Search Documents

By J. A. Roberson, A. M. Adair

A plate of an 18 pct Ni (250 grade) maraging steel was homogenized, cold rolled, and re crystallized to produce a fine grained, homogeneous structure. The strength properties were then measured as a function of cold rollinq prior to aging. Material in the solution heat treated condition exhibited substantial strengthening from cold rolling. The strength increase and the rate of strengthening were proportional to the amount of cold work. This benefit, of up to 50 ksi, was retained during aging for 3 hr at 900°F. The structures produced by cold rolling and aging have been systematically investigated by transmission electron microscopy. The dislocation debris produced by cold work influences the morphology and distribution of precipitate particles as well as the rate of precipitation. An essential feature of the high nickel maraging steels is a martensitic transformation from y to a with the resultant production of a supersaturated bcc solid solution. This solution decomposes to form precipitates during a subsequent aging treatment.' The martensitic transformation in low carbon Fe-Ni alloys and the mechanical properties of these alloys have been studied extensively.2"4 The carbon content of maraging steel is kept very low to avoid the embrittling Fe3C phase and to minimize the acicular, or twinned martensite common to high carbon steels. Maraging steels are usually strengthened only by heat treatment, but cold working is also quite effective in this respect as was shown by Decker, Eash, and Goldman,' Kula and Hickey,5 and the present work. There is, however, some disagreement between the present results and those of Kula and Hickey. Because of their unusual combination of strength and toughness, the maraging steels are suitable for applications where reliability at high stress levels is required. The strength level is achieved through a combination of solid solution hardening,' substructure hardening,3 and precipitation hardening,6 of which the last is the most important. The toughness of these steels has been reported to be a result of the absence of brittle grain boundary precipitates,7 and the fact that the matrix is a massive martensite rather than a twinned martensite.' One of the problems in the manufacture and use of maraging steel has been its tendency to develop laminations in sheets parallel to the rolling plane.9,10 The present investigation was intended to determine whether or not an improvement in the microstructure of this steel by thermomechani-cal processing would improve mechanical properties. I) EXPERIMENTAL PROCEDURES A plate ($ in. thick) of an 18 pct Ni-250 grade maraging steel* was obtained and examined metallo- "Analysis, wt pct: 18.1 Ni, 8.6 Co, 5.3 Mo, 0.4 Ti, 0.07 Mn, 0.05 Cr, 0.05 Si, 0.002B. 0.1 Cu. 0.05 Al. 0.002 Zr, 0.016 C, balance Fe. graphically. It was found to contain laminations as described by previous investigators. This plate was then annealed at 2100°F for 24 hr to promote homogeneity. Pilot studies on small coupons had shown that this was the minimum temperature required to accomplish homogenization in 24 hr. Since this treatment caused excessive grain growth, the steel was subsequently cold rolled and recrystallized. Cold rolling was accomplished at about 5 pct per pass to a total reduction of 66 pct. The standard solution annealing treatment (1 hr at 1500°F) was adequate to cause recrystallization of the cold worked steel. The recrystallized steel was then cold rolled and ground by various amounts to produce specimens with uniform thickness and selected amounts of cold rolling. All tensile specimens with less than 90 pct cold reduction were ground to a thickness of 0.050 in. Specimens with 90 pct cold reduction were 0.025 in. thick. All

Jan 1, 1970

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By W. C. Thurber, C. J. McHargue

