Search Documents

By C. F. Floe, N. J. Grant, A. Joukainen

A CCORDING to Guertler,¹ Smith and Hamilton were the first to study the Cu-Ti alloy system, but because of the presence of large amounts of impurities their data are inconclusive. Hensel and Larsen² in 1930 and Kroll³ in 1931 determined the high copper end of the diagram. In 1939 Laves and Wallbaum,4 in a short summary of compound determinations in titanium binary alloys, mentioned the existence of a face-centered cubic compound, Ti2Cu, with 96 atoms per unit cell, and also a compound, TiCu3, which was said to have a deformed hexagonal close-packed structure in which ordering had been observed. The existence of a compound, TiCu, was also found but the crystal structure was not determined. Craighead, Simmons, and Eastwood determined the effect of copper on the allotropic transformation in titanium. The investigation was limited to alloys containing from 0 to 5 pct Cu, using titanium of fairly high impurity content. Experimental Procedure The methods used for determination of the diagram included metallographic examination and X-ray and thermal analyses. The system was first worked out using the higher purity "Process A" sponge titanium and oxygen-free copper. The high titanium region was next determined more accurately using iodide titanium and vacuum-melted, oxygen-free copper. Preparation of Alloys: The alloys were prepared by arc melting under prepurified helium atmos- pheres in water-cooled copper crucibles. The high purity iodide titanium alloys were prepared by melting three compositions along with a specimen of unalloyed titanium in a single charge. A multiple crucible was used which consisted of a copper plate with four cup-like depressions. The unalloyed titanium was melted first and acted as a getter for any oxygen and nitrogen in the melting chamber. Since these elements harden titanium, the hardness of the standard specimen was an index of the highest probable contamination of the alloy melts. The sponge titanium alloy melts weighed from 100 to 200 g each and the iodide titanium melts from 20 to 25 g. In order to insure greater homogeneity most of the alloys were melted, turned, and remelted twice. The larger buttons made from sponge titanium were sectioned or crushed before remelting. These alloys up to 30 pct Cu were further homogenized by forging at 925°C. They forged readily up to 20 pct Cu but numerous cracks were formed in the alloys containing from 20 to 30 pct. Above 30 pct Cu the sponge titanium alloys were homogenized by heating for 200 hr at 850°C under prepurified helium. Similarly, the iodide-grade titanium alloys containing up to 3 pct Cu were homogenized at 1000°C for 24 hr and all others at 880°C for 200 hr.

Jan 1, 1953

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By M. T. Simnad, C. E. Birchenall, M. H. Davies

THE marker movements observed by Davies, Simnad, and Birchenall during the growth of magnetite on wustite have been misinterpreted. It is the purpose of this note to correct the original interpretation. In that investigation wustite specimens were prepared by oxidizing pure iron disks in water vapor until the iron was consumed. Argon was used as a carrier gas for the water vapor and on the complete conversion of the metal to its oxides ('FeO' plus a small amount (10 pct) of surface Fe3O) the water supply was bypassed and the specimens were annealed in argon alone in order to equilibrate the wustite with the overlying magnetite. After cooling, the magnetite was ground off, a crude magnetic test being employed to determine its complete removal. Radioactive silver streaks were then applied to the surface and the specimen was oxidized completely in water vapor to prevent hematite formation. After complete oxidation the markers were found to enclose about 80 pct of the magnetite with the other 20 pct lying outside the markers. This observation was interpreted to mean that oxygen transport was four times as great as iron transport during the growth of the magnetite. The conclusion would have been correct if, as in the case of wustite growing on iron, all the iron had started from one side of the marker and all the oxygen from the other side initially. Actually a material balance is required. For simplicity, take wustite to be exactly FeO, and magnetite to be Fe3O,. Then at the start of the reaction 3 FeO + O -> Fe,O., All of the iron and three-fourths of the oxygen of the final product will be within the marker inter- faces. The other fourth of the oxygen is in the gas phase outside the marker. From the experimentally determined final position of the markers simple calculation shows that one-fifth of the total iron has crossed the marker interface, while one-twentieth of the total oxygen has crossed in the reverse direction. The simplified result favors iron transport in the ratio four to one. However wiistite is not stoichiometric FeO. At 900°C, the temperature of the measurement, the composition is about FeO When the material balance for the same experimental result is repeated, assuming the product will be 1 mol of Fe3O4, it is found that 0.6 gram atoms of iron and 0.19 gram atoms of oxygen must have passed the marker in the same direction. (This is readily apparent from the reaction to form 1 mol of Fe3O4 SFeO The total oxygen supplied from the atmosphere is 0.61 gram atoms, but the iron which passes the marker interface, i.e., 0.6 gram atoms, requires 0.8 gram atoms of oxygen to convert it to Fe,O,.) If all the transport during magnetite growth is due to iron ion diffusion, then the marker would enclose about 85 pct of the final magnetite and the original measurement is in error by about 5 pct. This error is probably less than the uncertainty in locating the markers by autoradiography. The possibility also exists that the starting wustite was not quite saturated with oxygen and underwent further enrichment with consequent envelopment of the marker before magnetite caught up with the marker interface. In any case it appears that these measurements actually favor iron ion diffusion in magnetite overwhelmingly as the factor controlling its growth, although further experimental measurements are needed to eliminate the error in material balance described. Such studies are planned.

