Search Documents

By A. Phillips, D. H. Killpatrick, V. Kerlins

The tensile failure of two dispersion-strengthened Ni-20 Cr alloys was studied and compared to the fracture of a similar alloy with no dispersoid. The fracture characteristics were studied using electron fruc-tography and transmission electron microscopy. In all three cases, the mode of failure was found to be microvoid coalescence. The failure in the dispersion-strengthened alloys was found to have initiated at the particles. The size of the dimples in the fracto-graphs was found to be related to the spacing of the particles, but not to the total elongation before failure. The elongation before failure was found to be related only to the amount of dispersed phase. These results are compared to those predicted by a theoretical model of ductile failure. THE continually increasing strength requirements for creep-resistant materials capable of long life at service temperatures above 1600"F (875"C) have developed considerable interest in dispersion-strengthened nickel-base alloys. The high yield strength of these alloys results from the presence of a dispersion of fine particles of thoria which act to impede the normal motion of dislocations. Many theories have been presented to explain the role of the dispersion in the strengthening of these alloys. A good review of these theories is presented by Ansell.' The ultimate strength of such alloys is not only related to mechanisms raising the yield strength, but also to the amount of work-hardening which occurs. This work-hardening is determined by the work-hardening rate and the amount of plastic strain before failure. Since fracture limits the amount of plastic strain, a study was undertaken to gain a better understanding of the fracture mechanisms in these alloys. Electron fractography and transmission electron microscopy were used to study the fracture characteristics in two dispersion-strengthened alloys and one similar alloy containing no dispersoid. These results are related to the tensile properties of the dispersion-strengthened alloys at room temperature and at 2000°F (1095°C). The results are also related to a theory for ductile fracture. 1) PROCEDURE Standard tensile specimens were made from 0.020-in. (0.051-cm) sheets of three different Ni-Cr alloys. The alloys had nominal compositions of Ni-20Cr, Ni-20Cr-2Th0,, and Ni-2OCr-4Th0,. All alloys were supplied in an annealed condition. The specimens were fractured in tension at room temperature to determine the effect of the dispersed thoria on the fracture appearance. The tensile properties were determined from the average of a minimum of three ten- sile specimens for each condition tested. The fracture surface of all of the alloys was examined by electron microscopy using standard two-stage plastic-carbon replica techniques. Thin foils of the dispersion-strengthened alloys were used to investigate the size and spacings of the dispersion particles, and to investigate sections of the 2 pct thoria alloy taken from areas of the specimen adjacent to the fracture surface. The thin foils were mechanically ground to 0.010 in. (0.025 cm) and then chemically polished to approximately 0.001 in. (0.003 cm) in a solution of 29 g of ferric chloride and 10 ml hydrochloric acid in a liter of water. The polishing solution was maintained at 150"F (65°C) during the thinning operation. The final thinning of the foil was done electrolytically using a solution of 700 ml ethanol, 100 ml 2-butoxy eth-anol, 120 ml distilled water, and 78 ml perchloric acid (70 pct). The potential was maintained at 15 v and the bath temperature at -20°~ (-29°C) during the thinning operation. The final thickness of the foil was approximately l000A as determined from the width of twins boundaries observed in many of the foils. 2) RESULTS AND DISCUSSION The electron fractographs of the fracture surfaces of the alloys are shown in Figs. 1, 2, and 3. The normal interpretation of this type of fractographz is that, as a result of the difference between elastic and plastic properties of the matrix and the particles or other inhomogeneities in the alloy, microvoids are formed

Jan 1, 1969

THE metal iron has physical arid chemical properties which are some- what different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron the former being the ordinary form at room temperature. When heated above the "A2 point," 769 C (1416 F), the metal becomes nonmagnetic, and at the "A3 point," 911 C (1672 F), it undergoes a change in crystalline form to become gamma iron. 111 the range 769 to 911 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1392 C (2538 F), it changes into delta (d) iron, which is identical with beta or nonmagnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1536 C (2797 F); the melting point is generally lowered by alloys or impurities. PHYSICAL AND THERMAL PROPERTIES OF IRON Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A3 point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly with the range of stability of a given form, but this is not always true. For ex- ample, the specific heat reaches a sharp maximum at the A2 point al- though no transformation occurs. (See Fig. 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an appreciable extent. Table 16-2 contains a list of the common elements classified with respect to their solubility in liquid iron. Those which are very soluble or practically insoluble require no further discussion, but several of the nonmetals that are gases and exhibit limited solubility are of considerable importance to us and merit more detailed consideration.