THE deformation textures of metals have been extensively studied because of both the practical implications in metal fabrication and the fundamental insight into the behavior of the metal during deformation. Most studies have been concerned with pure metals or solid-solution alloys and relatively little attention has been directed toward more complex alloy systems. Barrett' and Brick2 have summarized work on multiphase systems in terms of the relative ease of deformation of the phases. Thus, if the phases are deformed about equally, each develops its usual texture for the particular fabrication process. This behavior has been reported for Ag-Cu and Cd-Zn alloys3 and 62-38 brass.4 A dispersion of hard particles in a softer matrix interferes with the normal reorientation of the matrix lattice during deformation, thus distorting the texture or in some cases preventing its development. Increasing the amount of carbon in steel has been observed to increase the randomness of the ferrite5 and almost random textures have been reported for A1-12 pct Si eutectic alloy wires.6 It has also been noted that if the second phase is platelike, deformation causes the platelets to line up in a common direction. The present work concerns a quantitative study of the deformation textures in aluminum-uranium alloys containing 5 or 13 wt pct U. Alloys in this composition range are characterized by a pure aluminum matrix in which the intermetallic compound UA14, is dispersed. From a fundamental standpoint, this system affords the opportunity for studying the effects of a dispersed phase on texture development in an essentially pure metal matrix. Further, these alloys are commonly used as fuels for nuclear research and testing reactors, and a knowledge of the preferred orientation may be useful in evaluating physical and mechanical properties as well as response to fabrication. The deformation textures in sheets of aluminum (99.996 pct), Al-5 pct U alloy, and Al-13 pct U alloy were determined for reductions in thickness of 90 pct by cold rolling. The texture in an alloy rod of the latter composition which had been extruded at 455°C was also determined. It can be readily ascertained from the aluminum-uranium phase diagram that the 5 pct U alloy is hypoeutectic and contains 7.3 wt pct (3.4 vol. pct) UAl4. The 13 pct U alloy has the eutectic composition and contains 18.9 wt pct (9.4 vol. pct) UAl,; however, because of nonequilibrium solidification conditions, the typical eutectic microstructure was not developed. The alloys were prepared by open-air melting in graphite crucibles. The slab castings were cropped and cold reduced 90 pct in thickness on a two-high mill. The slabs were reversed after each pass. Although the uranium-bearing alloys exhibited edge cracking, they could be cold rolled to the desired thickness. Small coupons 1.5 by 0.75 by 0.1 in. thick were sheared from the center of the rolled plate with a major axis parallel to the rolling direction. To obtain a specimen of sufficient thickness for machining of the X-ray diffraction specimen, three coupons were laminated into a single three-ply sandwich with a suitable adhesive. Adhesives which could be cured at room temperatures were selected in order to prevent recrystallization during bonding. Bondmaster M-648 (Rubber and Asbestos Corp.) was used for the pure aluminum laminate and Armstrong A-6 (Armstrong Products Co.) was used for the alloys. The alloy for extrusion was cast in a cylindrical graphite mold! cropped and machined into a 3-in. diam by 4-in. long billet. This billet was preheated to 455°C, upset to 3.125 in. diam, and extruded on a 700-ton hydraulic press at a speed of 6 fpm through a flat-face, 1-in. diam die. The rod was quenched with a water spray as it emerged from the die. Pole-distribution data were obtained using the diffractometric method described by Jetter and Borie.7 A spherical X-ray diffraction specimen of

Jan 1, 1961

By L. J. Howell, A. S. Roy, H. H. Kellogg

KNOWLEDGE of the phase diagram of salt systems is important for selection of the optimum con- ditions for electro winning of the refractory metals from fused salts. This note summarizes the studies of the NaC1-rich portion (0 to 22 mol pct HfC14) of the NaC1-HfC14 phase diagram. Melts in this composition range have vapor pressures well below one atmosphere and melting points between 548° and

