Search Documents

By Benjamin C. Craft

Oil and gas development in Louisiana during 1935 brought this state at the close of the year up to fourth place in the nation as a producing area. A review of development in North Louisiana centers around Rodessa, the most important reserve discovered in this area in many years. While the producing limits have not been defined, this discovery is one of the major developments of the year. New gas fields were discovered in Lincoln, De Soto and Bossier parishes. The Lincoln Parish discovery, completed flowing a highly saturated gas from the Glen Rose, further indicates the importance of deep-seated prospects in the interior salt-dome area. Minor extensions were made at Sligo and Pine Island. During the year, 126 oil wells and 103 gas wells were completed in North Louisiana as compared with 144 oil wells and 68 gas wells during 1934. The North Louisiana oil production was 9,617,405 bbl. as com-pared with 9,274,050 bbl. during 1934, an increase of 343,355 bbl., while the gas production increased 18 billion cu. ft. in 1935 over its 1934 figure. The Louisiana Department of Conservation gage of Nov. 1, 1935, shows an open-flow capacity of 4,563,725,000 cu. ft. per day from 941 wells in the Monroe field and 682,770,000 cu. ft. from 159 wells in the Rich-land field. A great deal of leasing continues in North Louisiana as a result of the Lincoln Parish discovery and development in the Rodessa field, especially in Bossier, De Soto, Winn, Lincoln, Bienville, Webster, Ouachita and Richland parishes. South Louisiana's position as an area of important reserves was further proved during the past year. Increased drilling resulted in the discovery of seven new fields: Lafitte, Garden Island Bay, Tepetate, Bunkie, St. Martinsville, Jeanerette and Big Lake. New sands or producing horizons proved productive in 15 of the proven fields. The total oil production for South Louisiana during 1935 was 40,731,-056 bbl. as compared with 23,255,437 bbl. during 1934. There were 222 oil and gas wells completed in South Louisiana during 1935 as compared with 214 oil wells during the previous period. Drilling during

Jan 1, 1936

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948

By R. H. Sweetser

THERE are SO many conditions affecting blast-furnace results that it is hard to get satisfactory comparative data on the working of two furnaces, and much more difficult to get comparable results from the use of two entirely different fuels. The several advantages of charcoal over coke as a blast-furnace fuel have doubtless been apparent to many managers; but probably the conditions for comparative tests of the two were never so favorable as during the year 1905, at the works of the Algoma Steel Co., Sault Ste. Marie, Ontario, which comprise two modern blast-furnaces, well equipped, though of comparatively small capacity. For four consecutive months one of these furnaces was run with charcoal and the other with coke. Then the charcoal-furnace ran for a while with part charcoal and part coke; and, still later, with coke only. The ore-mixtures were about the same in the two furnaces, and, of course, all the climatic conditions were identical. The dimensions of the two furnaces, and their work with the different fuels, are given in Table I.

Jan 5, 1908

By F. W. Newhall, L. N. Plein

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By L. N. Plein, F. W. Newhall

During the latter part of the year 1931, the Republic mine of the Republic Steel Corporation, at Republic, about 4 miles south of Brownsville, Pa., was mining coal along four rib or fracture lines. One of these lines, the west butt rib line, was retreating towards a concrete-lined air shaft, 320 ft. deep, which had been sunk in 1911 for ventilation purposes. With the normal rate of mining at that time, it was expected that this rib line would pass the shaft in three or four months and the shaft would then be abandoned and allowed to cave. Realizing the opportunity presented for the study of an unusual case of ground movement, the question of conducting the study was presented by the junior author to thechairman of the Institute's committee on Ground Movement and Subsidence, Mr. George S. Rice, who presented the matter to Mr. G. H. Morse, General Manager of the Northern Mines, Republic Steel Corporation, and he agreed to cooperate with the Bureau of Mines in making the study, the results of which arc presented in this paper. Acknowledgments are due to Mr. Morse for his full cooperation in this work and to Mr. G. S. Rice and Mr. J. W. Paul, both of the U. S. Bureau of Mines, for their advice and guidance during the course of the work. The authors are indebted to Mr. B. F. Herbert, mining engineer, Northern Coal Mines, Republic Steel Corporation, who assisted in all the surveys, and Mr. W. H. Smith, draftsman, U. S. Bureau of Mines, who prepared all illustrations for publication. Geologic Conditions The shaft is at Merrittstown, which is about one mile northwest of Republic. The topography in the immediate vicinity of Merrittstown consists of rolling country dissected by the meanders of Dunlap Creek and its tributaries. The surface slopes of the hills are gentle and their average gradient is less than 6º. The area at the point where the study was made lies on a hillside sloping towards the southwest, the gradient, varying from 1º to 14º. Fig. 1 shows contour lines at 5-ft. intervals on

