Search Documents

. F. W. SPERR, JR.,* Pittsburgh, Pa.--Mr. Malcolmson states that the Carbocoal process produces ammonium sulfate in excess of that normally recovered in the ordinary byproduct coke process. Table 3 indicates that 20,000 to 25,000 lb. of sulfate of ammonia are obtained in carbonizing 1000 tons of Clinchfield coal. This is a high-grade coal and yields from 26 to 28 lb. of ammonium sulfate per ton in a modern byproduct coke oven. On the next page, 21 lb. is stated as the yield of ammonium sulfate per short ton of raw coal; this is less than the average production from any well operated byproduct coke-oven plant treating coal of the character usually coked, in Pennsylvania and Ohio. The statement as to the comparative yields of light oil is somewhat misleading in view of the results obtained during the past year or two by the more modern byproduct coke plants. The plants put in operation by the H. Koppers Co., during the past two years, are producing about 3.5 gal. of light oil per short ton of coal, and several of these plants are producing more than 4 gal. per ton. The yield of pure toluene runs from 0.45 gal. to 0.55 gal. per ton. .The quality of the light oil .obtained from the Carbocoal process is of much greater importance than would be inferred by one not closely familiar with the subject. The presence of paraffins in the benzol and toluol fractions seriously detracts from their commercial value; the benzol and toluol fractions derived fro in the Carbocoal process contain about 50 per cent, of paraffins. It should be thoroughly understood what these paraffins are. They are simply hydrocarbons that go to make up ordinary petroleum, and if a successful method for the removal of paraffins from benzol and toluol has been developed, this can at once be applied to several well known processes by which benzol and toluol can be made directly from petroleum, which have as yet been total failures on account of the contamination of these products by paraffins.

Jan 11, 1918

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By V. R. Garfias

Principal events in petroleum operations of Mexico during 1934 have been the completion of three producing wells in the Poza Rica area and the plans for the expansion of operations of the Cia. de Petroleos de Mexico, S.A. (Petromex). Production for 1934 is estimated at close to 38,000,000 bbl., an increase of 4,000,000 bbl. over the previous year; an increase due in large part to the successful development in Poza Rica. The output of the South fields (Golden Lane) and Tehuantepec fields also increased somewhat during the year. Production of natural gasoline increased from 382,000 to 431,000 bbl. in 1934. Crude run in local refineries is estimated at 26,000,000bbl., some4,000,000bbl. more than the previous year. Exclusive of bunker fuel exports totaled 24,000,000 bbl., or 3,000,000 more than in 1933. Domestic consumption increased approximately 500,000,bbl. during the year, reaching a total of close to 13,600,000 bbl., exclusive of ships' bunkers. A total of 148 wells were completed as compared to 91 in 1933 and 40 in 1932. In proven areas, 133 completions resulted in 54 producers and 79 failures. The 15 wildcats drilled during 1934 gave no encouraging results. Seven of these were located in the border zone of northeastern Mexico; three tested possible northeast extensions of the Northern fields; two were drilled for possible extensions of the "Golden Lane" and three were completed in the Isthmus of Tehuantepec. Fields Northern Fields (Heavy Oil District).—There were 34 producing wells and 71 failures completed in the Northern fields, as compared to 20 producers and 20 failures in 1933. Practically all new producers were drilled to the shallower San Felipe formation, while wells drilled to the deeper Tamasopo limestone encountered salt water. Production of the field totaled 11,890,000 bbl., a decrease of 7.5 per cent from the previous year. Acid treatment was attempted during the year in seven wells