Jan 1, 1964

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By Gerhard Derge

Metallurgists have used borax as a fluxing agent traditionally, but until recently elemental boron has played an insignificant role as an alloying element. Neither the metal nor its compounds have been regarded as important metallurgical materials and there is a surprising lack of knowledge concerning their metallurgical behavior. The new applications to steel-making of both boron and borates, which arose in part from wartime incentives and restrictions, have been seriously handicapped by this lack of data. For example, rasorite, a naturally occurring sodium borate, has been shown to be an effective substitute for aluminum as a ladle deoxi-dizer in rimming steels.' Likewise, the effectiveness of boron as an alloying agent has been demonstrated,2,3 giving deep hardening when used in restricted amounts. The exploitation of both of these uses has been retarded by the difficulty of attaining suitable metallurgical control. Recognizing that the most important information required was a knowledge of the equilibrium between boron and oxygen dissolved in liquid iron. Gurry4 calculated this relation from the best thermal data available. However, estimates of the entropy of melting of boron, the activity coefficient of boron in liquid iron and the activity coefficient of B2O3 in slag were involved, and experimental work on this problem was obviously desirable. The experiments to be described were planned to establish the boron-oxygen relations in liquid iron and to demonstrate at the same time the ferroborate slag compositions in equilibrium with various amounts of oxygen in liquid iron. Accordingly, slags containing varying proportions of iron and boron oxides were held in contact with molten iron, and samples of both slag and metal were analyzed. The limitations upon the accuracy of the data will be considered, but in a practical sense the oxygen levels that can be attained in iron by iron borate slags, and the amounts of boron in iron at these oxygen levels were established. Experimental Procedure No entirely suitable refractory was found for the mixtures of iron oxide and boron oxide used as slags. Crucibles of silica, magnesia, Ramix, beryllia, and zirconia were all tried unsuccessfully. The must satisfactory method discovered for handling them was the rotating-crucible technique, which creates a parabolic crucible of liquid iron.5,6 Even this was not entirely successful, for at steelmaking temperatures (1600°C.) the slags had such a low surface tension that they crept up to the refractory and slowly dissolved it. These difficulties made it impossible to maintain a constant slag composition for an unlimited period Of time. However, by using the rotating technique, short runs could be made in

Jan 1, 1947

By John L. Lamont, Walter Crafts

SELECTION of an alloy steel for a heat-treated article has been facilitated by methods for the calculation of hardenability,1 as-quenched hardness,2,3 and tempered tensile strength.4 Ductility and toughness may also be estimated if the steel is completely hardened on quenching,5,6 and the present study was carried out in order to develop a basis for estimating the Izod impact strength of partially hardened steel. The investigation was directed toward the prediction of Izod impact strength in steels of normal commercial quality without consideration of special compositions or heat-treatments that might produce abnormal brittleness. It was found that Izod impact strength of alloy steel is controlled by hardness, degree of hardening on quenching, and grain size. In fine-grained steels the impact strength for any given degree of hardening is inversely proportional to the tempered Rockwell C hardness, and the relation of impact strength to hardness is lowered by incomplete hardening. Calculation of the tensile strength and impact strength of heat-treating steels has shown that, except at very high strengths, tensile strength is raised by alloys without loss of impact strength whereas the tensile strength gained by higher carbon contents tends to be accompanied by a disproportionate loss of toughness. Plain carbon steels give relatively low and unpredictable impact strength. The calculation is sufficiently accurate to be helpful in the selection of alloy steel, and common grades of alloy steel have been evaluated with respect to combinations of tensile strength and impact strength attainable after heat-treatment in sections from I to 4 in. in diameter. PROCEDURE The study of the relation of hardness to impact strength was based on test data derived from 24 heats from four producers. The steels included the following SAE and AISI compositions: 1020, 1o30, 1040, 1340, 3310, 3316, 4320, 4330, 4340, 8620, 8630, 8640, 8720, 8730, 8740, 9310, 9317, 9440, 9917 and three high-alloy chromium-nickel-molybdenum steels. As far as is known, the steels tested were of normal commercial quality. They were supplied in 4-in. sections, which were forged to smaller sizes, prenormalized, and machined to final dimensions. Heat-treatment was carried out by heating to the usual austenitizing temperature for the grade of steel, holding for one hour per inch of thickness and quenching in still oil at room temperature. Previous work had indicated that this quenching treatment approximates a severity of H = 0.35. The bars were tempered as follows: ½ in., I in., and I 5/8 in., 2 hr; 2 ½ in., 3 hr; 4 in., 5 hr. All bars were air-cooled from the tempering tem-

Jan 1, 1947

By Scott Howard

MANGANESE being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Ar3 transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the Ar3 transformation occurs at a temperature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3 quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Ar3 point as falling to 0° C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer,2 using alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 percent for the manganese content at which Ar3 is depressed to 0° C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson's treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson's relation for the strain energy can be de-