Jan 1, 1959

By R. J. Sherman, M. R. Achter

Creep rates have been measured for nickel at 1200°F in air and in vacuum, and related to the depth of surface cracks in the specimens tested in the two environments. The surface cracks were observed to grow faster in air than in vacuum in both short-time and long-time tests. Crack depths, however, could be correlated with creep rates only in the short-time tests. Although no cracks were observed in a relatively brittle Ni-Cr-A1 alloy creep tested at 1300°F, the appearance of alloy specimens fractured after interruption in creep indicated that there was a decrease of intergranular cohesion resulting from the diffusion of atmospheric gases into grain boundaries. PREVIOUS investigations1-3 have demonstrated that the effect of atmosphere on the high-temperature strength of nickel and nickel-base alloys may be reversed by changes in the stress or temperature of the test. At high stress and low temperature the creep-rupture life is longer in vacuum than in air, while at high temperature and low stress the relative strengths are reversed. A mechanism to explain this behavior was proposed based on two competing processes. Oxidation hardens and strengthens a metal, but adsorption of gas, by lowering surface energy, reduces the work required to propagate an intergranular crack. The controlling process is determined by temperature and stress. Basic to this mechanism is the concept that environment determines the ease of propagation of intergranular cracks and thus affects creep rate and rupture life. To explore the mechanism in greater detail, this investigation was undertaken to determine the effect of atmosphere on crack initiation and propagation rates in nickel1 and a relatively brittle Ni-Cr-A1 alloy.3 EXPERIMENTAL PROCEDURE The materials were the same as used previously. Nickel of 99.8 pct purity had the following impurity content: 0.02 pct Co, 0.03 pct Fe, 0.02 pct Mg, 0.03 pct Si, and 0.008 pct C. Rods were cold swaged from 1/2 in. to 3/8 in. in diam and machined into speci- mens with gage sections 1/4 in. in diam by 1-1/4 in. long. They were annealed in vacuum at 1600" F for 1 hr to achieve a grain size of 0.07 mm. The alloy was composed of 19.1 pct Cr, 3.6 pct Al, 1.7 pct Si, 0.57 pct Fe, 0.10 pct Mg, 0.027 pct C, 0.004 pct S, and the balance Ni. Sheet specimens of 0.500-in. width and 1.25-in. gage length were machined from 0.033-in.-thick strip and annealed in vacuum at 2000° F for 2 hr, resulting in a grain size of 0.036 mm. Large amounts of an intergranular phase were introduced as a result of the anneal. Creep tests on both materials, using equipment previously described by Shahinian; were conducted in air and in a vacuum of 1 x 10-5 mm Hg. They were continued to rupture and interrupted at various stages of the test. Although extensions were measured from dial gage readings of movement of the lever arm, it is considered that valid comparisons of creep rate may be made in this manner.l Two parameters were measured metallograph-ically* on longitudinal sections of nickel specimens interrupted during creep—the mean depth of surface cracks 2, and the density n as the number of cracks per unit length of surface. They were combined into one parameter by the relation p = n-d [1] As used here, p is equal to the total of crack depths per unit length of surface. RESULTS Nickel. It is well known that the incidence of intergranular cracking is increased with increasing rupture life. Indeed, it is evident in Tables I and I1

Jan 1, 1962

By Carleton Ellis

(Presented at a meeting of the New York Local Section of the Institute, Apr. 12, 1912.) I. INTRODUCTION. THE problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific stand-point, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by way of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " ?flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of combustion as they occur in ordinary flames. All hot surfaces have an accelerating influence upon chemical changes in gaseous systems. If, at any temperature, a gaseous system, A, tends to pass over into another system, B, contact with a solid at the same temperature will accelerate the process. To take a very simple example, if a mixture of hydrogen and oxygen in their combining proportions (electrolytic gas) were maintained in an inclosure with smooth glass walls at a temperature of, say, 450° C., there would certainly be a tendency to form steam, but the rate of change would be negligibly small. If, however, there were brought into the system some porous solid material at the same temperature, so that a large surface was exposed to the gases, the rate of change would at once be rapidly accelerated in the layer of gas immediately in contact with the hot surface. Steam, the product, would diffuse outward from the surface, and the supplies of hydrogen and oxygen at the surface would be renewed by diffusion inward. Thus combustion would proceed heterogene-

