Search Documents

By J. L. Martin, W. M. Campbell

A new electric logging method, called displacement logging, often gives a direct indication of the presence of mobile hydrocarbons in hydrocarbon-bearing formations. This method is based on the detection of a bank of connate water which is formed between the invading mud filtrate and virgin formation fluids in these cases. The existence of this phenomenon has beer, verified by laboratory studies and by actual field logs taken in known oil sands. INTRODUCTION During the past decade increasing use has been made of conventional electric logs to determine the amount of oil or gas in formations traversed by a borehole. This determination requires knowledge of several factors, such as true resistivity of the formation, formation factor, and water resistivity. Sometimes all of the factors necessary to make a reliable saturation calculation are not available. Also, the computations and corrections which are necessary in such a study often require the services of an experienced log analyst. It has long been the desire of exploration people to have a logging device which will locate hydrocarbon-bearing formations directly without requiring complex interpretation methods. The displacement log, while not completely fulfilling this desire, appears to be a Step in that direction. Basis for the Device The basis for this device stems from a phenomenon which occurs when mud filtrate invades a formation which contains displaceable hydrocarbons. As the mud filtrate invades the formation, most of the oil or gas is pushed out of the invaded zone, leaving residual oil. However, in addition to displacing most of the oil or gas, the connate water is also swept out, since the originally irreducible water is mobile in the presence of a water phase.1,2,3 Tonsequently, this irreducible water piles up as a bank between the virgin oil zone and the invading filtrate. If the mud filtrate is of higher resistivity than the formation water— as is commonly the case—the resulting annular zone, containing the bank of formation water, will be of lower resistivity than either the virgin oil-bearing formation resistivity or the invaded zone resistivity. This resistivity configuration, going from high to low to high again as the distance from the borehole increases, is found only in those zones which contain displaceable hydrocarbons. A device which would reliably detect this low resistivity zone would give a direct indication of mobile hydrocarbons. Illustrations This phenomenon is illustrated in Fig. 1 and 2. Fig. 1 shows a sketch of a zone containing salty connate water plus displaceable hydrocarbons, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 2 shows this zone, together with fluid content and resistivity graphs. after invasion by a fresh water mud. The resistivity pattern on moving away from the borehole is high: low: high. The absence of the low zone phenomenon in water zones is illustrated in Fig. 3 and 4. Fig. 3 shows a sketch of a zone containing salty formation water and residual oil, along with graphs showing fluid content and electrical resistivity vs distance from the borehole, before invasion occurs. Fig. 4 shows this water zone, together with fluid content and resistivity graphs, after invasion bv a fresh water mud. In this case the resistivity pattern on moving away from the borehole is high: low since there is no change in water saturation at the head ol

Jan 1, 1956

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By L. J. Ingvalson, Roy H. Miller

IN 1948, as part of a program to expand the copper tube mill facilities of the American Brass Co. plant at Kenosha, Wisconsin, plans were formulated to convert the 100 ton capacity anode casting furnace at the Great Falls, Montana plant of the Anaconda Co. to the production of 3 in. phosphor -ized billets. The furnace was rebuilt completely and construction was started on an addition to the building. Members of the Great Falls staff visited various billet casting plants to draw upon the experience of other producers of this type of casting. Many features of other plants were incorporated into the Great Falls plant but, in addition, many new designs were made and perfected to make the plant the most advanced of its type. Construction was begun in 1949, with the intention of having the plant in production in the early part of 1951. In January 1951, as the plant was being rushed to completion, the government placed restrictions on the production of copper tubing. As a result, work was halted and the plant lay idle for two years. Interest was reactivated in May 1953 with the lifting of restrictions on copper. Plans were laid to go into production in July and the first charge was taken out July 1, 1953. Basically the plant is designed to produce from cathode copper a 3 in. diam billet, 50 in. long. weighing 110 lb, and containing 0.013 to 0.036 pct P, at a rate of 150,000 Ib per operating day. These billets are to be pierced and drawn into tubing. Furnace The furnace is a 100 ton capacity reverberatory type, gas fired furnace; 21 ft long and 9 ft wide. Gas is introduced to the furnace through two 38 hole Mettler gas burners. These burners are of chrome nickel alloy with four jets per hole. The furnace is charged with cathodes from the Electrolytic Copper Refinery plus return scrap from the casting operation by means of a Wellman Seaver Morgan Co. 7,000 lb capacity charging machine. The charge crane has a 20 ft boom and fork peel provided with an air ram to push material off the peel. The machine travels on overhead tracks and can be moved in any direction. The boom can be raised and lowered and swung through an arc of 180". With well stacked units of 6,000 lb, an experienced operator can put the first charge into the furnace in 40 min. After charging, the steel framed silica brick charge door is put in place and sealed with clay. After melting and skimming off the slag, the copper is blown until an oxygen content of 0.40 pct is reached. The metal is then heated to 2180°F, covered with coke, and poled. Poling is continued until a 3 in. diam test billet, 8 in. long, shows a flat set. The oxygen content is usually 0.030 pct at this time. At the end of poling, a temperature of 2160" to 2180°F is desired. In the side of the furnace opposite the charging door is the taphole slot, extending 36 in. upward from the bottom of the furnace. It is 4½ in. wide at the outside face and widens to 9 in. at the inside face of the furnace. It is filled with a wet mixture of sand, fireclay, and crushed coal. Flow of metal

