Search Documents

By A. J. Hatch

Recent disclosures concerning strengthening of anisotropic sheet materials under biaxial stresses are reviewed. This biaxial strengthening has been termed "texture hardening" by Backofen and is related to the normal anisotropy parameter, R. Measurements of R made on three annealed titanium alloys indicate a Ti-4Al alloy will have the greatest potential for texture hardening, followed in order by Ti-5Al-2.5Sn and Ti-6Al-4V. Relative to sheet texture, a review of the deformation mechanisms in titanium alloys would indicate that a preferred orientation for "texture hardening" is where the (0001) pole is normal to the sheet plane. This was confirmed by determination oj (0001) pole figures for the above three alloys. High R values are related to pole figures with (0001) normal to the sheet plane, whereas low R values are related to pole figures with (0001) split in the transverse direction from the sheet normal. PUBLISHED work by Backofen et al. 1 and Hosford and Backofen2 based on hill's' mathematical theory of yielding in anisotropic metals has indicated that significant strength advantages under biaxial stresses are possible in hcp alloys, provided an ideal (0001) [1010] sheet texture exists. This tendency to strengthen under biaxial stresses has been termed "texture hardening".1 It can be quantita- tively characterized by a strain-ratio parameter, R, where R may be determined from the ratio of natural width strain to natural thickness strain as measured on a uniaxial test specimen cut parallel to the rolling direction. If R is greater than 1.0, then strengthening under biaxial tension would be predicted. Considering the a titanium alloys which have an hcp crystal structure, Williams and Eppelsheimer4 have reported that commercial-purity grades deviate from the ideal (0001) sheet texture mainly in an approximate 30-deg rotation of the basal plane, toward the transverse sheet direction. However, McHargue et a1.5 have shown that the angle of rotation of the basal plane is sensitive to alloy content. In particular, a titanium alloy with 3.8 pct Al was reported to have the ideal (0001) [1010] texture after cold rolling. Additionally, Backofen et a1.1 using plane-strain compression tests have reported R values greater than 5.0 for the commercial 0 alloy Ti-5A1-2.Sn (110-AT). In view of these findings, a program was initiated to further determine the potential of commercial Ti-5A1-2.5Sn and an experimental Ti-4A1 alloy with respect to "texture hardening". Also, because of its wide commercial use, Ti-6A1-4V was included in the investigation. BIAXIAL-STRESS THEORY FOR ANISOTROPIC MATERIALS Backofen ef al.,1 based on the mathematical theory of Hi11,3 has introduced the concept of "texture hardening". In this work, it was shown that possi-

Jan 1, 1965

By Yves Dardel

INTRODUCTION SINCE the first determination of Dumas1 in 1880, many authors have tried to measure the solubility of hydrogen in solid aluminum, or at least the amount of dissolved gas in it. However, the interpretation of the results which have been obtained is still difficult. Sieverts,2 then Baukloh and Oesterlen,3 during their gassing experiments could not determine any solubility of hydrogen in solid aluminum. On the other hand, Portevin, Chaudron and Moreau,4 leaving the determination of the hydrogen solubility beyond the scope of their experiments, measured only the amount of gas that they could extract by high voltage positive ion bombardment and found up to 151 cm3 of gas per 100 g of metal. Winterhager,5 by repeated vacuum extraction during severe cold rolling, extracted up to 161 cm3 per 100 g. In both series of experiments, the extracted gas contained chiefly hydrogen with a small amount of nitrogen, carbon monoxide, carbon dioxide and methan. Later, Schmidt and von Schweinitz6 as well as Chaudron and Moreau7 showed the importance of the adsorbed layer of hydrogen, the extracted quantities being proportional to the surface and not to the weight of the sample, when its cleaning was not perfect. In earlier experiments, Steinhauser8 extracted from more massive samples nothing but a little amount (< 0. 5 cm3 per 100 g) of hydrogen, carbon monoxide and methane. Thus, according to these experiments the quantity of dissolved gas is probably very small and the effect of the surface could falsify the results of the extraction. However, owing to the care taken by Chaudron and his coworkers, it was clear that all the hydrogen extracted could not come from the superficial layer, or that the links which bound hydrogen to the surface were so strong that the usual method of cleaning could not destroy them. After the main parts of the experiments reported here had already been carried out, Eborall and Ransley9 published the results which they obtained with an analysor having an accuracy of 0.03 cm3 per 100 g, while that of the usual apparatus was only about 0.2 cm3 per 100 g. During all their experiments the adsorbed layer would have been a difficulty, for the value of the adsorbed hydrogen was approximately equal to that of the dissolved amount. [ ] Since always keeping the same adsorbed layer is very difficult, an error in the correction for the adsorption can be made when using the apparatus of Eborall and Ransley, as well as the earlier apparatus,