Sep 1, 1912

By R. R. French

Investigations were conducted by the lndiana Geological Survey for some dry methods of bene-ficiating low-grade gypsum ore. Seventy-two batch and continuous flow tests were performed with a roller mill, rod mill, pebble mill, electronic color sorter, electrostatic separator, and an air separator. Approximately 650 size analyses and 550 chemical analyses were performed during the investigation. Batch samples were tested by the Survey, and most of the continuous flow tests were handled by com-mercial laboratories. INTRODUCTION Although many companies producing gypsum have been interested in dry beneficiation, very little information has been published in the past. One of the most comprehensive investigations was reported by the Canadian Department of Mines.5 Other reports of interest have been published by the Canadian Department of Mines,' the South Australian Department of Mines,2 and the U.S. Bureau of Mines.3 Some beneficiating practices, such as hand picking, selective mining, crushing and screening, milling, and air classifying, were already in use in the Canadian industry prior to MacPherson's investigations.5 MacPherson examined the effect of tabling, air separation, screening, flotation, electrostatic separation, calcining, washing, and various types of milling, in his efforts to eliminate dolomite, limestone, and small amounts of silica and clay from the gypsum ore. RAW MATERIAL Gypsum and anhydrite occur within the lower part of the St. Louis Limestone (Mississippian) in southwestern Indiana. Gypsum in single beds 10 or more ft thick occur at Shoals, Martin County; near Freedom, Owen County; near Bloomfield, Greene County; and in the Devonian strata of LaPorte County. Only the Shoals deposit has been exploited commercially. The western edge of the Shoals deposit is contaminated by a continuous bed of shale, about 1 1/2 to 2 ft thick, near the top of the evaporite and by thin continuous strata or irregular masses of carbonate rock. The low-grade material used in these investigations was obtained from the waste pile of the National Gypsum Co.'s plant at Shoals. The waste ore averaged about 67.4% gypsum and was contaminated by various amounts of shale, dolomite, and limestone. All the material had been previously crushed and screened to minus 1 1/4 to plus 3/8 in. X-ray analyses of powdered, sedimentated, gly-colated, and heat-treated samples of the shale showed that it was composed of slightly structurally disordered illite, Fe-rich chlorite, and very finegrained disseminated silt. The clays and silt were partly cemented with carbonate material. Light-gray argillaceous limestone and gray or brown porous dolomite made up most of the carbonate rock contamination. Crushing Characteristics: The rate unweathered gypsum, carbonate rock, and shale reduce in size was determined by crushing handpicked samples in a rod mill and screening at minus 100 mesh (.0059 in.). Fig. 1 graphically represents the data. These data indicate that carbonate rock should be relatively easy to separate from gypsum, but that shale should be difficult to separate from gypsum by differential crushing. Controlled Samples: Eight rod mill tests of hand-picked samples of mixed gypsum and shale and mixed gypsum and carbonate rock were made. Sample weight and crushing weight were standardized, but the scalping screen size was varied from 3 to 10 mesh (.265 to .0787 in.) in order to obtain the optimum purity and recovery. The data obtained from the tests (see Table I) illustrate that the relatively hard carbonate rock allows appreciable beneficiation (13.6 to 18%), but the low strength gypsum and shale allows only minimal separation (3.1 to 7.5%).* Semi control led Samples: During the investigation considerable slaking of the shale was noted when the ore was subjected to alternate wetting and drying. As demonstrated in laboratory tests, as much as 76% shale can be removed by two cycles of wetting and drying in a 48-hour period with subsequent screening at .265 in. Five ore samples, stockpiled and weathered, were screened, rod-mill crushed and rescreened at .157 or .187 in. with excellent results (Table 11).

