Search Documents

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By Joseph Daniels

IN connection with a study of the feasibility of establishing a blast-furnace industry in the Puget Sound region of Washington, possible sources of ore supplies along the Pacific rim were investigated. Many of the South American countries are known to contain important resources of iron, particularly Brazil and Chile. This latter country, because of its position on the west coast and the easy accessibility of its de- posits, appeared to be a logical place to consider as a potential supply for the Pacific Northwest. Accordingly, a brief field study was made of the deposits in September, 1924. Attention was confined to a limited number of properties on the west coast in the provinces of Antofagasta, Atacama, and Coquimbo. Passing consideration was given to the question of coal resources, and a short visit was made to a blast-funace plant at Corral in southern Chile which had been operated for a limited period as a producer of pig iron. In the following paper, a brief outline is given of the general observations made and of the salient facts rioted in the time available for the general study.

Jan 1, 1926

By Elton A., Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11 mile bus ride up Railroad Creek to Holden. All freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting.

Jan 1, 1949

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By Philip B. Bucky

WITH the exhaustion of the sections of iron ore bodies amenable to opencut mining the iron ore miners raise the question: "How can we mine the extensions of these ore bodies in depth with the same costs as obtained in opencut work?" This question brings to the fore the relationship between mineral exploration and research on mining procedures. The iron miners must either find new de? posits amenable to their known methods of mining or develop new mining methods for deep deposits. It is understood that the oil companies will spend $30,000,000 next year in the search for new oil fields. How much the metal mining companies will spend in the search for new ore bodies is unknown, but without doubt the amount will run into several millions of dollars. If the mining companies that concern themselves with metals, nonmetallics, and fuels will set aside a substantial sum for fundamental and applied research in mining methods, they can not only lower their costs but increase their reserves thereby. Any increases in mining efficiency automatically result in increased ore reserves at no cost.

Jan 1, 1947

By J. R. Mihalisin, J. S. Iwanski

The response of Inconel "700" to heat treatment has been studied by light and electron microscopy combined with X-ray and electron diffraction techniques. A heat treatment which vesults in low ductility for this alloy appears to be associated with the formation of MC carbide in a Widmanstdtten distribution. This type of precipitation can be suppressed by suitable heat treatment with concurrent increase in ductility. Various other phases precipitated in this alloy are also identified. RECENT studies of commercial nickel base su peralloys have demonstrated the importance of the morphology of carbide phases upon physical properties.' For example, empirical heat treatment studies applied to Nimonic "80" and Inconel "X" have resulted in prescribing double aging treatments for optimum physical properties. These treatments have subsequently been related micro-structurally to grain boundary carbide morphology.2 The purpose of this study was to obtain information about the morphology and identity of some of the phases precipitated in Inconel "700" after heat treatment. It was hoped that some correlation could be made of micro structure with heat treatment similar to that observed with Inconel "X" and Nimonic "80." EXPERIMENTAL PROCEDURE Specimens were obtained from a hot-rolled bar of Inconel "700" of the following composition: C Mn Fe S Si 0.10 0707 0.42 0.007 0.12 Cu Cr -A1 -Ti- Co Mo Ni 0.02 -14.90 TM 2.22 27.61 2.92-- Bal. Specimens were prepared in the following heat-treated conditions: (A) 2275°F for 2 hr WQ (B) 2275°F for 2 hr WQ + 2000°F for 1 hr (C) 2275°F for 2 hr WQ + 1600°F for 48 hr. (D) 2275°F for 2 hr WQ + 2000°F for 1 hr + 1600°F for 48 hr. Empirical stress-rupture studies had shown that treatment (D) resulted in optimum stress-rupture life and ductility. Treatment (C), although giving a good aging response, resulted in low ductility. Treatments (A) and (B), respresenting individual. steps in treatments (C) and (D) were added here for microstructural comparison studies. The procedure was to make an optical and electron microscopic investigation supplemented by X-ray diffraction analysis of electrolytically extracted residues. Electron diffraction studies were made utilizing selected area diffraction techniques with extraction

