Search Documents

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By M. Baeyertz

SINCE 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer1, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallography. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types.

Jan 1, 1930

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve -Engineers. AMBLER, HARRY A., Second Training Camp, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers' Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22c1 Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers' Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 10, 1917

By C. Altstetter, Y. Huang, E. de Lamotte

Nitrogen was introduced into pure niobium (colutn-bium) and dilute Nb- Zr alloy wires by equilibration with pure nitrogen gas at high temperatures. Room-temperature hardness was correlated with the alloy composition, heat treatment, and microstructure. Hardness was found to be most sensitive to the amount of nitrogen in solution; however, a significant hardening up to 500 Dph look place upon aging of quenched alloys. A coarse dispersion of nitride did not significantly increase the hardness of the material though the nitride was found to have a hardness of 1400 Khn. BY now the marked effect of nitrogen on the properties of bcc refractorv metals is we ll-documented. There are few studies, however, in which the state of the solute has been carefully controlled. Indeed, the composition-temperature-pressure relationships in nitrogen-refractory metal systems have been determined precisely for only niobium and tantalum.'-4 Most investigations on niobium have dealt with alloys High-nitrogen alloys cleaved on (100) planes and had negligible ductility. Precipitation was found to occur in either a discontinuous or a continuous fashion, depending on the composition and cooling rates. Upon cooling, the precipitation first proceeded discontinu-ously by the nucleation of nilride needles at subbound-aries and subsequent growth of a two-phase microcon-stituent. At lower temperatures continuous precipitation occurred in the subgrain interior ahead of the discontinuous precipitation interface. containing nitrogen, carbon, and oxygen in significant but uncontrolled and, in several instances, undetermined amounts. Thus, there has been some uncertainty regarding the presence and the distribution of precipitates. This paper presents results which relate the hardness and microstructure to the heat treatment and nitrogen content of niobium and Nb-Zr alloys. Niobium rod* produced by the Wah Chang Corp.

Jan 1, 1968

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

Jan 5, 1976

By Magnus Troilius

SINCE the discussion on steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results obtained by different chemists. To any one having the least acquaintance with chemistry, it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application of chemistry to steelrail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it occurred to me, two years ago, that I could not do better than start a laboratory of my own, and engage one of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus obtain without delay thoroughly accurate determinations. Moreover, in order to carry on the operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as mas found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By C. G. Goetzel

E. V. Crane.*—I want to ask Dr. Goetzel concerning the control of atmosphere in heating and pressing. Was the heating and pressing done in the die, or were the two kept separate there? C. G. Goetzel.—The setup used for this investigation implied heating the die to the temperature at which the work was to proceed, introducing a preformed compact into the hot die. The atmosphere was supplied through an annular chamber from which it passed through two holes into the die cavity. E. V. CRane.—The compact was not preheated? C. G. Goetzel.—The compact was not preheated. Tee Chairman.—In the course of recent studies on the effect of time of heating upon the tensile strength and hardness, I have observed that there is often a maximum in tensile strength and hardness reached before complete homogenization has been attained. The magnitude of each mechanical Property changes rapidly with time in the early stages of sintering, the more so as temperature increases. For these reasons it seems that the comparison of values obtained by heating for the same time at a series of temperatures may be deceptive. Not only may those heated at higher temperatures give higher tensile readings, but the reverse may be true if the maximum in the tensile strength versus time curve has been passed. A better basis for comparison would be that of equal degree of diffusion. C' " Goetzel.—Thank you, Professor Rhines, for this interesting contribution. I would like to add here that I have noticed a similar effect with straight copper. There is, of course, the possibility that this maximum in hardness and tensile strength may be caused by work-hardening.

Jan 1, 1945

By John Norton

THE tremendous increase in the use of metals that have been prepared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations, It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing.

Jan 1, 1932

By John Griffen

THE modern anthracite breaker or washery uses almost completely a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids-coal, slate, pyrite, and clay-and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers, changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, require finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely and store and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,1 from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite

Jan 9, 1921

By Maurice Ewing

THE purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for, this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data sum-marized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the oppor-tunity for checking results so thoroughly is given. In the second place, the fact that recent commentators 1.2.1 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1922, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By Harvey Brooks

Jan 1, 1963

By S. L. Hoyt

The writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + b range, first described in 1913. These notes are offered, not at all as the final explanation 'of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520' C. and the other at about 600" C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600" C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + B range and increased in magnitude with the amount of B up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + B field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 1, 1919

By Milton H. Fies

Although pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson's soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was an undertaking of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state. Coke for foundry use was first made in Alabama in 1855. It was 21 years later, however, in 1876, that pig iron was made from Alabama ore with Alabama coal.

Jan 1, 1925

THE. extraordinary volume of work done in this period, and the multiplicity of subject matter, make a year-by-year historical account undesirable, if the account is not to be an assembly of unrelated fragments. We shall, instead, undertake to narrate the development in this period of each of the branches of the subject separately, hoping that their interrelations will be self-evident. There is a certain arbitrariness in the selection of subject matter in the following sections. The development of important engineering alloys-for example, high-speed steel-is disregarded, for it is the primary purpose of this account to relate the advances in ideas, the growth of the science of metals; other historical accounts relate these parallel advances. Nor are advances in techniques stressed, though occasionally the most important are noted; nor is the progress described in allied fields such as welding, cutting, etc.; for though these developments have very frequently made possible the advances herein related, they are far too numerous to recount in anything short of a ponderous volume. There is a more serious arbitrariness, however; it is not an easy matter to draw the boundaries of physical metallurgy, and some contiguous subjects have been omitted that perhaps should have been included, such as, for example, corrosion, gases in metals, the magnetic behavior of metals and alloys, and certain other fields in the physics of metals. REACTIONS IN ALLOYS--DIFFUSION Many of the reactions occurring in alloys proceed by the operation of the process of diffusion in the solid state: the annealing of mixed powders to form alloys, the homogenization of castings or forgings, the freezing of alloys, the treatment of clad metals, the loss

Jan 1, 1948

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

The term "timbered stope" is here meant to denote stopes in which timbering is the predominant feature of the mining method. Stopes with stull sets, as in the Hecla mine, are types of timbered stopes; these types are probably the best-known. Timbering stopes by means of square sets is not as common as formerly, as the system is not often necessary, yet there are good examples and large tonnages are being mined by the method. The square set may be utilized in ordinary overhand stopes if the orebody is suitable. At some mines, square sets have been abandoned in favor of top-slicing; and at others, the square set has superseded horizontal cut and backfilling. A drift, either in the wall or orebody, is necessary before opening the sill floor. In wide deposits, there may be a grillage of drifts and crosscuts, and at least one raise to the level above is needed in each stope for ventilation and handling timbers and filling. The square sets are filled with waste rock from the hanging wall, sorted from the ore, from development work, or from the level above. As a rule, little timber is recovered. The examples include the Butte district, Mother Lode of California, Bunker Hill & Sullivan, Hecla, and Morning mines.

Jan 1, 1925