Search Documents

By J. Geertsma

In order to obtain a better insight into the pressure-volume relationship of reservoir rocks a theory of pore and rock bulk volume variations is presented. The theory is independent of the shape of the pores but is restricted to isotropic porous media built up of continuous homogeneous matrix material. The main conclusion obtained from this theory is that only three elastic constants and three viscous constants are required for describing pore and rock bulk volume variations if the porosity is explicitly introduced into the treatment. In addition, reasonable approximations are introduced for various types of reservoir rock, e.g., sandstones, limestones, and shales, which lead to further simplifications of the basic formulas. In consequence there is then a further reduction in the number of deformation constants which have to be determined experimentally. It is shown how measurements of these remaining deformation constants can be performed most conveniently. Finally the application of the theory to reservoir studies is discussed and the translation of experimental results obtained in the laboratory into reservoir behavior is considered. INTRODUCTION The decline of fluid pressure in connection with the withdrawal of fluid from an underground reservoir gives rise to a change in volume of both reservoir fluids and reservoir rock. The volume variation of the reservoir rock results in a decrease of both the pore volume and the total volume of the fluid-filled formation. Whereas the variation in volume of the reservoir fluids with pressure is usually known from PVT analysis, that in the volume of the porous medium is rarely measured, as it is considered of minor importance in reservoir engineering. Nevertheless, certain experimental results' suggest that in a number of cases the neglection of the variation in pore volume may introduce errors into material balance calculations of reservoirs producing above the bubble point. Only a few experimental results on the compressibility of porous rocks have been published. The compressibility of pure quartz and of calcite can be found in a paper by Adams and Williamson'. Botset and Reed' carried out some experiments on the compressibility of loose sands, while Carpenter and Spencer' measured the compressibility of a number of consolidated sandstones, which data were supplemented by Hughes and Cooke5. Hall' finally reported a number of experiments designed to study the influence of the porosity on the compressibility of oil-bearing formations, from which it appeared that, particularly in the low porosity range, the compressibility of the pore volume is important enough to be taken into account. Difficulties, however, arise in applying these experimental results to field cases. This is partly due to the fragmentary nature of the published data. Yet even if more complete data were available, the need for a theoretical background would be strongly felt. Such a background can be partially found in studies carried out by Biot,6,7 who published a theory of elastic deformations of porous materials and their influence on fluid displacement within the pores, by Lubinski8, who studied the stress distribution in an elastic porous medium neglecting pore compressibility, and by Gass-mann" who mathematically analysed the elasticity of packings of spheres. The contributions of Biot intro-duce a number of deformation constants which are impractical for reservoir rocks from an aspect of experi-mental determination. The theory developed by dass-mann is correct but difficult to read. It appeared, how-

Jan 1, 1958

By R. Fawley, M. A. Quader, R. A. Dodd

Stacking fault energies and annealing twin frequencies have been measured for austenitic stainless steels having a) constant 20 wt pct Cr and varying nickel contents, and b) constant 20 wt pct Ni and varying chromium contents. The effect of nitrogen has also been studied and, to a lesser extent, so has the effect of carbon. All measured stacking fault energies plot linearly against the corresponding annealing twin frequencies, suggesting that, for constant prior deformation and grain size, twinning frequency can be used to estimate stacking fault energy. Compositions low in nickel possess the lowest fault energy, while the maximum fault energy within the investigated composition range occurs mound 20 pct Cr-20 pct Ni. Nitrogen has practically no effect on stacking fault energy when increased from 0.005 to 0.05 wt pct, although Planar dislocation glide is associated with higher nitrogen contents; this may be a short-range order effect. Carbon may raise the stacking fault energy a little, and causes pronounced dislocation tangling in deformed alloys. The basically different dislocation structures promoted by nitrogen and carbon, respectively, are not associated with large variations in stacking fault energy, and the reason for the difference remains unknown. INTEREST in the dislocation configurations developed in plastically deformed alloys arises principally from a desire for an understanding of mechanisms of plastic deformation and fracture. Comparatively little basic work has been concerned with austenitic stainless steels, although considerable interest has developed in the fundamental aspects of deformation of these alloys since the suggestion that those compositions deforming essentially by planar glide are particularly prone to transgranular stress corrosion cracking.' Certain facts are well-established. An 18 Cr-8 Ni steel (type 304) has a low stacking fault energy which is increased by higher nickel contents, and the structure of these steels when moderately plastically deformed changes concomitantly from planar to less planar to distinctly tangled dislocation configurations. These changes are thought to relate to changes in stacking fault energy, and considerable effort has been expended in measuring stacking fault energies of austenitic stainless steels through the determination of node curvatures2"4 even though the method has limitations due to formula approximations,5 an upper limit of measurement of 50 erg cm-2 at the most,5 and the necessity of an extremely meticulous experimental technique. Therefore, it is not surprising that only qualitative agreement between different investigators is generally to be found.'-' At high energies where node radius measurements are inappropriate, some use has been made of annealing twin frequencies to estimate relative stacking fault energies, although a recent critical evaluation of the method suggests that it should be used cautionsly with due regard to effects of grain size and prior deformation.6 Finally, there is a question as to whether the structures of some deformed steels are due to ordering effects. In particular, the role of nitrogen in promoting planar dislocation motion has been suggested to be due to ordering,' but similar suggestions have been made for steels having low interstitial contents.4 EXPERIMENTAL Small ingots of austenitic stainless steels (-50 g) were prepared from components exceeding 99.99 pct purity, the nickel and chromium being Johnson Matthey "Specpure" metals. Carbon was added as pure graphite, and nitrogen as CrN. The components were accurately weighed, and it was assumed that the final composition was the same as the nominal composition