Jan 1, 1954

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.' However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.' Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By Thomas Henderson

Strategically, intermaterials competition is important to companies involved in raw materials extraction, smelting, refining or other processing, semi-finished and finished goods fabrication, and end-use consumers. In other words, just about every company involved in manufacturing. The array of materials covered by other papers in this session is testimony to the subject's breadth. In trying to provide an over- view of such a broad topic, the purpose has been to relate some of the common characteristics of the markets, economics and technology of raw materials, and to describe some of the ways in which Intermaterials competition impacts the markets, economics and technology of raw materials.

Jan 1, 1982

By R. F. Mehl, R. W. Parcel

THE rate of the decomposition of austenite in eutectoid steels, forming only pearlite, may be expressed fundamentally in terms of the rate of nucleation and the rate of growth of pearlite nodules. This matter has received much attention in recent years. (The basic references are listed in ref. 1; references of particular import to the present work will be given separately.) Systematic data have been developed for plain carbon eutectoid steels.:! Although the physical factors affecting the rate of nucleation, N, in case of plain carbon steels have presumably been identified, they cannot as yet be evaluated quantitatively.' Several somewhat successful attempts, however, have been made to calculate the rate of growth, G. In the latter case the important factors determining the edgewise growth of pearlite have been assumed to be: 1—the interlamellar spacing; 2—the concentration extremes and concentration contours of carbon in austenite in front of the growing pearlite interface; and 3—the rate of diffusion of carbon in austenite.* The only systematic data on N and G for pearlite in alloy eutectoid steels are those for Co-steels;6 there are no data on alloy eutectoid steels in which the alloying element is known to decrease the rate of formation of pearlite, apart from a few scattering data reported earlier' for steels containing manganese. This paper reports a systematic study of N and G for eutectoid alloy steels containing molybdenum and nickel, respectively. In order to provide information of help in understanding the results, new data are presented on the effect of molybdenum on the interlamellar spacing of pearlite, So; data on the effect of nickel on So have already been published.' The alloys used were in five groups: 1—Pure Fe-C-Mo alloys (Table I) were supplied by the Climax Molybdenum Company of Michigan, Detroit. They were made from Armco ingot iron of standard analysis, Acheson graphite, and ferro-molybdenum, melted in silica-lined crucibles in a high frequency induction furnace. The ferromolyb-denum was added to the melted steel, followed in 5 min by 0.08 pct Al. The ingot as-cast measured 23/4x 31/4x10 in.; it was hot-forged at 1150°C to a bar 1 in. sq.