Jan 1, 1957

By F. G. Miller, T. D. Mueller, L. B. Davidson

A mathematical model of reservoir behavior during one cycle of the intermittent steam injection process is presented in this paper. A cycle of the process is considered to be composed of three stages: injection, condensation and production. The model concentrates on behavior during the production stage. The influence of several parameters on production improvement is described, using the results obtained with a numerical equivalent of the model. Reservoir system parameters considered are thickness, reservoir thermal conductivity, oil viscosity, solution gas-oil ratio and the change in oil effective permeability with temperature. Operating parameters investigated are heat injection rate, steam temperature and cumulative injection time. In the face of considerable uncertainty, the model appears to give a fair prediction of the behavior observed during an actual test. This makes the model a useful means of selecting projects. It is shown that the model may also be utilized to select an optimum set of operating conditions for a particular project. Results of this study show the extent to which production improvement depends on each of the parameters investigated and give an indication of the range of system conditions within which the process would be effective. INTRODUCTION In recent years the intermittent steam injection or steam soak process of oil recovery has become a popular method of improving recovery in reservoirs bearing high-viscosity hydrocarbons. Production improvement due to the process results from heating the reservoir near the wellbore. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three stages: injection, condensation (the soaking period) and production. During the injection stage, high-pressure steam is injected into the reservoir surrounding the well-bore. This study assumes that injection is carried out over the entire vertical section of the reservoir rock that can be exposed to fluid injection. The condition of steam entering the reservoir is considered to fall within the following limits: (1) steam pressures less than 1,000 psig, (2) steam temperatures between 300 and 700F and (3) steam quality less than 90 percent. The last restriction is due to equipment limitations. Normally, injection re maintained for less than 3 weeks. After termination of injection, the condensation stage begins. The well is shut in for several days, supposedly to make certain that the injected steam condenses. This condensation would insure the retention of injected heat. The production stage is initiated when the well is opened again. Reservoir response during this stage determines the effectiveness of the process (response is defined as the oil production rates, the water production rates and the wellbore temperatures observed during the entire production stage). The immediate response of the reservoir is sometimes quite good. Sets of case histories by Longl and by Owens and Suter2 give some typical figures for response. Duration of the production stage is equal to the time needed for the oil production rate to decline to some predetermined value. This usually requires 4 to 6 months. Termination of the production stage coincides with the start of the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable to continue. One simple model2 and two more sophisticated models3,4 of the process have been presented. These are based on fundamentally different assumptions than those used in this investigation. Although the three models might be modified to fit the assumptions used in this study, it is felt that greater rigor would result by developing a

