Search Documents

By H. Conrad, K. Janowski, G. Stone

The available data on the dynamics of plastic flow of sapphire indicate that the deformation rate in the temperature range .from 900° to 1700°C can be expressed either as A number of investigators1-10 have established that sapphire deforms plastically above 900°C, the most common mode of deformation being slip on the basal plane in the [1120] direction. Under certain conditions and at temperatures above 1500°C, slip

Jan 1, 1965

By A. N. Rogers

Jan 1, 1883

By AIME AIME

ON the morning of Monday, Nov. 9, 1936, two motorcycles, with sirens screeching, - escorted a procession of 70 automobiles from the Colonia Railway Station in Mexico City to the Hotel Geneve. Riding in' the cars were just over 200 visitors- members of the A.I.M.E. and their guests. They had come, via St. Louis, in two special trains from 24 different states for the 146th General Meeting of the Institute. During the morning they and 200 others, who had come from the United States by automobile or from various cities and mining camps in Mexico, duly registered with !efficient Mme. Irma Ordoiiez de Obregon and her assistants. Then started a week of strenuous but delightful activity that will never be forgotten by the participants. They were to cover more than 500 miles by automobile, always with a motor escort, and often

Jan 1, 1937

By S. W. Parr

FRom a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows: Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric acid— 1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60" C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present. Sulfur in the form of iron pyrites, or marcasite, may be quantitatively removed without oxidation of the organic sulfur as follows: A dilute solution of nitric: acid is prepared having 1 part of concentrated HNO3 to 3 parts of water or with an approximate specific gravity of 1.12. The coal sample, ground to 100 mesh, is digested with this solution at room temperature for 3 or 4 days, filtered and evaporated to dryness, taken up with water, and acidified with hydrochloric acid. It is now ready for precipitation with barium chloride in the usual manner. If sulfate is present in the original sample to an appreciable amount, it should be removed by the procedure outlined above. It is not necessary here to give the methods for determining the two

Jan 1, 1920

By Albert A. Mathews

OUTCROPS of gypsum rock near the present site of the city of Gland Rapids, Mich., were known to fur traders early in the nineteenth century. However, the deposits seemed without value and were not worked for some time. So far as cat1 be learned, Michigan gyp- sum was first used by a plasterer who settled in Grand Rapids in 1834 as a member of its fourteenth white family. In building a house for one of the early traders, be used some otnamental stucco mouldings manufactured from the local gypsum deposits for decorations in the gables and around some circular windows. The gypsum was broken out with a hammer, ground in an Indian corn mill, and burlled in a caulclron kettle,. After two attempts, the ornaments were successfully set, and remained on the house until it was destroyed by fire in 1850.

Jan 1, 1936

By K. D. Jacob

IN the decreasing order of the tonnages involved, the uses of phosphates can be grouped conveniently into three general classes, namely, fertilizer; chemicals for military, industrial, and technical purposes; and mineral feed for livestock. The quantity of phosphate used as fertilizer, principally in the form of superphosphate, has always exceeded by far that used for all other purposes, though in recent years a marked increase has occurred in its consumption for the other two general classes of uses. Prior to the present century large quantities of superphosphate, as well as a considerable portion of the production of phosphorus chemicals, score made from bone materials which were plentiful and cheap in some areas and which could be more easily processed than phosphate rock for the manufacture of chemicals. Today, however phosphate rock has almost completely displaced bone as a raw material for the manufacture of chemically processed phosphates in nearly all countries of the world.

Jan 1, 1944

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By W. O. Philbrook, K. Natesan