Jan 1, 1967

Organization Place Date 1918 American Chemical Society Cleveland, O. Sept. American Society of Sanitary Engineers Chicago, 111. Sept. National Petroleum Association Atlantic City, N. J. Sept. American Institute of Mining Engineers Colorado Sept. 2-7 National Association of Stationary Engineers.... Cincinnati, O. Sept. 9-13 Association Iron, Steel, Electrical, Engineers Baltimore, Md. Sept. 9-14 British Iron and Steel Institute, Autumn Meeting London, Eng. Sept. 12-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Electrochemical Society Princeton, N.J. Sept 30-Oct. 2

Jan 7, 1918

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By A. H. Daane, J. F. Haefling

The limits of miscibility in some of the uranium rare-earth alloy systems have been determined in the temperature range 1000°to 1250°C. The solubilities of lanthanum and cerium in uranium are greater than those of the remaining rare earths by a factor of more than two. The solubility of uranium is greater in cerium, braseodymium, and neodymium than in the other rare-earth metals studied. The values found in this study are in qualitative agreement with those which might be expected if the solubility rules of Hildebrand and Scott are applicable. AS interest in nuclear reactors intensifies, many new types of fuels are being suggested in attempts to improve the economics of some of the proposed reactor schemes. To remove some of the difficulties inherent in the use of solid-fuel elements and their reprocessing, many types of liquid-metal reactors have been suggested. One of the more attractive features of several of these reactor concepts is that they include a continuous or semicontinuous process for the extraction of fission products and "bred" fissionable materials from the fuel, utilizing immiscible metal extractants. This would enable a much higher burn-up of fissionable material to be achieved and would present a very attractive economic picture. Several studies have been reported on equilibrium systems in which there exists a high degree of immiscibility between uranium and another metal that might be used as an extractant in such a processing scheme.' Two of these systems in which a high degree of immiscibility exists are those of uranium with the two rare-earth metals, lanthanum, and cerium. Since the rare earths constitute a significant fraction of the fission products, their removal is of prime importance. It is reasonable to believe that this might be accomplished by equilibrating a rare-earth phase with the contaminated uranium fuel in the liquid state. In order to make a more complete study of those systems which would be of interest either as extractants in a liquid-liquid extraction process, or as fission products formed in the fuel, the alloy systems of uranium with lanthanum, cerium, praseodymium, neodymium, and samarium were studied in some detail in the temperature range 1000" to 1250°C; less detailed studies were made with the other rare earths. In addition to being of value to the reactor program, the data obtained in this study should be of help in making a study of the role played by the electronic structures of metals in determining the nature of metallic solutions. The unique electronic structures of the rare-earth elements make them particularly interesting in this respect. EXPERIMENTAL The usual procedure for a solubility determination was to seal equal volumes of uranium and the particular rare earth in a tantalum crucible under an atmosphere of helium; this crucible was then sealed in a stainless steel jacket in an atmosphere of helium. These samples were equilibrated by repeated inverting of the crucibles in a furnace for 15 min at the desired temperature, left in an upright position for 15 min to permit separation of the two phases, and then quenched under a stream of water. In some runs the temperature of the furnace was held 50' to 100°C above the desired quenching temperature while inverting in order to insure good mixing. However, it was found that above 1200°C the crucibles were subject to failure and for these runs the furnace temperature was not raised above the desired quenching temperature. A small amount of tantalum was dissolved in the uranium and the rare earths in these runs, a maximum of 3 wt pct in the uranium phase at 1250°C and up to 1 wt pct in the rare-earth phase at this temperature. On cooling, the major portion of this tantalum precipitated as primary tantalum crystals. Any residual tantalum would probably have a negligible effect on the mutual solubility of uranium and the rare earths in each other. Samples for analysis were cut from each phase with an abrasive cutting wheel; the region near the interface between the two metals was carefully avoided. In the case of the rare earths with melting points above 1250°C no solubility data were taken on the rare-earth phase since this phase could not have achieved equilibrium in a reasonable length of time. (For the same reason no data were taken on the uranium phase below its melting point of 1132°C.) Equilibrium appeared to have been reached in the uranium phase in these cases although the rare-earth phase had not melted. To verify this, samples were melted together in an arc furnace similar to that described by Kroll.2 These samples were sub-

