Search Documents

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By B C. Povey, K Lagutin, M Mryasov, V Noll

The current Stoilensky magnetite concentrator comprises a three-stage crushing circuit followed by three stages of ball milling, grinding and concentration to produce a magnetite concentrate with 66.5% iron (Fe). The plant is built in four lines, three lines having four mills and one line with five mills, to treat 32 Mt/y of ore and produce 13.9 Mt/y of concentrate.NLMK, the owner, is Russia’s third largest steel maker and while the ore from the Stoilensky Mining and Beneficiation Plant (SGOK) provides the bulk of their supply, they still must buy ore from external sources at world prices. A decision was taken to expand the SGOK operation to supply all the NLMK concentrate, including the production of pellets.To commence the expansion, high pressure grinding rolls (HPGRs) were introduced as a fourth stage of crushing ahead of the first ball mill. This was a relatively low capital cost expansion and increased production by 12 to 15%, the cost being much less than an additional grinding line. The importance of this development was that earlier introductions of HPGRs in Russia had presented several problems so there was some reluctance to the initial concept. The even greater significance was that nearly every magnetite plant in Russia had a three-stage crushing circuit so the successful introduction of HPGRs was of interest to many operators.The design was developed by a team, consisting of Worley Parson, Mineralconsult and PiterGORproject (PGP), for the first four units to fit inside existing building structures. The first two units were commissioned in March 2016 and the next two units in May 2016, and production improved by over 12%. The design of the installation of the final four units is in progress and the installation is expected in late 2017.CITATION:Povey, B C, Noll, V, Lagutin, K and Mryasov, M, 2017. Introducing HPGR quaternary crushers in a Russian magnetite operation – challenges and solutions, in Proceedings MetPlant 2017, pp 84–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Limnological processes are often overlooked when trying to assess the long-term water quality of pit lakes. It is essential to deal with these aspects, since they determine the geochemical and redox conditions around the submerged reactive rocks. Underground mining at East Sullivan (northwestern Quebec, Canada) stopped in 1966. Two adjacent stopes, 91 and 106 m deep, were left open to the surface, with roughly circular apertures of about 7700 and 18 000 m2. Water filling of the two glory holes went on over three decades and overflow began in 1999. Surface water pHs values were near neutrality as late as 1994 (6.3 - 7.0) but had become acidic by 1999 (2.6 - 3.5). Limnological processes were investigated in late-1999 and early-2000, with temperature measurements at 1 m intervals and sampling of the water columns before and after the late fall density inversions. A strong chemocline-thermocline was observed at 15 m. Above the chemocline, the water had low pH (3.2), no alkalinity, and low Na, Ca and sulfate. Below the chemocline, the concentrations of these parameters and the pH increased, with pH at 5.5 - 6. Consistent with the low pH values present in the upper 15 m, the concentrations of Al, Cd, Cu, and Zn were high near surface, and decreased below the chemocline. Dissolved oxygen concentrations as well as Eh decreased with increasing depth. Alkalinity integrated over the entire water column below the chemocline was at least six times larger than the acidity inferred from Fe2+ and Fe3+ concentrations. The temperature survey showed that seasonal density inversions do occur in the water column. The inversions do not involve the entire water body, since the surface to depth ratio is too small for a complete overturn. Oxygen from surface waters is carried to the bottom where it oxidises sulfides, until its depletion. Residual Fe2+, stable under anoxic conditions, is displaced upward by the next dense water incursion. It eventually reaches the thermocline, but only after many successive incursions. There, its oxidation to Fe3+ allows hydrolysis, which consumes dissolved and wall-rock alkalinity. It is only in 1999 that alkalinity was finally exhausted and that the pH shifts to acid values. The low pHs in the surface waters allow a build up of Fe3+ and Al3+, and desorption of metals from colloids. Buffering is assumed to be controlled by wall-rock oxyhydroxides in surface waters, and by carbonate minerals in the bottom waters. Because the seasonal overturns are far from being complete, the large amounts of alkalinity acquired from the wall-rock in the bottom waters cannot balance the acidity of near surface waters. Hence the surface water is acidic.