A mathematical model was derived for the temperature change in a particle undergoing heterogeneous chemical reaction and heal exchange with a stream of fluid. The model has been applied specifically to the exothermic oxidation of spherical particles of zinc sulfide. Very good agreement was obtained between the theoretical prediclion and experimental observation. It was found that at no stage of the reaction was the particle subjected to a state of thermal instability. In studies of gas-solid reactions, it is generally assumed that the gaseous and the solid phases are at the same temperature throughout the reaction period. This is not strictly true since most of the reactions are either exothermic or endothermic in nature. This paper deals only with heterogeneous gas-solid reactions of noncatalytic type. In the case of exothermic reactions (e.g., roasting of sulfides), there may result an increase in temperature of the particle due to the release of the heat of reaction, and this increase in temperature may enhance the reaction rate and thus cause further release of heat. Such a "spiralling" effect may lead to a thermally unstable situation within the particle. On the other hand, in the case of endothermic reactions (e.g., calcination of limestone), there may occur a decrease in temperature of the particle as the reaction proceeds, leading to a virtual "quenching" of the reaction front. A general discussion of autothermic processes with emphasis on properties and reactor design is given by Van Heerden. 1 Levesque and cubicciotti 2 observed self heating of the sample in the oxidation of thorium. Anous et al. 3 observed self cooling of the sample in their dehydration studies on chrome alum. Cannon and Denbigh, 4 and Ong et al.5 reported self heating of the sample in their studies of the kinetics of oxidation of zinc sulfide. A typical plot of heat generation and heat loss rates with reaction temperature is shown in Fig. 1.'14 The Sigmoid curve represents the heat generation rate while the straight lines represent the heat loss rate. The main objectives of this analysis are to estimate the temperature increase of a single particle undergoing an exothermic reaction and to study the possibility of a thermally unstable situation within the particle. Also, a study of the dependence of the tempera- ture increase on different process variables has been attempted. A "she ll-by-shell" method has been proposed to analyze the problem. The shells may be made as small as necessary, and equations may be set up for heat transfer by various mechanisms. Such equations will have to be solved for each shell, with the boundary conditions for ith shell being obtained from the (i - 1)th shell, using a high speed digital computer. The oxidation of spherical particles of zinc sulfide is considered for this analysis, but the treatment is general enough to be applicable to other reactions and particle shapes. The oxidation reaction can be written as AH =« -115 kcal/mole ZnS [1] Such a reaction has been found to proceed in a topo-chemical manner; i.e., as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,4-6 that the particle retains its original dimensions. Therefore, at any given time, the particle may be

Jan 1, 1970

By R. M. Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped East for reduction. Practically no chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in lowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. Table 1.—Electric Smelting Plants in Colorado Capacity. Company Location KilowattB PRoductS Tungsten Products Co........... Boulder 800 Ferrotungsten, ferromo- lybdenum. Boulder Tungsten Production Co .. Boulder 400 Ferrotungsten. Ferro Alloy Co.................. Utah Junction 1200 Ferrochrome, ferrotung- sten. Iron Mountain Alloy Co......... Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co. The plant of the Ferro Alloy Co., at Utah Junction, contains one 750-kw., three-phase furnace, to which power is supplied by three 250-lrw. transformers, connected /Y to give 129 volts on the furnace cables, the transformer ratio being 13,200 to 75 volts. The furnace operates with an actual voltage of 120 volts, and produces about 3 tons of ferrochrome per 24 hr. from 40-per cent. Cr2O3 ore. The furnace consists of a steel shell of circular cross-section, 8 ft. (2.43 m.) in diameter by 7 ft. (2.13 m.) deep, lined with magnesite, and having three vertical carbon electrodes 12 in. (30.48 cm.) in diameter. A 450-kw. furnace, of the same size as the 750-kw. furnace, is also operated on chrome ore. This furnace is three-phase in appearance, but operates electrically as a single-phase furnace. There are three vertical

Jan 1, 1920

By Michael B. Bever, Barton Roessler

The effects of deformation by wire drawing at 78OK on initially ordered and initially disordered specimens of the alloy Cu3Au were investigated. The resistivity, stored energy, drawing force, and microhardness were measured as functions of strain; microstructural changes were observed. The results are interpreted in terms of the structural imperfections and the changes in atomic configuration resulting from deformation. A few experiments on the effects of room-temperature annealing after deformation at 78°K were made; they suggest vacancy-promoted ordering in disordered alloys. BARTON ROESSLER, Junior Member AIME, formerly Graduate Student and Alcoa Fellow, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass., is with Westinghouse Research Laboratories, Pittsburgh, Penn. MICHAEL B. BEVER, Member AIME, is Professor of Metallurgy, Massachusetts Institute of Technology. Based in part on o thesis by B. ROESSLER submitted in October, 1959 to the Massachusetts Institute of Technology in partial fulfillment of the requirements for the degree of Doctor of Science. Manuscript submitted April 6, 1961. IMD AN investigation of the effects of deformation at room temperature on the alloy Cu3 Au was reported in a recent paper,' which included a review of the literature on the deformation of order-disorder alloys. In general, plastic deformation of ordered alloys reduces the degree of long-range order and causes corresponding changes in their properties. Deformation of disordered alloys changes their properties in a manner characteristic of solid solution alloys; these changes can in part be attributed to the destruction of short-range order. The effects of deformation on solid solution alloys are of two kinds: 1) generation of structural imperfections, which occurs as a result of deformation in any metallic system including pure metals, and 2) changes of atomic configuration, which are characteristic of solid solutions and particularly of order -disorder systems. These two types of effect are not independent of each other and the state of a deformed solid solution alloy is determined in a complex manner by the way in which the structural imperfections cause changes in atomic configuration both during and after deformation.