By R. DiBella, H. Biloni, G. F. Bolling

A study of the detailed relationship between solidification substructure and microsegregation in dilute tin alloys has been continued. New observations reveal that depressions form at the solid-liquid interface not only as an initial form of segregation but throughout the range of increasing constitutional supercooling. In order to show the importance of this node formation it proves convenient to make two simplifications. Although substructure changes continuously as constitutional- supercooling increases,&apos; the following discrete stages may be used for discussion: 1) the planar solid-liquid interface; 2) ordered nodes, or depressions at the interface;&apos; 3) two-dimensional or elongated cells;3 4) regular or hexagonal cells;4 5) distorted cells, or hexagonal cells with branches;4 6) dendrites. It is also convenient to ignore observations made near grain boundaries which interact with the cellular substructure.2-4 And, it should be clearly pointed out that all singular depressions at the solid-liquid interface will be called nodes. Heretofore, the term "node" has been used without clear justification to describe both the truly isolated depression and the junction of cell walls appearing in a later stage of segregation. This usage is continued because it seems proved by the observations. Standard systematic growth of tin crystals was undertaken over a broad range of constitutional supercooling using various added solutes. Except for one or two chance observations, this research failed to reveal any appreciable range of growth conditions over which a disordered array of isolated nodes exists. Even though &apos;some finite range of random instability must exist, it is now concluded that stage one passes very rapidly to stage two. Next, after confirming that stage two passes to stage three by the elongation of isolated nodes: a reexamina-tion of stages three, four, and five followed. Standard metallography showed that pockets of higher solute concentration (for ko < 1) became more numerous in cell walls the more severe the growth conditions. These high-concentration regions must arise from depressions; however, in stage three their segregation is not distinguishable from the segregation of the nodes which join cell walls together. It seems, therefore, that the presence of nodes is causal in the formation of new cell walls, and that the mechanism by which stage three passes to stage four is initiated by nodes. If a similar reasoning is followed, the separation of stage four from stage five appears to be just a convenience that has arisen from the decanted interface observations made in the past. The present observations again show that more severe growth conditions relate directly to an increase in the number of nodes in the hexagonal cell walls. These nodes apparently serve as the origin for lines of segregation extending within the body of a cell, and can thus be assumed to represent the earliest form of branching,* as shown here in Fig. 1. The examination of stage six involved decanted-interface structures as in Fig. 2, which are similar to those considered by Rutter and Chalmers,5 Plaskett and winegard,6 and Hellawell and Herbert,7 and where distinct protrusions are each surrounded by a depressed boundary. The corresponding microsegregation behind the interface, but not far enough behind to allow a smearing of the segregation because of diffusion,4 is shown in Fig. 3. Both the shape of the decanted interface and the segregation pattern behind it

Jan 1, 1968

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"&apos; is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By F. W. Warnaars

