Search Documents

By A. S. Joy

Vacuum flotation tests carried out according to the method of Schuhmann and Prakash1 have shown that the acid limiting edge of the flotation area for a Brazilian hematite, in the presence of dodecylamine, is a straight line of slope approximately unity. The flotation tests and the structure, surface ionization, and electrokinetic properties of this hematite have been fully discussed elsewhere. 2 The numbers of adsorbed H+, and OH- ions and collector molecules have been determined in the range of critical conditions defining the acid limit of the flotation area. The total amine adsorption is shown in Fig. 1 as a set of contours superimposed on the straight part of the flotation area. These were determined by spectro-photometric estimation of the complex formed between residual amine and the anionic dye Orange II.3 The ionic strength of the solutions was kept constant and at a value in sufficient excess of the amine concentration to ensure that the diffuse part of the double layer was populated predominantly by indifferent ions. Adsorption of H+ and OH- in the absence of amine was found by potentiometric acid-base titration in the presence of hematite.4 The form of the adsorption-titration curves suggested that the hematite surface behaves in an amphoteric manner, and that positively charged sites arise through loss of a hydroxyl ion, and negatively charged sites by loss of a hydrogen ion. On this basis, curves 8 and 9, shown in Fig. 2, were calculated from the titration curves. These show the variation of the numbers of positive (s +) and negative (s—) sites with pH. To distinguish between ionic and other modes of adsorption, zeta-potential determinations have also been made using the streaming potential technique. The influence of amine on the zeta-potential of the mineral over a wide pH range is shown in Fig. 3. The change in charge ?s, due to adsorption of amine ions in the Stern layer, was calculated by applying the Gouy-Chapman theory, as modified by Stem, to the results shown in Fig. 3. The validity of this treatment has been shown by Ottewill and Jaycock.5 The three full lines, Nos. (1) through (3), included in Fig. 2 show the relationship between ?s and pH at three amine concentrations. The general conclusion from the zeta-potential curves is that adsorption of amine causes a reduction in the negative charge on the surface. Comparison of the values shown in curves (1) through (3) of Fig. 2 with the - curve shows that the magnitude of the reduction is comparable with that of s - at any given

Jan 1, 1964

By I. N. Knapp

Introduction.-The special object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such description as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft. in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, boilers, and pipe yard were also carried on 3-in. planking. Drilling Outfit.-This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35 h.p., "oil country" boilers, one double 8 ¼ by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary' jetting swivels, hose, complement of tools, pipes and connections, and. a mud mixer, with engine.

Jan 12, 1914

By M. H. Gidel, D. C. Bard

These notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Unoxidized Vein Matter. Per Cent. Oxygen,......48.00—Quartz, rhodonite, rhodochrosite, sericite, kaolinite, barite, calcite, and hübnerite. Silicon,...... 36.O0—Quartz, rhodonite, sericite, kaolinite, and willemite (very rare). Sulphur,.....5.0—Sulphides of iron, zinc, copper, lead, and sulphates of barium and rarely calcium. Iron,.......5.00—Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese,.... 2.00—Rhodonite, rhodochrosite, and hübnerite. Zinc,.......1.00—Sphalerite, very rare wurtzite and willemite, and tetrahedrite and tennantite. Carbon,......0.50—Rhodochrosite and calcite. Capper,......0.75—Cuprous ( + ) and cupric (—) sulphides. Aluminum,.... 0.50—Sericite and kaolinite. Hydrogen,.... 0.50—Water, sericite, and kaolinite. Potassium,.....0.20—hicite. Lead,....... 0.20—Galena. Arsenic,......0.10—Tennantite and enargite. Barium,......0.10—Barite. Calcium,.....0.10—Fluorite, calcite, and rare gypsum. Antimony,.... 0.02—Tetrahedrite, famatinite, and silver sulphantimonites. Fluorine,.....0.05—Fluorite. Silver,.....1 —Argentite, and sulphantimonites. Tungsten,.... —Hübnerite. Phosphorus, • —Wavellite. Bismuth,' .... 0.05—Sulphide (?) Tellurium,... 1 —Telluride (?) Selenium,.... —Selenide (?) Cadmium,.... —Sulphide (?) Gold,..... —Native and telluride (?)