Jan 1, 1948

By Eduardo J. Chibas

Location.—The principal manganese-deposits of the Department of Panama, Republic of Colombia, are located almost clue south of Viento Frio, a native village bordering on the Caribbean Sea, and about 45 miles northeast of Colon (Aspinwall). The mining-claims are the Viento Frio, the Carrano, the Nispero, and the Soledad. Each property is to the south of the preceding one in the order mentioned. The first one is about one mile from the coast, and the most southerly boundary of the Soledad is about five miles in a straight line from the same coast-line. I shall confine my remarks to the four properties mentioned and to La Guaca, west of the Carrano, because these are the only ones where mining has so far been done to more or less extent. Manganese has also been found, however, in the neighborhood of these deposits, and a large area adjoining them has been divided into sections and " denounced " as mining-claims. The relative position of the manganese-deposits and Nombre de Dios, the present terminal of the railroad and shipping-port, as well as Viento Frio and the adjacent coast, can

Jan 1, 1898

By R. W. Powers, M. V. Doyle

ThE solution of a diatomic gas such as 0, or N2 in a metal usually follows Sieverts&apos; law; i. e., Here C is the solute concentration at equilibrium and P, the gas pressure. The proportionality constant Ks is also the equilibrium constant for the reaction 1/2 02 (at pressure, P) - 0 (in solution at [21 concentration., C). to use oxygen as an illustrative gas. Sieverts&apos; law is therefore interpreted to indicate that diatomic gases go into metallic solution atomically and that the solute "gas" atoms interact negligibly with each other. Of course, this interpretation is strictly valid only over the temperature interval in which the reaction indicated in [Z] can be investigated. At temperatures several hundreds of degrees below this interval, the possibility of interactions between solute atoms is conceivable. Indeed, from internal-friction measurements some evidence for the existence of groupings of oxygen atoms in tantalum solid solutions was presented a few years ago.1,2 Over a range of solute concentration, the experimental oxygen internal-friction peak in tantalum, measured as a function of temperature at constant frequency of vibration, can be described as the sum of two elemental peaks, each corresponding to a separate relaxation process. At 0.7 cps, the height of the elemental peak found at 137°C is proportional to the oxygen content, whereas the height of the one at 162°C varies as the square of the oxygen concentration. The 137°C peak was presumed to arise from the stress-induced ordering of oxygen atoms among various classes of octahedral sites in the manner proposed by Snoek.3 The 162°C peak was attributed to a somewhat similar stress-induced ordering process, in which each oxygen atom was interacting with a neighboring oxygen atom. Similarly, the experimental peak due to nitrogen in tantalum can also be described as the sum of two peaks. The height of one varies as the nitrogen concentration and the other as the square of this quantity. In fact, some evidence of solute interactions exist for all oxygen and nitrogen solid solutions of Group V transition metals. However, the interaction energy was not obtained previously for any alloy. The determination of this quantity, as a part of a more intensive study of the interaction between oxygen atoms in solid solution in tantalum, is reported in this paper. PRINCIPLE OF THE EXPERIMENT Consider an equilibrium in a solid solution of tantalum between oxygen atoms which are bound together pairwise and those solute oxygen atoms which are not so associated. 20 (Ta) - O2 (Ta) [3]