Jan 1, 1969

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine's total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By M. W. Clegg

The application of the Laplace transformation to problems in the flow of compressible fluids in porous media has provided a large number of exact solutions. For plane radial flow, however, these solutions are either complex integrals or infinite series and are of little value to the field engineer. In the case of production at constant well pressure, the available approximate solutions me valid for large times only. In this paper it is shown that an approximate inversion formula for the Laplace transform, developed for the solution of viscoelastic problems, is applicable to radial flow problems and provides simple analytical solutions to constant terminal pressure problems. The method may be used to obtain approximate solutions to many problems, including media with radial permeability discontinuities, multi-layer formations and pressure buildup in wells after shut-in. The results are compared with the few available computer solutions as well as the large time solutions, and it is shown that this approximate method greatly extends the time interval over which a simple analytical solution is acceptable. INTRODUCTION The study of transient problems in the flow of fluids through porous media has benefited greatly from the application of transform methods. The use of the Laplace transformation for solving parabolic equations has been widely discussed in the field of heat conduction and diffusion as well as in the petroleum literature. Removal of the time variable with the Laplace transformation generally reduces the problem to a boundary value problem which may be solved by standard techniques. A much more formidable problem then faces the engineer, however, for frequently the transform does not possess a simple inverse. The result is that the general inversion integral must be used and this leads to either an infinite integral or an infinite series, both of which are difficult to handle from a computational standpoint. Asymptotic approximations for the inverse have been known for some time and these yield approximate inverse functions that are valid for very large or very small times — but frequently the times of interest lie somewhere between these two extremes. Therefore, some acceptable approximation valid over a larger interval of time is desirable. During the past few years a number of methods for achieving this have been developed and some of these are discussed briefly in this paper. The relative merits of the various methods are not evaluated here, but some general conclusions reached by other authors are given. One of these methods has been applied to problems associated with the radial flow of compressible liquids to producing wells. In the case of production at constant well pressure, the method leads to simple analytical solutions for a number of standard problems; e.g., homogeneous formation, permeability discontinuities, pressure buildup. These solutions greatly extend the range of validity of the asymptotic ones (valid for large times only) and should be of value in studying the behavior of wells producing under constant pressure conditions. METHOD FOR THE APPROXIMATE INVERSION OF LAPLACE TRANSFORMS Much of the work that has been done on the approximate inversion of Laplace transforms has originated in viscoelastic problems. Apart from the asymptotic approximations,1 one of the first approximate methods was due to Alfrey.2 If (s) is the Laplace transform of f(t) defined by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By W. B. Gogarty, H. R. Bailey

