Search Documents

By J. C. Vaughan, John Chapman

Although a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron arc known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the solubility of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 15.8 per cent silicon. EXPEBIMENTAL METHOD There are two general methods by which the solubility of a gas in a molten metal may be determined. In the first, which Sievertsl employed, the gas is measured from a burette into the enclosure containing the metal and the amount absorbed is found by subtracting from the total volume that of the dead space in the container. The second method, which was used successfully for pure liquid iron, is to expose the molten metal to the gas until absorption ceases, then to solidify and analyze the metal. In either method the stirring produced by inductive heating prevents the development of a stagnant layer at the metal surface and ensures actual attainment of equilibrium. Obviously the second method is accurate only when the saturated metal is capable of solidifying without gas evolution. Since the rate of solution of nitrogen in iron is increased by the presence of silicon, it was to be expected that the rate of evolution would be correspondingly increased and for this reason the first method was selected. A sketch of the furnace is shown in Fig. 1. A small high-frequency coil having 17 turns fitted closely around a fused silica tube, 2 in. in diameter, in which was placed, on a bed of 60-mesh alumina sand, an

Jan 1, 1940

By David B. Reger

Widespread wildcatting for new supplies of natural gas and the beginning of importation from the southwest characterized the petroleum industry of West Virginia during 1944. Within the state, drilling for oil did not increase but. more gas wells were completed than in any previous year since 1937. Out of 40 wildcats drilled there were 25 gas discoveries and 15 dry holes. No commercial oil was found in the 40 wells. The proved limits of several oil pools were slightly extended by marginal drilling, resulting in 1300 acres of new oil territory, although no distinctly new pools were found. At least four new gas pools were assuredly discovered and various successful wildcats indicate future pools or wide extensions. The new proved gas territory, in definite new pools and definite extensions, is about 34,000 acres. A considerable net decline of proved oil has occarred and probably a slight decline of proved gas reserves. The account of operations, as gathered from trade journals and other reporting services, shows that 918 new wells were drilled, resulting in 71 oil wells with 613 bbl. of daily new production; 577 gas wells with 305,372,000 cu. ft. of daily open flow, and 142 dry holes. Also, 107 old wells were drilled to deeper sands, with 22 bbl. and 12,327,000 cu. ft. of added production. On the new wells the oil average was 8.6 bbl. per well per day, and the gas average was 529,241 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 15.47 per cent. On deeper drilling the ratio of failures was 19.63 per cent. Production of oil for the year was estimated by the Oil Weekly as 3,069,000 bbl., as compared with 3,349,000 bbl. in 1943. Production of natural gas for the year is estimated by the author as 200,000, 000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 223,789,000,000 cu. ft.t in 1943.

Jan 1, 1945

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By J. L. Rodda

The desirability of a uniformly sized abrasive for metallographic polishing has probably been recognized in a general way for a long time. Certainly all metallographers have recognized the damage that can be done to a polished surface by a piece of grit, especially if one of the softer metals, such as zinc or aluminum, is being polished. It is to be doubted, however, whether many metallographers have had any adequate idea of the particle size of the abrasives they were using or of the range of sizes encountered in any given grade of abrasive. At any rate, the descriptions of abrasives for metallographic work found in the literature are generally very meager. It was with the idea of securing an abrasive with a limited range of particle size that a study of this problem was commenced. Commercial abrasives, even when recommended for metallographic work, are made up of particles of varying sizes. One such abrasive contains some particles so fine that they remain in suspension for days and other particles so coarse that they settle at the rate of 3 in. per minute. It is evident that the coarsest particles are over 100 times the diameter of the smallest ones, or over 1,000,000 times the volume. The hopelessness of avoiding scratches under these conditions is evident. Vanderwiltl has described a laboratory method for grading abrasives in which the elutriator is used. Le Chatelier's method, described by Goereq2 also makes use of an elutriator. However, the elutriator is too slow for this purpose and requires too delicate a control for the range of sizes desired. The method of stirring up the abrasive in water, allowing it to settle for a given time, then drawing a measured depth off the top of the suspension, has been finally adopted as the simplest procedure. The largest particle in a given portion is then determined by Stokes' law:3