Jan 1, 1960

By David Cole

THE New Cornelia Copper Co. is mining and treating a &apos;monzonite " porphyry" copper deposit that is all hard rock. The oxidized surface shell, which constitutes the leachable part of the orebody, is measurably more resistent to crushing and comminution processes than is the underlying sulfide portion. The siliceous ribs running through the whole orebody are harder to crush than the main mass and there is no soft crumbly material to furnish the large volume of primary fines that features the crusher feeds of most other porphyry properties. New Cornelia ore reaches the primary crushers with a greater. proportion of large &apos;pieces. When the New Cornelia company first equipped its &apos;property, it used the following machines and flow , scheme to reduce the ore to leaching size:

Jan 1, 1925

By Earl Bardwell

(Butte Meeting, August, 1913.) THE structural relations existing between cuprous oxide and copper were first systematically studied by Heyn1, who suggested that a study of the microstructure of refined copper might be substituted for the analytical methods in vogue for determining the oxygen content of copper coming .;from the refining furnace. Hofman, Green and Yerxa,2 in their paper A Laboratory Study of the Stages in the Refining of Copper, working along the lines suggested by Heyn, showed that a study off the microstructure could be made to yield a correct estimate of the oxygen content of the specimen of refined copper under examination. In order to determine the oxygen content of the specimen of refined copper under examination a photomicrograph was first made. From the relative areas of copper and eutectic, the percentage of cuprous oxide and the corresponding percentage of oxygen were then readily calculated. It was found that the values for oxygen thus obtained corresponded closely with the analytical results. With the idea of utilizing, this method of determining the oxygen content of each charge dipped from the refining furnaces at the Boston & Montana Reduction Plant, the physical testing laboratory was equipped with suitable apparatus for carrying out the work. It may be of interest to describe certain of the methods which have been worked out in, this connection and give such data as have been obtained bearing on the effect of the oxygen content of refined copper upon its conductivity.

Jan 7, 1913

By AIME AIME

A JOINT meeting of the Canadian Institute of Mining and Metallurgy and the American Institute of Mining and Metallurgical Engineers was held at Spokane, Wash., and Cranbrook and Kimberley, B. C., on Oct. 13 to 16, 1926, with a total attendance at one or another or all of the meetings of about 300 members, ladies and guests. At the opening meeting, on Oct. 13, in the Davenport Hotel, Spokane, about 175 were present. The morning was occupied with addresses of welcome by M. H. Sullivan for the Columbia Section, who called on Mayor Charles A. Fleming, President John F. Davies for the Chamber of Commerce, and E. R. Hannibal, president of the Associated Engineers, each of whom heartily welcomed the visitors. Philip N. Moore, former president, and special representative of President Samuel A. Taylor, replied for the A.I.M.E., and Lewis Stockett, president, and Charles A. Banks, chairman, British Columbia Division, Canadian Institute of Mining and Metallurgy, and Henry M. Parks for the visiting A.I.M.E. sections, made appropriate responses on behalf of those they represented. The members and ladies had luncheon with the Associated Engineers. Philip N. Moore addressed the assembly on "The Opportunity of the Engineer"; an excerpt from his address appears on another page. At the afternoon meeting, with Lewis Stockett in the chair, Frank M. Smith was asked to make a brief statement of the proceedings of the Silver Producers Association in Denver. Supplementing his talk by placing a well-prepared statement on "Silver and the Plan of the Royal Commission on Indian Currency and Finance" in the hands of those present, he narrated what had been undertaken by the Silver Producers Association and what they hoped to accomplish.