Jan 1, 1935

By T. Suzuki

LABOR. conditions have finally caused rock-drilling machines to supplant hand drillers in the Japanese mining industry, and have encouraged this study. During a period of three years 25,000 tests were made on 67 different American, Japanese, and European rock drills, using, respectively, the Paynter testing machine, and drilling in granite and limestone. Recorded were: air consumption, speed of rotation, torque of rotation, foot-pounds of striking energy, air pressures, input horsepowers, and speed of rock penetration. The author expresses his views on the interrelation of these factors and offers theoretical support, as well, by formulas based upon the mechanics of impact. He discusses the different designs of the valves, cylinders, piston hammers and rotation devices involved in the different types of rock drills, with respect to their merits and defects and offers conclusions about the factors that should be considered in the new design of a superior rock drill. The author's mathematical demonstrations and arguments for a value of "best feed clearance" of the drill bit from the rock are based upon the hand-operated screw-fed type of hammer drill. Automatic feeds have not been considered in this paper except for the tests on one drifter with air feed, 10 air-feed stopers, and some hand-held blockholers. The following classes of drills, with one of each model, size, or type, were tested: 23 heavy drifters, 34 light drifters and hand-held drills, and 10 stopers. They represented the following makes and models: 40 from the United States—namely, Ingersoll-Rand 18, 148, L-74, 24-70, N-72, N-75, R-72, 26, BAR-33, BCR-430, DCRW-23, RA-12, CA-31, CC-11; Denver 7, 107, WT-21, WT-31, WT-331, WT-337 (models WT with motor rotation, screw feed), 11, Waugh 93, 95; Waugh 16; Sullivan DR-6, DW-64, T-3; DP-321, DP-331; DA-21, DT-44, DT-421; Gilman AX-321 (motor rotation and air feed); Cleveland D-5; AIBQ, 44-SWR,

Jan 1, 1940

By T. Suzuki

LABOR. conditions have finally caused rock-drilling machines to supplant hand drillers in the Japanese mining industry, and have encouraged this study. During a period of three years 25,000 tests were made on 67 different American, Japanese, and European rock drills, using, respectively, the Paynter testing machine, and drilling in granite and limestone. Recorded were: air consumption, speed of rotation, torque of rotation, foot-pounds of striking energy, air pressures, input horsepowers, and speed of rock penetration. The author expresses his views on the interrelation of these factors and offers theoretical support, as well, by formulas based upon the mechanics of impact. He discusses the different designs of the valves, cylinders, piston hammers and rotation devices involved in the different types of rock drills, with respect to their merits and defects and offers conclusions about the factors that should be considered in the new design of a superior rock drill. The author's mathematical demonstrations and arguments for a value of "best feed clearance" of the drill bit from the rock are based upon the hand-operated screw-fed type of hammer drill. Automatic feeds have not been considered in this paper except for the tests on one drifter with air feed, 10 air-feed stopers, and some hand-held blockholers. The following classes of drills, with one of each model, size, or type, were tested: 23 heavy drifters, 34 light drifters and hand-held drills, and 10 stopers. They represented the following makes and models: 40 from the United States—namely, Ingersoll-Rand 18, 148, L-74, 24-70, N-72, N-75, R-72, 26, BAR-33, BCR-430, DCRW-23, RA-12, CA-31, CC-11; Denver 7, 107, WT-21, WT-31, WT-331, WT-337 (models WT with motor rotation, screw feed), 11, Waugh 93, 95; Waugh 16; Sullivan DR-6, DW-64, T-3; DP-321, DP-331; DA-21, DT-44, DT-421; Gilman AX-321 (motor rotation and air feed); Cleveland D-5; AIBQ, 44-SWR,

Jan 1, 1940

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By J. R. Thoenen

IN five years mineral wool has grown to a thirty-million-dollar industry from one whose output was valued, in 1933, at $1,700,000. Ten years ago, in 1928, there were only seven producing companies, with an annual output of but 50,000 tons. By 1936 fifty or more companies were producing half a million tons. The industry is still growing vigorously and will profit from the expected activity in building in 1339, for two-thirds of this material is used for building insulation and to assist in fire-retarding, in both new and old homes. It is as useful in the South, to protect against heat, as in the North, to keep out the cold, if one may speak nontechnically. It is a concomitant of air conditioning, that new addition to the American standard of living that began in theatres, department stores, and railroad dining cars, and is rapidly progressing down to small homes. Here, then, is an industry that is only beginning to have a present, and one with an almost certain important future; one that depends upon mining and the by-products of mining for all of its raw materials; one that every progressive mining man should know something about.

Jan 1, 1939

By A. Lucian Walker

SILVER is not only of paramount importance to millions of people as a medium of savings and to other millions as a medium of exchange, but it is also valuable and useful in industry. Mexico continues to be the largest producer of this metal, followed by the United States, Canada, and Peru. The largest consumers are China and India, which normally absorb about two-thirds of the world's mine production, hoarding it as savings. The imports by these countries exert a powerful influence upon the price, yet neither country is on the silver standard. China having abandoned it in 1935 and India in 1893, when the rupee was definitely linked to the pound sterling. Other nations such as Persia, Ethiopia, Mexico, and many of the South American countries either have been on the silver standard or have used silver as their chief circulating medium, and most large nations use it for subsidiary coins, this use accounting for 20 to 30 million ounces annually. The arts and industries have consumed 35 to 40 million ounces each year.