The Los Bronces copper deposit is located on the west side of the Andes Mountains in central Chile about 54 km (34 miles) northeast of Santiago. The deposit consists of a hydrothermal breccia complex that was emplaced in the western part of an earlier porphyry copper mineral system. This system exhibits propylitic, sericitic, silicic to potassic hydrothermal alteration with disseminated and stockwork copper-molybdenum sulfide mineralization over an area of about 12 km2 (5 sq. miles). The Rio Blanco Mine, about 800 m (0.5 miles) east of Los Bronces, is an underground block caving mine located in the central part of this system. The mineralization at Rio Blanco is characterized by one of the highest primary copper grades known for porphyry copper systems. Present mining at Los Bronces is from an open pit located in the northern part of a hydrothermal complex that is composed of at least seven different copper-bearing tourmaline breccia pipes. Together these pipe form one large contiguous body about 2 km (1.2 miles) long and 0.7 km (0.4 miles) wide at the surface. This body crops out at elevations of between 3.5 and 4.1 km (2 and 2.5 miles) above sea level. Each breccia pipe has a characteristic shape, matrix, type and degree of mineralization and alteration. Quartz, tourmaline, specularite, anhydrite, pyrite, chalcopyrite, sericite, chlorite, and rock flour are present in significant quantities in most breccia matrices. The clasts consist mainly of quartz monzonite, andesite, and minor amounts of quartz latite porphyry. The seven different breccia pipes are identified, from oldest to youngest, as Ghost, Central, Western, Infiernillo, Fine Gray, Anhydrite, and Donoso. The breccias coalesce, interfinger, or display gradational contacts. In places they form sharp contacts with each other and with the surrounding intrusive or volcanic host rocks. Early breccias are disrupted or cut by subsequent breccia events. Explosive emplacement was followed by collapse after the release of hydrothermal pressures. The Los Bronces breccia complex has sharp contacts with the surrounding intrusive stock and andesites. These contacts dip inward on the north, west, and south margins. The eastern contact is nearly vertical and/or dips slightly outward and suggests a westward tilting of the body of about 15° after emplacement. The breccia complex is not fully explored at depth, but is known to extend at least below the 3 km (2 mile) elevation in its central eastern part, about 1 km (0.6 miles) below the highest breccia outcrop. Primary copper sulfide minerals are most abundant in the Donoso and Infiernillo breccias where the matrix consists mostly of tourmaline, quartz, sulfides, specularite, and/or chlorite with minor amounts of rock flour, sericite, and clay. The volume of the matrix material is mostly smaller than in the other breccias. Secondary enrichment enhanced the primary copper grade in the southern two-thirds of the Los Bronces breccia complex and in much of the surrounding porphyry system. Primary grades of 0.3% to 0.5% copper have been enriched to approximately 0.9%. This enrichment may extend from surface outcrops to a depth of more than 500 m (1, 640 ft) in more permeable parts of the breccia complex. A leached and oxidized capping of variable thickness covers a large part of the enriched layer and exceeds 300 m (984 ft) at one location. The shape and depth of the enrichment blanket and the capping suggest that the enrichment process is still active.

Jan 1, 1983

By E. C. W. Perryman

On electropolishing, high-purity Cu-Sn and Cu-Sn-P alloys with more than 5 to 9 pct Sn were found to contain many grain boundaries with a ridge-and-furrow profile. The effect was not eliminated by solution treatment and was present at the new boundaries in recrystallized material. It could be produced by diffusing tin into the 3 pct Sn alloy and it is concluded that the effect is due to enrichment of certain boundaries in tin, or possibly in an impurity present in the tin, in solid solution. IN the hot working of tin bronzes, especially those with moderately high tin contents, considerable difficulty is frequently encountered from intercrystal-line weakness, which results in cracking at the edges in sheet on strip rolling and in the unsupported regions of the rod in rod rolling.&apos; These difficulties are not at all pronounced with up to 3 pct Sn, but at 5 pct Sn impose serious limitations and at higher tin contents, especially if the phosphorus content is also high, they may become very severe. In some work carried out at the laboratories of The British Non-Ferrous Metals Research Association it was found that a notable lack of ductility in tension at elevated temperatures, associated with intercrystal-line failure, was characteristic of tin bronzes even of relatively high purity. That the intercrystalline fracture is not due to a brittle or molten impurity phase at the grain boundaries was shown by the fact that the temperature at which intercrystalline fracture first occurred decreased with decrease of rate of straining. Tensile tests on some commercial tin bronzes, reported by Goetzel,² show a similar fall in ductility with increasing temperature. As no visual evidence had been obtained showing that the grain boundaries of the tin bronzes were different from those in copper, a more detailed microscopical examination was carried out, and the results of this are given in the present report. Several workers"&apos; have observed that electrolytic polishing is a powerful tool for detecting small amounts of a second phase and in particular for detecting high solute concentrations, "equilibrium segregation," at grain boundaries. Since it had been found that the suggested solutions for electropolishing bronze and the standard solutions for brass and copper did not give satisfactory results it was first necessary to find a suitable electropolishing solution.&apos; Experimental Procedure Materials Used: The cast and wrought materials used for this work were the same as those used for the mechanical tests referred to above. They comprised 3, 6, and 9 pct Sn alloys without phosphorus and the same three basic alloys with 0.03 and 0.4 pct P. A 5 pct Sn alloy without phosphorus, of similar purity, was also examined. The basis materials were Chempur tin, high purity 15 pct phosphor-copper and cathode copper, and spectrographic analyses are given in Table I. Treatment: The cathode copper was first melted under charcoal, degassed by plunging marble chips beneath the surface, and cast through a coal gas flame into sand molds to produce a number of small ingots which after machining were of a suitable size for subsequent vacuum melting. Chill cast bars of the alloys, approximately 1¼ in. in diameter, were then made by melting and casting in vacuo, the tern-

