Search Documents

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum deposit, Eureka County, Nevada, occurs In a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusive. For samples from the 25000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8: 1 at 10-mesh, 8: 1 at 70-mesh, 6: 1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp 1s used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of ± 25%. The error distribution is not based. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1984

By Lysle E. Shaffer

INCREASING attention has been given in the last decade to the possibilities of mine leasing in the West. The practice as described in this article does not refer to the leasing of entire properties for corporate operation. It is intended to deal rather with the advantages and problems incident to leasing portions of properties to individuals who themselves, individually or in groups, do the actual mining and transportation of the ore. These individuals are sometimes called "leasers" and sometimes called "tributors." The contracts under which they work set up an independent relationship of lessor and leaser, between themselves and the mineowner or operator. This relationship has many advantages to both sides over those created by the ordinary relationship of employer and employe. From the standpoint of the owners there is no liability on independent contractors for industrial injuries, social security taxes, unemployment taxes, or the manifold restrictions of the Federal Labor Relations and Wage Hour Acts and similar state acts where they exist. As the leaser's income depends on the quantity and quality of ore produced, there is a distinct incentive for maximum production of a good grade of ore. This in turn promotes careful mining of the areas under lease. Ordinarily in mining, labor cost is a high percentage of the total cost of operation. Under a leasing system, even if the leasers be allowed to retain half of the gross values that they produce, and the owner or operator gets half, in the case of marginal ore bodies this is ordinarily more than the lessor would realize if the property were worked by day labor. In some instances mineral deposits under a leasing system may become ore, whereas under a day-labor system they would

Jan 1, 1948

Executive J V W. REYNDERS, Chairman WILLIAM H. BASSETT E DEGOLYER H C BELLINGER RICHARD PETERS. JR. Finance H. A. GUESS GEORGE OTIS SMITH, Chairman F. JULIUS FONS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A MOSMAN El K MASTERS J. A. SINGMASTIIR Alternates F. G. BREYER C W HAMILTON F. E PIERCE

Jan 1, 1923

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By M. Cohen, C. Wagner, J. E. Reynolds

If the total volume of a diffusion couple changes during the diffusion, the measurement of distance becomes ambiguous. Use of distance parameters as suggested by Hartley and Crank is discussed. For small concentration differences, the standard form of Fick's second law is retained with conventional length units and the in- terdiffusion coefficient D. It is shown how D can be calculated from experiments involving large concentration differences and analyzed in terms of distance parameters. 'The merits of incremental diffusion couples involving small concentration differences are emphasized. THE conventional form of Fick's second law for one-dimensional diffusion of component B in a binary solution of A and B is where c, is the concentration of component B; x, the distance; t, the time; and D, the interdiffusion coefficient which may depend on ca. Hartley and Crank' have pointed out that Eq. 1 applies only if the total volume of the diffusion couple does not change during the diffusion process; otherwise, the definition of x becomes ambiguous. No change in total volume takes place if the specific volume of the solution is a linear function of the weight fraction Wb, or if the molar volume is a linear function of the mol fraction N. In some alloys, however, these relationships do not hold, and then it is necessary to introduce a modified measure of distance, 4 in order to retain the general form of Eq. 1. The application of Hartley and Crank's suggestions to diffusion in alloys has been discussed by Wagner.' Relation Between Measure of Distance and Units of Concentration The definition of [ depends on the choice of units for the concentration c,, as follows: 1—If the concentration ca is measured as the weight fraction W, (or weight percent), [ = 5, has to be defined so that equal increments of contain equal increments of mass m of the solution, e.g., dm = pSdx = Sdw [2] where p is the local density of the solution, and S is the cross-sectional area in sq cm which is taken to be constant in this problem of one-dimensional diffusion." * da Silva and Mehla have demonstrated the constancy of the cross-sectional area in the usual type of diffusion couple. However, experiments involving diffusion into thin wires4, 5 may exhibit changes in cross-sectional area, and therefore are excluded from the present treatment. Thus and the unit of is gram per sq cm instead of cm. 2—If the concentration c, is the mol fraction N, must be defined so that equal increments of contain equal numbers of mols of solution, e.g., dn= (S/V)dx= Sd [41 where V is the local molar volume of the solution. Thus dt, = dx/V [51 and the unit of is mols per sq cm. 3—If, as may be advisable in the case of interstitial solutions, the concentration C is measured in terms of the molar ratio of components B and A (c,, = Y, = nH/nA, where n and nl are numbers of mols of B and A), = Y has to be defined so that equal increments of contain equal numbers of mols of A, e.g., dnA= (NAS/V)dx = Sdf [6]

