Search Documents

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By M B. Lovitt

At present there exist few engineering calculations and principles to determine exclusion zones for personnel in the vicinity of underground explosive storage areas. This paper is written to encourage discussion and proposes a method to determine the impact of a blast wave through scientific principles. Then, criteria to determine an ‘exclusion zone’ need to be identified.There has been much work on identifying the pressure rise and the energy of explosive detonations underground but little to develop standards in criteria that can be used to identify exclusion zones for useful design of underground infrastructure. The author presents the newest ways of calculating the pressure rise and energy (impulse) of detonations and puts forward some criteria to be used in the identification of personnel exclusion zones to spark peer review and discussion of these criteria towards developing standards for engineering design.Smith and Sapko (2005) used Sach’s scaling laws to develop a relationship for both pressure rise and impulse, which incorporated factors for intersections. Intersections will have a large bearing on the peak pressure and the energy of the blast wave and needs to be incorporated. Silvestrini, Genova and Leon Trujillo (2009) developed the scaling laws with an energy concentration factor to predict blast propagation in partially confined geometries and together the author has proposed equations for determining the peak side pressure and the impulse in a tunnel. Given the weight and type of the explosive, the average cross-section of the tunnel complex and the number and type of intersections encountered, the pressure and impulse can be calculated.The military has carried out many investigations as to the influence of blast pressure and impulse on the human body. Lung damage, ear damage and velocity knock down are three of the criteria standards that are presented as possible methods of determining exclusion zones around an underground explosives magazine. The author suggests that the velocity curves presented by Bowen, Fletcher and Richmond (1968) could be an acceptable method of determining an exclusion zone as it incorporates the side pressure and the energy of a blast wave to determine the ability of the wave to knock down personnel.CITATION:Lovitt, M B, 2014. Exclusion zone calculation for underground explosives storage, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By H Aoki, A Nakayama, K Morita, S Yamada

The thermal conductivity of mold flux is crucial for optimising the productivity and quality of steels. This study investigates the thermal conductivity of molten oxides, including CaO-BO1.5-AlO1.5 (CBA), CaO-BO1.5-AlO1.5-SiO2 (CBAS), and CaO-MgO-BO1.5-AlO1.5 (CMBA) melts, using a hot wire method. Additionally, their structure is examined using Raman spectrometry and magic angle spinning nuclear magnetic resonance (MAS-NMR) to explore their relationship. Furthermore, first-principles calculations are employed to assess the covalency of each bond in the melts for a more quantitative analysis of their relationship. The study confirms that an increase in the CaO concentration of the CaO-BO1.5-AlO1.5 melts reduces the amount of bridging oxygen and consequently decreases thermal conductivity. The covalency of the B[4]-O bond is highest, especially when the second-nearestneighbour Al atoms transition from Al[6] to Al[4], forming the AlB3O7 structure with B[4]. The relationship between thermal conductivity and the structure of CaO-BO1.5-AlO1.5-SiO2 melts can be quantitatively assessed using the degree of polymerisation of the network structure and the variation of covalency as indicators. Furthermore, replacing CaO with MgO in the CaO-MgO-BO1.5-AlO1.5 melts reveals a mixed alkaline earth effect on thermal conductivity.

Aug 21, 2024

By C R. Stanley, D Lawie

The measurement of error in assays collected as part of a mineral exploration program or mining operation, including errors introduced during sampling, sample preparation, or geochemical analysis, historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation. CITATION:Lawie, D and Stanley, C R, 2012. Average relative error in geochemical determinations - Clarification, calculation and a plea for consistency, in Proceedings Sampling 2012 , pp 181-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

IT is very difficult for a founder engaged in jobbing work, comprising all sizes and classes of castings, to appreciate that the analysis of the iron he is using cannot entirely fill the situation he desires for his varied classes of work. Neither is there any panacea in the shape of an iron mixture that will suit the whole of his floor for the day.From his own experience he generally alters his cupola charges during the cast, endeavouring to meet at the same time the requisite metal composition for the castings he is about to pour.The founder on repetition work is in a much better position to stabilise his methods, arrive at a certain pig-iron' analysis, regulate...

