Search Documents

By N M. Rana, A Take, N Ghahramani, S McDougall, S G. Evans

A critical issue associated with mining operations has been the stability of tailings impoundments. Some breach events have produced catastrophic tailings flows that have caused significant economic damage, mass casualties and long-lasting environmental impact in the downstream environment. This paper reports independently estimated values of runout distance, inundation area and fahrboschung of 16 tailings flows. The adopted methodology involves the geospatial analysis of satellite and aerial imagery to classify each tailings flow into a primary impact zone (Zone 1: main overland flow) and a secondary impact zone (Zone 2: along-creek diluted flow) to characterise runout. Only Zone 1 runout values are reported herein given the greater significance in relation to downstream impact. The fahrboschung is calculated using elevation data from global 30 m digital elevation models (DEMs) and source literature. The results show that all the selected tailings flows travelled long distances (2.4 km to 98.5 km) and inundated large areas (0.35 km2 to 27.0 km2) over very low fahrboschung values (0.04° to 4.8°). This indicates very high flow mobility that is largely governed by the high water content sourced from interstitial waters and, in many cases, supernatant ponds. Scatter plots display poor correlations owing to the complexity and variability in travel path characteristics (confinement, slope angle and obstructions) and the inherent properties of the flowing mass. The slope angle of the travel path exerts a strong control over the flow velocity which has implications on kinetic energy and downstream geomorphological impact. Mean tailings flow velocities may range from ~6 m/s on near-flat, open terrain to over 30 m/s in relatively steeper, channelised travel paths, indicating that tailings flows fall within the extremely rapid and high mobility spectrum of global mass movements. The presented work forms an inceptive part of the CanBreach tailings project, a major component of which is to develop a comprehensive database of case histories to examine the role of geotechnics, failure modes and downstream terrains in influencing tailings flow behaviour.

Jul 1, 2021

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By S Thomas, S Ricketts, R Hassell

Northern Star Resources (NSR) operates several operations utilising narrow vein stoping operations in the Kundana area. Stope dilution performance is variable across these operations, with unplanned dilution reducing individual stope economic viability, increasing risk to personnel and machinery operating in and around the stope and delaying the overall stoping sequence. Technical investigations were undertaken to objectively understand the variables which had the largest impact on stope performance and then use the findings to help develop mining strategies to reduce dilution. A stope reconciliation process was developed to compile key stope performance information such as stope design parameters, geotechnical and drill and blast factors. These were compared against the measured dilution. Production targets necessitated a high turnover of stopes in the operations, and hence a requirement for an expeditious process and mine design software with automated tools. The output of these results, together with numerical variables from geological, geotechnical and drill and blast data were analysed via multivariate regression. The analysis identified the factors with the greatest influence over stope dilution, and a forecast model was consequently created. Confidence was gained in the model when the subsequent stopes performed in line with prediction. Different drill and blast designs were subsequently trialled and found to reduce dilution. The model was then updated with the new practices, facilitating further regression analysis to identify revised key controlling factors. The subsequent production results however, displayed a poor correlation with the prediction from the revised model. Inconsistencies in drill and blast designs and execution were identified as key factors in the dilution performance. This was an important finding as the correct implementation of the design is critical and this has become a key focus for future stoping. Overall the technique presents an objective process to identify causal factors of stope dilution resulting in improved economic metrics for stope production. The process will be applied to other similar Northern Star operations.