Jan 1, 1926

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By W. H., Bassett

IN January, 1926, the writer began a study of the commercial value of beryllium in its relation to copper. The purpose of the investigation was not to make a mere laboratory study of the characteristics of beryllium-copper alloys, but to determine under mill conditions the behavior of copper when alloyed with beryllium and when other metals were added to such alloys; in other words, it was considered important to know whether the alloy bars could be hot-rolled or cold-worked, and what limits in composition would have to be established for these two methods of working. Consequently, more stress has been placed on the practical application of the alloys in engineering and commercial use than on a discussion of the metallography of the specimens examined, although this part of the matter has not been entirely neglected. Credit should be first given to G. Oesterheld,1 who, in 1916, published the copper-beryllium equilibrium diagram. Fig. 1 has been copied from the original article with the simple substitution of English words. It will be noted from Fig. 1 that alpha solid solutions are formed, up to about 1.5 per cent. Be (10.5 atom.). The freezing-point curve, after falling from 4.2 per cent. Be (23.5 atom.), enters into a very complicated form over the entire beta region. There is a possible compound, Cu2Be, at about 6.5 per cent. Be (32.3 atom.). The pure gamma range extends from 11.2 to 12.2 per cent. Be. (46.5 to 49 atom.), after which the liquidus rises rapidly to 30 per cent. Be. (75 atom.). The delta solution extends from 25 per cent. to an unknown percentage of beryllium. There is a eutectoid point at 575" C., extending from 1.5 to 11.2 per cent. Be., the maximum time interval of which occurs at 6 per cent. Be. Below this line the beta solution is described as breaking up into alpha and gamma. Microscopically, the eutectiferous alloy thus formed closely resembles pearlite, and requires a high magnification for its resolution.

Jan 1, 1927

By J. Alfred Berger, O. M. Katz

Selected samples of hydrided Zr-Hf alloys were rapidly quenched to voom temperature and exrtrnined metallographically, by X-ray diffraction, and through micro hardness studies to confirm high-temperutuve data Confirming experiments sllowed that there were five phases in this Lernary system: 1) hextrgonal with lattice parameters similar to that of the initia1 Zr-Hf alloy but slightly enlarged due to dissolved hydrogen; 2) fee with properties of a brittle, intermediate, hydride compound; 3) fct with c/a crvoltnd 1.07 and which appeared as a neetilelike precipitale; 4) hexagonal, designated ?, with c/a ratio of 2.37; and 5) orthorhombic, designated X, with a = 4.67, b = 4.49, and c = 5.093 and whose tnicro-st?ruct~ival nppetrl-nnce depcncled o/i, heat lvecrt~r~ent. The tetragonrrl phase never crppeal-erl witkorct the cubic hydricle. Abpecrrtrnce of 0 and A also tlependet on the hafnium content of the zirconium. A previous paper&apos; on the Zr-Hf-H system described the thermochemical data obtained with a high-vacuum, high-sensitivity mirrogravimetric apparatus. This data presented a fairly complete picture of the phase relationships at elevated temperatures. However, it could not establish the actual crystal structures, lattice parameters, or metallographic disposition of the hydride phases. The present complementary study utilizes X-ray powder patterns along with light and electron microscopy to characterize completely the five hydrided phases found in Zr-Hf-H alloys quenched to room temperature. Crystallographic features of the zr-Hf,2,4 zr-H,5-7 and Hf-H8 systems have been summarized in Table I. Designations of a, ß, and ? were retained in the Zr-Hf-H system for the phase regions through which the pressure-composition isotherms always sloped. However, it was not firmly agreed that these were single-phase regions.&apos; In fact, the region designated y always contained a cubic as well as a tetragonal phase after quenching to -196°C. MATERIALS Preparation of the high-purity Zr-Hf alloys has been described.&apos; The four zirconium alloys which were hydrided contained 37 wt pct Hf (23 at. pct), 51 wt pct Hf (37 at. pct), 73 wt pct Hf (58 at. pct), and 91 wt pct Hf (82 at. pct), respectively. These were designated B-2, B-4, B-6, and B-8. Photomicrographs of the initial alloys showed the material to be quite clean as would be expected from the precautions exercised in producing them. However, there were a number of annealing twins but no other subgrain structure. In addition to the four original alloys, fifteen hydrided samples were observed at room temperature. Hydrogen compositions are given at the top of Tables I1 to V. APPARATUS The phases present at elevated temperatures were studied by quenching hydrided samples to room temperature by two different methods, both under vacuum: 1) fast cooling of the sample tubes of the microgravimetric apparatus1&apos;9 with flowing air and 2) rapid quenching into liquid nitrogen. The cooling rate for 1) was 750° to 250°C in 30 sec. Since the microbalance chamber was not designed to permit very rapid cooling of a hydride sample, all liquid-nitrogen quenching was done in an auxiliary experiment. The auxiliary quenching apparatus consisted of a small-bore, high-temperature furnace, a sealed SiO2 tube containing the sample, and a dewar quenching flask filled with liquid nitrogen. The hydrided sample, previously quenched in the microgravimetric reaction chamber, was placed in a platinum boat in a vacuum-degassed SiO2 tube. A zirconium wire getter and degassed SiO2 rod, to reduce the internal volume, were also in the tube. After sealing the tube under vacuum the zirconium getter was heated to absorb the last traces of gas. Only the sample was heated at the reaction temperature for the desired length of time, and then the tube dropped through the opposite end of the furnace into the dewar. A quenching rate of 200" to 400° C per sec was estimated. Analyses of samples after the auxiliary experiment also showed practically no increase in oxygen or nitrogen content from heating in the SiO2 tube. All of the samples were examined at room temperature by the X-ray powder method. The majority of the powder patterns were obtained with double nickel-filtered CuKa radiation after 8- and 16-hr exposures in an 11.48-cm-diam camera. Cobalt and chromium radiation were also used to spread out the high d value end of the Pattern. Such patterns readily identified the minor phases. NO oxide or nitride lines were found. Where sharp back-reflection lines existed it was possible to reduce the

