Search Documents

By T R. Gibbons, I Grayand

Geotechnically massive strata may lead to a host of problems during longwall mining. These include windblast on initial goaf fall, sudden loadings on powered supports, periodic weightings, fractures that may propagate to surface, and extreme subsidence problems. It is essential to identify these problems prior to mining and to appropriately deal with them. The problem is essentially that the rock mass does not breakup evenly and when it does so it tends to produce large blocks which may suddenly move. The rock types that produce these problems tend to be massive sandstones, massive siltstones and sometimes igneous sills. The fundamental problem with these is that they do not breakup readily. This is because the ratio of stress they are subject to compared to their strength is low. Thus, the shallower mines with lower stresses are more subject to this problem than deep highly stressed ones with similar strength rock.

Nov 29, 2022

By H J. J Boshoff, A J. Karrasch

Mine planners frequently face the challenge of mitigating the impact of climatic events on mining operations, such as floods and droughts. Specific water management infrastructure can be implemented to meet operational requirements in response to these events. However, the effect of flood protection, for instance, may reduce the resilience of the site to drought. The probability and duration of unfavourable climate sequences significantly influences the net present value (NPV) of implementing specific water management infrastructure.Good life-of-mine planning will consider the incremental development of the project, and provide staged development plans. Water management infrastructure and the timing of implementation are facets of this process.CITATION:Boshoff, H J J and Karrasch, A J, 2016. A decision-making framework for water supply and flood protection options in net present value terms, in Proceedings Life-of-Mine 2016 Conference , pp 196–199 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R L. Grogan

Regulators of deep-sea mining projects are becoming increasingly hesitant about the concept of adaptive management as a tool to facilitate compliance and continuous improvement. Adaptive management is a relevant and useful instrument to ensure that the mine plan is successfully implemented throughout the life of mine, in parallel with optimum environmental performance and compliance.CITATION:Grogan, R L, 2018. Adaptive management in deep sea mining – looking like you know what you’re doing when it’s never been done before, in Proceedings Life-of-Mine 2018, pp 20–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By X Zhang, Z Guang, R Lin

To improve the existing process of a large-scale scheelite concentrator in Jiangxi Province, this paper presents an advanced process æselective flotation of copper and flotation desulfurisation û rougher flotation of scheelite û heating-stirring and cleaning of rougher concentrate at normal temperature without reagent removalÆ. The test work was conducted on an ore sample containing 0.75 per cent tungsten (WO3), and the following technical indices were obtained: 1.03 per cent of the scheelite concentrate yield, 65.37 per cent of the concentrate grade and 86.31 per cent of WO3 recovery, indicating that the study achieved the objective of improving the tungsten recovery. The technical key of this process is to employ combined regulators and direct flotation of the slurry after being heated, which not only assured the technical indicators of beneficiation but also simplified the process.

Jan 1, 2008

By S Szylkarski, D N. Graham

In mining, water management is an operational necessity, requiring planning and detailed engineering, as well as risk assessment. Yet, the hydrology of streams and aquifers typically extends well beyond the boundaries of mine operations and intersect with environmental and social values. Mine managers often plan, design and assess the impact of water management activities (such as dewatering, excess water disposal and flood management) with a mine site or process specific focus. The challenge is that the impacts are spatial, long-term and complex – and may be cumulative across multiple mine sites. Further, there is usually little consideration of the feedbacks and interactions between surface water, groundwater and catchment hydrology. Failure to understand these processes can lead to poor decisions and increased costs. This presentation outlines an approach to simulating integrated hydrology in mining catchments that addresses the shortcomings of traditional modelling techniques.CITATION:Graham, D N and Szylkarski, S, 2016. Simulating integrated hydrology in mining catchments from planning to closure, in Proceedings Life-of-Mine 2016 Conference, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A He, J Li, J Pan, J Clout

The removal of sulfur from SO2 containing flue gas is improved by adsorbing SO2 into solution with manganese ions as catalyser, however, burnt lime slurry has to be added to modify solution pH and the CaSO3 by-product is of low economic value. In this paper a novel one step process for simultaneous manganese leaching-desulfurisation of flue gas is presented. An investigation of the effect of process parameters included flow rate and SO2 concentration in flue gas, adsorbing time, solution to solid mass ratio, leaching time, and their impact on the oxidation and removal of SO2 from flue gas. The catalysing mechanism of manganese ions on the oxidation and SO2 removal was demonstrated by calculation of the species originating from manganese ions and SO2 in the solution according to solution chemistry. SO2 removal in the adsorbing solution took place at pH 5 - 6, where manganese ions dominantly occurred as Mn2+, and the chain reactions for oxidation of SO2 starting from HSO3- were improved by the presence of Mn2+. SO2 bearing flue gas was effectively desulfurised by leaching rhodochrosite (MnCO3), with desulfurisation of the flue gas and modifying the solution pH being achieved simultaneously, and MnSO4 of high economic value recovered from the leachate. 85 per cent manganese leaching and over 70 per cent desulfurisation of the SO2-bearing flue gas were achieved with only one adsorption stage under optimum conditions.