Jan 1, 1926

By L Clarke, R N. Campbell, F Bourke, J Anderson

Lithological units have been classified geotechnically with mechanical tests and discontinuity measurements from the GRD Macraes Limited, Macraes Gold Project and Rotowaro coal mine open pits, New Zealand. Using these measurements slope stability probability classifications (SSPC) have been quantified based on an adaption of Hack's (1998) SSPC system which places less influence on rock quality designation and unconfined compressive strength than previous slope/rock mass rating systems. The Hack weathering susceptibility rating has been modified by using the chemical index of alteration values from XRF major element analysis. Slaking and weathering is an important parameter in slope stability in the Waikato Coal Measures and Otago schist lithologies and hence a non-subjective method of assessing slaking/weathering in relation to the chemical index of alteration has been introduced. Other major components of this adapted SSPC system are the inclusion of rock moisture content and rock strength anisotropy effects on slope stability. This paper explains the systematic approach of using the adapted SSPC system to classify slope stability probability. The main modifications of Hack's SSPC system are the introduction of rock intact strength derived from Mohr-Coulomb failure criteria which has been adapted for varying moisture content, weathering state and confining pressure. It is suggested that the subjectivity in assessing intact rock strength within broad bands in the initial SSPC system is a major weakness of the initial system. Initial comparison of rock mass friction angles, cohesion and strengths derived from the adapted SSPC are compared with results derived from modified Hoek-Brown criteria, MRMR and SMR classification systems. The advantage of the modified SSPC system is that slope stability probability, maximum batter and overall slope height and overall slope angle for open pit walls can be predicted in addition to orientation dependent and orientation independent stability. Examples are provided, using the modified SSPC system to predict initial optimum pit slope designs in proposed greenfield mine sites.

Jan 1, 2000

The present Pacific Ocean arose from rapid sea-floor spreading that commenced in the late Mesozoic, and continues to the present day. It started within what is here called the Medusa complex of seaways, basins and troughs with spreading ridges and volcanic arcs, that girdled the earth, including the Palaeotethys and Neotethys of Eurasia between Gondwanaland and Laurasia. Detailed mapping and analysis of palaeofaunas and volcanic arcs indicate that several seaways, rather than one or two, extended throughout Tethys, and into areas now occupied by the Pacific Ocean. The Medusa complex developed under a long sustained wrench regime, right lateral at least from New Zealand to Eur.ope, and saw the origin, maturation and closure of elongate and oval basins under erratic sea-floor spreading, in which no Eulerian pole of rotation remained fixed for long. The name Medusa stems from the analogy of snake-like writhing hair to the constantly shifting development of basins and orogens within the complex. The Indian Ocean split and opened up Gondwanaland concomitant with the later development and deformation of the Tethyan segment- of Medusa, whereas, to the east, the Pacific Ocean opened within Medusa itself, and dispersed Medusa around the rim of the Pacific through sea-floor spreading and strike-slip faulting.

Jan 1, 1987

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

By Lyman GJ, Davis JJ

Models which have been presented in the literature consider only selected aspects of dense medium cyclone operation, are empirical in nature and generally relate only to severely limited ranges of operating parameters. This paper reports progress towards development of a more comprehensive and robust model. The data base consists of partitioning parameters developed using density tracers and conventional coal sampling and analysis techniques, together with recordings of parameters such as cyclone dimensions, feed pressure, medium size distribution and product media densities.. These data were drawn from 15 Australian coal preparation plants. To elucidate the effects of important operating parameters on medium behaviour and on the partitioning of large particles a series of pilot scale tests was also conducted. The present model consists of eight sub-models which relate to particular aspects of dense medium cyclone operation such as medium flowrates and densities, or size- by-size separation densities and Eps. The model structure follows a logical progression which clearly demonstrates the importance of understanding medium behaviour before attempting to predict partitioning performance. The model also attempts to define the conditions under which yield losses due to unstable "surging" discharge may occur.