Jan 1, 1965

By C. W. Spencer, F. G. Hochgraf, R. F. Cheney

Columnar grained specimens of nickel, containing 0.25 pct Si and 0.22 pct Mn, have been exposed to liquid bismuth in the temperature range 670° to 1050°C. Under isothermal conditions the liquid penetration rate is constant. The activation energy for the process is 22,000 cal per g-atom. Small amounts of plastic deformation, introduced into specimens prior to exposure, increase the penetration rate. The slou. step in liquid film penetration is associated with a reaction which occurs at or near the leading edge of the film. Either transfer of nickel across the liquid-solid inteqace or diffusion in the grain boundary ahead of the liquid film is suggested. Aliquid metal, if brought into contact with the surface of an unstrained solid metal, will usually penetrate to some extent into the grain boundaries of the solid. Under isothermal conditions the extent of penetration after any particular time of exposure is related to the relative magnitudes of the interfacial tensions concerned.1,2 If the liquid-solid interfacial tension is less than one-half the grain boundary tension the liquid may penetrate at a relatively rapid rate for an indefinite distance into the grain boundary surfaces. If the liquid-solid interfacial tension is greater than one-half the grain boundary energy, liquid penetration occurs at a continually decreasing rate so that after the liquid has penetrated to a relatively short distance below the surface the process essentially ceases.3 Many observations of a qualitative nature concerning inter crystalline attack by liquid metals have been reported, for example, liquid bismuth upon copper,&apos; liquid mercury upon brass,4 and liquid mercury upon nickel.&apos; Scheil and Schessl determined the rate of penetration of liquid bismuth into the grain boundaries of hot rolled copper rod? At constant temperature, penetration rate was found to be independent of the depth penetrated, the rate in- creasing with increasing temperature corresponding to an activation energy of 20,000 cal per g-atom for the process. It was suggested that at lower temperatures the liquid travelled mainly along lines of three grain intersections while at temperatures greater than 1000°C essentially all grain boundary surfaces were covered. Recently, in a study of copper bicrystals having a common [loo] axis it was found that at 649°C bismuth penetrated 22, 25, and 63 deg boundaries while it did not penetrate 2, 12, 15, and 72 deg boundaries.&apos; Elbaum reported that liquid gallium penetrates aluminum grain boundaries to a depth of 0.6 cm after 11 hr at 27°c.8 Assuming that the rate controlling step in the process was diffusion down the liquid film to the specimen surface, a diffusion coefficient of 10-5 cm2 per sec was calculated. This paper reports a study of the penetration of bismuth-nickel liquids into the grain boundaries of a nickel alloy, containing 0.25 pct Si and 0.22 pct Mn as principal alloying elements. The phase diagram

