Search Documents

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks. NOTATION Aa = stress change after excavation Eä EE, Eä = moduli of intact rock, single joint and jointed rock Eb = elastic modulus of the bolt k, = normal stiffness of joint Ab = cross section area of the bolt A, = area of influence per bolt ab = axial bolt stress e, = axial strain of the bolt eä e,, ej, = strains of intact rock, joint and jointed rock Ai = area of the joint ,r+ = shearing resistance of the bolt (at the joint) a = normal stress at the joint plane aäa3 = major and minor principal stresses c;, 4i; = cohesion and friction angle of the joint 0 = angle between the bolt and the joint a = inclination of the joint to the vertical axis P = bolt density parameter u, = convergence of unsupported tunnel section u, = convergence of bolted tunnel

Jan 1, 1992

By L Cooper, J Sharma, M J. Hendry

Thick clay tills below potash mine tailings and brine ponds are important natural barriers protecting fresh water aquifers in Saskatchewan. Centrifuge modelling was applied to assess geochemical processes and impacts of dilute brine (0.1 M NaCl) migration through clay till core samples obtained from non saline, unoxidised clay till at a mine site. At accelerated gravity of 876 + g, during each day of centrifuge modelling, flow driven through a 52 mm length core simulated transport through a 45 m thick clay over ~2100 years. Hydraulic conductivity, monitored continuously before and during brine permeation, was low and relatively constant (8.5 + 10-12 m/s), confirming that confining stresses prevent permeability increase. Core density and porosity measurements confirmed that reactive transport occurred under realistic in situ conditions. Breakthrough (defined by C/C0 = 0.5) of non-reactive Cl- occurred at 25 days. The slight delay for Na+ breakthrough, associated with small increases in Ca2+ and Mg2+ concentrations in the effluent were attributed to ion exchange, but carbonate reactions were relatively unimportant. Cation exchange analysis of core samples was inconclusive without corrections for porewater Na+ and carbonate dissolution. Geochemical processes that were observed during centrifuge modelling were successfully simulated using the 1D geochemical transport code PHREEQC. Solute transport was dominated by diffusion with limited ion exchange to delay Na+ migration. Brine would not break through a 45 m thick clay for tens of thousands of years. Based on these findings, the thick clay till at this site, if laterally extensive and undisturbed by drilling activity, is likely to act as an effective natural barrier to vertical brine migration over the long term.

Jan 1, 2003

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By Liu C. H, Juang Y. F

Coal/gas outbursts were one of the rather difficult safety problems faced in the coal mines of this Country, with coal fields characterized by frequent disturbances of folds, faults and pinch-offs. With average mining depth about 500m below surface, several such accidents occurred with up to 500 tonnes of coal outburst. In recent years, after a series of improving countermeasures had been undertaken, gas outburst accidents had been greatly decreased. The characteristics of gas outbursts in Taiwan coal mines include relating to coal petrography, mining depth and the other deformation forces. All these have been investigated, trying to determine the parameter of outbursts under natural conditions. The preventive countermeasures include predicting tests, de-stressing boring in coal seams, the emergency procedures during outbursts and certain improving options.

Jan 1, 1988

By Erickson M. E, Smith C. K, Carswell J. T

Thirteen holes totalling 3200m were surveyed using a downhole time domain Geonics EM37 system at the 830 metre level within the CSA Mine, Cobar, New South Wales, in order to search for blind, electrically conductive sulphides at some distance from exploration drillholes. A significant off-hole conductor was detected in only one drillhole.Geophysical modelling and interpretation of the survey results indicated that this off-hole conductor was caused by a sulphide lens 30 metres from the drillhole at a hole depth of 220 metres.