Jan 1, 1962

By J. B. Mackintosh

THE present note is intended as an addition to my previous communication on the volumetric determination of manganese, read at the Roanoke meeting," it having been suggested that the circumstances under which my experiments had been conducted, were essentially different from those met with in the analysis of irons. The method used in these experiments is the same in all its details as that described in the paper referred to. I have made seven experiments in all: two of these were in duplicate on half a gramme of a sample of spiegel dissolved in hydrochloric acid; one was on the same amount of spiegel with the addition of 25 C.C. of a standard solution of potassium permanganate; one was on the same amount of spiegel with the addition of 35 C.C. permanganate and much organic matter, viz., one drop of castor-oil, two or three drops of coal-tar benzol arid of gasolene (petroleum), about ten of alcohol, portions of starch and of sugar about the size of a small pea, and about half an inch of a common match cut into shavings. This organic matter was added to the manganese solution after the hydrochloric acid had been replaced by nitric, and the solution was heated until the wood-shavings had disappeared. The fifth experiment was made by dissolving half a gramme of spiegel alone in nitric acid; the sixth by dissolving half a gramme of spiegel in nitric acid with the addition of 25 C.C. potassium permanganate, some oxalic acid, half an inch of a match, one filter-paper 7 cm. in diameter, and two drops each of castor-oil and turpentine; and the seventh experiment by dissolving half a gramme of spiegel in hydrochloric acid and adding 35 C.C. permanganate, without however taking the precaution to evaporate off all the excess of hydrochloric acid. Under these circumstances, one would expect that if organic matter exercises any influence on the determination, it would be plainly evident in the results obtained. But the accompanying table of results

Jan 1, 1885

By G. F. Comstock

A serious disagreement as to the effect of titanium on the hardenability of steel exists in published references to this subject. Kramer, Hafner and Toleman reported' that acid-soluble titanium decreased creased the hardenability, with multiplying factors less than unity according to [ ] Grossmann's system for calculating hardenability from the composition. Crafts and Lamont, on the other hand, showed2 how titanium increased the hardenability, with multiplying factors up to nearly 1.7 for about o.' per cent titanium, though reducing the hardenability with higher titanium. Their data, however, were obtained almost exclusively from steels containing more than 2.4 per cent manganese, and thus should be considered as applying mainly to manganese steels. Likewise, the results of Kramer, Hafner and, Toleman regarding titanium are subject to the limitation that although they eliminated the effect of the insoluble titanium compounds from their calculations, they did not make a similar correction for the carbon that was combined with titanium and therefore occurred in a similarly ineffective form. It is suggested by the literature referred to that titanium may have different effects on hardenability, depending on the mode of its occurrence in the steel. The different effects on strength, ductility, etc., have already been discussed by the author.3 In the present discussion some comparisons, on the basis of hardenability as revealed by the Jominy end-quench test, are given between three titanium and two non titanium steels heat-treated in the same ways, and between other titanium steels heat-treated in several different ways. COMPARISON OF PLAIN-CARBON, VANADIUM AND TITANIUM STEELS The five steels used for these experiments were commercially melted and rolled products received in the form of 1.5-in. rounds from three different mills. Their analyses are given in Table I. Steels 2, 3, and 4 are from the same basic electric heat, containing 0.009 per cent of phosphorus and the same amount of sulphur. They were made by, adding aluminum and low-carbon ferrotitanium to different ingots. No. I is a plain-carbon coarse-grained S.A.E. 1040 steel made by the basic open-hearth -process. No. 5