Jan 1, 1914

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

P,, and v, may now be solved for by trial and error between Eqs. 2 and 3, by assuming time approaching zero and equating PI, to P12. Observe that the pressure under the slug, P12 of Eq. 3, does not remain equal to the P1, at the valve in Eq. 2 as the slug proceeds up the hole. To plot the profile of pressure vs depth, it is necessary to express P12 in terms of P11. To do so, the extent to which the original submergence length S changes with respect to time must be analyzed. At the end of time t after injection, the actual value of L in Fig. 3 is The fall-back v,(t) is now distributed in the gas and exerts pressure on the bottom. This, in addition to the weight of the gas, amounts to the difference in pressures from point to point. With the average pressure profile calculable, a true numerical value for the average pressure in the tubing may be obtained. The value of v, must be obtained experimentally, and since v,, S and D are known, the basic Eq. 1 may be solved for the amount produced. Knowing P, and the actual volume of tubing occupied by gas (vat), it is possible to calculate the volume of gas at standard conditions which is present in the

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

Meeting of Oct. 23, 1914.-It was voted to take no action concerning the proposed amendments to Article VIII, Sections 2 and 3, but that they be sent to the membership, as provided by the Constitution, together with a statement of the arguments for and against the proposed changes. It was voted that the following proposed amendment, which had been unanimously approved at the annual meeting of the Institute on Feb. 18, 1914, be sent to the membership as provided by the Constitution, together with the approval of the Board of Directors of this change: Article III, Section 1, paragraph 3, sentences 2 and 3: substitute the following: "Any Member, Junior Member or Associate in arrears for two years shall be dropped from the rolls unless the time for payment is extended by the Directors. A Member so dropped may be reinstated by the Directors on paying the arrears of clues and other indebtedness with which he was charged on the books of the Institute it the time he was dropped. A Member or Associate thus reinstated shall receive the Transactions for the back year for which he pays." It was unanimously voted to extend the sincere thanks of the institute to Samuel A. Taylor, Chairman, and to each member of the several Committees of the Pittsburgh meeting, for the enjoyable and successful meeting which they brought about.

Jan 12, 1914

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

By W. J. Carlson, I. Iwasaki

A previous article reported a combination process for recovering both metallic iron and metallic manganese from the manganiferous iron ores of the Cuyuna Range in Minnesota.' In this process, the iron was recovered by direct reduction and magnetic separation and the manganese was recovered from the nonmagnetic tailing by leaching and electrolysis. The current efficiency during the electrolysis of manganese is quite low, in the range of 60 to 70%, due to the simultaneous plating of hydrogen.2,3 The parameters that affect the current efficiency are (1) the concentrations of the manganese ion and the ammonium sulfate buffer, (2) the effect of autoxidant, (3) temperature, (4) pH, and (5) current density. To study the plating characteristics of manganese metal.