Methods are presented for determining molecular diffusion coefficients by using data from, capillary flow experiments. These methods are based on a numerical solution (presented in a previous paper) of the partial differential equation describing the combined mechanisms of flow and diffusion. Results from this numerical solution are given and compared with the approximate analytical solution of G. I. Taylor. The numerical solution is valid over a much larger time range. These methods are applied to experimental results for the fluid pairs water-potassium permanganate solution and amyl acetate-orthoxylene. Both of these fluid pairs have approximately equal densities and viscosities. Graphical and numerical techniques are presented for deter mining diffusion coefficients from the flow data. Values obtained by these techniques are compared with values obtained by other methods. INTRODUCTION The molecular diffusion coefficient is known to be a variable in determining the amount of mixing in a miscible displacement process. The effect of molecular diffusion on dispersion in longitudinal flow through porous media -has been examined by different investigators. These investigators concluded that at low velocities of flow, the amount of dispersion is approximate1y proportional to the molecular diffusion coefficient. The influence of diffusion on fingering, channeling, and overriding has been mentioned by other investigators.4 Recent studies5,6 have been made on the effects of molecular diffusion in connection with the problem of gravity segregation. Many different methods have been developed for the experimental determination of molecular diffusion coefficients? These methods differ mainly according to boundary conditions selected and analytical procedures used. Nevertheless, all of these methods have the condition in common that the bulk fluids in which diffusion is occurring are stationary with respect to each other. In connection with a series of papers on mixing in capillary flow,8-10 Taylor suggested the use of a flow method for determining molecular diffusion coefficients. Additional studies 11-13 have been conducted on miscible displacements in capillary tubes, but the data from these studies were not used for the specific purpose of determining diffusion coefficients. The flow method proposed by Taylor results in a single value of the diffusion coefficient for the fluid pair used in the displacement experiments. This single value represents the true value for the fluid pair when the diffusion coefficient is independent of concentration. If the diffusion coefficient is a function of concentration, the single value obtained by the flow method gives an average value for the coefficient of the fluid pair. These average values are based on diffusion taking place over the entire range of concentration, i.e., from 0 per cent of one fluid to 100 per cent of that same fluid. In field applications of the miscible displacement process, gradients occur over the same range of concentration as are found in the displacements in capillary tubes. Molecular diffusion coefficients obtained from the capillary flow method should, therefore, be especially relevant to field operations. This investigation was undertaken to evaluate the feasibility of obtaining molecular diffusion coefficients from capillary -flow experiments. In making this evaluation, diffusion coefficients were first determined for two systems from data obtained in capillary flow experiments. These values of the diffusion coefficient were then compared to values obtained by other methods. MIXING IN CAPILLARY FLOW—THEORETICAL The theoretical basis for determining molecular diffusion coefficients from capillary flow experiments is the partial differential equation relating the mechanisms of flow and diffusion. For the case of laminar flow and with a fluid pair having equal densities and viscosities, the equation is given by

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By C. H. Samans, G. F. Tisinai

HARDENING and embrittlement of the ferritic chromium stainless steels at temperatures near 885 °F have been known for a long time.' However, no satisfactory explanation has been given. Both ordering and precipitation hardening have been suggested. Fisher, Dulis, and Carroll2 discovered a chromium-rich body-centered-cubic precipitate in embrittled alloys. Subsequently, Williams' and Wright4 also have found evidence of this body-centered-cubic constituent. William's hardness, electrical resistance, and magnetic studies led to his proposal of a new constitutional diagram for the Fe-Cr alloys. The new feature of this diagram is the eutec-toidal decomposition, below about 970°F, of the s phase into two stable body-centered-cubic solid solutions, one rich in iron and the other rich in chromium. An observation of Heger5 that the amount of s phase has increased and the amount of chromium-rich body-centered-cubic phase decreased in the interval 5000 to 32,600 hr at 900°F, even though the alloy increased in hardness, casts some doubt on this diagram. If precipitation hardening causes the embrittlement, the precipitate probably is always coherent with the matrix, since no evidence of overaging has been reported. It cannot be stated positively, however, that Fisher's body-centered-cubic constituent is the embrittling phase. According to Preston's data,6 such a chromium-rich phase should have a parameter less than about 0.5 pct larger than that of the iron-rich matrix lattice. Moreover, the constitutional relationships whereby Fisher's constituent forms, and whether it is stable, metastable, or a transition phase, are not yet completely clear. The recent studies of Wright4 and of Lommel,7 as well as the earlier studies of Becket8 and of Hochmann,9 have shown that 885°F hardening occurs in relatively pure Fe-Cr alloys. No evidence of its occurrence or absence in chromium itself has been reported. The rate of hardening in high purity alloys seems appreciably slower than that in alloys containing larger amounts of impurities (chiefly carbon and nitrogen). This may be due merely to the absence of hardening and straining effects from precipitated carbides and/or nitrides. These observations on high purity alloys make it seem unlikely that 885 °F hardening is caused by a constituent containing other than iron and chromium atoms, e.g., carbides and/or nitrides. Wright,4 Lommel,7 and Lena and Hawkes10 emonstrated the accelerating effects of a finely dispersed precipitate of (probably) chromium nitride on the hardening reaction. This appears to be evidence that lattice straining increases the rate of nucleation of the hardening constituent. Some new observations on 885°F hardening are reported here. They show an effect of preheat treatment that should contribute to a better understanding of the 885°F hardening phenomenon. They also clarify a discrepancy which exists in the literature. Some investigators have reported most rapid hardening at 885", whereas others have reported it at 930°F. The present work also shows that 885°F hardening does not occur in electrolytic chromium, and that any long range ordering type of reaction affecting any sizeable part of the volume is unlikely. Materials Studied Table I shows the currlposition of the alloys used in this investigation. In these alloys carbon and nitrogen are present in roughly similar amounts. Presumably both elements precipitate, as carbides and/or nitrides, during the heat treatments given.