Jan 1, 1954

By J. Gurland

The effects of variations of carbon content on the constitution and properties of sintered WC-Co alloys were studied. The grain growth of tungsten carbide during sintering was measured and it was shown that it takes place mainly by solution and reprecipitation of the carbide in and from the binder at the sintering temperature. It was found that the decomposition of W3C03C by carburization during sintering is responsible for the formation of very large grains. THE properties of sintered WC-Co alloys are critically dependent upon their final composition and structure. Slight changes of cobalt and carbon contents and small variations of grain size result in marked changes of mechanical properties and performance of products. Previous investigators have studied the microstructure as a function of composition' and have dealt with the influence of cobalt upon properties.' The present work is concerned with the effect of carbon content upon constitution, microstructure, and grain growth during sintering, as well as upon the physical properties of sintered compacts. Phase Boundaries at the Sintering Temperature The WC-Co section through the ternary diagram W-Co-C has been studied by Wyman and Kelley,' Takeda,V andford and Trent," and Rautala and Norton." Two phases, namely WC and a cobalt-rich solid solution (P), appear in the sintered structure if the carbon composition corresponds very nearly to the theoretical carbon content of WC (6.12 pct C). But small deviations from the ideal carbon content will bring about the occurrence of either graphite or the double carbide W,Co3C (7) . The 7 phase was long believed to be metastable, this conclusion being based mainly on the work of Takeda. More recent studies have shown that it is a stable phase of the ternary system,"5 but the actual phase boundaries have not been established and there has been some discussion as to whether or not the 7 phase occurs at some stage of sintering in the fully carburized alloys." In view of this uncertainty it was thought advisable to undertake an investigation of the phases present during the sintering of WC-Co alloys. Commercially available tungsten, cobalt, and carbon powders were used in the present study. A typical analysis of impurities in a sintered compact is reported in Table I. The desired carbon compositions were attained by varying the amount of carbon added to the tungsten during carburization and controlling the composition during sintering by packing the compacts into beds of mixed alundum-carbon powders of suitably selected ratios. The alloys were sintered in a hydrogen tube furnace at 1400°C, then brought to equilibrium at the temperature under investigation and quenched in water. The high temperature phases were identified by metallographic and X-ray diffraction techniques. The samples were etched with a 10 pct solution of alkaline potassium ferricyanide. The phase boundaries, established by metallo-graphic examination, are shown in Fig. 1, which is a vertical section through the ternary diagram at 16 pct Co. The temperatures of the invariant planes, at 1298" and 1357°C were established by Rautala and Norton. The vertical section shows that the three-phase field, WC + 7 + L, extends into the two-phase field, WC + L, but does not include the stoichiometric composition of WC. In practice this means that the 7

Jan 1, 1955

By R. G. Hall

WHEN we want to interpret some problem which faces us at the present, if that problem be a social or political movement, we turn to the pages of history for 'information. If the problem be one of science or of industry we turn to the library of the subject and endeavor to translate the present from the experience of the past. I wonder if you would bear with me for a few minutes as I look back to the time when I was going through mining school and looking forward with hope, it is true and with confidence also, but still with some trepidation and an occasional qualm, to the month of June when the class of 1897 would be hunting jobs. Those were the years 1893 to 1897. Those years saw the Treasury of the United States so empty of gold that the President had to appeal to financiers to accept the country's promises to pay in return for $100,000,000 in gold. And the invectives that were hurled at both their heads for such a betrayal of the people sound strangely similar to those you read today being daily written and screamed at another President for taking us into the League of Nations or for not issuing bonds in huge amounts for unemployment relief, or for not adopting somebody else's particular specific for the relief of hard times.