Jan 1, 1936

By E. R. Kaiser

COAL research during 1941 had a marked increase in activity on problems bearing directly on furthering the increased and improved use of coal in homes and industry. Coal producers and fuel engineers expressed a greater interest in its practical possibilities and the coal laboratories have shown an increased interest in applied research, of value at once or in the near future to industry and the public. A large volume of accomplishment in mining, coal analysis, and the fundamentals of coal constitution and coal chemistry also continued to fill the storehouse from which applied research and fuel engineering of the future can draw valuable data.

Jan 1, 1942

By R. S. McClellan

DURING the last year or so, with higher prices for gold and silver, many old properties in the West have come back to life. Almost every profitable producer in the old days has been considered, and the reasons for its shut-down investigated. If it seems likely that modern ore-finding, mining, and metallurgical methods, and S35 gold can again put the property on a profitable basis, someone can usually be found to back the venture. Methods of rejuvenation vary with the property, of course, but the following outline of what has been done with one group of mines in Idaho is fairly typical and may be suggestive to others. The Golden Chariot gold-silver properties, near Silver City, consist of seven old mines, working a vein system striking north and south, which had a productive length of some 3500 ft. The vein is a quartz-filled fissure with granite walls. Gold occurs in native, and with silver in the form of electrum which is the natural alloy of the two metals. Silver also occurs in a variety of sulfides. From 1064 to 1876, these old properties were worked intensively to an average depth of about 700 ft., through seven shafts which range in

Jan 1, 1934

FOLLOWING the presentation of the papers by Messrs. Mahan and Butler, the discussion printed below ensued. A. C. LANE* With particular reference to the New England con-sumer, I entirely agree with Mr. Mahan that intelli-gent marketing methods will do a good deal, but there is more than one way of improving them. For instance, coal can be shipped best to New England about this time of year-after the storms of the winter and before the movement of crops in the summer. For that reason there ought to be seasonal freight rates. This will be agreed to by most coal men if you will ask them, especially those who are connected with large concerns like the Metropolitan Coal Co., and yet they do not get seasonal freight rates partly because the railroads are afraid if they once reduce them they will never have a chance to get them back again. But it would be an improvement to have seasonal freight rates. Another thing: When we are buying in New England we want really a certain amount of heat value in our coal. There is no great advantage in our buying ash, nor is there any particular advantage in the railroad shipping ash and clogging the circulatory system of the body politic any more than clogging the circulatory system of the physical body. It would be desirable if the wholesaler, and to some extent the retailer, could guarantee the amount of ash or sell their coal on heating value. If you are interested in that you will find some interesting charts, in "Anthracite Coal Costs Analyzed," a pamphlet issued by the Anthracite Coal Consumers Association, Inc., New York City, as to rates from various and sundry points for bituminous and anthra-cite coal from the field to New York, Buffalo and Chi-cago. Here in New England they are both up against the competition of oil. About 3 or 3 1/2 bbl. oil will do the work of a ton of coal. One of my millionaire friends who is well posted on the situation is putting oil in his Commonwealth Avenue house because it is the most economical. Moreover, we can get Welsh coal from across the water (and help equalize this matter of exchange with Europe) in close competition with Penn-sylvania coal.