Mar 15, 2021

By A Hutton, C Dick, D Fletcher

Mine and facility closure planning is a dynamic and rapidly evolving landscape. In this landscape, mining companies and industry consultants are generally good at estimating the associated earthworks and rehabilitation costs, because it is æcore businessÆ. Through our extensive work in mine closure, we have found that the safe and cost-effective demolition of mining related infrastructure is often grossly underestimated. Or alternately, it is simply assumed that the returns on scrap steel and the sale of re-usable plant will cover the related costs. With fluctuating steel prices and no guaranteed buyer for the assets, the estimated monetary return is often unreliable and in many cases unrealistic. On this basis this logic is fundamentally flawed. We have found that on most occasions this has meant that closure cost estimates fall well short of what the actual costs are to close the mine.GSSE and Liberty Industrial have worked on over 60 mine closure projects in Australia and overseas of varying scales and across a range of commodity types. An evaluation of these projects has shown that costs associated with the safe demolition and removal of a mining related infrastructure is in the order of 20 - 30 per cent of the total cost at closure. We believe it is one of the top three risk areas associated with mine closure planning and cost estimation, alongside bulk earthworks and the capping of tailings and waste rock storage facilities.Our paper uses examples from recent projects to demonstrate all aspects outlined above. We have also endeavoured to address the following key points related to the demolition and removal of mining related infrastructure:If companies fail to plan appropriately, complicating factors such as contamination, hazardous materials, mobilisation/demobilisation, geographical location, decommissioning standards, site constraints and weather, can add considerable costs to the project and result in variations for the demolition contractor.Closure planning often assumes infrastructure that is no longer required can be utilised by a third party and/or the new land holder. We intend to show that unless adequate consultation and planning is undertaken, this is not beneficial to the mining company, the environment, or the local community.CITATION:Fletcher, D, Hutton, A and Dick, C, 2012. The æsmoking gunÆ of detailed mine closure cost over-run - A review using case studies of the real costs associated with the demolition and removal of infrastructure in mine closure, in Proceedings Life-of-Mine 2012 , pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J Jackson, K Nguyen, A Nguyen, E Manlapig

"With the recent advancement in drill core imaging systems, a large volume of high resolution drill core images can now be rapidly collected and mineralogically classified. This paper introduces a novel semi-automated method for rapid prediction of process engineering parameters from this type of image. The aim is to allow for a rapid and low-cost assessment of the ore processing variability within a mineral deposit with a reduced amount of metallurgical test work. This method will see its application primarily in the project evaluation phase, where proper evaluation of the processing variability of the orebody normally requires a prolonged and costly metallurgical test work program. Applying this image-based texture analysis method on the mineralogical classified drill core images, the ores are classified according to their textures. For each engineering parameter, a small number of physical test work is required to produce a data set for training and testing of the predictive model. The paper also presents a case study in which this method has been applied to predict the A*b parameter used in mineral process plant design.CITATION:Nguyen, A, Jackson, J, Nguyen. K and Manlapig, E, 2016. A New Semi-automated Method to Rapidly Evaluate the Processing Variability of the Orebody, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 145–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Fisher WJ

The'treatment of the South Alligator valley uranium ores passed through three phases dictated by economic circumstances during the years 1956- 640 In the first phase high grade ores were treated by hand sorting and wet gravity separation for recovery of high grade concentrate to meet a United States Atomic Energy Commission (U.S.A.E.C.) contract for plus 50 per cent pitchblende concentrates. Secondly tailings from the gravity plant and some high grade ores were trucked to Rum Jungle and sold to the Australian Atomic Energy Comm- ission (A.A.E.C.). Thirdly solvent extraction plants were built at Moline (previously Northern Hercules) by United Uranium N.L. (UOU.N.L.) and at the South Alligator River by South Alligator Uranium N.L. (SOA.U.N.L.). These were the first solvent extraction plants designed in Australia, as earlier plants used the ion exchange process for recovery of uranium oxide. The plants were small, indeed the S.A.U.N.L. 15 ton per day plant was possibly the smallest commercial plant known, but they operated efficiently with good recoveries, and were placed on a care and maintenance'òbasis when contracts were filled. Sulphuric acid was supplied in bulk to both plants by the A.A.E.C. from the 30 ton a day acid plant at Rum Jungle. Gold was recovered as a by product of uranium ore from the Moline plant.

Jan 1, 1968

By D Tanzil, H Jones

Every mine will close! Charting a profitable course through mine operations to acceptable mine completion requires that risk and opportunity management planning of the mine life begin as early as possible in the life cycle. Management targets and metrics are required to identify and navigate the course to successful mine completion based on economic, social and environmental criteria. This paper outlines the application of The Metrics NavigatorÖ principles to the life cycle of a mine site. In general, metrics are required to make key strategic ideas apparent, transforming those ideas into a manageable set of quantitative measures that guide communication and decision making. For example, the chemical industry has established metrics that focus on the life cycle impacts of its products and eco-efficiency of their processes. Other industry sectors have focused attention on workplace and community well-being outcomes. These management metrics are necessarily organisation-specific, aligned to stakeholdersÆ expectations and the strategic outcomes sought, as well as the cause-and-effect relationships underlying key issues. Recently, the Global Environmental Management Initiative (GEMI), a consortium of multi-national companies, developed The Metrics NavigatorÖ. The guidance document provides a structured process for assessing and developing metrics for key environmental, social, and economic issues based on business and stakeholder perspectives. It incorporates best practices learned from the chemical and other industry sectors and has since been applied to develop metrics that guide life cycle strategies. The paper examines how the life cycle of a mine site could benefit from experiences in other industry sectors where sustainability metrics have guided strategy. It considers the potential application of The Metrics NavigatorÖ process to the life cycle of a hypothetical Australian mine site using the processes that have been successful in other industry sectors.