Jan 1, 1931

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By M. G. Magnuson, H. O. Hofman

When dry chlorine gas is made to act in the cold upon fiuely-divided gold,' it converts the latter with evolution of heat into auro-auric chloride, Au4 Cl4, a hard, dark-red, hygroscopic salt. Moisture splits this salt into aurous and auric chloride, Au²C14 = AuCl + AuCl³; treatment with water converts it into auric chloride and gold, 3 Au²CI4 = 4 AuC1³ + Au². Aurous chloride, when stirred with water, undergoes a similar decomposition, 3 AuCl = AuCI, + Au,. These decompositions of auro-auric chloride and of aurons chloride furnish the explanation for the practice of moistening an ore before it is treated by the Plattner chlorination-process; practical experience having shown that gaseous chlorine gave an unsatisfactory extraction with dry ore. According to Rose12 fine gold is acted upon more slowly by chlorine than gold containing some base metal, e.g., copper. He also says that small quantities of silver increase the rate of solution, but adds that the coating of silver chloride formed, checks, and finally stops, further action, if the percentage of Silver be increased beyond a certain undetermined amount. Bromine3 acts upon finely-divided gold in a manuer similar to chlorine; the auro-auric bromide, Au²,Br4,, however, is not hygroscopic. Upon treatment with water it is decomposed as is the corresponding chlorine salt. It is generally believed that bromine does not act as energetically upon gold as does chlorine. This seems to be borne out by the results in the leach- +1MASSACHUSETTS INSTITUTE OF TECHNOLOGY, BOSTON, MASS.

Jan 1, 1905

Secretary's Note.—M. Beutter's introductory remarks, being simply a resume of Prof. Hone's paper, with a disclaimer of the intention to criticise it, have been omitted, and the remainder of this contribution lias been somewhat condensed, without omitting any essential statements. M. Beutter, St. Etienne, France* (communication to the Secretary†):—Professor Home observes in $ 47 of his paper that the fluid-compression of steel diminishes piping by forcing the liquid and viscous metal, while the pipe is forming, or after it has formed, into the space so produced, and proceeds to study the different systems of compression, alluding to the four principal ones: Whitworth, Illingmorth, Williams, and Harmet. Having now for many years had in use the last-named process, that of M. Henri Harmet, I shall attempt to explain the difference between it and the three other processes named. The Harmet process does not diminish or close the pipe after it has formed, but prevents it from forming; and I may add that it is the only one of the four which produces this result. It is true that the Whitworth process diminishes the interior hollow by localizing it around the central axis of the ingot, which is afterwards removed by trepanning the hollow forg-ings for which this process has been, I believe, always exclusively used. The Illingworth and Williams processes, which, in my opinion, are applicable only to small ingots, of necessity allow the pipe to form, or (to use the expression of Professor Howe) they allow the surface of the lake of liquid steel to sink into the interior of the ingot, since they involve waiting a certain time before compression, so that (in the case of the Williams process) the ingot-mold can be opened without danger, or (in the case of the Illingworth process) so as to avoid the risk that the steel may enter the grooves produced by the removal of the distance-bars. During the time required for

Jan 1, 1908

By B. F. Tillson, C. M. Haight

I. General Remarks..........................723 1. Location............................723 2. Characteristics of the Orebody..................725 (a) Mineralogical (b) Shape, Strike, Dip, Size, Etc. (1) Ore (2) Country Rock 3. Historical Sketch........................725 11. Mining Method..........................726 1. Outline of Methods Now in Operation............... 726 (a) Stopes (b) Fill . (c) Pillars (d) Slices (e) Transportation (f) Miscellaneous 111. Mining Operations........................727 1. Shaft..............................727 (a) Sinking (b) Dimensions and Equipment, Sketches (1) Size, Inclination. Direction, Etc. (2) Timbering (3) Stations (4) Track (5) Hoisting Equipment (a) Skips (b) Engines and Ropes (c) Idlers (d) Man Cars (6) Loading Pockets (a) Operating Figures (7) Headframe