Jan 1, 1987

By Christie AB, Bull VH

The geological environments of gold deposits are reviewed in relation to the strong resurgence in exploration for gold since 1979. The resurgence is due mainly to New Zealand's geological endowment with gold and its history as a gold producer. Major past production was from Cenozoic placers of Otago and Westland, late Cenozoic epithermal deposits of the Hauraki Goldfield, and the respective Paleozoic and Mesozoic lode deposits of the Reefton and Otago Goldfields. These same geological environments are the targets of current exploration, mainly in extensions of previously mined deposits. On the Westland and Otago Goldfields alluvial and fluvioglacial gravel placers, mainly representing lateral and depth extensions of previously worked ground, are being mined and prospected. Gold production in 1984 was exclusively from these deposits, and the development of mobile concentration plants has resulted in a great increase in mining activity. Mineralised zones adjacent to previously mined lodes in the Hauraki Goldfield, Reefton Goldfield, and at Macraes Flat (Otago Goldfield) are being intensively explored. At Waihi (Hauraki), an open-pittable resource of about 10 million tonnes of ore has recently been delineated. Some new deposit types and little explored environments are also receiving attention. They include: gold-sulphide quartz veins hosted in an alkaline granite dike in west Nelson; hot spring type gold deposits in fossil geothermal (epithermal) systems of Northland, the Hauraki Goldfield and the Taupo Volcanic Zone; and marine placers off the West Coast where an area of auriferous gravels has been outlined near Hokitika. There is potential in known deposits and prospects currently being evaluated for a large increase in gold production by the early 1990s.

Jan 1, 1986

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004

By Svensson J

The nickel segregation process is one of the methods for treating nickel oxide ores. In this process nickel oxide ores are heated together with a small amount of the carbonaceous reductants and halides to about 800-950¦C. The reduced nickel segregates onto the surface of the carbonaceous reductants in the form of metallic particles which are recovered by magnetic separation or flotation. Pilot plant tests for the extraction of nickel from nickel oxide ores have been made using nickel segregation process by means of a new roasting installation which is called the "Mechanical Kiln" (2.5m~ x 3m,') with autogenous heating. Nickel oxide ores containing about 2.5%Ni were mixed with 2.5%CaC12 and 2.7%coal, and continuously charged into this installation at the rate of 60kg/h in continuous operation for 30 days per trial.

Jan 1, 1980

This paper reviews the commissioning and operation of the process plant at Tolukuma over the past 18 months. The plant treats a high-grade gold and silver ore through a SAG mill followed by a conventional carbon-in- leach (CIL) circuit. Gold is

Jan 1, 1997

Callie underground gold mine is part of the Newmont Tanami Operations, and is now the primary provider of ore to the Granites processing Mill. The Callie underground mine has produced in excess of 7.6 million tonnes (Mtpa) of ore, since production began in 1998, with a current production rate of 1.9 Mtpa. Callie underground uses sublevel open stoping with extraction through a combination of primary and secondary stopes. The primary stope filling strategy utilises cement aggregate fill (CAF) to allow full recovery of secondary stopes. The Callie backfill operation has had a continuous testing program in place during this time, which has resulted in a great deal of information available for post fill analysis. All CAF placement into primary stopes for Callie has been via surface boreholes and this has given Callie mine an understanding of some of the issues related to borehole design, type of linings to use depending on angle, depth and quantity of fill into stopes. Finally backfill barricades at Callie have undergone a number of changes during the time to optimise the design based on whether CAF or sand fill is used. This paper discusses the CAF backfill practices and testing methods used for backfilling operations at Callie.