Jan 1, 2009

Problems caused by water discharge from surface mine ventilation shafts can be significant and are usually unforseen. The discharged water is often hyper-saline or acidic and can cause environmental degradation over a wide radius. It can also lead to recurring power pole fires and primary fan breakdowns. A range of solutions to the water discharge problem has been implemented in many Australian mines. In most cases the solutions have been ad hoc, with the overall cost and effectiveness varying tremendously. This paper reviews and contrasts the practicality and effectiveness of the various available remedial options.

Jan 1, 2002

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By T D. H McGrath, G Wardell-Johnson, E A. Oraby, W Staunton, A R. Bax, J J. Eksteen

"Gold ores often show significant inter-domain variation with respect to the gravity recoverable gold (GRG) content and the leach behaviour of the non-GRG component. Liberation assessment is extremely difficult for gold due to its malleability and the high sampling errors and poor test reproducibility resulting from gold’s high specific gravity and the low metal concentrations that occur in most gold ores. The use of microscopic techniques for the liberation assessment of gold is also impractical due to the high number of sampling errors and high cost of analysis.Curtin University’s Gold Technology Group has developed an online carbon-in-pulp/carbon-in-leach (CIP/CIL) simulation model called SIMCIL, which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach, which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The ILLM characterisation methodology, test work data analysis, interpretation and application of the ILLM test work data are discussed.CITATION:Bax, A R, McGrath, T D H, Eksteen, J J, Staunton, W, Oraby, E A, and Wardell-Johnson, G, 2016. An Integrated Liberation-leach Model and Ore Characterisation Procedure for Gold Ores, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T W. C Stambolie

Coalmines, like any other mine, generally involve the classic three-staged approach to mining studies; namely concept, pre-feasibility study (PFS) and feasibility studies (Cusworth, 2012). Subsequent to these studies, and in instances parallel to these studies, the commitment to an environmental impact statement (EIS) is made in order to secure both state and federal development consent. In recent times, the sentiment to both mining and coal is changing whereby the traditional approaches to mine planning and economic evaluation is complicated by evolving environmental legislation, expectations and time frames. It is all too common to take shortcuts in the development of projects in order to create the perception of cost savings and expediting the delivery timeline. Atkins (2016) points out that: boards of so many small to mid-tier mining companies, and a few majors, focus on relentless project delivery too early in the project process, with so little time and effort applied to risk analysis and option development. Unforeseen risks can cost any timeline or budget far more than the effort required assessing and mitigating these. The ultimate risk to any feasible coal project is that of environmental approval and achieving development consent.CITATION:Stambolie, T W C, 2016. A black canvas – planning a greenfield coalmine in New South Wales, in Proceedings Life-of-Mine 2016 Conference , pp 31–35 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Wheeler

The benefits of fine size separation in magnetite concentration are detailed focusing on published research from various iron ore producers. Basic principles of fine sizing and advancements in screening technology are addressed. A chronological review of research is used to show the evolution of fine sizing applications in the industry, starting with studies that demonstrated the benefit of using fine screens to produce consistent lower silica concentrates, followed by improvements in fine sizing equipment that have made effi cient screen classification in ball mill circuits practical. Case studies are used to demonstrate how positive sizing with screens can be used to significantly shift concentrate ‘grind/grade’ relationships.