Jan 1, 1990

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993

By Rospigliosi RT, Krouse HR

The San Vicente stratabound zinc-lead rhythmite deposit, Peru, is hosted in carbonates of the Late Triassic - Early Jurassic Pucara Group. These strata were deposited in a large, shallow water, carbonate platform which extended nearly continuously for 150 kilometers (north-south) in the eastern part of the Pucara basin.The distinctive sulfide-bearing rhythmites occur in three dolomite units which, from bottom to top, include the San Judas horizon with one sulfide-bearing manto; the San Vicente horizon with seven sulfide-bearing mantos including the main ore horizon; and the Alfonso horizon with three sulfide-bearing mantos. The dark gray sulfide-bearing dolostone layers range in thickness from a few millimeters to a few centimeters and contain variable amounts of carbonaceous material, pyrite, quartz, fine-grained sphalerite and galena. They are bordered on each side by selvages of yellow to red-brown coarse-grained sphalerite containing minor amounts of galena. Coarsely crystalline white or gray sparry dolomite is found between the coarse-grained sphalerite layers. Although commonly stratiform and uniform in thickness, the dark layers curve, "pinch out," coalesce, and form "islands" and "peninsulas."Mineral replacement textures, the paragenetic sequence, and presence of sparry dolomite, bitumen, intraformational breccias and isotope data support a hydrothermal replacement origin by metal-bearing solutions that deposited the ore and related minerals in space previously occupied by dolomite and evaporite minerals. The alignment of the Zn -Pb deposits, and at San Vicente the orientation of the mantos, the spatially and temporally associated igneous sills and the tourmaline-bearing sandstone support hydrothermal mineralization driven by a magmatic heat source in a tensional regime.

Jan 1, 1990

By Nickson NM, Lancucki CJ

X-ray diffraction and differential thermal methodshave been used to determine the mineralogy of some clays used by the heavy clay industry in the Adelaide area. A detailed analysis has been made of the mineralogy and. particle size distribution of eighteen samples from beds' in two pits in~the Recent seaiinents in the Adelaide plains, of six white clays.: developed from the weathering of the Adelaide series of `sediments and, of ,four -Recent alluvial clays from a pit in the Mount Lofty ranges south of Adelaide. Structural clay products 'in the Adelaide area are manufactured from mixtures of these clays:, so the mineralogy and particle size distribution have been determined of eighteen clay mixtures used to make red bricks, cream bricks,. facing bricks, pipes and tiles. Knowledge of this mineralogy is important in understanding the ceramic behaviour of the clays.

Jan 1, 1963

The Hellyer deposit, hosted in the Cambrian Mt Read Volcanics, displays features typical of volcanogenic massive sulphide orebodies. These include a well developed stringer zone, metal zonation within the orebody, a polymict volcaniclastic sequence flanking the deposit and a hangingwall alteration plume in overlying basaltic pillow laves.Mapping and core logging is very detailed in order to extract as much data as possible from the deposit and its host rocks. A geological log suitable for direct computer input was adopted shortly after the deposit's discovery.

Jan 1, 1990

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

Some mqre facts and inferences are presented in amplification of a recent paper on the geology of the Kalgoorlie Golden Mile stressing the volcanic origin of its rich gold ores, some of which are considered tobe exhalites. Previously unpublished and largely unmapped pyroclastic features in carbonated and chloritized, but not in amphibolitic, country rock are brought to attention. This applies particularly to the main host, viz. the relatively coarse-grained quartz dolerite greenstone (Q. D. G.), i.e. Golden Mile Dolerite, and gives more credibility to the spatial association of the rich Green Leader and telluride ores with bodies of sediments and tuffites occurring within, or adjacent to, Q. D. G. There may be an intrusive relationship with contiguous mafic amphibolites of doleritic origin, but this is not certain and can only be resolved by morecomprehensive mapping than in the past. Volcanic features have always been recognized in CalC Schist, i.e. Paringa Basalt, more so recently in the shape of coarse volcanic breccia.Iu the subsequent deformation of the gold ores since their inital emplacement there appears to be a structural parallel with some Canadian base-metal deposits, most of them of volcanogenic origin.

Jan 1, 1976

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

Having provided basic data in the main paper I would now like to move on to discuss these areas in broader terms and to examine the various coalfields in terms of their tectonic setting and depositional environment and ultimately to make some brief comments on the factors which may have controlled deposition.