Jan 4, 1928

CONTENTS PAGE DANIELS, SAMUEL, LYON, A. J., and JOHNSON,. J. B.-Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys 1 ELLIS, O. W. and SCHEMNITZ, D. A.-Experiments on the Heat Treatment of Alpha-beta Brass : 4 ENOS, GEORGE M. and ANDERSON, ROBERT J.-Coatings. Formed on Corroded Metals and Alloys 5 COMSTOCK, GEORGE F.-Notes on the Hardness of Heat-treated Aluminum Bronze 6 Casting and Heat Treatment of Some Aluminum Copper-magnesium Alloys Discussion of the paper of SAMUEL DANIELS, A. J. LYON, and J. B. JOHNSON, presented at the Milwaukee Meeting, October, 1924, and issued, as Paper No. 1350-N, with MINING AND METALLURGY, July, 1924. D. HANSON and M. L. V. GAYLER, Teddington, England (written discussion).-At the National Physical Laboratory, the writers have made a number of researches on the relation between the constitution and mechanical properties of aluminum alloys of various types; the results obtained were in good general agreement with those of the authors. The writers, however, did not think that increasing the copper content of sand-cast low-copper duralumin to 4 per cent. necessarily caused a drop in the elongation to 1.5 per cent., as stated on page 9. In the case of sand-cast copper-aluminium alloys they had obtained much greater elongation, in some cases as great as 13 per cent. in heat-treated castings. For example, in a sand casting containing 3.5 per cent. of copper, a strength of 12 tons per square inch and an elongation of 13 per cent. were obtained; in a casting containing 4.5 per cent. copper, a tensile strength of 13 tons, and an elongation of 9 per cent. were obtained. These values were the maximum; the elongation varied considerably, being as low as 5 per cent. in some cases. In the writers' opinion, such variations are due more to unsoundness in the sand casting than to any other cause.

Jan 1, 1925

By O&apos, R. G. Meara, B. W. Gandrud

In 1034 the Southern Experiment Station of the U.S. Bureau of Mines in cooperation with the University of Alabama began an investigation of the availability of kyanite ores as a source of raw material for the manufacture of refractories. Under this program, gravity concentration and flotation tests have been made on two varieties of Georgia kyariite ore, mica schist and massive. Most of the attention has been directed to the mica schist ores, as they are more widely distributed and seem to offer greater economic possibilities than the massive ores. It is evident that the preparation of kyanite for use as a refractory material involves other considerations than the mere elimination of impurities. A concentration process that eliminates impurities satisfactorily may have to be followed by some additional treatment, since the final product must be of a coarseness and size ratio that will make it suitable for refractories manufacture. So far in the investigation at the Southern Experiment Station of the U.S. Bureau of Mines only the concentration problem has been considered, and this paper is intended as an interim report. Ores The schist ores contain 1 to 9 per cent of kyanite crystals embedded in mica and quartz, with smaller amounts of graphite, garnet and iron oxide and minor amounts of other heavy minerals. The garnet content varies from a trace to a few per cent. The minerals are easily released by moderate grinding. The size of the kyanite ranges from fine needles to crystals 1 1/2 in. long, 1/2 in. wide and 1/4 in. thick. The garnet, quartz and iron oxide grains have a smaller mean mesh than most of the kyanite. The maximum size of the garnet crystals corresponds to about 14 mesh and that of the sand grains is considerably less. Most of the iron oxide is still finer, for the minus 100-mesh size is greatly enriched in Fe²O3. The massive ore consists of radiating masses of kyanite interlocked with quartz, mica, corundum and small amounts of other heavy minerals.

Jan 1, 1938

By B. W. Gandrud, R. G. Meara, O&apos

In 1034 the Southern Experiment Station of the U.S. Bureau of Mines in cooperation with the University of Alabama began an investigation of the availability of kyanite ores as a source of raw material for the manufacture of refractories. Under this program, gravity concentration and flotation tests have been made on two varieties of Georgia kyariite ore, mica schist and massive. Most of the attention has been directed to the mica schist ores, as they are more widely distributed and seem to offer greater economic possibilities than the massive ores. It is evident that the preparation of kyanite for use as a refractory material involves other considerations than the mere elimination of impurities. A concentration process that eliminates impurities satisfactorily may have to be followed by some additional treatment, since the final product must be of a coarseness and size ratio that will make it suitable for refractories manufacture. So far in the investigation at the Southern Experiment Station of the U.S. Bureau of Mines only the concentration problem has been considered, and this paper is intended as an interim report. Ores The schist ores contain 1 to 9 per cent of kyanite crystals embedded in mica and quartz, with smaller amounts of graphite, garnet and iron oxide and minor amounts of other heavy minerals. The garnet content varies from a trace to a few per cent. The minerals are easily released by moderate grinding. The size of the kyanite ranges from fine needles to crystals 1 1/2 in. long, 1/2 in. wide and 1/4 in. thick. The garnet, quartz and iron oxide grains have a smaller mean mesh than most of the kyanite. The maximum size of the garnet crystals corresponds to about 14 mesh and that of the sand grains is considerably less. Most of the iron oxide is still finer, for the minus 100-mesh size is greatly enriched in Fe²O3. The massive ore consists of radiating masses of kyanite interlocked with quartz, mica, corundum and small amounts of other heavy minerals.

