Search Documents

By Ross W. Smith, Salim Akhtar

INTRODUCTION Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collectors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By R. D. Groves, G. M. Potter, T. H. Jeffers

Experiments on ammonium carbonate leaching of native copper ores crushed to 1-inch size showed that in 30 days 55 percent of the copper was extracted from 0.7 percent copper conglomerate-type ore, and 85 percent was extracted from 2.1 percent copper amygdaloid-type ore. Cupric ions were not necessary to initiate leaching, and dilute solution containing only 2.2 grams per liter NH3 and 1.9 grams CO, was a suitable solvent. Copper was recovered from the leach liquor by solvent extraction and electrolysis of the strip solution. Cyclic testing of the leach-solvent extraction-electrolytic procedure is in progress on a 6-ton charge of minus 12-inch conglomerate-type ore assaying 2.2 percent copper. Oxygen is metered to the closed leach vessel as required by the leaching reaction. Initial copper dissolution was much slower than from minus 1-inch ore, but the leaching rate then markedly improved.

Jan 1, 1974

By Frederick Prime

AT the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wrought-iron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on account of cost, strength, etc. Karsteu* says : " Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron; or as a ductile, weldable, soft metal, which can only be melted at the * Karsten, Handbuch der Eisenhüttenkunde, 3d ed., vol. i, p. 6. Berlin, 1841.

Jan 1, 1876

By S. F. Willey

Difficulties encountered in justifying replacements for overage mobile mine equipment at the Gay mine are common to most mining operations. More critical management reviews, resulting from ever rising capital expenses, increased such difficulties. These increased difficulties are especially apparent to those who are primarily operators and are not statisticians, mathematicians or computer men. The Gay mine is located 17 mi east of the town of Fort Hall in southern Idaho. This open pit operation annually supplies the J. R. Simplot Co. and the FMC Corp. with 1.5-2.0 million tons of phosphate ore. Stripping ratios average approximately three bank cubic yards of waste per ton of ore mined. The mobile mine equipment fleet consists of ten 24-cu yd scrapers; twenty-one 30-50-ton end-dump trucks; four 3%-4%- cu yd shovels; fifteen dozers in the D-8 and D-9 classes; and three road patrols. Equipment replacement is based on the results of evaluations made on individual units.

Jan 9, 1972

By J. R. Ross, J. B. Rosenbaum

Bureau of Mines research has resulted in the development of fluid- bed ion-exchange columns for recovering uranium from slime pulps. In pilot plant tests, slime slurries containing up to 6 percent solids were processed at flow rates of 10 gallons per square foot per minute with high uranium recoveries and efficient resin loadings. Uranium was effectively eluted in a laboratory fluid-bed elution column at eluate-to-resin ratios of less than 5:1 and eluate flow rates of 3 gallons per square foot per minute. Construction costs of mills using these improved ion exchange techniques are estimated to be 25 percent less than for mills using solvent extraction of clear solutions. For mills having a capacity of 2,000 to 2,500 tons of ore per day, the saving would be in the range of $2.5 million. In addition, a saving of about $0.80 per ton of ore in total operating costs is indicated.

Jan 1, 1973

By George W. Lower, Robert B. Booth

The use of cyanides in the extraction of gold and silver is well known1 Such extractions employ concentrations of cyanide in the range of 0.02-0.25% sodium cyanide equivalent in leaching cycles of 24-48 hr and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold.2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure.

Jan 11, 1965

By A. Thies, A. Mezcer

The Haile mine is situated in Lancaster county, South Carolina, twenty miles south of Lancaster. The topography of the country is characterized by low hills rising generally less than two hundred feet above the many small creeks which traverse the surface. The road from Kershaw, the nearest railroad station, 3 1/2 miles from the mines, leads through woods with sandy soil and cottonfields. In many places it lies on the bare rock and shows that the adjacent covering of soil and earth is usually not more than one foot thick, and often less. This covering is to a great extent sand. Close by a bridge, about one mile from the mine, large round boulders of diabase may be observed. The country-rock seems to be exclusively talcose slate, with a general strike varying from N. 45' E. to N. 70' E. These variations may be seen in the immediate neighborhood of the mines, the large open cuts of which present exposures favorable to such ob-

Jan 1, 1891

By David S. Butts

There are many solution mining operations that use solar ponds as a mineral recovery step. Other locations in the world are now under investigation to recover minerals by solution mining but require the cheap energy of solar ponds to make the recovery viable. This paper shows a step-by-step material balance system that can be used in both simple and complex solar ponds. Use of this system will help the engineer determine if solar ponding efficiency can be improved or if solar ponding will work at all with a given set of conditions. Even the most complicated solar pond can be reduced to six flow streams. These are (1) feed, (2) exit, (3) leakage, (4) entrainment, (5) salts, and (6) evaporation. The equations developed in this paper will allow the solar pond engineer to easily evaluate the effect of each of the flow streams on the mineral production of a pond or pond complex.