Jan 1, 1960

By R. F. Mehl, G. T. Horne

Diffusion coefficients and mobilities were determined as functions of concentration in the a phase of the Cu-Zn system. Use was mode of incremental diffusion couples to determine the Kirkendall effect at various concentrations. Darken's analysis was used to calculate the individual diffusion coefficients and mobilities from these data. The general diffusion coefficient is a single-valued function of the concentration in this system to within the limits of accuracy of the experimental methods used. The form of the various functions (diffusion coefficients and mobilities) of concentration is the same in every case: it is essentially the same as the usual D vs c curve. AS Darken' has pointed out, the knowledge that the movements of different atoms diffusing in the same lattice need not proceed at the same rate is old. Ionic lattices are the classical examples; application of the generalization to lattices with metallic bonding was much more slowly accepted. It remained for Kirkendall'' to show clearly that metallic diffusion need not be symmetrical with respect to both species. Several investigators" have confirmed the initial observation of a "Kirkendall effect:" marker movement accompanying diffusion. They have extended it to other systems and conditions. The theoretical interpretations have been many; ne of the first and simplest of these is that of Darken"' which is essentially mechanism independent. Darken has shown that the Kirkendall experiment permlts a calculation of the individual diffusion coefficients and, coupled with activity data, offers a means of measuring the mobilities of the separateatoms in a binary diffusion process. There is no published information on the effects of concentration and temperature on the individual diffusion coefficients or on the mobility values in binary solid solution; this paper provides such information for zinc and copper in a brass. For purposes of clarity, the overall D value obtained, for example, from the Boltzmann-Matano solution to Fick's law, will be designated as the "general diffusion coefficient;" and the diffusion co- efficients for the separate diffusing species will be designated as the "individual diffusion coefficients." Experimental Procedure The authors have accepted Darken's analysis and have measured mobilities on this basis. The findings of da Silva and Mehl are accepted: that the Matano interface, defined as the origin of coordinates for the Boltzmann-Matano solution to Fick's law, coincides with the original weld interface; that the "shift" of a marker is the distance between the Matano interface and the marker; that the observed porosity is too small sensibly to affect this result; and that the shift is a linear function of the Matano area, the area defined as the absolute magnitude of the area on either side of the Matano interface. Alloys: The a-phase of the Cu-Zn system was chosen for investigation. The measurements were made on incremental couples for two separate reasons: l—it has been questioned whether D, the general diffusion coefficient, is a single-valued function of concentration (a comparison of the D-values for couples with small concentration range, e.g., 10 vs 20 pct Zn, against those from a wide concentration range, e.g., 0 vs 30 pct Zn, will answer that question); and 2—on the Darken analysis, the mobility can be determined only at the concentration at which the marker is observed to lie (this is but one concentration in a single couple) but choosing a series of incremental couples in the range between 0 and 30 pct Zn provides mobility values at several concentrations, thus giving mobility as a function of concentration. Four alloys were chosen; nominally, pure copper, copper with 10 pct Zn, copper with 20 pct Zn, and copper with 30 pct Zn. This allowed six different types of diffusion couples to be prepared, promising mobility determinations at six different concentrations, but having a minimum range of 10 pct Zn. The copper was an especially prepared pure copper supplied through the courtesy of the Ameri-

Jan 1, 1956

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By Lo-Ching Chang, J. Chipman