Jan 1, 2004

A flow sheet has been developed to treat a high tonnage highly preg-robbing gold ore. The ore is low grade and fine grained with a high proportion of very fi ne free gold. The key components of the flow sheet include gravity, flotation, intensive cyanidation with direct electrowinning, and carbon-in-leach of the flotation concentrate. The circuit produces a low overall mass pull to concentrate allowing economic intensive treatment of large tonnage low-grade material. Efficient recovery of fine gravity gold using a Falcon concentrator in both the milling and flotation circuits, and subsequent intensive cyanidation in a Gekko InLine Leach Reactor (ILR) is critical to the process with over 70 per cent gold recovery expected in this circuit. Grind size control was also found to be important in controlling the activity of the preg-robbers in the carbon in leach circuit and also in the solid liquid separation performance. Tests at the large-scale demonstration plant have been conducted to demonstrate the effectiveness of this flow sheet. A large low-grade deposit is currently under development with the aim of developing a 10 Mt/a treatment plant with the subsequent addition of equivalent sized process lines in multiples of 10 Mt/a. The economic development of this orebody is critically dependant on understanding and exploiting the properties of the ore. In particular it is critical to minimise the effect of preg-robbers by recovering free gold with Falcon concentrators and InLine Leach Reactors. Recovery of the remaining gold by flotation into a small mass yield allows this fraction of gold to be treated by CIL leaching utilising high carbon levels. It is critical is to ensure operation at the optimal grind size to maximise liberation of the free gold and minimise pregrobber activity. The ore has been identified as preg-robbing with low recoveries obtained if treated using conventional cyanidation and carbon absorption. The mineralogy consists of predominantly fi ne grained free gold with minor sulfides including pyrite and arsenopyrite. With conventional cyanide leaching in the absence of carbon, gold recovery is less than 50 per cent. Direct cyanide leaching of the ore in the presence of activated carbon results in an improved but still uneconomic gold recovery. The gravity recoverable gold (GRG - as defined by Andre La Plante) content of the ore has been measured to be 70 per cent to 85 per cent in various tests with liberation grind size of approximately 106 ¦m. This indicates gold is predominantly free and suitable for recovery by batch centrifugal concentrators into a low mass yield. This property of the ore presents the opportunity to maximise the recovery of gold by separating it from the majority of the preg-robbers prior to leaching. Due to the very fine gold particle sizes and the necessity to maximise recovery of this fine fraction Falcon concentrators were selected for the duty, with their proven high recoveries at very fine gold sizes. The gravity recovery in the milling circuit is designed to be in the range 55 to 65 per cent. This has been achieved in the existing pilot plant using a Falcon operating on ball mill discharge within the mill recirculating load. Intensive leaching in an InLine Leach Reactor is essential to recover the gold from the gravity concentrates. Tabling is not a preferred option since recovery is lower than intensive cyanidation and any gold losses to table tails will report to CIL where recovery is reduced by the presence of preg-robbers. Furthermore, tabling recovery from the gravity concentrates is particularly poor due to the fine particle size of the free gold. ILR recoveries of 98 per cent were demonstrated in the pilot plant using an ILR100BA and leach conditions were investigated in the lab using pilot plant generated Falcon concentrate. Recovery of gold from the pregnant solution was achieved with direct electrowinning at pilot and efficiency and sizing parameters were determined at lab scale. To further increase free gold recovery Falcon concentrators will be installed in the flotation circuit. Location of the Falcons in the circuit is not finalised but installation on the rougher concentrate stream is favoured since it will allow multiple pass recovery. This is expected to recovery a further ten to 20 per cent of the gold, as indicated by lab tests on pilot plant generated material. The gravity concentrate from the flotation circuit will also be leached using InLine Leach Reactors. Initial intensive cyanidation tests carried out on lab generated flotation concentrates indicated higher recoveries than CIL can be obtained even though the concentrates contain significant levels of preg-robbing material. This can be explained by the high cyanide, high pH leaching conditions used in the ILR which alters the absorption equilibrium of the preg-robbers. Further optimisation of the leach conditions will be undertaken once more concentrate becomes available. Recovery of the remaining gold content is achieved by flotation into a small mass yield, however the preg-robbers are also recovered into this concentrate. Due to the presence of the preg-robbers gold leaching must be carried out in the presence of high levels of activated carbon in a CIL system. The recovery has been shown to be strongly dependant on the carbon loading and the concentrate particle size. The carbon competes against the preg-robbers for dissolved gold while excessive grinding increases the surface area and activity of the preg-robbers. This has been demonstrated in test work however the economic optimum leaching conditions and carbon loading have yet to be determined. The grind size is critical to the economics of the project, not only due to its effect on gold recovery but also due to its effect on the major operating and capital costs at both the front and back end of the process. It is critical to grind enough to obtain both gravity free gold and flotation liberation at low mass yields however over-grinding results in large increases in mill size and power at the front end and filtration or thickening costs at the tails. Because these unit operations treat essentially all the plant feed even small changes can result in major impacts on project economics. The viability of this project is greatly enhanced by the high recovery of gold into a small mass yield. In particular the production and intensive leaching of the free gold gravity concentrates will allow over 70 per cent of the gold to be recovered efficiently with minimal impact from preg-robbers. By using flotation the mass of the remaining fine preg-robber contaminated material, to be leached in CIL, is greatly reduced allowing this difficult material to be economically treated. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By R Shaw