Jan 1, 1937

The following is a partial list of members and guests who called at Institute headquarters during the period Sept. 10, 1917, to Oct. 10,1917. Thomas J. Adams, Rahway, N. J. Leon Root Long, Tirapata, Peru, So. Am. L. W. Bahney, Waterbury, Conn. F. M. McClenahan, Ben Avon, Pa. D. W. Brunton, Denver, Colo. E. Francis McCrossin, Birmingham, Ala. J. R. Buchanan, Pasadena, Cal. P. S. Moses, Savannah, Ga. R. C. Canby, Wallingford, Conn. William A. Nelson, Cartersville, Ga. Paul R. Cook, Zaruma, Ecuador. Edmund Newton, Minneapolis, Minn. F. Crabtree, Pittsburgh, Pa. Askin M. Nicholas, Porrington, N. S. W., J. T. K. Crossfield, Chuquicamata Chile. Australia. Wayne Darlington, Georgetown, S. C. E. G. Norton, Chicago, Ill. R. W. Deacon, Elizabeth, N. J. M. L. O'Neale, Coal City, .Ala. Alexander Deussen, Houston, Tex. W. E. Pomeroy, El Paso, Tex. G. G. Dobbs, Bessemer, Ala. Joseph P. Ruth, Denver, Colo. E. B. Durham, Canonsburg, Pa. Gustavus Sessinghaus, Denver, Colo. L. H. Duschak, Berkeley, Cal. A. L. Sweetser, Boston, Mass. F. A. Fahrenwald, Cleveland O. G. M. Taylor, Colorado Springs, Colo. A. H. Fay, Washington, D. a. Allan G. Waite, Dragoon, Ariz. C. L. French, Brooklyn, N. Y. H. Vincent Wallace, Los Angeles, Cal. Carlos F. Galan, Riverside, Mex. H. A. Wentworth, Boston, Mass. Herman Garlichs, St. Louis, Mo. Alfred W. G. Wilson, Ottawa, Canada. Ernest Klepetko, Anaconda, Mont. Samuel S. Wyer, Columbus, O. D. A. Lyon, Washington, D. C. M. M. Albertson has accepted a position with the McIntyre-Porcupine Gold Mines, Ltd., Schumacher, Out., Canada. James A. Block is now employed by the Ray Consolidated Copper Co., of Hayden, Ariz.

Jan 11, 1917

By H. E. Montgomery

Engineering trends for some years have been toward higher temperatures, both in process work and in steam generation. Progress in design has been dependent upon the development and evaluation of suitable alloys. Elementary knowledge of the limitations of copper-base alloys indicate their unsuitability for the higher ranges of operating temperatures; say, for steam to 950°F. Emphasis upon the more severe conditions perhaps is a reason why more complete evaluations have not been made for copper-base alloys over their range of suitability. However, the few studies made show clearly the need for more accurate evaluations. Some copper-base alloys long looked upon favorably because of superior room-temperature properties are not as desirable as some others perhaps not so "strong" and "hard," as measured by usual acceptance tests. Load-carrying capacity and structural stability arc two important factors. Structural stability as influenced by temperature, by presence of corrosive media, or by the effects of stress itself, frequently is a limiting factor. An early reference to creep properties of the cast copper-base alloys is that of Brown1 (Admiralty gun metal, Cu 87.5, Sn 10.1, Zn 2.3 and Pb 0.08). His tests were similar to present-day stress-rupture tests without measurement of creep elongrttion. Loading was in steps with usually 24 hr. between steps, and continued until failure. He advocated a "useful strength value" of 61/2 tons (I4,560 Ib.) per sq. in. at 572°F. (300°C.). A specimen broken in 1/2 hr. at 572°F. had a strength of 21 tons (26,880 Ib.) per sq. in. The strength values as determined by 1/2-hr. tests and those by the longer stress-rupturc start to differentiate at 392°F. (200°C). This is the temperature at which time at load began to play an important part. Bolton, Price and Hebemann2 give creep curves on 88-10-2 (A.S.T.M. B-60, CU 88, Sn 10, Zn 2) and steam or valve bronze (A.S.T.M. B-6I, Cu 87.50, Sn 6.00, Zn 3.75, Pb 1.70) at 500°F. Direct comparison of the two alloys under 7500 lb. per sq. in. stress showed the steam bronze (A.S.T.M. B-61) superior in creep strength to the 88-10-2 (A.S.T.M. B-60). The steam bronze shows no creep after 700 hr. (1540-hr. test). The 88-10-2 shows a rate of about 7.0 per cent in 100,000 hr. over the last 700 hr. of the test. Creep curves on the steam bronze are also given at the same temperature (500°F.) with loads of 6500 lb. per sq. in. and 8000 lb. per sq. in. These indicate "creep strengths" (creep rate within I per cent in 100,000 hr.) in excess of 8000 lb. per sq, in. for this alloy. It was found that higher percentages of tin are detrimental to creep resistance. This is caused by the presence of or formation during test of considerable alpha-delta eutectoid in the higher tin alloys. Bolton also states that the high