Jan 1, 1932

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By Francis L. Bosqui

The following paper embodies a report which I made on the filter-press treatment of slimes at the Liberty Bell mine, Telluride, Colo. At the time this report was submitted, the management deemed it wiser to defer the installation of so costly a plant as the one required, in the hope that some of the many investigators in the field might soon evolve a cheaper and more perfect method of slimes-treatment, and one better suited to the conditions at Telluride. The Liberty Bell ore consists essentially of quartz and clay, with iron pyrites disseminated through the quartz in very fine particles. There is considerable iron and manganese stain in some of the ore, the latter especially in the clays, which are sometimes quite black. Occasionally particles of galena, zincblende, gray copper and a few other minerals are seen, but they are comparatively rare, and not in sufficient quantity to affect considerations of treatment. Free gold is occasionally seen in the quartz, and one or two instances of mire silver have been observed. The milling-plant consists of an 80-stamp amalgamating mill which crushes through 20-mesh screens; 20 Wilfley concentrating tables, taking out, in iron sulphides, about 2 per cent. of the total ore crushed; and a cyanide plant consisting of two tiers of 33 ft. vats, five in each tier, fed by revolving pipe-die tributers. The slimes overflow from the upper settling tanks through gates with adjustable outlets, and thence to a large canvas-plant, which efects only a small saving. This slimes product, of which about 100 tons escape per day (or 38 per cent. of the total ore crushed), contains about 3 per cent. of dry solids. Of this approximately 93 per cent. will pass a 200-mesh screen. The slimes range in value between $3.90 and $4.87 per ton, the values being about equally distributed between gold and silver. The actual averages for ore and slimes during the years 1900-

Jan 1, 1904

By Thomas W. Gibson

THE Province of Ontario in recent years has come strongly to the front as a producer of metals, especially nickel, copper, silver, and now gold. Of the last named, the output for 1922 was in the neighborhood of $20,000,000. The law governing the mining industry in a community where such develop-ments are taking place will be of interest, therefore, in other places where mining laws are up for revision The first mining of importance done in this province was for copper on the north shore of Lake Huron, where the Bruce mines were opened in 1846. These deposits of copper sulfides, notwithstanding the remoteness from markets and the cost of transportation, were vigorously worked for 12 or 15 years and also intermittently later, but the active career of the mines came to an end in 1875. From first to last, a little less than 10,000 tons of copper was produced, valued at $3,300,000. All the product was shipped to England as dressed ore, contain-ing up to 13 per cent. of the metal. In. 1866, a rich pocket of gold was found on the Richardson farm near Madoc, Hastings County, but was not followed by further discoveries of a like kind and in time the excitement it caused died away. Rich silver ore was found in 1868 on Silver Islet in Lake Superior, a speck of land not larger than a good-sized ball-room. The assemblage of minerals here was practically the same as that at Cobalt, discovered 35 years later, namely, native silver, cobalt, nickel and arsenic; in addition, there was considerable argentite, which has always been scarce at Cobalt. In all, the silver produced amounted to about $3,500,000. The belief persisted that the deposit was not mined out, and in the summer of 1922, some rich ore was extracted from the roof, perilously near the bottom of Lake Superior.

Jan 2, 1923

By James Gayley

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1906.) It is to be regretted that the data respecting the use of dry-air blast, which were presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. It appears from the reported discussion that some of those who took part felt themselves to be at a disadvantage, in considering the economies secured through the use of dry-air blast, by reason of the fact that the data presented covered so short a period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs; and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natu-ral air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jan 1, 1906

This report presents the comments of members of the Institute's Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By Edward Keller

(Canal Zone Meeting, November, 1910.) UNDER the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which was described how multi-manipulations, in a works-laboratory, and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit in, or withdraw from, a muffle a set of 48 cupels as one unit. The front row. (8) of these. are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cupels. This operation is an enlargement of what I have already described in my former paper, and Fig. I shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath was designated as being convenient, but was not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders may be removed from the boiling bath, and the acid or water poured off from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Fig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper. ' Trans., xxxvi., 3 to 18 (1906).

Aug 1, 1910

By W. L. McMorris

The Convertol process was first described in Germany by Muschenborn' in 1952. In the U. S. Fraser' reported this new process in 1953, and Brisse and McMorris" presented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals. APPARATUS, PROCEDURE, AND COAL SAMPLES In laboratory work with the Convertol process a Waring Blender equipped with a speed-regulating rheostat was used for wetting, conditioning, inversion, and retention of the coal pulp. A 5-in. International centrifuge was adapted to dewater the agglomerated clean coal product by installation of a 100-mesh screen inside the regular bronze basket of the centrifuge. Except where otherwise stated, the Convertol testing was performed by the following steps: 1) A 450 to 500-cc coal slurry, containing 24 pct by weight of solids, was agitated in the blender for 10 min at 100 rpm to insure complete wetting and mixing. 2) Eight percent by weight of oil was added to the coal slurry in the blender and agitated for 1 min at 11,000 rpm to result in the phase inversion or agglomeration of oil-coated coal particles. 3) The agglomerated coal slurry was poured onto a 100-mesh sieve and wet-screened for about 2 min to remove most of the ash and some of the water. 4) The material remaining on the screen was transferred into the centrifuge for final dewatering. 5) A portion of the clean coal was immediately weighed out for moisture determination, while the

Jan 1, 1960

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset' that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft. elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 lb. pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 ½ miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in. Fig. 3.