Jan 1, 1960

By Thomas F. Bates

ANALYSIS of the chemical and structural differences in minerals often results in a better understanding of the differences in the geological conditions under which they were formed. The minerals in the kaolinite group differ in the amount of interlayer water and in the nature and amount of ordered and/or random shifting of each 1:1 layer with respect to those above and below it. This paper is a progress report resulting from research on the morphology, structure, and origin of fine-grained minerals, supported by Contract N6onr26914 with the Geophysics Branch of the Office of Naval Research. The purpose of the paper is to present data obtained in the laboratories at The Pennsylvania State College and elsewhere, which reveal some of the details of structure of the minerals in the kaolinite group, and to suggest a number of interpretations that bear upon the conditions of origin of these minerals. Be¬cause most of the work in this investigation thus far has been concerned with the relationships of kaolinite, halloysite (4H2O; endellite), and halloysite (2H2O), must of the discussion deals with these members of the group. The first step in the analysis of the differences in two sets of geological conditions is an evaluation of the differences in the minerals that result. Thus the chemical differences between the montmorillonite and the kaolinite clays corroborate other evidence in support of the view that the montmorillonites are commonly formed when solutions are alkaline and leaching poor, while kaolinite usually is associated with acid solutions and good drainage condi¬tions. It is obvious that the greater the differences in the minerals, the more divergent may be the conditions that give rise to them and the more readily one condition can be distinguished from the other. In the kaolinite group, differences between individual members are small, therefore the differences in condition of origin are presumably subtle and difficult to define. At the same time, the very fact that the minerals differ only slightly makes them more sensitive indicators of the exact conditions under which they and the minerals associated with them were formed. Since clay minerals are being used more and more to evaluate the nature, value, and mode of formation of economic mineral deposits, an attempt to define these subtle differences would appear worth while. For purposes of the present discussion, the minerals nacrite, dickite, kaolinite, the so-called "fireclay mineral," halloysite (4H2O), halloysite

Jan 1, 1952

The Committee on Nominations is as follows: Pope Yeatman, Chairman, B. B. Thayer, Henry Landes, Robert J. Grant, F. V. Desloge, Albert Burch, C. K. Leith.

Jan 6, 1919

By R. Wild, F. A. Wright

When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest. In recent years good burden preparation with emphasis on uniformly sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility. This paper explores the Linder method of measuring such reducibility. The measurement of reducibility of burden materials must be carried out under conditions duplicating, as nearly as possible, those of the blast furnace stack. This is very difficult since the blast furnace process is a counter-current one, and thus the initial conditions encountered by the solid (gas temperature, composition, etc.) are the result of heat and mass transfer occurring lower down the stack. Any method of burden testing which does not take this into account is, at least to some extent, based on arbitrary assumptions. In an attempt to study blast furnace reactions under non-arbitrary conditions BISRA adopted the SCICE technique as a method of investigation. This technique has been used with a measure of success.' The SCICE technique, however, was found to be too slow for use as a routine test for burden materials and it was decided to construct additional equipment for burden testing. A test was required which would: 1) Be as realistic as possible. 2) Be quick and easy to operate. 3) Give some indication of the breakdown likely to take place during reduction in addition to a reducibility index. After a critical assessment of the reducibility tests which have been proposed it was decided to adopt the Linder test equipment and procedure as a basis for burden testing. THE LINDER TEST APPARATUS AND PROCEDURE The apparatus which was constructed (Fig. 1) was the same as that described by Linder2 except for minor changes in design. Linder also laid down a test procedure which he had derived from the results of investigations on Swedish blast furnaces. The variations of temperature and gas composition during the test were defined; these are shown diagram-matically in Fig. 2. BISRA's intention was to use the standard temperature and gas composition programmes for testing a variety of burden materials and also to investigate the influence of different programmes on standard burden materials, making use of information from the SCICE apparatus wherever this is possible. Up to the present, effort has been concentrated on the first part of the programme, and work on the second part has only just commenced. For each test 200 g of coke and 500 g of burden material were used. Linder had recommended that the coke and burden material should be between 1 and 1 1/2 in. and this was adhered to in early experiments on ores and sinters. Since the eventual aim of this work was to relate the test results to blast furnace operation, it was decided to carry out subsequent experiments using burden material in the size range used in the blast furnace, as far as this was possible. If the main interest was, for example, a comparison of the products resulting from different methods of agglomeration, then there would be advantages in using burden materials as close as possible to a standard size. After the charge had been placed in the reaction tube and this had been connected to the gas supply, rotation of the reaction tube at 30 rpm was started and the reduction programme was commenced, the gas temperature and composition being manually controlled according to the programme shown in Fig. 2. After the reduction test the charge was cooled in a nitrogen atmosphere. It was then removed from the reaction tube, the coke and burden separated, and the extent of burden breakdown assessed by screening it at 10 and 30 mesh. The extent of reduction was then