Jan 1, 1938

By Hermsdorf, Richard P. E.

AMONG the newer lead smelting and refining plants of the country is that of the United States Metals Refining Co., at Carteret, N. J. Not only is the technical practice here modern and efficient, but exceptional care is taken to assure healthful operating conditions for the employees. One large building houses the entire department, which includes, as its chief units, one reverberatory smelting furnace, one blast furnace, two softening furnaces, one utility reverberatory furnace, two Faber du Faur retorts, five 120-ton kettles, three 60-ton antimouial lead kettles, and one 5-ton kettle for experimental purposes. There is a 10-ton overhead crane in the kettle aisle, which is also used for shipping lead. Other auxiliary equipment is referred to in the outline of operations. A general plan of the plant is shown in Fig. 2, and a general view in Fig. 1. Primary smelting operations are conducted in a 30 by 11-ft. reverberatory furnace with bottom, roof, and upper walls of clay brick, magnesite

Jan 1, 1934

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By O. E. Kiessling

THE Committee-on Production Control, at its meeting held during the last annual session in February, 1930, evidenced great interest in problems of stabilization affecting all mineral industries. . No immediate program of activity for the Committee as a- unit was decided on, however,, and efforts during the past pear have consisted lirgely of further stressing the economic aspects of mineral production and of the action by committee members, :.serving in their individual capacities, in sponsoring constructive changes, in specific, industries. Of greatest interest to the general subject of production control in 1930 was the very definite advance toward better coordination of demand and supply in the petroleum industry. Furthermore, since opinion both within and without the oil industry now favors a constructive program, and with a gradual change in legal precedents, it seems not unreasonable to expect greater progress in the near future.

Jan 1, 1931

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll' in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod'. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By Fred C. Bond, Walter Maxson

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By Walter Maxson, Fred C. Bond

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By G. R. Wilms

A study has been made of the structural changes in polycrystalline high purity aluminum during the tertiary stage of creep under conditions of constant tensile load. It appears that there is no basic modification in the particular mechanism of deformation that characterized the preceding secondary stage of creep, but that the changes in crystalline structure produced during the tertiary stage are only a consequence and not a cause of the accelerated strain. Intercrystalline fissures were observed on entry into the tertiary stage, and these might supplement the accelerated rate of strain owing to local stress concentrations. There is evidence that the formation of these fissures may be associated with the presence of surface imperfections, and it is suggested that a more generalized treatment of the results may explain certain creep characteristics of commercial alloys. IN previous work'-4 a study was made of the changes produced when specimens of annealed aluminum were deformed at various temperatures and rates of strain, especially under conditions leading to creep under constant tensile load. It was shown that, as the temperature was increased or as the rate of strain was decreased, elements of the substructure produced within the grains became coarser, and with the strain rate constant at a given temperature, their size tended to an equilibrium value. The preliminary process of the breaking down of the grains into a substructure was identified with primary creep.' The subsequent equilibrium, condition was associated with secondary creep. The question then arose whether the tertiary stage corresponded to any further significant change in the substructure. The question is also of interest in view of the opinion, expressed for instance by Andrade,5 that the tertiary stage is merely an accelerated rate of strain due to the reduced area of section of a specimen under continuous tensile load, and the other opinion, as suggested by the observation by Sully, Cale, and Willoughby6 of a tertiary stage in com-pressive loading, that this third stage is a real effect in its own right. The object of this paper is to record some observations on the tertiary stage of high purity aluminum. Experimental Procedure The material was aluminum of 99.98 pct purity as previously used. The specimens had a rectangular section of l/8 x l/2 in., and extensions were measured over a 1 in. gage length. After machining to shape, the specimens were annealed to give a standard grain size of 0.2 mm and then electropolished. The general procedure involved metallographic and X-ray diffraction examination at progressive stages of elongation (marked by arrows on the curves shown in Figs. 1 and 2), the specimen being extended to fracture under constant load at a given temperature. The X-ray tests were made by the back-reflection method from a stationary specimen, using CoK radiation. The longer edge of the micrographs in the paper corresponds to the direction of applied stress. Results The previous work showed that, in the secondary stage of creep in aluminum, three basic types of structure could be developed according to the temperature and rate of strain. These were: 1—slip, which predominated at the lower temperatures and higher rates of strain and produced the finest and least perfect substructure; 2—cell structure, which superseded slip as the temperature was raised and the rate of strain decreased and which was characterized by a coarser and more perfect structure and an absence of slip lines; and 3—a stage termed "boundary microflow," which predominated at still higher temperatures and lower rates of strain when the cell size had increased and become comparable