Jan 1, 1953

By Sherwin F. Kelly

THE joint meetings of the Mining Geology Committee and the Society of Economic Geologists proved to be deservedly popular, and the interesting papers drew an attendance which strained the capacity of one of the large meeting rooms.. As might be expected these days when even the Supreme Court can't keep away from the subject of gold, the discussions opened on Thursday morning with several papers devoted to questions of structural and mineralogical relationships of the deposits of this metal. The presentation of Ira B. Joralemon's paper, "Veins and Faults in the Bralorne Mine," by Reno Sales, elicited considerable discussion on the relation of mariposite to gold, and the situation of the gold deposits with respect -to the Coast Range batholith. H. V. Warren stated that lie had observed mariposite always to be associated with gold in this region, but that gold was not always associated with mariposite. He pointed out that there is a series of veins on the west side of the batholith with a different mineralogy that, because of their richness but small size could quite easily make good, small mines. John A. Dresser concurred in this, and said lie thought this region was one of great promise for the mining geologist. He also reported having found mariposite associated with gold values below commercial limits, in the Appalachian regions.

Jan 1, 1935

The following is an incomplete list of members and guests who called at Institute headquarters during the period May 10, 1919, to June 10, 1919. Victor C. Alderson, Golden, Colo. E. Fleming L'Engle, Joplin, Mo. H. Foster Bain, Washington, D. C. W. D. Mainwaring, Philadelphia, Pa. J. J. Beeson, Master Engr. Sr. Gr. W. G. Matteson, Fort Worth, Tex. Gunnar Bergstrom, Stockholm, Sweden. C. E. MacDonald, Toronto, Can. Corry T. Brown, Socorro, N. Met. Francis Nicholson, Charlotte, Va. Geo. W. Brymer, Scranton, Pa. Richard A. Parker, Denver, Colo. W. Burns, Santa Fe, N. Mex. S. B. Patteson, Jr., Allentown, Pa. H. C. Carlisle, The Pas, Manitoba, Can. G. W. Ponton, Ottawa, Canada. J. Carson Adkerson, Va. W. H. Reber, Ensign, Dallas, Tex. C. A. Cheney, Madison, Wis. T. C. Roberts, New York City. J. M. Clark, Toronto, Canada W. A. Rukeyser, Ensign, N. F. Corps. John J. Doyle, St. Louis, Mo. W. H. Staver, New York City. H. S. Emlaw, Grand Haven, Mich. D. B. Sterrett, Washington, D. C. E. Francis, Birmingham, Ala. T. V. Smirnoff, Russia. Rudolf Gahl, Denver, Colo. E. C. Templeton, New York City. Emit Gthmann, Baltimore, Md. H. A. Toblemann, Ajo, Ariz. A. B. Hardie, Philadelphia, Pa. Priestley Toulmin, Birmingham, Ala. Clarence M. Haight, Franklin, N. J. M. R. Walker, Baltimore, Md. N. V. Hansell, New York City. H. A. Wheeler, St. Louis, Mo. C. A. Heberlein, Nacosari, Mexico. D. B. Whitaker, Santiago, Cuba. Pierre Hines, Milwaukee, Wis. A. W. G. Wilson, Ottawa, Can. J. S. Hollings, Brymoba, Wales. Oba Wiser, Hanover, N. Mex C. Vey Holman, Maine. Harry J. Wolf, Denver, Colo. H. H. Howry, Denver, Colo. F. H. Wood, Mt. Vernon, N. Y. W. Spencer Hutchinson, Boston, Mass. J. P. Wood, New York, N. Y. W. B. Kunhardt, Reading, Pa. Lawrence Addicks sailed on May 17 for London; lie expects to be absent from this country for several months. Roy H. Allen has accepted a position in the research engineering department of the National Aniline & Chemical Co., Buffalo, N. Y. H. Foster Bain has gone to Shanghai, China, where he expects to remain for some time. Percy J. Bandy has accepted a position with the Cia. Minera del Mirasol S. A., at Cusihuiriachic, Chihuahua, Mexico. J. H. Batcheller is now with the North Midas Copper Co., St. Helena, Alaska.