Jan 1, 1918

By W. D. Robertson, J. -P. Briant, M. Gell

The distribulion of dislocatiorls genevnted during the propagalion of hydrogen-induced cracks in Fe-Si cryslcrls was studied as a funclion of temperature f-110o lo 243°C) and silicorz conlenl (3.1 and 4.2 pct). It zoas found that the clislocntiotl densily and the size of the plctslic zone increased with increasing tempevalnre and decreasing silicon conlent. Furtheruvzove, there was a correlcrtion in the dislocalion patterns formed around cracks that propagated at different tempevattrt-es in cvyslals of diffevent silicon contents such that a 1 pcl itlcverise in silicon content was equivalent to a lemperaluore redziclion of approximately 120°C. The experimenlal YeSnllS were compaved with the results of an elastic-plastic wodel that relates the size of the pluslic .zone to the cvack length, internal pressure, and yield stress. it was found that the clzunges in the dislocctlion cryrays with lemperature and combosition can be e-kplaincd by the lemperatrnre and composilion dependence of the yield stress. An wmtsual feature of this study was the observation of low -temperature noncrystrrllogruphic cracks. PLASTIC relaxation can occur at the edge of a moving crack by the operation of pre-existing dislocation sources or by the creation of new sources in a region of perfect 1attice.l'2 The amount of relaxation in a given crystal depends on the crack velocity and the temperature, and can determine whether a crack propagates in a brittle or a ductile manner.1-3 Tetelman and Robertson4 observed microcracks m Fe-3 pct Si single crystals that formed on (100) planes by the precipitation of hydrogen gas during electrolytic charging at 23°C. The plastic deformation accompanying crack propagation was observed in the form of dislocation etch pits and an extensive analysis has been made of the size, shape, and crystallography of the dislocation arrays5-7 This paper describes the effect of temperature on the plastic deformation generated around hydrogen-induced cracks in Fe-3.1 pct Si and Fe-4.2 pct Si single crystals. The observations are compared with the results of an elastic-plastic model for yielding around a crack containing an internal pressure. 1) EXPERIMENTAL PROCEDURES The composition of the materials used in this study are given in Table I. Single crystals of alloy A and the 4.2 pct Si alloy were grown by the strain-anneal method; crystals of alloy B and the 5.1 pct Si alloy were cut from an ingot grown from the liquid. he ~ingle-cr~stal metallographic specimens had a Cross section of 0.100 by 0.050 in. with a length of at least 3/8 in. Specimens were annealed for 3 hr at

Jan 1, 1968

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

By J. J. Beeson

Page I. PrimaRy MineRalization............................................ 356 1. Introduction..................................................... 356 a. Scope of Work............................................... 356 6. Acknowledgments............................................ 357 c. The Bingham Mining District.................................. 357 d. General Geology.............................................. 357 e. The Utah Copper Mine....................................... 376 f. Field and Laboratory work.................................... 376 2. The Quartz-Monzonite.............................................. 377 3. The Pegmatite Veins.....:.•..............................:........ 378 4. The High-Temperiture Veins.........................-.............:379 5. The Early Hydrotherma! Period.:......................'............ 380 6. The Late Hydrothermal Period................................:.... 385 II. Seconuabx EnricuMENT............................................. 386 . 1. Author's Note;..... ;............................................ 386 2. Factors Governing Enrichment.....................................: 387 3. The Enrichment.................................................... 387 4. The Covellite Enrichment.; .:; ; : .:. :..:.............:................ 388 a. The Capping above the Covellite Ores:....:....................... 388 b. Conclusions Drawn. from a Study of the Capping and the Covellite ; Ores....,.............................................:.....,.' 392 c. Covellite Enrichment at Depth......:......................... : : 392 5. The Chalcocite Enrichment...................................... ; 394 a. The Carbonates in the Capping above .the Chalcocite Ores...:..: .. 394 ' b. The Formation of Chalcocite..:.:. :......:..'...........,......' 394 . 6. Secondary Chalcopyrite and Bornite.............................i ..., . 395 111.- Conclusions as to the Formation.oF the ImpoRtant Sulphides in the Disseminated ORes........................................,.......... 400 I. Primary MiNeRalization 1. Intrdtiction a. Scop. e .of Work.. first part bf, this paper deals with the country rock, its pegihatitic, pneumatolytic', and hydrothermal altektions; also, the effect of magnetite on the deposition of the primary chalcopyrite and pyrite.