Jan 1, 1958

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

By J. A. Snyder, W. L. Finlay

G. Edmunds—Solid solubility is considered to be of either the interstitial or the substitutional type. Is it possible, in a binary alloy as the simplest case, that some of the solute atoms are present in the normal lattice sites (substitutionally or filling lattice vacancies) while simultaneously others are in interstitial positionss One might even ask whether a distribution of the two types may be the normal situation. H. M. Meyer—Metastable states of interstitial atoms occupying vacant lattice sites possibly occur as well as of substitutional atoms squeezed in between regular matrix positions. However (as we know since Hume-Rothery), the solute atoms choose between the two kinds of solutions; consequently, every solute will be unequivocally either substitutional or interstitial in the equilibrium state of the solid solution. M. Balicki—In view of the fact that the authors apparently correlate the analysis of the alloys at the ingot stage with the properties exhibited at the testing stage, I would like to ask whether this is a fully justifiable procedure. In other words, how good are their determinations of solute concentration for correlating them with the mechanical properties. The answer to this question may explain some of the divergencies. Assuming good enough homogenization of the samples and exact determination of mechanical properties the position of the plotted experimental points will depend solely upon the accuracy of composition determination. If this is not accurate, say due to loss or pickup of elements during processing from the ingot to the testing stage, or due to a systematic error in the method employed for obtaining solute concentration data, the points will deviate from their true position and may align themselves along a different curve than the one expected. H. V. Kinsey—We have been studying the creep-rupture properties of titanium-base alloys at 1000°F. In the course of this work, anomalies in behavior of the alloys that would suggest that the material under test was becoming stronger as the test progressed have been observed. If this was so, the most likely explanation that we could think of was that the test bars were absorbing oxygen and nitrogen from the air during the test and were thereby becoming strengthened. In an attempt to determine the strengthening effect of absorbed oxygen and nitrogen the following experiment was conducted. A length of cold-rolled titanium was supplied by the E. I. du Pont Co. Two test bars, having a 1/4 in. diam gauge length, were prepared from this material. One bar was tested in the as-received condition. The second bar was heated in air at 1550°F for 100 hr and subsequently air cooled prior to testing. A testing temperature of 1000°F was employed. The results of these tests are tabulated in table 11. In the author's opinion, is it reasonable to assume that the bar that was exposed to air at 1550°F for 100 hr was stronger because it absorbed oxygen and nitrogen from the air during this heat treatment? W. L. Finlay (authors' reply)—Direct experimental evidence for or against Mr. Edmunds' interesting suggestion will probably never be available. It seems possible, however, that mixed interstitial-substitutional solid solution might well occur with interstitial elements. The less likely possibility of interstitial solution of a normally substitutional element like copper in aluminum was recently discussed at length by the