Jan 1, 1964

By AIME AIME

THOUGH the Annual Meeting of the Institute-officially numbered 158 on the records was delayed a bit at the start by low steam pressure on the locomotives bringing members to New York, the crowd that finally arrived more than lived up to expectations, and the technical program had few difficulties because of absent authors or lack of competent discussers. The transportation difficulties were occasioned by the fact that Monday, Feb. 15, was the third coldest day in the 72 year history of the New York Weather Bureau, the official temperature being 8 below zero. The New York Central's premier train, the 20th Century, due at 9:30 a.m., arrived about 6:30 p.m., and the Commodore, another crack train from Chicago, was about equally late.

Jan 1, 1943

By R. W. Raymond

CLARENCE King born January 6,1842, at Newport, R. I. His ancestors on both sides mere New Englanders, of English blood, and among them not a few distinguished themselves in art, science, politics or commerce. His grandfather, Samuel Vernon King (partner in 1803 in the house of Talbot, O1yphant & King, later known as King $ Co.), was a pioneer in the China trade, and four of his sons succeeded him in the business. Three of the four died in the far East; and one of

Jan 1, 1903

By Archer E., Wheeler

COPPER operations in the Congo mean the operations of the Union Miniere du Haut Katanga, because there are no other copper industries there. There is a mine at Bwana M'Kubwa, a little way to the South, in Rhodesia, which has been operated on a small scale, and-another farther south, the Falcon mine, but in quite a different section of the country. This Bwana M'Kubwa mine has recently been reorganized financially and the Minerals Separation interests have taken an extensive share in it, so that it may come into operation. The Union Miniere's operations are in Katanga, the most southeastern province of the Belgian Congo, and the company's concession is in the southeastern part of that province. The usual route for going into the country is by way of Cape Town, thence over the South African Railways through Kimberly and Mafe- king to Bulawayo, then by the Beira, Mashonland and Rhodesia Railways to the Rhodesia-Congo border, passing Victoria Falls on the way, and finally by the Belgian road, the Chemin de Fer du Katanga, to Elisa- bethville, the African headquarters of the company. From Cape Town to the border it is about 2150 mi. and from the border to Elisabethville about 158 mi., making a little over 2300 mi. from Cape Town, by rail.

Jan 1, 1924

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By A. E. Austin, J. R. Doig

Ti-Cr alloys age harden after B-quenching by formation of an W-phase. The structure and orientation of this transition phase have been determined. The hardness ap-pears to be caused by strain in the B-matrix produced by concurrent enrichment of alloy content in the W-phase. EARLY studies of age hardening in B-stabilized titanium alloys revealed the formation of a transition phase named o' This phase was detected by X-ray diffraction in binary alloys of Ti-Fe, Ti-Cr,

Jan 1, 1958

By R. P. Carreker, R. L. Fullman, J. C. Fisher

CREEP tests are usually constant load tests. As deformation occurs, the cross section of the specimen changes so as to maintain approximately constant volume. Until necking starts, A _ l0 A0 - 1 where A is the cross-sectional area, 1 is the specimen length, and the subscript o indicates initial values. Thus, during a tensile creep test under constant load, the stress increases in proportion to the elongation. A A, 1, where S is the stress and F the load applied to the specimen.

Jan 1, 1954

By James Gayley

The paper presented to the Institute in 1910, by H. O. Hof-man, on Recent Progress in Blast Roasting,' has called the attention of the iron industry to the adaptability of these processes to the reclamation of by-products such as flue-dust and blue billy, and the better preparation of concentrates and fine ores for use in blast-furnaces. The waste of valuable iron-ore through the production of flue-dust has increased at an enormous rate, and much of it has in

Jan 1, 1912