Jan 1, 1945

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By G. Bhat, J. F. Libsch

A STUDY of the kinetics of embrittlement in engineering alloy steels during tempering has indicated that the presence of alloying elements may define two distinct regions of embrittlement: 1) at 800° to 1000 °F, termed low temperature embrittle-ment, and 2) in the temperature range 1150 ° to 1250°F, termed high temperature embrittlement.13 It has been suggested that embrittlement in each region may be due to a different mechanism. At intermediate temperatures and extended times the course of embrittlement may be influenced by the superposition of the embrittlement occurring in the two regions. Furthermore, low temperature embrittlement has been known to decrease as the temperature is raised slightly above the maximum embrittlement range.' Jaffe and BuffumV ave presented data for a Ni-Cr steel illustrating the removal of the em-brittlement occurring at 932°F by reheating to 1250°F for an hour. Their data further shows that embrittlement proceeds continuously with increased time at 1250°F, becoming pronounced at long times. They interpreted this behavior as a retrogression phenomenon involving the solution of the small nuclei of precipitate formed at 932°F as the temperature was increased, and reprecipitation of larger nuclei stable at 1250°F, with the reoccurrence of embrittlement. It appears desirable to reconsider this explanation in the light of the two regions of embrittlement proposed by the authors1 for some alloy steels. In addition, it appears desirable to determine any influence of a preconditioning treatment in each temperature range upon subsequent development of low and high temperature embrittlement. It is thus the object of this investigation to study the characteristics of the two modes of embrittlement proposed in a commercial Ni-Cr alloy steel (AISI 3140). Experimental Details Material—The material used in this investigation was commercial AISI 3140 steel bar stock, received as % in. hot-rolled rounds. The steel analysis was as follows (in percentages): C, 0.39; Mn, 0.79; Si, 0.30; S, 0.028; P, 0.015; Ni, 1.26; and Cr, 0.77. Material Processing and Heat Treatment—The bar stock was first ground to 0.430 in. squares and cut into specimens 23/4 in. long. These specimens were austenitized at 1650°F for 1 hr and oil

Jan 1, 1958

but, returning to South Africa, for the next two years he was assistant general manager of the Simmer Deep Gold Mining Co., at Johannesburg. In June, 1911, he returned to New Zealand as general manager and consulting engineer for the Consolidated Goldfields of New Zealand, at Reefton, which position he held at the time of his admission to the Institute in 1914. Early in September, 1915, he left New Zealand for active service in France. Corporal Sheppard B. Gordy Sheppard B. Gordy, born in Ansonia, Conn., in 1889, graduated from the Sheffield Scientific School in 1910 and with the degree of E. M. in 1912. He entered the employ of the Braden Copper Co. immediately on his graduation and remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time he had gone to Dayton, Ohio, to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9. Lieutenant Thomas Clarence Gorman Thomas C. Gorman, a lieutenant in the Second Tunnelling Company of the Canadian Engineers, was killed in France on Mar. 18, 1918. He was resting in his sleeping hut and was in the act of writing a letter when a bursting shell killed him.