Jan 1, 1945

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By Eugene H. Dawson

MICA is a mineral that once was a familiar sight as fireproof windows in stove and furnace doors and as lamp chimneys and shades. Since 1878, the beginning of the electrical age, the use of mica for such purposes has gradually declined and its use in electrical equipment and appliances has developed to such an extent that the known sources of supply are scarcely equal to the demand. With the increasing capacity of electric generating units, the size of mica sheets found in nature was inadequate. However, in 1894, a process was developed whereby thin films or splittings cemented with shellac or other binders could be pressed into large sheets. 18 The introduction of radio in the early 1920s created such a heavy demand for the smaller sizes of mica that on March 22, 1938, mica was included among 23 commodities on the list of strategic materials approved by the United States Army and Navy Munitions Board. To be included in this list, the material must be one whereof the domestic supply is not sufficient to meet the demand. COMPOSITION Mica is a complex mineral composed principally of the silicates of potassium, aluminum, and magnesium. Less prevalent species contain, as essential components, lithium, vanadium, and chromium. Iron usually is present either as an essential component or as an impurity. The mica group comprises some nine different species, five of which, muscovite, phlogopite, vermiculite, lepidolite, and biotite, are widely used in industry. Lepidolite and zinnwaldite (lithium micas) and roscoelite (vanadium mica) are sources of lithium and vanadium. Muscovite, "white mica," is potassium mica. Theoretical formulas H2KAl3(SiO4)3. There are two varieties, distinguished as to color, known in industry as ruby and green. In crystals or "books," the colors each range through varying shades of red and green. However, when split into thin films, all micas, except biotite and phlogopite, are colorless and transparent. Muscovite frequently is stained red or black by thin films of iron oxide between the laminae. The staining usually is derived from magnetite, which sometimes is found as unaltered crystals.

Jan 1, 1949

By C. E. Wood

THE Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, has been working for several years on the mechanism of desulphurization of iron and steel by slags. The usual assumption that desulphurization takes place by diffusion of FeS from metal into slag and subsequent reaction of this FeS with CaO to produce CaS has seemed to us inconsistent with a number of experimental results we have obtained. We undertook, for example, to determine the proportion of sulphur in a slag present as FeS. An entirely satisfactory method of doing this has not yet been evolved. The results of extraction with metallic antimony led to an interesting conclusion, however. FeS is readily soluble in metallic antimony, either physically or by chemical reaction. On the other hand, CaS was found to be insoluble. Hence it would appear that by rapid extraction of the slag with antimony we might expect to determine the distribution of sulphur between iron and calcium. The results showed that much of the sulphur was present as FeS. In some instances the extraction of sulphur as FeS was almost quantitative. For example, in a slag containing 3.8 grams Fe and 3.7 grams S, extraction removed 1.18 grams S and 2.12 grams Fe. If all the iron present in the antimony had been FeS, 1.21 grams S would have been extracted. In another slag with 8.6 grams Fe and 0.06 gram S present, 0.14 gram Fe and 0.08 gram S were extracted. This was obviously extraction of sulphur as FeS within the analytical error and showed that FeS was present either in solution or as a dispersion. Attempts to determine the solubility of FeS and CaS in slag by quenching and ultramicroscopic investigation have indicated that the solubility of FeS is very low, and that reactions in the slag are probably not to be considered as homogeneous. A more detailed report on these theoretical considerations will be made at a later date.

Jan 1, 1939

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By AIME AIME

NOT a few physical metallurgists started their profession- al careers as chemists or physicists, only to surrender later to the attractions of metallurgy. The present Institute of Metals Chairman varied this more usual sequence in hat his first love was electrical engineering, when as a recent graduate he served on the staff of the General Electric Co., of Schenectady. Soon turning to metallurgy as a more interesting field, he was metallurgist and then chief engineer of the Wads- worth Watch Case Co. from 1920 to 1927. Since 1927 he has been with the International Nickel Co. at the Bayonne, N. J., research laboratories where he is staff adviser.

Jan 1, 1940

By JOHN D. SUMMER

THE Premium Price Plan for copper, lead, and represent, the approach of the Office of Price Administration to the urgent of wartime problem of securing increased output of nonferrous metals. Some of the problems encountered in too operation of the Plan and the considerations which led to it?s adopt it will here he reviewed. The Plan provides for extra payment by the Metals Reserve Co., to mine operators who exceed established quotas of production. Producers are thus directly, compensated for the higher costs of working ores that are not commercial at the ceiling price, although the metal obtained from these ores is directed into regular channels of distribution at the established prices for copper, lead, and zinc. Higher-cost metal is thus available to fabricators and to the government agencies at the regular ceiling price and the dual objective of increased production and table pries is achieved.