Jul 11, 2011

By A Tawadrous, B Wheeler, D S. Preece, S A. Silling

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Moving rock with explosives rather than mechanical equipment can improve mining efficiency. Such is the case with coalmine cast blasting. Controlling and directing rock movement through explosive deck delay timing can greatly improve ore recovery by segregating ore and waste. In both cases, understanding, predicting and controlling heave is an important element of successful blasting.Computer programs for predicting 2D blasting-induced heave have been used in mining for decades, helping to drive the innovation of new and more efficient mining methods, ie cast blasting. The past few years have seen the advent of 3D distinct element modelling of blast-induced heave. This is an important advancement because most blasting situations are three-dimensional in nature, especially when controlling the direction and intensity of rock movement through explosive deck delay timing.This paper documents the first full-scale blasting simulations in 3D with distinct element models that include hundreds of blastholes and in excess of a million particles, made possible with parallel processing. Surface mineral blasting is the focus of this study which treats the effect of blasthole delay timing on ore recovery. Ore waste and dilution resulting from typical row-on-row delay timing will be demonstrated. Also demonstrated will be the ore recovery possible with delay timing designs that significantly enhance ore/waste segregation. This type of high fidelity modelling and the use of electronic detonators makes possible the sculpting of rock blasting muck into separate piles of ore and waste.CITATION:Preece, D S, Tawadrous, A, Silling, S A and Wheeler, B, 2015. Modelling full-scale blast heave with three-dimensional distinct elements and parallel processing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 127–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Reconciliation involves the collection of tonnage, grade (quality) and contained metal (product) data from disparate and hopefully independent sources. Examples are exploration data, production sampling data from blastholes or drawpoints, and process plant data. These data may be compared by means of ratios (factors). The F1 factor usually relates short-term (ore control) model tonnages, grades and metal content to ore reserves depleted. The F2 factor usually relates received-at-mill tonnages, grades and metal content to delivered-to-mill = production tonnages, grade and metal content. The F3 factor is F1 × F2 and enables a comparison of a mineÆs ability to recover the tonnage, grade and metal content estimated in ore reserves. The F1 factor measures the accuracy of orebody knowledge in the ore reserves to the demarcation of ore and waste by ore control (short-term model). The F1 factor may be used to check and calibrate the selectivity of mineral resource models and/or planned dilution assumed in transfer from mineral resources to ore reserves. The F2 factor enables a check on unplanned dilution entering the ore stream between ore control and the mill. Using the factors it is possible to calculate a monetary value on improvements in the accuracy of orebody knowledge, selectivity and the effects of dilution and ore loss. Reconciliation should be an implicit part of the mining process, and reconciliation targets should be a key performance indicator for well-run mines.

Sep 26, 2011

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J A. van Niekerk, J G. Jardine, J W. Olivier

The Runruno Gold Project is located on the island of Luzon, approximately 200 miles north of Manilla in the Philippines. The mine is an open cut operation and uses the proven BIOX® and carbon-in-leach (CIL) processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces (Moz) of gold, and the operation will produce 96 700 oz of gold per annum over a mine life of 10.4 years. The BIOX circuit is designed to treat 140 000 t/y of concentrate with a design capacity of 404 t/d of concentrate at a design sulfide sulfur grade of 17% S2-.The Runruno BIOX Plant is the first application of the Outotec BIOX Generation III design principles, focussing on ease of operation and maintainability. During development and implementation, the project team focussed on identifying opportunities to optimise the capital efficiency while not compromising on the operability or overall efficiency of the process or the equipment. The BIOX plant also incorporates the latest developments in the design of the BIOX agitators for more efficient mixing and gas dispersion. This paper will discuss some of the critical aspects and decisions taken during the development and implementation of the BIOX Process at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX design principles. CITATION:van Niekerk, J A, Olivier, J W and Jardine, J G, 2017. Implementation of the BIOX® process at the Runruno Gold project, in Proceedings MetPlant 2017, pp 218–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By C E. Gawith

The Waihi underground mining operation currently mines epithermal veins ranging from two metres up to ten metres in width using a ‘Modified Avoca’ stoping method. This method consists of longhole bench stope mining at 15m to 18m sublevel spacing. The bulk of production drilling and blasting is top down with the extraction length of a typical stope panel nominally being 18m to 20m along strike. A stope panel is usually taken in two blasting cycles followed by the remote bogging of the stope ore. The panel is backfilled in-cycle using unconsolidated waste rock material which is tipped into the void from the upper level using a Caterpillar R2900 or R1700 sized underground loader. The underground mine first commenced production in 2008 and up until 2016, as was typical of many open stope mining operations at the time, an underground loader was used to place a waste rock bund at the top brow of the open stope. This rock bund was the principal means of protecting people and equipment from this hazard. In 2016 there was a fatality at the mine when a loader that had been tasked with building this rock bund fell into the stope void. Immediately post incident all mining and processing operations were suspended for a week to allow colleagues to grieve, to observe cultural protocols and to begin the investigation into this event. During this period senior operators, supervisory and technical staff developed an innovative system which used steel bollards to protect this open edge. With development over the following months this bollard system has eliminated this hazard from the Waihi underground mine.

Mar 15, 2021