The perennial and increasing interest in the chemical behavior of steelmaking slags has led to numerous attempts to formulate the thermodynamic properties of these solutions. The classical view is that of a solution of the component oxides in which certain acidic oxides are more or less completely held in combination with basic or metallic oxides, the nature of the interoxide compounds being derivable from the chemical behavior of the slag or from the mineralogy of a solidified specimen. The known electrical conductivity of slags has pointed to the existence of ions in the solution and a number of attempts have been made to account for the observed facts of slag behavior on the basis of a theory of complete ionization of the solution. It is the purpose of this paper to examine, in the light of ionic theory, a number of recently published series of data on slag-metal and slag-gas equilibria, with the purpose of obtaining a more complete or more satisfactory generalization than has been possible on either of the single bases of simple compound formation or complete ionization. The attempt to formulate the ionic constitution of a complex solution is fraught with many uncertainties. An ion is not something that can be plucked from the solution and examined in detail, nor can its true formula be determined with certainty by any single experimental method. In attempting to express the composition of a slag by various ionic formulas it can be expected that alternative hypotheses of essentially equal merit will present themselves. In the present state of early development of the ionic theory of slags, it may be necessary to make some rather arbitrary choices of ionic formulas in the absence of su- cient information to yield complete certainty. Acids and Bases The classification of slag-forming oxides as acidic or basic apparently dates back into the days of Berzelius. It is difficult to see how the concept could have originated in the early twentieth century when it was fashionable to define an acid or a base as an aqueous solution containing hydrogen or hy-droxyl ions. It is, however, entirely consistent with the modern and more general theory of acids and bases. In this theory, as originally formulated by G. N. Lewis,' a basic molecule is one that has an electron pair which may enter the valence shell of another atom thus binding the two together by the electron-pair bond. An acid molecule is one which is capable of receiving such an electron pair into the shell of one of its atoms. The acid, the base, and the product of neutralization may be either ions or neutral molecules. The product of such a reaction may itself be a base or an acid if it is further capable of giving or accepting an electron pair. Thus a base is a donor of electrons, an acid, an acceptor. In oxide slags the typical and ever-present base is oxide ion, 0-—. In behavior and in importance it is analogous to hydroxyl ion, OH-, which is the typical base of aqueous solutions. There is nothing in the chemistry of slags which is quite analogous to the acid H30+ in aqueous solutions. This is not surprising for in slag systems there is nothing which can be designated as a solvent and no ubiquitous positive ion. The chemistry of slags is in fact more complex than the chemistry of aqueous solutions and the concepts which must be evoked in its study are correspondingly broader. In seeking a basis for a classification of slag-forming oxides as basic or acidic it must be remembered that these terms are not absolute but relative. A substance which acts as a base toward a second substance may act as an acid toward a third. This is less likely to happen among strong bases or acids than among the weak ones; there are numerous examples of weak acids which under the influence of a stronger acid behave as weak bases. Such substances are called amphoteric. A classification of the glass-forming oxides has been proposed by Sun and Silverman² and further developed by Sun3 in which the oxides are arranged in order of decreasing acidity or increasing basicity, each substance being potentially capable of acting as an acid toward substances below it in the list and as a base toward those above it. It is based upon the relative strengths of the metal-to-oxygen bond as determined by the energy required to dissociate the oxide into its component atoms.' Data are available for computation of this energy, at least approximately, for the oxides of slags and glasses. In general those oxides from which it is most difficult to remove the positive atom are the strong acids while those in which it is most loosely held are the strong bases. It is in the latter, of course, that formation of oxide ion occurs most readily as, for example, in CaO which in solution ionizes to form the weak acid Ca++ and the strong base O—. The order of arrangement found by Sun is shown in the first column of Table 1, to which have been added the data for

Jan 1, 1950

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By C. S. Smith, E. W. Palmer