Jan 1, 2003

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By Dods G. H, Hewitt W. V

Ashton Mining Limited is currently one of the active companies undertaking gold exploration in Indonesia. Presently 7 Contract of Work areas are being explored for hard rock and alluvial gold. Hard rock exploration is focussed on the Tertiary volcanic arc terrains in which a variety of epithermal mineralisation styles have been identified. At the regional stage remote sensing techniques using Landsat, Spot and SLAR imagery where available, and photogeological studies are carried out in parallel with regional reconnaissance fieldwork programmes. These involve geological mapping and geochemical drainage sampling. Remote sensing techniques have proven useful in both the extrapolation of known geology and the identification of tectonically favourable settings as controls to mineralisation and volcanicity. The variety of mineralisation styles and settings is reflected in the highly variable geochemical signatures encountered. This has necessitated the refinement of sampling methods and sample preparation techniques for pan concentrate, stream sediment and soil samples in specific project areas. At the detailed prospect stage, mapping with particular attention to structural controls, wallrock alteration assemblages identified by petrog- raphy and XRD clay mineralogy, have proved useful in focussing drill targets. Drilling to date has utilised conventional diamond core drilling methods, the use of lightweight, man-portable "Winkie"-type rigs and hammer auger bedrock sampling systems. Geophysics methods successfully employed on various projects have included airborne magnetics and radiometrics, detailed ground magnetic surveys, VLF-EM and SIROTEM.

Jan 1, 1991

By J Jackson

The term geometallurgy (or geometallurgical) first appeared in the literature some 40 years ago and has a wide range of definitions and perspectives which increases the barriers of communication between practitioners and across functional groups and management levels within organisations. However the consistent theme running through the diversity of definitions and perspectives is the requirement for close collaboration between the relevant disciplines. This concept of geometallurgy arguably goes back to the earliest days of the exploitation of mineral deposits, through the mid-1500s to the beginning of the 20th century.This holistic and integrated view was diminished during the 20th century due to a number of factors which included the commencement and continuing upward trend of large-scale mining and the expansion in production, the rise of scientific and classical management theories and methodologies, increase in specialisation and the development of traditional project planning. The re-emergence of geometallurgy in the late 20th century required the relevant functional units and disciplines to collaborate as a team. This necessitates a common understanding that the geometallurgical program’s goals must be obtained, which requires clear and consistent communication, particularly with the modern trend of virtual teams.A multi-dimensional construct is proposed to assist in providing a consistent approach in the communication of the context and purpose of both general and specific geometallurgical programs, thus simplifying communication. This geometallurgical construct consists of the dimensions of process span, response knowledge, variability knowledge, spatial knowledge, application and project phase in relation to extraction process(es) applied to geological materials from a mineral deposit. These dimensions are then linked to the phase of mineral project development in which the geometallurgical program is being applied, which ranges from advanced exploration through to operational execution. This paper outlines the multi-dimensional construct with examples of how the context, purpose and scope of geometallurgical programs can be clearly delineated and communicated.

Sep 5, 2011

By C R. Fountain, W R. Cannings

The zinc-lead-silver mineral resource at Lady Loretta ranks amongst the worldÆs richest when measured in terms of in situ metal grades. However, the project remains undeveloped 28 years after its discovery in 1969. The primary obstacle to development has been the fine and complex grain structure of its ores, which make flotation concentration inefficient even with fine grinding. The size and remote location of the deposit have also hindered exploitation. BUKA planned to directly fume the volatile target metals from the ore when it acquired the project. Intensive, post-acquisition modeling showed the innovative processing route to be uneconomic, notwithstanding high metals recovery and low waste content in fume product. Progressive modifications and supplements to the underlying fuming process enhanced economics and resulted in a new mine-to-metal processing route for zinc-lead-silver ores. The proprietary, three-stage BUKA Zinc Process offers technical, economic and environmental advantages. It is expected to find widespread application in the treatment of ores and residues. However, neither continued R&D nor application to Lady LorettaÆs currently delineated resource can be justified under prevailing market conditions. The objectives and results of each step in the process development sequence are outlined with reference to their impact on the commercial viability of the Lady Loretta project.

Jan 1, 1998

A comprehensive analysisof rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging, interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcorc is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure.

Jan 1, 1990

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

As partition curves are widely employed to characterize screening efficiency which, by definition, should include a time parameter, it is shown, perhaps for the first time, that time is already included in the partition curves and how. Laboratory and plant results are used to show how screening efficiency depends on feed composition, near-mesh and oversize material and screen motion, and how these factors may combine to give an erroneous result that two identically efficient screens are different and two screens of different efficiency are identical. Reasons are given which show why a renewed interest in screening would benefit not only screen engineers and operators but also those concerned in formulating standard specifications of screen analysis methods.