Jan 1, 1916

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By Tomek Ulatowski

INTRODUCTION In 1974, Industrial Miners Mexico, S.A. (IMMSA), agent for the borrowers, was the largest privately-held mining, smelting, and refining company in Mexico (accounting for 32% of Mexico's nonferrous metal and coal production in 1974), the fourth largest company in terms of sales, and the second most profitable company in Mexico, excluding government wholly-owned and operated industries. The company was engaged in the mining, smelting and refining of coal, copper, fluorite, gold, lead, silver, zinc and related by-products for domestic consumption and export. A combination of favorable factors led IMMSA to propose an investment plan amounting to US$286 million for 1974 through 1978, of which US$150 million was to be financed. These factors included: Substantial profits in 1973 and 1974 Positive near-term outlook for metal prices Success of the reinvestment program in increasing productivity Substantial additions to proved reserves during 1973-1974 and Fiscal incentives provided by the Mexican government to stimulate investment in the mining industry. The primary purpose of the investment program was to construct a new electrolytic zinc refinery and to expand and modernize many of the company's existing mining and refining facilities. THE BORROWER Company History Compania Miners Mexico, S.A. was incorporated in the city of Monterrey in 1918 as a wholly-owned subsidery of ASARCO Inc. (formerly American Smelting and Refining Company, New York) for the purpose of mining and processing non-ferrous metals and related products. In compliance with the Government's Mexicanization program, ASARCO Inc. divested itself of 51% of its equity in Compania Miners Asarco, S.A. on June 30, 1965. Subsequently, ownership in the divested share was apportioned as follows: 15% ownership in Compania Miners Asarco, S.A. to a group of private investors, and 36% in trust for subsequent public sale. The company's name was changed to Asarco Mexicana, S.A. in 1965. Mexican ownership in Asarco Mexicans, S.A. was increased to 51% in 1967, following the purchase of the 36% share ownership held in trust, and then to 66% in 1974 when ASARCO Inc. divested itself of an additional 15% of its holdings in Asarco Mexicans, S.A. Following its 1974 divestiture of 15% of Asarco Mexicans, S.A., ASARCO Inc's ownership in Asarco Mexicana, S.A. was reduced to 34%. In 1974, the company changed its name for the second time to Industrial Miners Mexico, S.A. (IMMSA). Fiscal Agreement IMMSA entered into a fiscal agreement with the Mexican government in 1969. The agreement, which was renewed in 1974, provided for 100% of the production and export tax corresponding to the federal government with a minimum of 50% of the amount refunded to be reinvested in fixed assets. Further, the agreement permitted the company to

Jan 1, 1985

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By D. T. Peterson, T. Carnahan

The diffusion coejTicients of carbon, nitrogen, and oxyget were determined in $ thorium over the tempernilcre range 1440" io 1715°C. The diffusion coyfiicir?zls are given by: D = 0.022 exp (-27,000/RT) jor carbo)~, D = 0,0032 exp(-l7,00Q/RTj for nitrogen, and D = u.0013 expt(-11,UOU/RT) for oxygen. Cavl~orz was found to increase the hardness of thoriunz nearly linearly with concentration over the range 100 to 1000Ppm carbon. ThORIUM has a fcc structure up to 1365°C and a bcc structure from this temperature to its melting point at 1740°C. Diffusion of carbon, oxygen, and nitrogen in bcc thorium was of interest in connection with the purification of thorium by electrotransport.' In addition, it was possible to measure the diffusion of all three of these interstitial solutes in the same bcc metal. Only in niobium, tantalum, vanadium, and a iron have all three interstitial diffusion coefficients been measured in a given bcc metal. Diffusion coefficients have been measured for carbon and oxygen in a thorium by Peterson2, 3 and for nitrogen by Gerds and Mallett.4 Activation energies for diffusion are reported by the above authors to be 38 kcal per mole for carbon, 22.5 kcal per mole for nitrogen, and 49 kcal per mole for oxygen. Values of the diffusion coefficients of carbon and nitrogen in 3 thorium have been reported by Peterson et al.' However, these were secondary results of their investigation of electrotransport phenomena in thorium and it was hoped that the present study could provide more precise data. EXPERIMENTAL PROCEDURE The specimens used in this study were the well-known pair of semi-infinite bar type. The couple was formed by resistance butt welding two 0.54-cm-diam by 3.0-cm-long bars of thorium together under pure helium, the concentration of the solute being greater in one cylinder than that in the other. The finished couple then contained a concentration step at the weld interface and diffusion proceeded only along the axis of the rod. The thorium used in this study was prepared by the magnesium intermediate alloy method.5 The total impurity content was less than 400 ppm. The major impurities were: carbon, 100 ppm: nitrogen, 50 ppm; and oxygen. 85 ppm. The total metallic impurity content was less than 150 ppm. The high solute concentration portions of the diffusion couples were prepared by adding the solute to the high-purity thorium in a non-consumable electrode arc melting procedure. Carbon and nitrogen were added in the form of spectroscopic graphite and nitrogen gas while a Tho2 layer was dissolved by arc melting to add oxygen. High-purity thorium formed the low concentration portions in the carbon and nitrogen couples. The low oxygen portions were obtained by deoxidizing high-purity thorium with calcium for 3 weeks at 1000°C according to a method reported by Peterson.3 The high C-Th contained 400 ppm C, the high N-Th contained 400 ppm N, the high 0-Th contained 220 ppm 0, and the low 0-Th contained 25 ppm O. The high O-Th was brine-quenched from 1500°C to retain most of the oxygen in solution at room temperature. These concentration levels were all below the solubility limits in 0 thorium at 1400°C. A resistance-heated high-vacuum furnace was used to heat the couples. The samples were mounted horizontally on a tantalum support which had small grooves near each end. Spacer rods of thorium, 0.4 cm in diam, were placed in these grooves to prevent contact between the sample and the tantalum support. This arrangement should have prevented contamination of the sample by contact with the support. In further effort to reduce contamination, the oxygen diffusion couples were sealed inside evacuated outgassed tantalum cylinders lined with thorium foil. Thorium rings around each end of the samples acted as spacers in this case. Pressure during diffusion runs was about 10-6 torr after an initial outgassing stage. Temperature measurements were made by sighting on black body holes in the sample support adjacent to the samples with a Leeds and Northrup disappearing-filament optical pyrometer. Temperatures were constant during a diffusion anneal to ±5C. The observed temperatures were corrected for sight glass absorption after each diffusion run. The pyrometer was checked against a calibrated electronic optical pyrometer and a calibrated tungsten strip lamp with the electronic pyrometer being taken as the standard. All temperature readings agreed to within ±3C over the temperature range 1450" to 1690°C. Time corrections due to diffusion during heating and cooling were necessary because of the short diffusion times. The diffusion times ranged from 6 min for the oxygen sample run at 1690°C to 90 min for the carbon sample run at 1500°C. A series of temperature vs time plots were made for heating and cooling of the samples to the various diffusion temperatures. This data was then used in a method according to shewmon6 to determine the time corrections. The corrections amounted to