Jan 1, 1955

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By A. B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drillholes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 1/4-in. diam, on 25-ft and 100-ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals. Only radon"", a member of the uranium'" series, was measured in this investigation. Radon is one of the chemically inert noble gases and is radioactive by alpha particle emission with a half life of about four days. In this discussion, amounts of radon are expressed in microcuries (1 microcurie equals 37,-000 disintegrations per sec) and concentrations of radon are expressed in microcuries per liter of drillhole air. Samples of air were obtained by lowering a sampling device (Fig. 2) into a drillhole and actuating the device at the desired depth. It was then raised to the surface and the sample was transferred to a storage tube. Within two days the sample was transferred to an ionization chamber, and the activ- ity of radon and its short-lived daughter products was measured at radioactive equilibrium with a vibrating-reed electrometer. The measurements were corrected back to the time of collection and involve errors estimated generally not to exceed + 5 pct to —15 pct. Radon Behavior in a Covered Hole: Fig. 3, a typical log of radon concentration vs depth in the covered drillhole, was made by using values of radon concentration at discrete depths. Continuous logs of alpha-particle radiation in the drillholes showed that such radon logs depict the continuous variation of radon concentration with depth quite accurately. Three features of radon logs were noted: 1) maximum

Jan 1, 1960

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By Homer F. Staley, C. P. Karr

The casting alloy 88 copper, 10 tin, 2 zinc, commonly known in England as Admiralty metal and in this country as Government bronze, gun metal, or Naval Department composition G, has, at its best, many valuable properties. However, its physical properties are known to vary widely with slight changes in method of manufacture of the castings, such as slight variations in composition, variation in pouring temperature, kind of mold used, method of pouring and gating of molds, size and shape of castings, amount and kind of heat treatment, and so forth.' The microstructure of castings made from this alloy is influenced by slight variations of composition, rate of cooling, and kind and length of heat treatment. This is best understood by reference to the equilibrium diagram. The part of the diagram in which we are interested and the effect of the thermal equilibrium relations on the physical properties of the alloy 88 copper, 10 tin, 2 zinc, have been discussed by Hoyt, Campbell, Primrose, and Rawdon.2 In Fig. 1 is given the equilibrium diagram of the copper-tin alloys. Briefly stated, the relations of composition and temperature changes are as follows. Compositions between A and a consist of but one constit ent—the a bronze, which is a solid solution of copper and tin, rich in copper. On cooling from the molten state these compositions gradually crystallize, at temperatures above 790°, into a mass of interwoven treelike crystals or dendrites. The cores of the dendrites are rich in copper and the percentage of tin gradually increases as the surfaces are approached. AS cooling progresses, after a11 the metal has crystallized, no further changes occur in the crystals other than diffusion within the crystals, which tends to erase the dendritic pattern and to render the structure more homogeneous. * Metallurgical Ceramist, U. S. Bureau of Standards, Associate Physicist, U. 8. Bureau of Standards. A. D. Flinn: Iron. Age (1915) 96, 1292-3. C. P. Karr: U. S. Bureau of Standards Tech. Paper 59, Pt. 1. S. L. Hoyt: Enging. (1913) 96, 667-7, 704-5. William Campbell: Trans. Am. Inst. Met. (1912) 6, 158-172. H. S. Primrose: Metal Ind. (1916) 14, 202-4. H. S. Rawdon: U. S. Bureau of Standards Tech. Paper 59, Pt. 11.

Jan 1, 1921

By B. S. Blakeney, E. P. Abrahamson II

The effect of the transition elements in binary solid-solution additions upon the recrystallization temperature of iron has been investigated. All these elements immediately raised the temperature, the majority having their greatest effect in less than 0.10 at. pct. A correlation is noted between the rate of change of recrystallization temperature with atomic percent solute and the electron configuration of the solute element. THE work of Abrahamson and rant' on binary chromium-base alloys indicated that a correspondence existed between the effect of each solute element on the brittle-to-ductile transition temperature of chromium and the ground-state electron configuration of the element added. This was felt to be a bonding phenomenon and would be expected to be observed in measurements of other properties involving the breaking or exchange of atomic bonds. From this work it was postulated that a like correspondence should be found for other properties of binary alloys, such as recrystallization. This study is an effort to check this postulation using binary solid-solution iron-base alloys. Previously, the majority of recrystallization studies were carried out on steels. However, Tammann2 investigated the recrystallization of iron as effected by Co, Ni, Si, Mn, Mo, and Cr and stated that elements with the same crystal structure at room temperature as iron appeared to be more effective in raising the recrystallization temperature. Austin, Luini, and Lindsay3 studied the effects of Ni, Cr, Mn, Co, Si, and Mo on cold rolling and annealing, but noted no trend. Abrahamson and rant,' in their work on the effect of both substitutional and interstitial elements upon the brittle-to-ductile transition of chromium, have shown that the outer electron configuration in the ground state of the solute element appears to be the prime determinant of the transition temperature. PROCEDURE All alloys were made using 99.95 + pct Fe with 0.02 wt pct 0, 0.004 pct C, and 0.001 pct N. All alloying elements were 99.9 + percent pure. Metal-lographically the alloys, out to at least 0.1 at. pct, appeared to be in solid solution. Though several published phase diagrams tend to dispute this.4 All alloys were arc melted six times and cast into square 400-g ingots under an argon atmosphere.