Jan 1, 1984

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By D Bradshaw, J R. R de Villiers

The non-stoichiometric sulfide mineral pyrrhotite (Fe(1-x)S), common to many nickel and platinum group element (PGE) ore deposits, occurs in varying crystallographic forms with the different types exhibiting subtly different physical and chemical properties. These differing properties are likely to influence the flotation performance of pyrrhotite, which in the case of PGE operations is actively recovered, whereas in nickel operations pyrrhotite is depressed. In this study, examination of natural pyrrhotite samples from Southern African and Canadian nickel and PGE ore deposits revealed a variety of pyrrhotite compositions in terms of iron content (Fe7S8, Fe9S10, Fe11S12) and solid solution nickel concentration. Pyrrhotite composition was correlated with its mineral association depending on whether non-magnetic pyrrhotite occurred in conjunction with troilite, non-magnetic pyrrhotite occurred as single phase pyrrhotite, magnetic pyrrhotite occurred as single phase pyrrhotite or whether the two phases; magnetic and non-magnetic pyrrhotite co-exist. Subsequent microflotation tests of selected single phase pyrrhotite samples revealed that the non-magnetic pyrrhotite is slightly more floatable than magnetic pyrrhotite. Microflotation tests also showed that varying flotation responses occur between differing magnetic pyrrhotite samples. These differences in flotation performance are postulated to be a result of the effects of varying pyrrhotite crystallography, trace metal content and mineral association on pyrrhotite oxidation, formation of surface species and subsequent adsorption with xanthate collector.

Jan 1, 2008

By Hommert P. J, Brown B

Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. An improved damage model based on microcrack growth in tension allows finite element calculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model.

Jan 1, 1990

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

By E Deucker, A White

Gold Fields Australia (Gold Fields) has identified that improving productivity through more detailed shift planning and operational control of mining activities is a key driver to the success of their business. The Hamlet mine was chosen as a pilot site to trial a system that would allow production engineers and shift bosses to align the execution of short-term activities with the longer-term goals of the organisation.Gold Fields partnered with Deswik to introduce an on-site, collaborative, web-based system to allow mine planners to quickly build-up a detailed, activity-based, shift schedule for the coming week from the 13-week plan. Multiple stakeholders could then review and alter the plan, and then track and manage the execution of the activities.The system is designed to be integrated with production data capture systems to allow tracking of progress towards completion for each activity, as well as to plan and monitor the equipment operating in the mine. Integration of systems allowed engineers to use the large quantities of production data being captured to make informed decisions in the operations environment.The system replaced a complex set of spreadsheets that required expert users in Gold Fields to maintain. By capturing the data in a central database, the planning process is transparent and historic data from the execution of activities is available for analysis to improve productivity in the future.The system has ensured that the highest priority and critical path activities for the business are completed at the right time, improving the efficiency of operations.CITATION:Deucker, E and White, A, 2017. Productivity improvement through collaborative shift planning and tracking, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 225–234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Stewart R. D, Lawrence W, Youl M. J

The trend towards contracting by major coal mining companies such as BHP Coal and MIM Ltd is examined. Reasons why this trend is occurring are discussed and the concept of partnering is examined. Two case studies are given: the Mt Owen Mine in the Hunter Valley, NSW and the South Walker Creek Mine in the Bowen Basin, Queensland.

Jan 1, 1997

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

Traditionally, the development of a mineral resource project goes through a fairly set pattern of decisions from what commodities to search for; where to look; how to locate; what are the reserves; how can they be exploited with optimum returns for all stakeholders; where are the markets and what will be the price received; what financing arrangments? However, due to the unique nature of most mineral resource properties, the relative significance of individual parameters on the ultimate development decision will vary from project to project. Sensitivity analysis in its formal sense is most frequently related to the economic analysis of a project particularly in conjunction with the ultimate development decision making process, and acknowledges the uncertainty of the actual values with their impact on the corporate decision making yardsticks. In many cases, this analysis merely adds more values to confuse the decision makers who may well opt for some subjective rationale to overcome the numeric confusion. However, sensitivity analysis should be used more frequently to exploit the development dollar to its maximum, THROUGHOUT the phases leading to the development decision. It is essential to identify the critical inputs to the various decision tiers in a project as early as possible and direct the funds to ensure that these parameters are determined as accurately as possible. Examples are used to illustrate the need for an even-handed quantification of the parameters which affect the outcome of decisions en route to the final one while minimising the risk in making an optimum assessment in relation to development funds Available.

Jan 1, 1983

This paper puts the view that, for one gold deposit in Victoria at least, the Australasian Code for the Reporting of Identified Mineral Resources is severely deficient. The author questions whether or not the Code constrains the proper dissemination of information relevant to resource valuation. The author offers a view about the estimation of inferred resources, and provides data believed pertinent to the proper valuation of Ballarat Goldfields Ltd Ballarat East Project.

Jan 1, 1990