Jan 1, 1970

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

A simple reproducible method was developed for determining the ignition temperatures of magnesium and magnesium alloys and by this method magnesium and over 100 magnesium alloys were measured. The ignition temperature of magnesium was determined in O2-SO2, O2-N2 mixtures and in O2 from 0.166 to 10 atm pressure. The ignition temperature of magnesium is generally lowered by alloying and increased by an increase in oxygen pressure. WITH the expanded use of magnesium alloys in industry, ignition temperatures are of considerable importance, especially in heat treating and for service at elevated temperatures. Magnesium alloys exhibit a relatively slow linear oxidation rate up to temperatures near the melting point.' At some critical temperature the rate of oxidation becomes extremely rapid. This high rate of oxidation is accompanied by the emission of light and additional characteristics suggesting a flame. The literature concerning the ignition temperatures of magnesium and magnesium alloys is relatively incomplete and the values reported by various authors are not in agreement. The most probable reasons for this are: 1—The absence of a suitable definition of ignition, and 2—the need of a standardized method of determining the ignition temperatures of inflammable metals and alloys. The exact date of the discovery of the fact that magnesium will ignite and burn is unknown. It is likely that H. Davey encountered this property of the metal during its preparation in 1808. The first reference in the literature specifically on ignition of magnesium is by Lenze, Metz, and Rubens.' They investigated the inflammability of certain magnesium alloys. Brown3-' reported that magnesium ribbon will ignite in air at 507 °C by what was called the rising temperature method. Hartman, Nagy, and Brown" reported that magnesium powder ignites from 475" to 560°C depending on particle size. According to Guise, Mars, and Wilson prolonged heating in air at 427°C of common casting magnesium alloy causes it to ignite. Samples of magnesium alloys were placed directly in the flame of a torch by Carapella and Shaw.' These investigators obtained some evidence of melting prior to ignition. For commercial magnesium, they reported an ignition temperature of 650°C. Their values varied from 450" to 800°C for magnesium alloys. Willmore and Peterson" studied the effect of air velocity, humidity, rate of heating, and foreign metal contact on the ignition temperature of magnesium. They conclude that melting is not a prerequisite for ignition and that the conditions which influence ignition are complex and difficult to analyze. The only quantitative theoretical treatment of the ignition temperatures of magnesium and magnesium

Jan 1, 1952