Jan 1, 1962

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By Vsevolod Krivobok

THE re-crystallization of metals has been the subject of much scientific investigation, some of which has resulted in a better understanding of this extremely important and interesting phenomenon. Unfortunately, while many have propounded theories of re-crystallization, but a few have presented experimental evidence as to how it takes place. If this can be determined the question, why re-crystallization occurs, may be answered more definitely. Re-crystallization in single phase metals consists of a complete rearrangement and re-sizing of the grains, of which the structure is composed, while the type of structure remains the same. That is to say, if the structure before re-crystallization is composed of a number of polyhedral grains of different shape and size, a particular spot after re-crystallization will be seen to consist of grains in no way different from the original except in size and shape. The re-crystallized grains may be smaller or larger, depending on the treatment received; and, while the re-crystallization may be brought about by means of heat treatment only in passing through a critical range, yet it is common knowledge that single phase metals subjected to cold working are possessed of a tendency toward re-crystallization, even if the heating does not reach critical range. The study of re-crystallization would, of course, be much easier if we had single crystals of any metal as the original material with which to study the phenomenon of re-crystallization, since it would permit the observation of structural changes at what amounts to enormous magnification, by changing the scale of the specimen. In metals of more normal grain size the crystal boundaries introduce complications, but the process, it may be assumed, is essentially the same. Such an opportunity

Jan 2, 1926

By CHARLES F. DEISS

The total pipe-line runs of petroleum in Indiana during 1945 were 4,114,000 bbl., a decline of nearly 17 per cent below the estimated 4,950,000 bbl. produced in 1944. Drilling activity during the year was centered in Posey and Gibson Counties, where seven new pools were discovered in the state. Four of the pools are in Posey County-Crunk, Farmersville, Jeffries and St. Wendells East-and the other three are in Gibson County-Johnson West, Lysle and Mt. Carmel East.