Jan 1, 1954

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"&apos; and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

* The greatest and richest iron ore body in the world was discovered by U. S. Steel in Venezuela in April 1947, and is disclosed for the first time in this issue (p. 178), One solid mountain of ore, Cerro Bolivar, will furnish more tonnage than the famous Hull Rust pit at Superior has, or can produce. Total resources are on the order of 2 billion tons plus. Big Steel is now moving with great speed on construction to bring out this ore, and 10 million tons are scheduled for shipment into Baltimore and Birmingham by late 1952. This ore will arrive at, Pittsburgh at a price lower than present natural ores from Superior. The Venezuelan properties will be completely mechanized. •U. S. Steel and independent companies are embarking on a taconite beneficiation program of tremendous proportions, which must be speeded to completion in the 1950&apos;s (see p. 185). By 1960 over $l.2 billion dollars will be spent on Venezuela, taconite, and Labrador to solve the United States iron ore crisis. In addition, U. S. Steel will spend another $300 million plus for a new steel mill at Trenton, N. J., before 1955. •The Deister Concentrator Co. gave $500 to the 1950 Coal Division Scholarship Fund. •Howard N. Eavenson, in analyzing the bituminous coal situation (see p. 193), suggests that anti-trust laws be extended to labor unions, disinterested trustees to administer pension funds, begin pension funds now and stop the collection of all "check-offs" for union dues or funds. •Minerals and metals worth 13.9 million dollars were produced in the United States in 1949, Secretary of the Interior Oscar L. Chapman announced. Although this value was 11 pct less than in 1948, it was the second greatest in history. Nonmetallics was the only major group that in 1949 equaled the 1948 production high. Mineral fuels decreased 12 pct and metals 15 pct. • Prospects for making gas from coal are seen to be unattractive by the Pittsburgh Consolidated Coal Co. because the success of operation depends on price and supply of coal which presently are not attractive. The company has shut down its gasification plant at Library, Pa. * Economic prospects for the immediate future in the United States are good and business probably will continue at its present high levels throughout at least the early part of 1950, Secretary of Commerce Charles Sawyer said in his year-end report to the White House based on his personal survey of business conditions. •A 467-ft well 34 miles north of Rock Springs, Southwestern Wyoming, is said to be flowing a 5 pct solution of nearly pure trona (sodium carbonate) at the rate of 10,000 barrels a day. Trona, natural soda ash, is mined for the chemical trade at Searles Lake, Calif., and from about 1500 ft underground near Green River, Wyo., and has been in short supply. •The AEC is "very much interested" in a discovery of radioactive material that has been made in Baraga County bordering Lake Superior in the Upper Peninsula of Michigan, reported F. G. Pardee, Michigan State mining engineer. The material has been identified as uranium oxide in the form of pitchblende or uraninite. The discovery, made by a geologist of the Jones & Laughlin Ore Co., is the only instance in which the commission has certified samples of Michigan rock.