Jan 1, 1985

Western Mining Corp. has announced plans to expand its mining operations at Kambalda, and to build a nickel refinery at Kwinana, near Perth, Western Australia. The refinery will use the ammonia-leach hydrogen reduction processes of Sherritt Gordon Mines Ltd., and it is expected that by 1970, when the expansion is scheduled for completion, Western will be the world's fourth largest nickel producer. Although estimates have not been finalized, the total cost is expected to be about $55 million. The mine and mill facilities at Kambalda, which began production in June 1967, are now producing at the rate of 11 million lb of contained nickel per year. The company estimates the sulfide ore reserves at Kambalda and St. Ives at 10.4 million tons averaging an usually high grade of 3.8% nickel, or about 790 million lb of contained nickel. In addition, silicate and oxidized ores have been located in both areas.

Jan 3, 1968

By J. Wayne Erickson

Hundreds of millions of dollars have been spent to discover or purchase uranium resources that cannot, or should not, be mined with conventional methods if human, natural and financial resources are to be conserved. Three years ago, an industry-supported research stud was initiated to determine whether a safer and more efficient (in terms of cost and environment) uranium mining method could be designed to replace existing techniques. As a result of this study, the "underground in situ" method was conceived and developed to the stage where it is now feasible. This approach involves: (1) sinking a shaft; (2) driving a drift on the ore horizon the length of the ore body; (3) drilling almost-horizontal long holes the width of the ore body; and (4) oxidizing and leaching the uranium drawn from these holes. The method is unique in that the uranium is removed with a minimum of disturbance to the natural hydrology of host or surrounding sands.

Jan 11, 1978

By Guy R. Johnson

Like many other similar plants the ore-washer of the Longdale Iron Company has been a growth of years. In its principal features there is probably nothing new, as the type is that of the well-known " log-washer." Some of its minor details may, however, be of interest to those members who have to deal with the washing of large quantities of brown iron-ores, the principal gangue of which is clay. * Until 1883, the ore at Longdale, being of unusual purity, needed no washing, and was charged to the furnaces as it came from the mines—both lump and fine—the only attempt at cleaning being the' picking over a screen of 1½-inch iron bars, 3½ inches from center to center, set in the top of the bins through which the cars for the furnaces were loaded." In 1883 it was no longer possible to win the ore by open cuts, and regular underground work became necessary. It was very

Jan 1, 1895

By Vassiliki G. Stavropoulou

Although plane-strain is the preferred method of analysing many rock mecahnics problems, little is known about the behaviour of rock under this loading condition. A simple and inexpensive apparatus has been built for laboratory testing of rocks in plane-strain conditions. A thorough .investigation of the specimen geometry and the friction end effects showed that the results can be considered as reliable. The behaviour of a brittle sandstone in the simplest plane-strain condition [(03 = 0)] is significantly different than that of the uniaxial compression [(02 = U3 = 0)]. The plane-strain values of the Young's Modulus and the Poisson's Ratio are decreased in comparison to the corresponding uniaxial values. Dilatancy is also reduced in plane-strain, whereas the pre-failure brittleness of the rock increases. The most dramatic effect of the plane-strain condition is that on the strength of the sandstone, which increases by 49 per cent in comparison to its uniaxial compression value.

Jan 1, 1982

By R. Taggart, G. R. Purdy

DURING a study of the tempering of ß-quenched alloys of cobalt in titanium, parallel lines were observed crossing certain faces of retained-ß crystals in the early stages of tempering, Fig. 1. The lines closely resemble stress-induced martensite' or substructures attributed to clusters of faults in titanium-nickel2 and copper-silicon3 alloys. The markings were observed only in intensely etched quenched and tempered alloys having compositions ranging from 4.5 pct* Co (the composi- formed by the lines was reproduced upon repolishing and reetching. Close metallographic examination indicated that the markings were troughs, Fig. 2, and that the characteristic surface substructure persisted within the troughs. The occurrence of the troughs was associated with the age hardening reaction due to the metastable u) phase (previously reported in titanium-cobalt alloys by Raub and Beeskow4 and indicated in this work by the broadening of 0 diffraction peaks and by hardnesses approaching 600 Dph). The troughs

Jan 1, 1961

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By Harold F. Yde

Hydraulic tailing fill in the Butte deep-level mines resulted from studies made in 1958 by The Anaconda Co. Mining Research Department. At the time of the study, dry mine tailing was hauled via rail cars from the Anaconda tailing ponds, 25 miles distant, to the tailing fill plants of the underground mines at the Leonard, Anselmo and Mt. Con mines. Presently, tailing from the Weed concentrator in Butte is delivered to the Kelley shaft via pipeline and stope filling has become automated. Tailing at 30% solids is pumped 8000 ft horizontally and upward from the concentrator to the Kelley fill plant, where it is dewatered and deslimed by three Krebs cyclones. These discharge the material into the cased and grouted mine delivery boreholes at desired densities of up to 70% solids. The vertical boreholes and 4-in. rubber-lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the 3-in. stope-filling, unlined Victaulic pipelines.

Jan 1, 1970

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts1-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presentation of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about ¼ in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 7, 1958

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern US and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales. This resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 67 Gm3 (423 billion bbl) of oil could be recovered by HYTORT processing of surface minable eastern US shales. Recently, American Syncrude Corp. and Southern Pacific Petroleum NL have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized.

Jan 1, 1986

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919