Jan 1, 1951

By Walter J. Karplus

By means of a finite difference expansion a fluid flow field in cylindrical coordinates with axial symmetry, is simulated by a network of electrical resistors. A series of DC analog computing units, connected to the network bounrlary corresponding to the free surface effectively adjust the network parameterr to satisfy simultaneously Laplace's equation and the borrndary conditions. The system automatica1ly "re1axes" to the correct boundary shape in a fraction of a second. A detailed application of the method to the water coning problem in oil wells is presented. INTRODUCTION The water coning problem in petroleum production is a prime example of a class of problems known as free surface problems. A free surface arises in fluid flow regions when the shape of the boundary of a single phase flow region is affected in some manner by the pressure or potential gradients within the region. When there exists an interface of two fluids of different densities, the shape of this interface will be determined by the relative velocities of the two fluids and will therefore comprise a free surface. Other free surface problems of interest to petroleum engineers include the gas coning, water injection, and gravity drainage probIcms. In each case it is desired to predict the shape of the boundary of the oil zone as a function of the flow rate, the well penetration and the physical parameters and dimensions of the system. Such problems do not lend themselves to the classical analytical treatments of boundary value problems because in this case the boundary of the potential field and the potential distribution within the field are interdependent and must be calculated simultaneously. A further difficulty arises from geometric considerations. Since the fluid flow is of the radial type in most cases, such effective methods as conformal transformation and the hodograph are not applicable. It is the purpose of this paper to present a method whereby free surface problems of this type may be solved rapidly to the desired order of accuracy by means of a combination of a network of electrical resistors and conventional analog computer units. The water coning problem is treated in some detail. Then the procedure for extending the technique to other free surface problems is indicated. FORMULATION Most commercial oil reservoirs consist of an oil-saturated sand, bounded above by an impermeable strata and below by a water-saturated sand. Gravimetric separation results in a horizontal oil-water interface. When an oil well is drilled so that it partially penetrates the oil zone, and production is initiated at a constant rate, the oil-water interface will assume a new shape as a result of the pressure gradients in the oil zone. It should be emphasized that this is a steady phenomenon. After an initial transient period the water phase will be completely static and only the oil will be in motion. The new steady-state shape of the interface, as shown in Fig. 1, depends upon the depth of penetration, d, the thickness of the oil zone, I, the production rate, q, the hydraulic permeability zone of the sand, k, the viscosity of the oil, µ, and the densities of the oil and water, p.,. and pw.. The problem is to determine this relationship. Darcy's law + = - (P f g p z).....(1) it.

Jan 1, 1957

By H. W. R. Wardlaw

This paper shows how the cost of the drilling operation per 100-ft drilled can be related directly to bit weight, rotary speed and hydraulic horsepower variations. This enables optimum drilling conditions to be determined in a rapid and concise manner. The paper also shows how data for such calculations cun be obtained quickly and accurately by the "drill-off" method suggested by Lubinski. Examples are given to illustrate the principles and methods used. INTRODUCTION The problem of drilling oil wells at lowest cost and hazard needs little introduction, since it has been with us virtually from the earliest days of our industry. With better understanding of the effect of the various factors of bit weight, rotary speed and hydraulic jet action, however, the problem has recently taken on a more scientific aspect, and engineers or groups of engineers have been assigned to study many of the facets of this problem not immediately apparent to the general observer. Moreover, the availability of better equipment and materials has enabled certain practices to be adopted which were hitherto impractical or uneconomic. This has paved the way for further efforts to reduce footage costs, and so on. The improvements to be made in drilling technology and cost reduction are by no means exhausted, and we still frequently hear of new records being set and new materials and equipment becoming available. Some of the analytical methods used by the author to assist in promoting faster and more economic methods of drilling, particularly in Venezuela, form the basis for this descriptive study. STATEMENT OF THEORY AND DEFINITIONS In a highly competitive industry, it is no longer permissible to regard penetration rate as the sole criterion for drilling efficiency. Every new technique, however spectacular, must nowadays be viewed in the cold light of whether it will eventually lead to lower cost per foot drilled. In the exposition which follows, therefore, actual drilling rates will play only a secondary role, and attention will be focused on the more important aspect of cost per foot drilled. Changes in drilling factors such as weight and rotary speed will be studied in the light of how they directly affect the cost of operations. The advantage of this method is twofold—(1) cost increments are indicated directly; and (2) the relationships are, surprisingly enough, simpler than those relating to drilling rates. To achieve these advantages, it is necessary to introduce a new unit of measurement which, although unfamiliar, is readily understood. The unit in question will be referred to as the "actual drilling cost factor" and will be designated by the symbol h. The unit is defined as the number of rotating hours taken to penetrate 100 ft of formation. The unit can be obtained immediately from the actual drilling rate (r) in feet per hour; thus, This latter transformation is so easily effected that it may be convenient to use h as an international symbol for drilling cost, and to delay conversion to dollars, bolivars, pounds, etc, per foot until actually required (e.g., for fiscal reasons, etc.). In actual operations, h was found to vary in a relatively simple manner with increases in bit weight. The variation in h with rotary speed was found to be somewhat more complex. However, this also could be enormously simplified by introducing a further factor known as L or relative bit life. The factor L is also defined very simply by dividing 1,000 by the rotary speed (N) in revolutions per minute.