Jan 1, 2005

By Koh P. T L, Varnas S. R

Fluid flow, heat transfer and combustion in a nickel flash smelter have been investigated by numerical modelling and flow visualisation. The three-dimensional numerical model incorporates turbulent two-phase fluid dynamics, radiative heat transfer and combustion. The main features include the use of the k-E turbulence model, the Lagrangian tracking of particles, radiative heat transfer based on the spherical harmonics method, and chemical reactions. The predicted flow fields are in good agreement with data obtained from a series of flow visualisation experiments on a cold water model. The interaction mechanism between the fluid flow and the solid particles is examined for a range of particle sizes both with and without injected oil in a series of simulations. The heat transfer in the shaft is dominated by combustion and radiation, whereas the ignition of particles is influenced by the particle size and the added oil. Flow and temperature fields for both gas and solid particles are presented as well as the fraction of sulphur removed from the particles.

Jan 1, 1992

By H Plewes, A Bur, L Murray, J Pottie

Water recovery from tailings for reuse in mineral processing is essential to operation of mines in the Atacama Desert of Chile. With annual rainfall of 5 mm, the prudent and efficient use of available water resources is a major issue for the Escondida Mine and other mines in the area. The Escondida Mine is located at an altitude of 3100 m, in a very arid, seismically active part of the Atacama Desert of northern Chile. The site is located about 170 km from the coastal city of Antofagasta. From 1994 to 2002, tailings were discharged into the Hamburgo Tailings Facility, which comprises a series of æpaddiesÆ located near the open pit and mill. Because water in the region is only obtainable from groundwater sources, the paddy system incorporated a number of design features with the aim to maximise water recovery from the tailings. As part of the recent mill expansion to 237 500 metric tonnes per day, a new tailings facility, the Laguna Seca Tailings Facility, projected to be one of the largest tailings facilities in the world, was commissioned in 2002. Extensive studies were conducted for the design of the new facility to predict water recovery from the conventional wet disposal of tailings. The predictions were calibrated against the performance of the Hamburgo Tailings Facility and subsequently re-calibrated against actual performance during the first year of operation at the Laguna Seca Tailings Facility. Initial operation of the Laguna Seca Facility was marked by a coincidental change in tailings characteristics from design, which highlighted the need for thoroughly understanding tailings behaviour during deposition, and the parameters and deposition techniques that could enhance water recovery. Systems have been put in place to manage the tailings deposition and respond to changes in key parameters such that water recovery targets can be reliably achieved. This paper describes the background studies that were conducted to evaluate evaporation and tailings behaviour, summarises the water balance and then presents some observations from the commissioning and start-up of the facility.

Jan 1, 2003

By Withington J. T

The four major contracts for the construction of Museum Station are: 1) Installation of Soldier Piles, 2) Structural Contract including the temporary support, 3) Architectural Finishes which include Electrical and Mechanical Services and 4) Supply and Installation of lifts and escalators. Specific areas of interest include the fabrication, installation and removal of temporary support steelwork, the monitoring of ground loading, and the interface between the structure and. the temporary support. The information collated during construction confirmed the design assumptions and criteria. No major changes'were required in the design of the construction methods. The open cut excavation and construction of this major structure in an inner city area was significant by any standard and was successfully completed with minimum disruption to the public and without damage to adjoining or surrounding property.

Jan 1, 1981

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

By Isaac AK

The combination of shot-firing and stage loader, and a prop and bar support system is an accepted drivage method. The support configuration is based on the final prop density, and assumes relitively uniform load sharing between the props. During the development of a longwall faceline at a medium depth (approximately 600m) British coal mine using such a drivage method, a fall occured overnight, effectively closing approximately 40m of the drivage. The severity and speed of the fall prompted an investigation into the performance of the temporary support system installed prior to chock installation. This paper deals with the investigation which disclosed some major contributory factors towards loss of strata control.

Jan 1, 1986