Jan 1, 1920

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

C. Q. Payne, New York City: Prof. Blake's inference that magnetic separation may be successfully employed upon smithsonite and iron oxide, after a preliminary roasting, is confirmed by the fact that this separation has been carried on with entire success for over a year at the works of the Wythe Lead and Zinc Mine Co., Austinville, Va. The ore mined on this property is a mixture consisting chiefly of galenite, smithsonite and limonite. The crude material is crushed, screened and washed in log washers for the removal of clay, and then jigged for the separation of the galenite. The zinc-and iron-ores are then roasted in reverberatory furnaces, being turned and moved towards the bridge-end of the hearth by manual labor. The roasted material contains from 20 to 26 per cent. of metallic iron. The slight difference in the specific gravities and the friable condition of the ores after roasting prevent the separation of the oxides by means of jigging. It was therefore the practice, previous to the use of magnetic separation, to charge the roasted material directly into the retorts of the zinc-furnaces. The rapid cutting of the retorts under this practice proved a serious inconvenience and expense. In the spring of 1892, the writer built for the Wythe Lead and Zino Mine Co. a magnetic separator which embodied several novel features and which was designed to treat the roasted zinc- and ironoxides. This separator has proved entirely successful for the purpose for which it was designed. During the first nine months of its operation, 1415 tons of 2240 pounds of roasted material were passed through the separator, producing about 675 tons of heads carrying from 50 to 55 per cent, of metallic iron, which are sold to a neighboring blast-furnace. The tailings, which contain the zinc, carry from 4 to 6 per cent. of metallic iron. For magnetizing the iron-ore previous to separating it from the zinc-ore, no change whatever mas made in the form of the reverberatory furnace previously employed. It was found that, by charging near the bridge-end of the hearth, toward the end of the roast-

Jan 1, 1894

By M. W. BERNEWITZ

AUSTRALIANS and New Zealanders, whose countries have respectively yielded gold to the value of £666,000,000 and £96,000,000, are taking full advantage of the current high prices for that metal. There is a marked activity in ordinary prospecting, geophysical exploration, further development of working mines and reopening of old properties, formation of new companies, installation of new equipment and processes, and expansion of operations generally. Australian gold production last year was approximately double the quantity of 1929 and its value three times as great, 1929 being the low of recent years. The 1933 production was about 821,000 oz. From New Zealand, 165,000 oz. was exported last year. Papua and New Guinea contributed slightly over 100,000 oz. What the future price of gold will be nobody knows, but, even if it returns to the former level, Australian producers are almost sure of 110 shillings an ounce until 1940 through the Commonwealth Government's Gold Bounty Act, at present temporarily and necessarily suspended from operation.

Jan 1, 1934

but, returning to South Africa, for the next two years he was assistant general manager of the Simmer Deep Gold Mining Co., at Johannesburg. In June, 1911, he returned to New Zealand as general manager and consulting engineer for the Consolidated Goldfields of New Zealand, at Reefton, which position he held at the time of his admission to the 1nstitute in 1914. Early in September, 1915, he left New Zealand for active service in France. Corporal Sheppard B. Gordy Sheppard B. Gordy, born in Ansonia, Conn., in 1889, graduated from the Sheffield Scientific School in 1910 and with the degree of E. M. in 1912. He entered the employ of the Braden Copper Co. immediately on his graduation and remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time he had gone to Dayton, Ohio, to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9. Lieutenant Thomas Clarence Gorman Thomas C. Gorman, a lieutenant in the Second Tunnelling Company of the Canadian Engineers, was killed in France on Mar. 18, 1918. He was resting in his sleeping hut and was in the act of writing a letter when a bursting shell killed him.

Jan 1, 1920

(Under this heading will be published notes sent to the Secretary of, the Institute by members or other persons introduced by members.) Development and production. Member open for engagement. Past year in war mineral field work, operation and production. Ten years' thorough experience in both subordinate and executive positions, gold, silver and copper in the United States, Mexico, and South America. Age 37, married. Minimum salary $3600. Interview. South or East. A-577. Engineer and executive. Captain U. S. Army, age 36, expects discharge before July 1. Seven years' mining and metallurgical experience. Six years with large technical college as assistant professor of mining and directing extensive experimental work. Desires position as executive or research engineer with reliable company or as professor of mining with first-class college. A-909. Mining engineer. Twenty-five years' experience including mine and works operation, construction, plant installation, and mine examination. Speaks Spanish. A-1173. Metallurgical engineer. Twelve years' laboratory and operating experience, covering copper blast furnace, roasting, reverberatory smelting and latest Cottrell treater practice on copper dust and zinc dust. Technical graduate. 36 years of age, married. Highest recommendations. Open for immediate engagement. A-2354. Mining engineer. Junior Associate. At liberty about July 1. Captain Heavy Artillery. Single, age 24. Go anywhere. Best refer-ences. A-2843. Engineer. Age 26, single, graduate Missouri School of Mines, B. S. in Mis. Met. E. Desires position with oil or metal company in any capacity. Location immaterial. At present engaged, desires change. A-2844.

Jan 7, 1919