Jan 1, 1975

By Hebblewhite B, Humphreys D

An experimental mining project has been carried out in the Collie Basin to demonstrate the safe operation of total extraction mining techniques in the underground mines of the basin. To achieve this, it was necessary to design and install a means of controlling or removing groundwater so that goafing of the overlying strata could be safely achieved as part of the mining operation. The site chosen for the experiment was a triangular panel adjacent to Western No 6 (WD6) underground mine, which includes the 3 to 4 m thick Wyvern Seam beneath 130 to 180 m of overburden. The test area abuts a major fault on the downdip side. The overburden and underburden sequences include several horizons of permeable sandstones which form major aquifers. Water problems have long been recognized in all underground mines in the Collie Basin, and have previously prevented the successful application of total extraction mining. Following extensive hydrological investigations, dewatering and depressurization systems were designed to dewater the immediate roof aquifers and to depressurize aquifers higher in the sequence and in the floor. This would enable stable roof conditions to develop and controlled goafing to be achieved. The roof dewatering/depressurization procedure involved a combination of in-mine vertical roof drainage holes and conventional dewatering bores constructed from the ground surface above the mining trial area. The dewatering system was installed and operated for 29 months before the commencement of mining. Mining was eventually successfully completed in two trial panels using a retreat Wongawilli extraction system using bridge conveyors and continuous miners. Water inflow into the mine workings was channelled to a constructed sump area at the lowermost corner of the panel and pumped to the surface via vertical sump bores. The dewatering and depressurization measures adopted were successful in permitting the first controlled and systematic total extraction recovery of coal from the Collie Basin. This trial mining exercise demonstrated the potential for increasing substantially the recovery of coal from the Collie Basin, where previously recovery rates of around 30 percent from underground mining were commonplace, using only bord and pillar methods.

Jan 1, 1988

By Knijnikov M, Cameron D

Coal Quality management and the control of the flow of coal through complex mining preparation and transport phases of standard mining operations has assumed greater importance over recent years.

Jan 1, 1998

The invitation to speak today was in the form of a single sentence instruction: How does your company run and how do you communicate from top to bottom? It looks like I'll have to let you into our little secret. The team at Croesus know what works for us but we've never talked about it with others - least of all presented it at a conference such as this. In fact we tend to avoid the jargon normally associated with Best Practice or TQM, however in our own way, each of our staff are 100 per cent loyal to our company's aim to maintain and strengthen our commercial success. Just how we achieve this at Croesus is the subject of this presentation today, but first a little history. My dear old grandfather arrived in Kalgoorlie, as a mining engineer 100 years ago. Do you think he would have chuckled if someone suggested to him that a hundred years later we would just be starting to understand Kalgoorlie's geological mysteries? Well, here we are 100 years later and Croesus Mining is fortunate to be part of a generation now realising the true potential of Kalgoorlie's Goldfields. This provides us with a very fertile field in which to sow the seeds we can obtain from the World's Best Practice in Mining and Processing. With each new mineral deposit being discovered, old theories are being exploded. Each new deposit has a personality of its own, leading to some belated pioneering theories of where to drill next, and how to reduce internal costs so that we can win the war against constantly increasing external costs. What we have now and what the old timers didn't have is a huge database of geological input spanning several gold booms and a couple of nickel booms. My only interest in history is to pick up the points that may help us for our future. This is what we are doing in our company which is something of a David, in the David to Goliath range of mining companies in Australia. As a humbling thought; of the 115 164 tonnes of gold that the world's mines have produced throughout history, four tonnes have been produced by Croesus Mining. That's equivalent to 0.003 per cent of the total world's gold production. In the past financial year we achieved a dividend yield of five per cent. To put this into perspective, that's over twice the dividend yield of BHP, Australia's largest company. As we are somewhat less known than BHP, let me spend a few moments giving some particulars of our company's background.

Jan 1, 1995

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

I WISH to express to the members of the Institute my sincere appreciation of the distinction which they have conferred upon me by again making me their president. It also gives me great pleasure to once more welcome the Institute to Mount Lyell.Since your last visit certain improvements in plant have been made, which I trust you will have found interesting, and which show that, though located in a remote corner of the world, we are abreast of the times.The opportunities which a recent lengthy trip to America has given me to observe the degree of interest which our local smelting practice continues to arouse in metallurgical circles make it seem appropriate that I should take advantage of your visit to lay before you some detailed information on the more practical features of pyrite smelting, particularly as carried out at Mount Lyell. There are only a few places in the world where the method is now being practised in approximate purity-only about half...

Jan 1, 1915

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011