Jan 1, 1946

By Warren W. Jamar, Philip D. Pearson

IN recent years, there have been many changes in mining operations in the Lake Superior district. To follow these trends on the Menominee Range of Michigan, information has been assembled from all of the iron informatior]mining operations in the area. There are 15 operating underground mines in the Iron River-Crystal Falls area of the Menominee Range. Within the past two years, two idle properties were reopened pasttwoyears,and are now producing, and a third and fourth are being reopened. Also, there are two siliceous openpits operated by independent companies outside this immediate area. Six companies operate the underground mines, employing some 1850 employees. Table I shows pertinent facts about these properties. During 1949, the largest mine in Iron County shipped 571,287 tons, and one of the newer mines shipped 39,378 tons, with a range total to 3,535,-373 tons. Since the Menominee Range was opened in the 1870&apos;s, the mines in Iron County have shipped 85,890,922 tons. From an operator&apos;s viewpoint rather than a geologist&apos;s, the ore is&apos; classified as semi-hard, composed of hematite and limonite. It is not as soft as the ores of the Marquette Range nor is it as hard as the hard ores of the Marquette and Vermillion Ranges. The ore bodies have slate hanging walls and slate footwalls. In most cases the hanging walls and footwalls are soft and high in sulphur. The sulphur comes from pyrite, and these slates will ignite when piled more than 6 to 8 ft high. Ore is mined on this range by: 1—Sub-level stop-ing; 2—Shrinkage stoping; 3—Sub-level caving; 4— Block caving; 5—Top slicing. The predominance of these methods is in the order named. Underground drilling is important in the mining cycle. Some changes made and trends toward future changes fall into four categories: Drill bits, drill steel, drill machines, and compressed air pressures. Several types of bits have been tried and are in use. They include the detachable tungsten carbide, insert bit; the intraset steel bit, which is a conventional steel rod with tungsten carbide insert; the one-use bit; and the multiple-use bit. For many years, detachable multiple-use bits have been standard. In tests conducted recently to im- prove drilling efficiency, this bit was used as the basis for comparison. Under existing conditions, a multiple-use bit can be resharpened about three times before it is discarded. A thorough test of 2-in. tungsten carbide threaded bits was conducted under various ground conditions. 1—The drilled footage ranged from 48 to 600 ft per bit; averaging 357 ft per bit. Under these same conditions, a multiple-use bit ranged from 8 to 80 ft per bit. 2—The bit cost was greater for the insert bit in each case. 3—The average drilling speed for the insert bit was 12 in. in 62 sec and for the multiple-use bit was 12 in. in 64 sec. In a second test, 2V4 -in. tungsten carbide bits with the large 1 3/16-in. thread were used in moderately soft ground on a 152-lb drifting drill on a long feed jumbo. 1—The drilled footage ranged from 450 to 5000 ft per bit, averaging 1810 ft per bit. Under these same conditions, a multiple-use bit averaged 64 ft per bit. 2—The bit cost was reduced by the use of the insert bit. 3—No increase in drilling speed was recorded. 4—Minimum footage obtained was caused by thread failure. To improve the thread life, thread size on the rod was increased and the bit was attached to the rod with a pipe wrench. After this, bits failed in equal proportions because of cracked skirts, broken inserts, and gage loss. Tungsten carbide bits are now used in the operation where this second test was conducted because labor costs were lowered as a result of reducing the number of bits being changed by the miners. At the same operation and under the same conditions as the second test, 1Y4-in. insert bits with standard 1-in. threads were used. These bits did not drill much more than 300 ft before thread failure and were then welded to the rods and used until total failure. Sometimes this footage was considerable, sometimes it was not. Chisel-type 2%-in. insert bits were

Jan 1, 1952

By AIME AIME

BECAUSE of its unequalled skill, your country in- creased its production until, in 1913, it produced 40 per cent. of the world&apos;s consumption of coal, iron ore, and cast iron; 45 per cent. of the steel; and 60 per cent. of the copper. Your industrial effort, in a general manner and your mining effort in particular, has been tremendous. In the general economy of the world, you occupy an incomparable position of power and action. All your curves of production, mineralogical, metallurgical, financial, commercial, have taken terrific trigonometrical tangents and you will easily under- stand the sorry position of your competitors. I must, therefore, pay a tribute of homage arid admiration to you all who, each in his sphere, have been the artisans of such prosperity and my earnest wish is that you continue in this way.

Jan 1, 1920

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104&apos;c per sec for 0.010 in thick specimens, as calculated from Newton&apos;s law of heat flow2 using a heat transfer coefficient of 25 ft-&apos;. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.&apos; The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.&apos; The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By AIME AIME

CORROSION of tanks, pipes and other equipment in the oil fields is becoming worse as the production of high- sulfur crudes in the Texas panhandle and west Texas areas increases. It has been estimated that .in certain fields of that State one tank out of every five has to be replaced every year because of the high sulfur content of the crude. One suggested method for combating tank corrosion is the use of .materials which have a high resistance to the corrosive action of hydrogen sulfide and high-sulfur crudes; aluminum is one of these materials. As a result, the United

Jan 1, 1929

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors&apos; present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951