Jan 1, 1969

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By C. E. Gregor

Current modern trends in mining show that hoisting shafts are being expected to fulfill an important ventilation function. However, where rigid guides and supporting structures are mandatory, ventilating power costs will be high, unless the transverse structures (shaft sets) are streamlined. In the complex configurations of hoisting shaft furniture patterns, either for original design purposes, or for the adjustment of an existing shaft, a useful degree of aerodynamic optimization, by reduction of overall resistance, can only be effectively evaluated by model studies in a special purpose wind tunnel, as described herein. The author has shown that, in one particular case, an annual power cost saving of more than $50,000 was indicated, mainly by the selection of buntons and dividers of improved aerodynamic profile. Mining companies are now realizing the advantages that can accrue through proper attention to the aerodynamic aspects of mine shaft design. With progressive demands of civilization for an ever greater supply of coal and metals, and with greater depths of working, higher rates of extraction, advanced degrees of mechanization, and improved standards of environmental health and work comfort, shaft design is becoming an extremely important aspect of mining operations. In addition, because the cost of sinking, equipping, maintaining, and operating a mine shaft is continually increasing, there is a greater incentive to use a shaft for the maximum duty, consistent with economy. The current natural tendency is therefore to sink multi-purpose shafts, to install as much equipment as is safely and effectively possible to operate; and then, over and above all these functions, to use the shaft to its maximum possible ventilating capacity, as a major, or auxiliary, airway. Clearly, this latter additional function can only be employed at a significant cost, since the most economic operating airways are smooth-lined and devoid of internal rigid furniture. It is true that hoisting functions can be carried out in such shafts if rope guides are used, but only under restricted conditions. Where a manway must be provided, fixed guides and supporting structures are mandatory, and ventilation costs become accentuated. It is generally recognized that the prime element of cost in ventilating a mine can be represented by the power required to drive the fan unit. It is also known that the largest component of total mine resistance is that of the downcast shaft, where this shaft is equipped with rigid guides for hoisting purposes. The pressure loss varies directly as the resistance of the shaft, in accordance with a modification of the Atkinson equation p = RQ2/3600. Furthermore, the air horsepower drawn is given by the equation AHP = (p x 0/33000. Therefore, the power required to drive the fan unit varies as the resistance of the shaft and the cube of the air quantity. Clearly, if Q is a specified minimum, then the only way to minimize the pressure loss (and the power costs) is to reduce the shaft resistance R. (See Table I for a list of symbols.) The resistance to airflow of a shaft equipped with rigid guides and supporting structural sets consists of two components which, for the sake of analytical simplicity, can be regarded as additive. 1) Frictional resistance, represented by the viscous frictional forces within the boundary layer, as air flows along the surfaces of the walls and the periphery of the vertical elements (guides, pipes, cables, ropes, etc.) of the furniture. The friction loss can be readily calculated by the Atkinson equation, after selection of a suitable value for the friction factor K from the McElroy compilation.' KxLxO xQ2 5.2 xA3 Friction loss can be minimized by lining the shaft walls (particularly if of circular or elliptical cross-section) with a smooth continuous lining of monolithic concrete.

Jan 1, 1968

By D. W. Duncan, A. Bruynesteyn

An ore containing chalcopyrite was microbiologically leached in 6 ft columns at particle sizes ranging from -2 +1 ½ inches, to -3/8 + 3/16 inches. The rate of leaching increased exponentially as the particle size decreased. The controlling factor was the active leaching volume made up of the particle surface area and the depth of penetration of the bacteria and leach liquor into the particle. This volume became an increasingly larger part of the total volume as the particle size decreased. The sample under test leached poorly at larger particle sizes and it was calculated that under commercial conditions, it would produce at best a pregnant solution containing 100 mg/l (0.2 lb/ ton) of copper per 100 ft of dump height.

Jan 1, 1974

By John T. Ryan

FOR the first ten months of 1942, on which data are available at the time this is written, the coal-mining industry achieved a most creditable safety record, and ha1 figures for the year may show a record surpassing that of 1941 in which the industry reached the best accident rate in its history. The ten- month accident rate for both bituminous and anthracite mining in 1942 was 2.197 fatalities per million tons of coal mined, compared with a revised rate of 2.271 for the same months of 1941. The bituminous rate decreased from 2.139 in 1941 to 2.039 for ten months of this year, and the anthracite rate shows a reduction from 3.707 to 3.699 for the same period.

Jan 1, 1943

By Frank J. Anderson

IN the cement region of the Lehigh Valley, a difference of 2 to 3 pct in CaCO3 can make or break a new quarry development, and experience of the Dragon Cement Co. has shown that values of calcium carbonate, as reported from churn drill samples, have been increased as much as 6 pct on the average when the same area was diamond drilled. This calcium carbonate increase consequently lowered the values for silica, iron, and alumina, and made these sections much more attractive. Since 1950, the Dragon Cement Co. Inc. has been engaged in extensive diamond drilling in the local limestone of the Northampton, Pa., region, known as the Jacksonburg formation, and in the Lebanon, Pa., region in the Annville limestone, both of Ordovician age.