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.' These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965

By R. Maddin, C. H. Mathewson, W. R. Hibbard

According to conventional crystal mechanics, a face-centered cubic single crystal slips on the system {111} <110> which receives the highest shear stress in terms of the stated orientation of the stress axis of the crystal.l However, in brass, the slip process is never as simple as this conventional analysis indicates. There is always a second cooperating plane which contains the same slip direction as the primary plane.2&apos;3 There is still another cooperating slip system commonly called the conjugate system3 previously observed to function with considerable lag only after the rotation due to the action of the first plane had produced a symmetrical condition of equal shear stress on the two systems. In the 1943 Campbell Lecture,4 a slip mechanism was outlined in which the {111) planes moved step-wise in two adjacent <112> directions integrating into the <110> slip direction. "... the slipping process would be visualized as a succession of steps 30" to the right and left of the resultant, microscopically observed, slip direction; a first step setting up the twinned configuration in the single spacing involved and an ensuing slip returning the atoms to the untwinned configuration while completing a fully integrated <110> movement."4 This process is shown diagrammatically in Fig 1 which shows two close packed layers of atoms at a slip site. A movement of the full circles through the "valleys" into the adjacent sites would produce a twin configuration with respect to the open circles. The term, "twin fault," seems most appropriate to define this faulted condition of the lattice. Annealing twins in face-centered cubic metals may arise from preformed nucleii which could be described as twin faults produced by the first movement of this two stage slip process. However, it is clear that this kind of slip does not take place so as to embrace a measurable number of adjacent planes because careful X ray examination has not conclusively shown the existence of ponderable twin lamellae (as in the case of Neumann bands in the body-centered ferrite). In view of the imponderable character of these hypothetical twin faults, the search for evidence of their existence seems restricted to indirect methods. The most obvious experimental technique serving this purpose is the determination by micrographic and X ray methods of the alignment of the composition planes of annealing twins with the former slip planes in axially strained and recrystallized single crystals. In previous attempts of this sort not all of the annealing twins could be traced to slip planes known to be operative in the conventional sense and hence evidence appeared negative or inconclusive. With the discovery of additional slip systems2&apos;3 operating in conjunction with&apos; the major system of highest resolved shear stress in axially strained brass it became apparent that the simple technique outlined above might be re-employed with more gratifying results. If, on annealing single crystals of alpha brass previously strained in tension, twins are found with their composition planes parallel to all three operative slip planes and with no participation of the fourth plane there is good evidence in favor of the existence of twin faults and of the two stage slip process. Experimental Procedure and Resuits Single crystals of alpha brass of the 70-30 composition were grown by solidification from the molten state.

Jan 1, 1950

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel&apos;s Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By F. E. Streigert, J. H. Mallery, A. H. Geisler