Jan 7, 1919

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By William T. Folwell

The Lucky Friday mine east of Mullan, Idaho, is an outstanding example of a property in the Coeur dlAlene district where a small and insignificant-appearing silver-lead-zinc vein at the surface has changed at depth into a large vein of great importance. The Lucky Friday vein has little if any surface expression and above the 1200 level the ore shoots are small and discontinuous. Between the 1200 level and 2450 level, the lowest developed level, the main ore shoot has shown remarkable improvement on each succeeding lower level, and today the mine is one of the major lead-silver producers in the Coeur d'Alene district. History: The Lucky Friday property is on the north side of the South Fork of the Coeur d'Alene River in sections 25, 26 and 35, T. 48 N., R. 5 E., Hunter mining district, Shoshone County, Idaho. This is about one mile east of the town of Mullan, which serves the eastern portion of the Coeur d'Alene district. The southern part of the property is crossed by a branch line of the Northern Pacific Ry. and by U. S. Highway 10. This highway is the principal road crossing the panhandle of Idaho and connects the district with Spokane, Wash., on the west and Missoula, Mont., on the east. The main portal and surface plant of the Lucky Friday mine is at an elevation of 3365 ft, only a short distance above the valley floor and a few hundred feet from U. S. Highway 10. so the mine is readily accessible for year-round operation. The property is comprised of six claims, known as the Lucky Friday group, owned outright by the Lucky Friday Silver-Lead Mines Co. There are four patented claims, Good Friday, Lucky Friday, Northern Light, and Lucky Friday Fraction No. 2 (Mineral Survey No. 3028), and two unpatented claims, Hunter and Creek. In addition, Lucky Friday owns an undivided one-half interest in the Hunter Creek property. which adjoins the Lucky Friday group on the north: a 90 pct interest in the mineral rights in the Jutila Ranch (160A), which adjoins the Lucky Friday group on the east; and a 60 pct interest in the Lucky Friday Extension claim group, which adjoins the Lucky Friday group on the west. The company also has a long-term mining lease on the Hunter Ranch, which adjoins the Lucky Friday group on the west. The claims of the Lucky Friday group were located between 1899 and 1906. The Lucky Friday Mines Co. was organized in 1906 and did considerable exploration work by surface trenching and shallow underground workings, only to see the property sold by the Shoshone county sheriff to satisfy labor claims totaling $2000 in 1912. Another firm, Lucky Friday Mining Co., bought the claims in 1914 and spent 12 years driving what is now known as the tunnel level crosscut. This tunnel intersected a vein previously exposed in a higher tunnel, but it was only a few inches wide. The vein was followed a short distance westerly but was so unpromising that the work was discontinued in favor of extending the main crosscut tunnel several hundred feet north. No ore was found and all work was discontinued. The property was held in such low esteem by the firm that it let taxes amounting to less than $15 a year go delinquent for nine years. Then the property lay idle for two more years until in 1938 John Sekulic, a Mullan service station operator, took a lease, with a $15,000 purchase option, on the advice of an old miner who had worked in the mine. Sekulic re-opened the tunnel level crosscut and explored the vein with an easterly drift for about 200 ft. The vein was too narrow to be of commercial value but was believed interesting enough to warrant further exploration at depth. Lacking funds to explore the vein at depth, Sekulic tried to get the district's larger operating companies to take over his lease and option. They were not interested because of the lean tunnel level showing and the fact that the property lay between the White Ledge fault on the north and Osburn fault on the south, an area which geologists always considered unworthy of exploration. Sekulic then organized the present company and assigned his lease and option to it for stock. This was in 1939. Enough stock was sold locally to finance sinking of a shaft 100 ft from the tunnel level east drift. The vein at this additional depth still was not commercial but showed some improvement. Treasury stock was offered at 5 to 10C a share