Jan 12, 1954

By T. J. Whalen, M. Humenik

The liquid surface tension of copper-nickel ad copper-nickel-titanium-carbon alloys and the wettability of titanium caybyde by these alloys have been measuhed. It was found that the surface tensions of the binary copper-nickel alloys Lie on a smooth curve between the end members, copper and nickel. The addition of small amounts of titanium and carbon has nO effect on the surface tensions of copper-nickel alloys. Small additions of nickel to copper significantly reduce the contact angle of Ike alloy with titanium carbide. From a Gibbs treatment, nickel is shown to be adsorbed at the titanium carbide-alloy interface. X HE microstructure of two-phase materials has been shown to be influenced largely by the interfacial energies between the phases present.' , In systems prepared by powder metallurgy techniques and densi-fied in the presence of liquid phase, a precise analysis of microstructure and interfacial energy relationships requires a knowledge of the solid-solid interface energies and liquid-solid interface energies. However, marly metal-nonmetal systems are characterized by the "sweating" of the liquid during sintering, and in these systems wettability is a principal consideration. The wetting in turn is dictated by the various interface energies of the system, as shown in Fig. 1 for a liquid drop formed on a solid substrate. The equation which expresses the vectorial balance of surface forces in the horizontal plane, at the point of contact, A, is given by: where ssv = solid-vapor interface energy sSL = solid-liquid interface energy sLV= liquid-vapor interface energy 6 = contact angle measured through the liquid phase. The angle and the surface tension, slv, can be measured accurately by the sessile drop method.3, The absolute value of the surface energy of the solid cannot be determined by this method, but with reasonable changes in the composition of the liquid only, the value of ssv can be considered constant. The changes in contact angle, then, can be attributed to changes in sSL and sLV and since sLV can be measured, the changes in sSL can be determined. Several studies have indicated that the surface and bulk properties of solid alloys can be correlated with electronic structure. The catalytic activity of copper-nickel alloys was reported to follow the dband vacancies in these alloys.5 Nickel has been considered to have 0.6 holes per atom in the d-band. The addition of copper to nickel is thought to bring about a filling of the d-band of nickel, since each copper atom contributes one electron. Thus, at an atomic concentration of 60 Cu-40 Ni (62 wt pct Cu-38 wt pct Ni) the d-band is believed to be full, and magnetic measurements support this view.6 If the electronic structure is influencing a property of the alloy, this property should show some sort of discontinuity as the composition changes from one side of the 60 Cu-40 Ni composition to the other. Since the catalytic activity can be considered as a surface property of the alloy, it is logical to assume that other surface properties, such as surface tension, may also be influenced by electronic structure. The suggestion has been made that there is a correlation between the solid titanium carbide-liquid Cu-Ni alloy interfacial energy and d-band filling.7 One purpose of this investigation was to determine if the changes taking place in the electronic structure with compositional changes in the solid copper-nickel alloys were reflected in the surface tension values of the liquid alloys. Such a change, if present, would lend support to the suggestion that one can refer to discrete energy bands in the liquid state. Other purposes of the present study were to investigate in detail the wettability in the system copper-nickel-titanium carbide, and to discuss the possible processes which take place during wetting in this system.

Jan 1, 1961

Sept. 3-8, AIME, Fall Meeting, Industrial Minerals, Minerals Beneficiation, Mining, Geology, & Geophysics, Iron and Steel, and Coal Div., Palmer House, Chicago. Sept. 3-13, AIME, Chicago Section, Centennial of Engineering, Chicago. Sept. 5-8, Engineers' Council for Professional Development, annual meeting, Hotel Sheraton, Chicago. Sept. 11-13, American Institute of Chemical Engineers, Palmer House, Chicago, Ill. Sept. 13, Columbia Section, AIME, Canadian Institute of Mining and Metallurgy, joint all-day meeting, Metaline Falls, Wash. Sept. 18, AIME, Utah Section, Newhouse Hotel, Salt Lake City. Sept. 20, Colorado Section, AIME, Denver. Andrew Fletcher, speaker. Sept. 22-25, American Mining Congress, Metal and Nonmetallic Mining Convention and Exposition, public auditorium, Denver. Sept. 23-25, Institution of Mining and Metallurgy, symposium on mineral dressing, Royal School of Mines. London.