Jan 2, 1950

By J. A. B. Forster

W. G. WOOLF*—The paper has a wealth of data that take careful, detailed study. As has been indicated the highlights can be only touched in the paper. The design and the arrangement of the rabble teeth as well as some of the other details of operation show a very careful study and a scientific approach to the problem which in most plants using hearth roasters are matters of trial and error with empirical conclusions and, perhaps too often, just arbitrary supervisory preferences which may be erroneous. Here the problem has been approached from a scientific angle which think well merits careful study. The ability to treat the tonnages they get through these furnaces think is made easier by reason of the high sulphide sulphur in the resulting calcines which the balance of the plant—the leaching and so on—can cope with. As indicated by Mr. Weldon in his dis- cussion earlier this morning, in most zinc plants an attempt is made to have as low a sulphide sulphur content in the roaster calcine as possible. But in the operation of the Risdon plants, they are able to cope with sulphide sulphur content up to 5 pct which is far beyond the amount of sulphide sulphur that can be handled elsewhere. I think the autogenous roasting is made easier because driving out the last percentages of sulphide sulphur brings on the necessity for extraneous heat, and that is further exemplified because even at Risdon the author shows the desirability of using some oil to better the operation, particularly for uniformity of roasting results and to obtain more regularity of furnace operation. A. A. CENTER*—Regarding the hard crusts in the beds of the furnace and autogenous roasting, the paper speaks of the former being due, at least to a considerable extent, to lead sulphide in the crusts. I wonder if the author has considered the hard crusts as being due in large part to zinc sulphate. While I was developing large zinc operations we ran into hard crusts which had to be dug up. I took several lumps which were so hard they showed the marks of the rabble teeth very plainly and kept them in my office for some weeks. A visitor came along one day, and as he was having similar troubles, I told him what we were doing about ours. I started to pick up one of these lumps and to my amazement the thing crumbled in my hands whereas originally it had been so hard it wore the rabbles down very rapidly in the furnace. I sent the sample to the laboratory and found that it analyzed very high in water-soluble zinc and sulphate-sulphur. The crumbling of the lumps was evidently due to the anhydrous zinc sulphate gradually taking on moisture from the air and forming crystalline zinc sulphate seven parts water. The increase in volume would, of course, result in disintegration of the lumps. As to getting a high tonnage in the autogenous roast, that is partly because of finishing at about 5 pct sulphide sulphur. It is a real job to get down to, say, ½ pct sulphide sulphur, which is what is usually desired, and still put through a good tonnage.

Jan 1, 1950

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.&apos; Of direct bearing on the work to be reported here are the comments of Jetter&apos; in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1&apos;3&apos;4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By S. R. B. Cooke, W. Philippoff, Donald E. Cadwell

[THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle ? is determined only by the reagent&apos; and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox2 showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0° to the equilibrium value of 60°. Further, Gaudin and Vincent&apos; showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, ? varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher4 were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by, the difference of the free surface energies (surface tensions) of the respective phases ?1 and ? 2 before contact and the interfacial free surface energy ?12 after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation5 of W from the surface tension of the liquid ? and the contact angle ?: [W = y (1 + cos ?)[1]] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are ? and ?3. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: [W,,,=x•W2+ (1-x).WR[2] .] in which Wm is the work of adhesion of the composite surface. Eq 1 can be introduced into W2 and W3 but in the case of Wm some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle ?m, calculated from Wm, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that ?m would have aphysical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically]

Jan 1, 1952

By M. P. E. Desvaux, P. Charsley

OLIP-line observations on copper alloys, using the electron microscope, have been made by a number of workers,13 but this work has been confined to a brass. In a CuAl alloys Koppenaal4 and Koppenaal and Fine5 have made observations with the optical microscope and by the use of interferometry. They found that the observed slip step heights inside the Liiders bands accounted for only 42 pet of the total macroscopic strain. The suggestion was put forward that optically unresolvable slip in other parts of the specimen accounted for a major part of the macroscopic strain. This is surprising since it is known from other workers that slip in a brass is inhomogeneous; i.e., large amounts of slip occur on individual {lll) closelys paced than being shared by a large number of closely spaced planes. Furthermore, a brass and a CuAl alloys with high concentration of aluminum exhibit similar deformation characteristics and slip-line patterns. Prior to investigations into the behavior of copper and a CuAl alloys under reversed stresses in tension and compression, some preliminary experiments have yielded results which the authors think resolve this discrepancy, and throw some further light on the behavior of a CuAl in tension. An experiment was carried out on a 10 at. pet CuAl single crystal, of gage length 7.5 cm, diameter 3.1 mm, and orientation shown in Fig. 3 (inset), for the purpose of resolving the above discrepancy. The specimen gage length was electropolished for 10 min in a 50:50 orthophosphoric acid (SG=1.75)-distilled water system, with 2 v across the cell and a current density of 0.5 amp per sq cm. The cathode was made of copper. After a tensile strain of 0.067 ± 0.001, intense slip was observed over a length 2 cm of the gage length whilst the rest of the specimen was relatively undeformed. In the lightly deformed region, slip bands of mean width 20 /x were spaced about 1 mm apart on average. The transition from the heavily slipped region (usually called a Liiders band) to the lightly deformed region was gradual, the slip-band density increasing as the "Liiders band" was approached. In the latter, the slip bands became so close together that, to the naked eye, the specimen appeared to be continously slipped, and the typical microtopography of this region is shown in Fig. 1. Twelve electron micrographs were taken at random from replicas of the Liiders-band region, and the widths of the slip lines were measured. The slip lines account for an over-all tensile deformation of 7.0 ± 0.7 pet, after allowing for the lengths of the un-slipped regions, which is in good agreement with the macroscopic strain. The distribution of slip-line widths was also measured and is shown in Fig. 3. Since Koppenaal could not resolve slip lines with height less than 540A (limit of resolution represented by dashed line), then it was deduced that he could have measured only about 50 pet of the deformation within the &apos;Liiders Band&apos;. It is concluded, contrary to the suggestion of Koppenaal,5 that virtually all the macroscopic strain is accommodated within the "Luders band" and that there is no need to invoke fine slip distributed uniformly over the gage length.