Jan 1, 1961

By N. H. Emmons

THE work of a consulting engineer or manager, when controlling mining-operations, requires that he have all the information concerning the mine in as concise a form as possible, and as the ore-reserves and their depletion and enlargement are the vital points to be studied, it is well to have them kept up to date and in some convenient form. The present paper describes a method adopted by me, which shows in a very clear manner the ore-reserves in a mine. The case illustrated is that of a vein near enough to the vertical for the vertical elevation of the mine to be the main working-map. A flat ore-body would be represented on a similar plat, but instead of the horizontal thickness of the vein being shown in the circles, the vertical thickness would be inserted. Fig. 1 represents an ideal longitudinal elevation of a mine, plotted in the ordinary way, using 100-ft. blocks and section-lines. In a mine where the block-numbers are posted by the engineer underground, the system of keeping the ore-tonnages extracted from the different blocks is easily maintained, and the actual tonnages of ore extracted can be kept so that the surveyor can have a check on his estimate from time to time. The ore-reserve sheet, Fig. 2, should be the same size as the map it is to accompany. Each square is used for the description of the ore-reserve in the block it corresponds to on the elevation. Where the section-lines cross the levels a circle is drawn, in which are written the widths of ore at that point, these widths being used in the calculations of each block cornering in the circle. It has been found convenient to show the figures in black in the lower half of the circle when the actual widths of ore are known, and when it is necessary to make up the figures of probable ore, as at the time of making

Jun 1, 1912

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By R. T. Pepper

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80° to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- ° diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By R. A. Bergier

The Transactions of the Institute contain nothing, as yet, on the subject of pocket-compasses; and in the belief that American miners, explorers, geologists, and engineers will gladly welcome any infor mation about new forms of apparatus, simple in construction and adapted to rapid use, I offer a short description of an improved French combination pocket-compass, which, if once introduced into use, would seem likely to supersede similar instrumens of older pattern. The instrument in my possession I owe to the kindness of M. G. de.La Bouglise, of Paris. The frame of the compass is a double-bottomed box, 2 1/2 inches square and 9/16 of an inch high, made of white metal, and with its sur faces very carefully planed. The sides of the box make true right angles with each other. Two sides are parallel with, and two are normal to, the north and south line of the principal graduation. The bottom is accurately planed, so that the instrument will lie true on a plane surface. A glass, 2 3/8 inches in diameter, is set in the top plate. The graduation for the needle is engraved on the upper face of a ring, connected with the flat disk, in which the center-pin is in serted. Between this disk and the bottom of the box there is a hollow space a quarter of an inch deep. The needle is 1 7/8 inches in length, and can be balanced by means of a small sliding piece of metal. The graduation extends from 0° to 360°, reading from right to left. The stopping of the needle is effected by a screw, A, on the side of the box near the handle, H (Fig. 1). There is also a clinometer attachment, the graduation for which is engraved on the upper face of the silver-plated disk. The compass has two sights. The north sight, B, is a simple pin, a little more than an inch high, which, when not in use, is kept folded down, and is partially protected by the exterior sliding-plate, C. When raised for use, the sight is stopped in a vertical position by a projecting pin attached to the side of the box.. The south sight, D, is connected with the handle, H, and the sight and handle

Jan 1, 1890

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

By W. R. Barclay

IN MY general contact with industry I have become more and more impressed with the need for the closest possible co-operation between engineers and metallurgists, and particularly with the need for appreciation of the work that each group is doing to assist the other. Also, I am convinced that from time to time it. is vitally important to a true perspective of human progress in all its branches, and certainly a salutary corrective of undue optimism and pessimism to endeavor to carry the mind hack over certain periods in the advance of technical knowledge, and form some kind of broad estimate of what has been accomplished in the application of science to industry in the fields with which we, as individuals or groups, may for the time being be concerned. We cannot without some appreciable mental effort realize what our forerunners have dine For us. If the young engineer or metallurgist entering industry today could be suddenly transported to a quarter of a century ago, and be compelled to work with the materials then available and within the limitations of knowledge then attained, he would, on his return to present-day life, have a much greater appreciation of what has been accomplished before lie arrived on the scene, and, what is even more important, a far more acute sense of its inherent value to his profession. I propose here merely to indulge in a general summary of the subject of improved engineering metals and alloys rather than in details, and to deal exclusively with developments within my own experience.

Jan 1, 1938