Jan 1, 1955

By F. H. Buttner, E. R. Funk, H. Udin

Gold wires, 5 mil in diam, are found to creep viscously up to approximately 5.5x106 dynes per sq cm around 1300°K. Beyond this point, an additional slip mechanism appears. The average coefficient in the viscous range at these temperatures is 18.9 ± 7x10 12 poises. This observation and other visual observations made during the experiments agree with Herring's predictions. EARLY creep studies by Chalmers on single crystals of tin produced some of the first experimental evidence to suggest that metals deform viscously under very light stresses. That is to say, over a small initial stress range up to 150 g per sq mm, the single crystals of tin elongated at a rate proportional to the stress. The proportionality constant between strain rate and stress is by definition the coefficient of viscosity. Chalmers named this range of proportionality the microcreep range. One of the first theoretical attempts to explain the microcreep phenomenon was given by Kauzman,' who applied Eyring'sQ eneral statistical mechanical theory of shear rates to creep data then available. From the rate theory, he deduced the general hyperbolic sine law for shear rate on the assumption that the distortion of the reaction path due to stress is negligible and that the system is an infinite continuum. In order to fit the available data to the equation, it was necessary to assume that creep occurs by shear of rather large blocks of material, rather than by an atomistic shear process as in diffusion. The size of the shear units was shown to increase with increasing temperatures and lower stress, or lower strain rates. In applying the hyperbolic sine law equation to the microcreep data of tin, it was shown by Kauzman that the unit shear blocks became quite small, which suggested to him that microcreep might be a self-diffusion process. Making this an assumption, Kauz- man reworked the rate theory and arrived at an equation where the shear rate is proportional to the stress. In the form of viscosity coefficient, the equation is: o- _ \LkT V = 2qAlA where u is the stress; S, the shear rate; X, the distance in shear direction moved by flow units relative to one another in the unit process; L, the distance between layers of units of flow; T, the absolute temperature; k, Boltzmann's constant; qAL, a constant proportional to the size of flow units; and kT A, the diffusion coefficient = ------kTe-Q/RT = K X2 h Kauzman applied the expression to molten lead with a fair degree of success, the calculated viscosity being low by a factor of four. For solid lead the result is 5000 times too high. Taking q = 1, and X = dA = L = 21 = nearest neighbor distance, Udin, Shaler and Wulff8 found the equation low by a factor of lo7 for solid copper. On the basis of the discrepancy in lead, Kauzman indicated that microcreep is probably not a simple diffusion process of molecular shear units, but one involving preferential diffusion paths, or even that diffusion in solids does not involve shear at all. Cottrell and Jaswon4 treat the microcreep phenomenon on the basis of slow moving dislocations and apply it to Chalmers' data on tin with fair success. Nabarro Suggested a microcreep model in which mass movement in the direction of pull is effected by the diffusion of holes. The tension on the crystal effectively creates a greater hole concentration at regions near the crystal surfaces perpendicular to

Jan 1, 1953

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941