Jan 1, 1967

By O. P. Quist, S. H. Carpenter

The internal friction of single-crystal LiF has been investigated as a function of crystal orientation, while simultaneously applying a static compressive load. Three different crystal orientations were used, these being samples with the (100), (110), and (111) directions along the sample length. Results show the internal friction measured to be similar in appearance but different in magnitude for the (100) and (110) samples. With both orientations, application of a static stress caused an increase in the amplitude-independent damping, which recovered with time. The amplitude-dependent damping was found to first decrease with load up to the yield stress and then increase rapidly. Samples of the (111) orientation were found to have no measurable internal friction even when loaded up to 3.0 kg per sq mm. These results are discussed in terms of current theories of internal friction in ionic crystals. This paper presents the results of an investigation of the dislocation mobility and dislocation motion in high-purity single-crystal LiF at applied stress levels up to the yield stress. Internal friction measurements of the dislocation damping while simultaneously applying a static compressive load was the experimental technique used. LiF crystals much prefer to slip on the (110) set of slip planes. However, with a suitable stress distribution they can be forced to slip on the {100} set of slip planes.&apos; For both sets of slip planes the slip direction is the same, namely (110). The object of this investigation was to try and learn more about the dynamical properties of dislocations on the different slip systems in LiF crystals. EXPERIMENTAL PROCEDURE Dislocation damping was measured, in terms of the log decrement, using a five-component marx2 composite piezoelectric oscillator. The apparatus used allows one to measure the dislocation damping while simultaneously applying a static compressive load on the sample. A schematic of the apparatus used is shown in Fig. 1 and a complete discussion of its construction and operation is given elsewhere.3 All measurements were made at room temperature with a longitudinal resonant frequency of approximately 50 kc per sec. Damping measurements were made using longitudinal vibrations with strain amplitudes from up to 10. Static loads up to 3.0 kg per sq mm were applied to the sample while the damping was being measured. Samples used in this investigation were high-purity single crystals of LiF purchased from the Harshaw Chemical Co. All samples were approximately of an in. square and were hand-ground in length to one-half wavelength to match the resonant frequency of the driver and gage quartz crystals. Samples of three different crystallographic orientations were used, namely, crystals with the (loo), (110), and (111) direction parallel to their length. The magnitude of the damping is a direct measure of the area on the slip planes swept out by dislocations during a complete oscillatory cycle. With a sample of the (100) orientation the maximum applied shear stress, due to longitudinal vibrations, is on the (110) slip planes with zero shear stress on the (100) slip planes. Thus, damping measured from a (100) sample is due entirely to dislocation motion taking place on the (110) set of slip planes. Similarly, for a sample of the (111) orientation there is zero shear stress on the (110) set of slip planes and the damping measured from a sample of this orientation is due entirely to dislocation motion on the (100) set of slip planes. Samples of the (110) orientation will have a component of shear stress on both sets of slip planes and

Jan 1, 1969

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau&apos;s War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944