The existing data on precipitation in Cu-Be alloys have been reconciled with some new data to present a more complete and rational analysis of the atomic rearrangements involved in the process. Two different coherent precipitates were proposed. Each is responsible for a type of diffuse X-ray diffraction effect. THE nature of the atomic rearrangement involved in the precipitation of the compound y-Cu-Be from supersaturated solid solutions of the copper-base alloys has been the subject of two extensive investigations.&apos;-" he precipitate in this alloy system has a rather simple structure; at equilibrium it has a body-centered cubic unit cell with copper atoms on the corner sites and beryllium atoms on the center site. While a simple mechanism would be expected to obtain for the precipitation process, those which have been proposed do not adequately explain all of the reported data. The purpose of the present report is to rationalize some of the previous observations and to contribute new data on the subject obtained by the usual techniques of structure analyses. The Cu-Be system of alloys represents one of the most extensively investigated precipitation systems, so a detailed review of the pertinent literature on structure is in order. Striations: Since one of the important features of the mechanism—the habit plane—is determined by microscopic examination, microstructural features that have been observed should be considered at this time in order to assess their role in the precipitation process in Cu-Be alloys. One of the most prominent features appears as regularly oriented markings or stripings (ripples or striations) across the crystals on a suitably polished and etched sample of the aged alloy. These have been observed and interpreted by many workers. Masing and Dah14 observed striations in both the a and /3 phases of a 2.5 pct Be alloy, and attributed them to the beginning of the precipitation of very fine y crystals along favored planes of the a matrix and to the local decomposition of the £ crystals into a plus y. These markings were apparent in both the a and /3 phases of the micrographs given by Smith5 for a 2.75 pct Be alloy, while Moore" detected them in the a matrix phase using polarized light. Desch7 attributed the markings to fine precipitate particles lined up on a family of matrix planes like Masing and Dahl had done, and he identified the planes as those of the (111) family, the slip planes of the matrix. The striations were presumably the structure which Northcott- eferred to as "martensitic." He found that this structure was present in samples that had been aged under widely different conditions with hardness values ranging from 160 to 400 VHN. Later Guinier and Jacquet&apos; also found striations in both the a matrix and secondary /3 phase. Their analyses showed that the striations were along (110) planes of the matrix phase, apparently in contradiction of the results of Desch. They found that the striations were developed during aging on the surface of a specimen that had been polished prior to aging.&apos; On this basis they concluded that the striations represented mechanical deformation by slip along (110) planes of the matrix resulting from precipitation stresses.&apos;" Similar but fainter striations were observed in the same manner on an A1-Cu alloy sample, in which the change in volume was much less than for Cu-Be alloys and

Jan 1, 1953

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting&apos; thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification&apos; determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By D. Walton

The effect of small solute additions of Cu on the activation energies for creep A1 single crystals were determined over the range from 78° to 850° K. Below 240°K and above 800°K activation energies were unchanged. Between 240°K and 400°K strain aging causes the creep rate to become vanishingly small and the flow stress was independent of the temperature. Between 500° and 50°K the activation energy was increased to 41,000 cal per mole. NUMEROUS investigationsL have shown that solid solution alloying invariably increases the flow stress. A typical example is documented in Fig. 1. Such increases in flow stress can arise from two general effects: Alloying can increase the long-range stress fields through which dislocations must move by causing appropriate clustering; modification of dislocation densities, and so forth. Alloying can also modify the short-range stress fields that determine the activation energies for thermally stimulated migration of dislocations, such as occurs in some solute atom pinning processes, and so forth. Actually both long- and short-range stress-field effects can occur simultaneously. It was the purpose of this investigation to evaluate the effect of alloying on the short-range stress fields by determining the effect of alloying on the activation energies for creep. The resulting observations also shed some light on the effect of long-range stress fields on dislocation processes. EXPERIMENTAL TECHNIQUE Single-crystal bars (6 in. long 3/8 in. wide and l/4 in. thick) of dilute solutions of Cu in A1 were seeded, so as to provide extensive single slip, with the pole of the tensile axis located in the standard stereographic projection as shown in Fig. 2. Each crystal was grown under an argon atmosphere in a graphite mold containing a large reservoir of molten alloy for the purpose of obtaining rather uniform composition of Cu along the length of the bar. The nominal compositions of the alloys which were produced from 99.99 pct Cu and high-purity A1 containing 0.001 pct Fe and 0.001 pct Si, are given in Table I. Strains, measured by linear variable transformers attached by quartz rods to a 3 in. gage section were sensitive to and the stresses were ap- plied by direct loading of the specimen. Temperatures were determined by thermocouples attached to the gage section of the specimens. Below 400°K the apparent activation energies for creep, Q, were determined by the effect of small, rapid changes in temperature of about + 10°K from T1 to T2 on the corresponding creep rates ?1 and ?2 during primary creep according to where R is the gas constant.&apos; Above 400°K, Q was evaluated from Eq. [1] for the secondary creep rate using temperature changes of about ±20K. A typical set of results is shown in Fig. 3. RESULTS AND DISCUSSION The previously obtained effect of temperature on the apparent activation energy for creep of single crystals of high-purity A12 is shown by the broken curve of Fig. 4. The datum points on the same graph illustrate the effect of dilute a solid solution alloying with Cu on the activation energy between 600" and 750°K. Each plotted point is the average of not less than five independent test values between 600° and 750°K and not less than three at other tempera-

Jan 1, 1962