Jan 1, 1943

By Nicholas J. Grant, John S. Benjamin

A series of composite alloys containing a high volume of NiAl, Ni3Ah or CoAl, bonded with 0 to 40 vol pct of a ductile metal phase, were prepared by powder blending and hot extrusion. The binder metals were of four types: pure nickel or cobalt, near saturated solid solutions of aluminum in nickel and cobalt, type 316 stainless steel, and niobium. Sound extrusions were obtained in almost all instances. Studied or measured were the following: interaction between the alunzinides and the binders, room-temperature modulus of rupture values, 1500° and 1800°F stress rupture properties, hardness, structure, and oxidation resistance. Stable structures can be produced for 1800°F exposure, with interesting high-temperature strength and good high-temperature ductility. Oxidation resistance was excellent. A large number of experimental investigations have been made of the role of structure on the properties of cermets and composite materials. Gurland,1 Kreimer et al.,2 and Gurland and Bardzil3 have indicated the preferred particle size in carbide base cermets to be about 1 µ, with a hard phase content of 60 to 80 vol pct. The optimum ductile binder thickness was noted to be 0.3 to 0.6 µ.1 Complete separation of the hard phase particles by the binder is important in reducing the severity of brittle fracture.' The purpose of the present study was to produce structures comparable to the conventional cermets, using a series of relatively close-packed intermetal-lic compounds rather than carbides as the refractory hard phase, and to study the effects of binder content and composition on both high- and low-temperature properties. The selected intermetallic compounds were particularly of interest because of the potential they offered in yielding room-temperature ductility. The highly symmetrical structures are known to possess high-temperature ductility and room-temperature toughness. Based on a ductile binder, the alloys were prepared by the powder-metallurgy route to avoid melting and subsequent alloying of the matrix, and were extruded at relatively low temperatures. It was expected that the composite alloy would retain useful ductility. In contrast, infiltration and high-temperature sintering led to alloying of the matrix and to decreased ductility. The systems Ni-A1 and Co-A1 were selected for this study. In the Ni-A1 system the compounds NiA1, having an ordered bcc B2 structure, and Ni3Al(?1), having an ordered fcc L12 structure, were chosen. In the system Co-A1 the intermetallic compound CoAl with an ordered bcc B2 structure was used. ALLOY PREPARATION The intermetallic compounds, see Table I, were prepared by using master alloys of Ni-A1 and CO-A1, with additions of either cobalt or nickel to achieve the desired compositions. The master alloy in crushed, homogenized form, was melted with pure nickel or cobalt in an inert atmosphere, cold copper crucible, nonconsumable tungsten arc furnace. The resultant intermetallic compounds were homogenized at 2192°C in argon, crushed, and dry ball-milled in a stainless mill to -100 and -325 mesh for the Ni-A1 compounds and to -325 mesh for the CoAl compound. Finer fractions were separated for some of the composite alloys. Several ductile binders were utilized. These included Inco B nickel, 5µ ; pure cobalt, 5 µ, from Sher-ritt Gordon Mines, Ltd.; fine (-325 mesh) niobium hydride powder; fine (15 µ) type 316 stainless-steel powder; and near-saturated Ni-A1 and Co-A1 solid-solution alloys, also in fine powder form. The niobium hydride was decomposed above about 700°C in processing of the compacts in vacuum to produce niobium powder. The Ni-7.1 pct A1 and the Co-5.3 pct A1 solid-solution alloys were prepared from pure nickel or cobalt and pure aluminum by nonconsumable tungsten arc melting under an inert atmosphere. The ingots were homogenized, lathe-turned to fine chips, and dry ball-milled in air to -325 mesh powder. These solid-solution alloys are designated NiSS and CoSS; see Table I. Subsequently the hard and ductile phases were dry ball-milled as a blend. Experiments clearly established the need to coat the hard particles with the ductile binder to optimize subsequent hot compaction by extrusion. Ordinary dry mixing usually resulted in nonhomogeneous alloys which were quite brittle. Conventional cermets are consolidated by liquid phase sinteiing or infiltration, which resulis in undesirable and uncontrolled alloying of the binder phase. For this study, a loose (unsintered) powder-extrusion process was emploved, minimizing reactions between binder and hard particle, thereby permitting much greater control of composition and structure. The constituent powders were first mixed in the desired

Jan 1, 1967