IN 1934, when Gregg and Daniloffl wrote their excellent monograph on the alloys of iron and copper, the most recent literature on the constitution of the alloys indicated a narrow single-liquid area for 20" above the liquidus with a closed liquid mis-cibility gap above this. Since that time, however, a number of investigators have confirmed the much earlier studies of Mushet2 and Stead3 who, among others in the nineteenth century, had described the true state of affairs. Liquid copper and iron are completely miscible in the absence of carbon, but small amounts of carbon cause liquid segregation. In 1934, one of the writers' mentioned evidence for the absence of liquid separation in carbon-free alloys at temperatures up to 1700°C. Two years later, Mad-docks and Claussen5 unequivocally established the absence of liquid segregation and published a revised diagram, reproduced in fig. 1. They also studied the limits of the two-liquid area in ternary alloys of iron, copper, and carbon as a function of carbon and iron content. In the same year Simpson and Bannister" and Schumacher and Souden7 described in some detail the properties of alloys containing 50 to 75 pct Cu. More recently Hodges et al.16 have developed the copper-rich alloys for use as high-strength conductors. In 1937, Iwase, Okamoto, and Ameniya8 published data on the miscibility gap in ternary alloys of iron, copper, and carbon that supported the conclusions of Maddocks and Claussen, and definitely located the two-liquid area at temperatures of 1450" and 1540°C. They also reported that additions of 1 pct Al, Ni, Pb, Sn, or Zn caused no segregation in 50 pct Cu alloys at 1540°C. The use of copper in amounts approximating 1 pct has found industrial employment to an increasing degree in both wrought and cast steels, for such steels are capable of being precipitation-hardened following normalizing, and have high yield strengths. This is summarized by Gregg and Daniloff,1 Sallitt,9 and Lorig and Adams,10 while Alexander" gives additional information on the heat treatment of copper-steel castings. Lippert12 has described Digby's two-phase steels containing copper and chromium. The work described in the present paper was done in the years 1932 to 1934, at which time much of the information was new. The excellent work subsequently done in other laboratories but more promptly published makes the present paper in part only a confirmation of what is now well known. There has not, however, been published any unified study of

Jan 1, 1951

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By Torgrim Eftestoel, Leif Olsen, Ove Sandberg

IN the vertical contact Soederberg electrode for aluminum furnaces more or less serious cracks are sometimes formed in the electrode, with harmful effect on furnace operation. The problem of crack formation has been studied on a laboratory scale to obtain a better understanding of this phenomenon. The primary cause of crack formation is the shrinkage of the electrode carbon, which is opposed by the normal thermal expansion of the steel contact studs. The forces thus set up are active in the temperature interval from which the electrode obtains a rigid structure (450" to 500°C) to furnace operational temperature (950°C). A visualization of our reasoning is given in Fig. 1, which shows the different behavior of mild steel and electrode carbon during baking. Research work performed to determine relationships between crack formation and shrinkage will be described. A brief description of the method developed for measurement of shrinkage will be given, as well as a critical analysis of this method. Also, raw material quality and paste composition variables will be related to shrinkage phenomena. Laboratory Test of Crack. Formation To test the tendency toward crack formations of Soederberg electrodes from different pastes, experiments were performed to simulate conditions of actual commercial electrodes, and are described as follows. A cylindrical test electrode is prepared by tamping the electrode paste to be examined in a sheet iron casing, 350 mm diam by 700 mm height. The casing is perforated, with the holes (2 mm diam) 50 mm apart, to facilitate the escape of volatile matter during baking. A cylindrical steel stud of actual service size, 100 mm diam, is welded eccentrically to the bottom steel plate, and protrudes up through the paste. During baking, a crack may thus occur in the weaker part of the test electrode. The electrode is baked by lowering the assembly slowly into an electric furnace, the temperature of which is kept constant at 900°C. After baking of the electrode, the sheet iron casing is removed and the electrode inspected for cracks. The pictures in Fig. 2 are of three different pastes baked according to the present method. Electrode 1 has a large crack; electrode 2, a somewhat smaller one; and electrode 3, only a minor crack. As will be seen from the simplified sieve analysis diagram of Fig. 2, the compositions of the pastes in question are very different. This subject will be discussed later in greater detail. Crack Formation and Shrinkage Relationships It is well known that shrinkage occurs in coke in the higher temperature ranges of coal

Jan 1, 1958

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937