Jan 1, 1959

By B. R. Hollebone

The chemical action of molten anhydrous pyridinium chloride (pyridine hydrochloride) on oxy salts and ores of some Group IV and V metals are discussed-in particular zirconium, hafnium, niobium (columbium) , and tantalum. Laboratory-scale experiments are described whose results suggest that this reaction might provide a practicable means of converting ores of these metals to the anhydrous metal chlorides. Experimental results are given which provide some insight into the nature of the reactions and some of the compounds which could be present at intermediate stages. The treatment of ores of the more refractory metals is difficult and expensive and often demands the use of gaseous chlorine, hydrogen fluoride, or other reagents which are, if nothing else, expensive and dangerous to use. This situation is, of course, due to the strong metal-oxygen affinity resulting from the high charge and the small size of the metal ion which combine to produce such high lattice energy in the metal oxide as to defeat standard reduction methods. Thus, the characteristic of these metals which leads to one of their most important properties—corrosion resistance—is the main hurdle in obtaining the metal. Many common methods' for treating ores of zirconium and niobium (columbium), for example, proceed as directly as possible to the preparation of anhydrous halides. These halides are purified by now standard processes of solvent extraction, fractional distillation, and so on. This paper reports on preliminary stages in the development of a method of treating these ores—particularly of niobium—so as to prepare the anhydrous, volatile halides by the use of chemical reagents which are much more easily handled than those used at present. CHEMICAL PRINCIPLES The solvent action of aminium halides has been referred to periodically in the literature over several decades. The chemistry of pyridinium chloride has been discussed particularly by Audreith2 and Starke.3 However, since this is not familiar chemistry in its nonaqueous setting, it is perhaps well to point out some general metallurgical principles and applications. One can use, as point of departure, the fact that HC1 dissolved in pyridine is an acid very much the same as aqueous HC1. It thus gives essentially all the reactions of the HC1 with which we are familiar. However, when the ratio of HC1:pyridine reaches 1:l (a ratio far higher than is possible with H2O) the solution becomes solid C5F5NHC1, pyridinium chloride.* Inter- estingly, the acidic properties of HC1 persist in this medium, although they are manifest only in the molten state of the compound. Some typical reactions of divalent metal compounds which we have carried out in our laboratories are the following: 2PyHCl + Zn — (ZnCl2) + H2 + 2Py 2PyHCl + MnO — (MnCl2) + H2O + 2Py 2PyHCl + CuS — (CuCl2) + H2S + 2Py 2PyHCl + CaCO3 — (CaCl2) + H2O + CO2 + 2Py In these equations, the parentheses indicate a solvated compound which in water would be predominantly a hydra ted cation but which in molten PyHCl will more likely be a complex chloro-anion of the type MC14-. Some important physical properties of pyridinium chloride (PyHCl) are given in Table I. One sees from the data in Table I that at the temperature of molten pyridinium chloride both water and pyridine will boil away. Thus the system will be kept anhydrous. For this reason the reaction 2NbCl5 + 5H2O— Nb2O5 + 10HC1 has no counterpart in molten PyHCl. Instead, the chloride is made even more stable by the formation of a hexachloro complex: Nb2O5 + 12PyHC1 — 2PyHNbC16 + 5H2O + 10Py One interesting property of these complexes is their thermal instability which for the case of niobium can be illustrated as PyHNbCl6 — PyHCl + NbCl5 With a view to possible use of this chemistry in ore treatment, we have attempted to dissolve Pyrochlore (essentially FeO - Nb2O5) and recover the NbC15 from it.

Jan 1, 1968

By Cyril Wells, Robert F. Mehl

The purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2o C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made2. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsenl that variations as great as 30' C. exist in the reported data on the A3 temperatures in iron-carbon alloys. Fortunately, the Aa temperature in pure iron is now known to be 910" C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato5 on both hypoeutectoid and hyper-eutectoid steels. Esser made a dilatometric and magnetic study of iron and iron-carbon alloys containing 0.06 to 0.86 per cent C, for which a high purity is claimed. Presumably the electrolytic iron was reasonably pure, but the alloys contained considerable impurities, on the average totaling 0.35 per

Jan 1, 1937

By W. T. Hicks

The oxidation of CbO was studied by a gravimetric technique from 400° to 1200°C in oxygen. In this temperature range the oxidatiotz is characterized by an irlductive period of low oxidation rate, which becomes shorter as the temperature increases, followed by a rapid parabolic oxidation. The oxidation of CbO cannot be rate controlling in the oxidation of Cb metal in the temperature range, 800° to 1200°C. A thin optically inactive layer has been observed between the metal and Cb2O5 layer of Cb oxidized at 700°C or higher temperatures. Figs. 1(a) and 1(b) show the edge of a sample of Cb reacted to 50 pct of complete oxidation at 800°C. Fig. l(a) taken under bright field illumination shows a layer of oxide adhering to the unoxidized metal core. Fig l(b) taken under polarized light shows that this oxide layer is