Jan 1, 1952

By Leonard R. Weisberg

The general properties of diffusion in GaAs are reviewed. A total of .fourteen atoms have been studied to date, and activation energies for eleven reported are (in ev): Ga (5.6), As (lo), Zn (2.49), Cd (2.43), Sn (2.5). Mn (2.75). S (4.0). Se (4.2). Ag (0.33), Cu (0.52). and Li (1.0). The dijfusion of the first eight atoms, as measured by Goldstein using radiotracer techniques, established the principle of sub lattice diffusion for both host and impurity atoms, since atoms substituting for gallium have lower activation energies than those substituting for arsenic. The diffusion constant of interstitial copper has been determined for the first time by Hall and Racette using heavily doped p-type samples in which interstitial copper predominates. The anomalous behavior of zinc, which has an abrupt diffusion front and a strong dependence on zinc concentration, has recently been quantitatively explained in terms of an interstitial-substi-tutional equilibrium-diffusion mechanism. Lithium and silver diffuse mainly interstitially, while the diffusion of phosphorus is complicated by the continual formation ofGap. Junction-migration measurements indicate diiferent results than radiotracer techniques, and this is one problem that still remains, together with discrepancies in cadmium-diffusion results, and an unexplained dependence of impurity diffusion on arsenic pressure. BESIDES the usual insights into the behavior of atoms in solids, studies of diffusion in semiconductors have additional importance for device applications. In fact, the amount of diffusion studies performed on a semiconductor might serve as a simple barometer of its technological importance. Thus, the information accumulated for GaAs is not yet quite comparable to that for germanium or silicon, but considerable knowledge is available. The diffusion of at least fourteen atoms has been investigated for GaAs, and the diffusion constants have been determined for eleven of these. Interesting results were found for GaAs that elucidated problems not previously solved for germanium or silicon. For example, the interstitial-diffusion constant for the very fast diffusant, copper, was first measured in GaAs. Also, solutions for interstitial-substitu-tional equilibrium diffusion in extrinsic material were provided first for GaAs, although they are ap- plicable to germanium, silicon, and other semiconductors. Studies in GaAs firmly established the concept of sublattice diffusion, which should have application in many different compound systems. The purpose of this paper is to review briefly the general state of knowledge concerning diffusion in GaAs. First some general aspects of diffusion will be covered, and next attention will be given to the results mentioned above. Diffusion in GaAs has been measured both by radiotracer and junction-penetration techniques, and some discussion will be given of differences in the two sets of results. The comprehensive work of oldsteinl-' has served as the primary reference for the diffusion of well-behaved substitutional atoms in GaAs. Since a review has recently been presented of many of these reults, details of the diffusion data will not be repeated. Neither will any discussion be given of the experimental techniques of diffusion measurements, except to note here, in passing, the simplicity and effectiveness of the precision lapping device employed by Goldstein.' I) EXPERIMENTAL RESULTS AND DISCUSSION A) Summary of Experimental Results. Diffusion constants D = Do exp(E/kT) have been determined for eleven atoms in GaAs: a,' AS,' n,'" Cd,'" n,' n,8 s, e,' Ag,O CU," and i." These results are summarized in Table I. In addition, diffusion was investigated for phosphorus,4'12 germanium,I3 and ilicon,' but Do and E were not determined. Radiotracer techniques were used for most of the studies except for lithium, where a combination of chemical and electrical techniques was employed, and germanium and silicon, where junction-migration techniques were applied. The diffusion of zinc, manganese, sulfur, and tin was also measured using junction migration.13'14 Goldstein demon-

Jan 1, 1964