There are many small to medium carbonate hosted complex zinc containing deposits where the zinc is not economically recoverable either as concentrate or metal. High grade (>20% Zn) run of mine ore can be processed but even this material gives relatively poor returns. Considerable effort has gone into developing new technology for either upgrading the ore and/or recovering zinc metal hydrometallurgically but there has been limited success. Minetometal has developed a process capable of economically treating these deposits to give marketable lead and zinc products. This paper reviews alternative processes for these ores and gives a detailed description of the Minetometal Process. CITATION: Shaw, R, 2018. Processing carbonate hosted zinc-lead ores, in Proceedings Complex Orebodies Conference 2018, pp 130–131 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J L. Merritt

The mining industry seeks to engage with and respond to stakeholders through open consultation processes during the various phases of a mining project (Department of Industry, Tourism and Resources, 2006). Two Australian Coal Association Research Program (ACARP) funded projects conducted in the Bowen Basin coalfields in Central Queensland investigated the use of a stakeholder panel for the evaluation of mine site rehabilitation. The panel members were drawn from the local and regional area, and represented neighbouring landholders, traditional owners, AgForce, local government, conservation groups and non-governmental organisations (NGOs) such as Greening Australia and the Fitzroy Basin Association. The approach of utilising stakeholders to establish rehabilitation criteria was proposed as an alternative to the established practice of assessing rehabilitated areas against a suite of quantitative completion criteria; eg >70 per cent vegetative ground cover or <5 t/ha/a soil loss. The basis of this approach recognises the reality that the definition of completion criteria has proved problematic over the last 40 years with no broad consensus reached on the suite, let alone the metrics; eg the exact cover level that will benchmark acceptance of the mine site rehabilitation.CITATION:Merritt, J L, 2016. Zooming out – learning to see rehabilitation through stakeholders’ eyes, in Proceedings Life-of-Mine 2016 Conference, pp 163–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

This paper describes the oil engihe plant owned and operated by Gold Mines .of Kalgoorlie Limited, and gives some details of installation, operational, and maintenance experiences which have arisen during the years of service, the last 5 years of which have been under the writer's control. Nos. 1, 2, 3 and 4 alternator units have run 50,276, 48,006, 49,677 and 25,930 hours respectively, and much knowledge has been obtained of their performances and faults. During the war years, it has not been easy to obtain spare parts; this, coupled with the loss of No. 4: alternator unit to the Commonwealth Government, made operation and maintenance a very difficult problem.All engines are of the enclosed vertical, single acting, 4-stroke cycle, airless injection type.The electrical power plant originally consisted of four 6-cylinder Belliss & Morcom heavy oil engines, direct coupled to Bruce Peebles alternators, running at 375 r.p.m., and generating 3-phase electric power at 3,300 volts, 50 cycles.No. 1 unit, installed in 1936, is a 6-cylinder 450 b.h.p. standard 12A Belliss & Morcom heavy oil engine, direct coupled to 280 kw. 0.8 p.f. alternator. The remaining three units are 6-cylinder, 660 b.h.p., lSA oil cooled piston type Belliss & Morcom heavy oil engines, direct coupled to 410 kw. 0.8 p.f. alternators, making a total capacity of 1,510 kw.No. 4"alternator. unit, an 18A Bellis.& Morcom set, was taken over by the Commonwealth Government in June 1943.

Jan 1, 1945

The ore mined from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangano-calcite and apatite. The silver content of the ore occurs in three minerals tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations.Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14 - 18 per cent lead; 3.0 - 4.5 oz silver per tonne, and 9.5 - 12.0 per cent zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from six to eight per cent lead, 1.5 oz silver per ton, 18 - 25 per cent zinc with a siliceous gangue. The common Lead Lode gangue minerals, calcite, rhodonite, bustamite - are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce:1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc concentrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufftcient granular material to be utilised as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5000 tons of crude ore per week. This plant, which operated until January 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of jigging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each consisting of two 5 ft diameter by 10ft long tube mills loaded with flint pebbles working in closed circuit with four 3 ft diameter by 3 ft wide revolving screens covered with 22mesh Toncap woven wire screen with 0.57 mm opening. Each section carried a circulating load of 28.3 tons per hour for a jig.