Jan 1, 1962

By Joseph A. Holmes

(Pittsburg Meeting, March, 1910.) AT the Mining Experiment Station of the U. S. Geological Survey, in Pittsburg, an investigation of the process of combustion is being carried on in a specially-designed furnace having an unusually long combustion-chamber. This work is conducted by a committee consisting of H. Kreisinger, mechanical engineer; Dr. J. C. W. Frazer, chemist; and Dr. J. K. Clement, physicist. The problem, essentially one of physical chemistry, is extremely interesting to all who are concerned in the burning of coal or the construction of furnaces. The main object of these experiments is to ascertain the relation between the amount of the volatile combustible driven from the coal and the combustion-spaces necessary to burn it completely. Our best steam-coals vary from 15 to 45 per cent. of fixed combustible. The greater part of the latter is burned on the grate; but the volatile combustible leaves the freshly-charged coal and must be burned in the combustion-space. If this space is not large enough, the volatile combustible will leave the furnace only partly burned, and the result will be a considerable heat-loss and a smoky stack. Strictly speaking, the factor which determines the completeness of combustion of the volatile matter, after it has been mixed with a certain amount of air, is the length of time the mixture is allowed to remain in the combustion-space; but this length of time depends on the extent of the space itself. Let us suppose, for instance, that, when a given coal is burned at a certain standard rate, the volume of the volatile combustible driven off per second is 10 cu. ft. Adding, say, 10 cu. ft. of air, the volume of the resulting burning mixture is increased to 20 cu. ft. If the combustion-space is 20 cu. ft., the burning mixture will stay in it,

May 1, 1910

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick's second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method' are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5' could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5' or Ag'lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5' and 0.6 N HNO3 solution for the A"'), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5' atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By O. J. Hollister

Jan 1, 1888

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1918 to Nov. 10, 1918. J. Carson Adkerson, Virginia. George H. Parsons, Hayden, Ariz. Andrew B. Armstrong, Connecticut. W. E. Pomeroy, New York. Courtenay DeKalb, San Francisco. Ezra C. Rider, Bisbee, Ariz. Clifford G. Dennis, San Francisco. H. W. Seaman, Chicago, Ill. Rudolph Emmel, Boston, Mass. William Allen Smith, Northampton. Emil Gathmann, Baltimore Md. R. K. Stockwell, Salt Lake City, Utah. Ernest S. Geary, Denver, Colo. W. G. Swart, Duluth, Minn. W. E. Hopper, Washington, D. C. Kirby Thomas, New York. W. Spencer Hutchinson, Boston, Mass. - Warren D. Thompson, Harvard Club. E. W. Kohl, Jr., Philadelphia, Pa. H. Vincent Wallace, Los Angeles, Cal. E. C. Nighman, Butte, Mont. Paul T. Benson, formerly with the Tacoma smelter, has resigned his position there to accept one with the Great Metals Mining and Milling Co. at Nespelem, Wash. Prof. Edward E. Bugbee, of the Mining Department of the Massachusetts Institute of Technology, has been granted a leave of absence to accept the position of Assistant Director of Education for the S.A.T.C. of five southern states with headquarters at Raleigh, N. C.

Jan 12, 1918

By Enid C. Plante

INTRODUCTION To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), marcasite (FeS2), orpiment (As2S3), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also examined to determine if its behavior could be correlated with that of pyrite or marcasite (FeS2). EXPERIMENTAL METHOD Mineral for Flotation and Contact Tests Mineral was prepared in the manner already described' and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and C02 free air bubbled through each suspension at a constant rate (about 1 bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation of oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.1 No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 FLOTATION OF "UNOXIDIZED" MINERALS WITH ETHYL XANTHATE AS COLLECTOR Fig I to 3, 4, 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox3 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C. Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1947