unit is a breccia of gray limestone, coarse light gray dolomite, very thin-bedded, dark gray siliceous dolomite, and "zebra rock" believed to be of algal origin, embedded in a matrix of black dolomite or black jasperoid or some mixture of these two. The jaspcroid fragments and irregular blobs embedded in the black dolomite matrix and the jasperoid laminae in the very thin-bedded dark gray dolomite suggest that jasperoid was formed at the same time as the breccia matrix and as the laminated dolomite. So too, the marked tendency of sphalerite and galena to be disseminated mainly in the dark breccia matrix and their tendency to be most abundant in the jasperoid laminae of the very thin-bedded dark gray dolomite, even where the mineralized and laminated dolomite is fragmented and engulfed in black dolomite breccia matrix, suggests that in these ha bits the sulfides also were deposited contemporaneously with the sediments. Yet very commonly, veins and vague veinlets and patches of white quartz, usually carrying rather coarse sphalerite and sometimes galena crosscut all rock types. These contradictory relationships throughout the Josephine Unit suggest that both the black jasperoid and the sulfides were original constituents of the Josephine Unit but that, locally, they later were remobilized and deposited as white quartz and coarser grained sulfides. Possibly, at least in part, this "metamorphism" is one of the effects produced during or shortly after the intrusion of the Kaniksu batholith.

Jan 1, 1968

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established .R3 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resinsmay serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941