Jan 9, 1916

By E. W. Greene, J. B. Duke

This paper deals with the application of froth flotation techniques to the beneficiation of kaolin clay and phosphate slimes, two very fine particle sized materials. The kaolin problem involves the removal of a small amount of a contaminating mineral (anatase), while the phosphate problem involves the concentration and recovery of a much larger percentage of apatite. Due to these differences, and also different response to flotation, the two problems are discussed in separate parts of the article. An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. 1. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casa-grande1 using a long arm centrifuge to obtain equiva- lent spherical diameters down to 0.2 p on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 p, while the crude kaolin is 509 f'lner than 1.4 p, and the fine fraction 50% finer than 0.46~. For comparison 53 p on the horizontal scale would represent Stokesian diameters which would just pass a 325-mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 times the screen opening. 2 Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 p particles, 0.77 for 3p, 1.65 for 1.4 p and 5.0 for 0.46 p particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate-like particle shapes.

Jan 1, 1962

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By J. C. Sullivan, W. A. Knoll

The sinking of a new shaft at the Newport mine, Ironwood, Mich., was started in May 1931 and completed on Aug. 3, 1932. During this period, 2665 ft. of shaft in granite was completed, at an average advance of 6 ft. per 24 hr. In Novernber of 1930, experimental work was conducted on 65 ft. of shaft through 22 ft. of overburden where ledge was encountered, and this work convinced the operators that all drilling could be done with vertical holes with the blasting relief to a 4½-in. hole drilled vertically in the center of the cut. The reason for not adopting the conventional V-cut was to get away from damaging the shaft steel. The blasting in a V-cut naturally tends to throw the broken material upward, but with the cut as adopted the relief was in a horizontal direction to a large extent. The scheme of mucking employed made it necessary to keep the steel shaft sets within 50 ft. of the bottom at all times. This could not be done without serious damage with a V-cut when blasting in granite. The cut as drilled also broke 10.83 ft. per round of drilling, which was considerably more than the experience with a V-cut in the same material. The extended cut reduced proportionately the delays for charging, blowing smoke and handling drilling equipment in the shaft. Another advantage was the ease in drilling vertical over inclined holes, and the preservation of the proper spacing of the drill holes at the bottom of the cut. Drilling Air was carried down the shaft in an 8-in. flanged pipe line at a pressure ranging from 95 to 100 Ib. This line was extended to within 100 ft. of the bottom, where a valve and a 4 by 4 by 6-ft. tee was connected to it. To each side of the tee was connected a nipple and elbow, the resulting span of the two elbows being about 4 ft. Lengths of short 3-in. hoses

Jan 1, 1940

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By Malcolm C. Bridges, Ian A. Goddard

INTRODUCTION Mount Isa mine is a major producer of both copper and lead-zinc- silver ores. During the 1975/76 year, 4.3 million tonnes of copper ore were extracted at an average grade of 3.4%, and 2.4 million tonnes of lead-zinc-silver ore at average grades of 7.0%, 6.7% and 173 grams per tonnes respectively. Systematic lead-zinc mining has continued for just over 45 years and copper mining for just over 30 years. Virtually all mining is underground. The composite and somewhat schematic longitudinal section of Figure 1 shows the overall distribution of ore at the Mount Isa mine. The mine can be roughly divided into two parts about a central shaft complex: to the north there is predominantly lead-zinc ore and to the south there is copper ore. Underground operations are serviced by three shafts in the central shaft complex (P61, R62 andU62) and another to the south in the copper mining area (X41). Mining is spread over a total strike length of 2.9 km and extends to a depth of 960 m. Currently, lead-zinc ore is being extracted between 15 and 11 levels and is hauled to the central ore-hoisting shaft on 13 and 15 levels. Copper ore is being extracted between19 and 13 levels and is hauled to the central shafts on 19 level. The principal lead-zinc mining methods used now, as they have been over the last ten years, are sublevel open stoping and cut-and- fill stoping, with about equal tonnages of ore from each (Figure 2). Since about 1970, there have been several interesting developments in lead-zinc mining methods and procedures, principally: • the development of an effective method for the recovery of pillars between open stopes and • the evolution of safer and more productive cut-and- fill methods. During this period also, the focus of mining has moved 120 m deeper

Jan 1, 1977

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933