Jan 1, 1994

By A Harris, L Balzan

Accurate measurements of the moisture content of iron ore have increasing importance in modern mining operations. Knowledge of the moisture content allows process control actions to be carried out to ensure that the moisture is within prescribed limits, whether this is ensuring sufficient moisture to be above the dust extinction limit or that the moisture level is below the transportable moisture limit for sea shipments. Additionally, controlling moisture within desired limits can allow for greater throughput of iron ore by limiting the amount of water transported. There are a range of options available for operators wishing to obtain moisture data, though there are few demonstrated and proven devices that are able to provide real-time analysis of the full bed-depth of material. Scantech’s through-belt moisture systems are able to accurately analyse the full bed-depth of conveyed iron ore in real time using its unique microwave transmission technology, providing valuable data for operators. Recent advances in these systems have overcome errors associated with the highly attenuating nature of iron ore, particularly for large conveyor belts and deep ore. Furthermore, analysis of different ore mineralogy and its effect on the accuracy of moisture analysis has been examined and quantified. This paper discusses some of these recent results, demonstrating achievable accuracies in spite of changing ore mineralogy. Scope for future work is also briefly discussed, concluding the paper.CITATION:Balzan, L and Harris, A, 2015. Real-time through-belt moisture analysis for iron ore, in Proceedings Iron Ore 2015, pp 539–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Working thick coal seams in Poland is a very serious problem. Nearly 40 per cent of all coal is extracted from seams more than 3 m. thick. In absolute figures this represents about 70 million tons of coal per year. Working seams with thicknesses up to 3.5 m. does not present, at present, major difficul- ties. Working thicker seams calls for a steady improvement in order to increase the degree of utilization of the deposit and to enlarge the concentration of output. The problem is sometimes more difficult because, in many cases, the seams are worked under protected surface structures which compels the mines to use hydraulic stowing with all its advantages and disadvantages. Rock burst hazard, the control of which is the basic problem hindering the mining, is a further problem. The mining systems used in Poland are adapted to these natural and technical conditions.

Jan 1, 1976

By C Sylvestre

For the last 50 years, traditional safety management has improved safety performance by: • Fixing the environment (eliminating the hazard). • Improving the system (more/less rules, procedures etc). • Making safety more conscious (more/better interactions about the importance of safety). Although these approaches certainly have merit, and may be part of an overall solution, they are not enough to prevent many modern-day incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

Robe River Iron Associates (RRIA or Robe) is widely regarded as the worldÆs most cost-effective, consistent and reliable supplier of iron ore. It has been in operation since 1972 and globally is the fourth largest seaborne trader in iron ore exporting 25.5 million tonnes of -9.5 mm sinter fines and 4.5 million tonnes of pisolite lump (-31.5 +6.3 mm) during 1999. Robe is a joint venture that controls major iron ore resources in the Pilbara region of Western Australia. ItÆs participants are North Limited with an interest of 53 per cent (65 per cent including minority interests) and Japanese companies Mitsui (33 per cent), Nippon Steel Australia (10.5 per cent) and Sumitomo Metal Australia (3.5 per cent). Robe River Mining Co Pty Ltd manages the project which is a subsidiary of North Limited and Mitsui.

Jan 1, 2000

Declining from surface provides access, haulageway, ventilation and provision for ser- vices for stoping and development. Three boom jumbos and 3.8 m3 capacity diesel loaders are used in decline development, the majority of which is driven at a gradient of 1 in 9. Primary ventilation is drawn from the mine through raisebored airways and high pressure contra rotating fans provide secondary ventil- ation. To meet schedules a special decline crew was formed on similar lines to a mining con- tractor. The basis of payment for the mining party was changed and the net effect was to accelerate development. Ground conditions demand constant support and this is achieved with chemical anchor rock bolts, multistrand grouted bolts and shotcrete. Major local shear zones are encountered and when they are to be driven through, a combina- tion of the above methods, involving a spiling technique, is used.

Jan 1, 1977

Rio Tinto Iron Ore is currently working towards finalising comprehensive Native Title land access agreements, which cover all of the current eleven mines and infrastructure owned and operated by the company in Western Australia's Pilbara region. Critically, the agreements represent a mutual commitment to a long-term relationship and address many areas of concern by promoting indigenous enterprise, well-being and regional development opportunities. Our objectives in the process are to obtain the informed consent of the traditional owners for our Pilbara expansions while providing benefits to them in a way which provides lasting and substantial improvements to health, education, housing and real jobs in the mainstream economy.   To facilitate the agreement negotiations, Rio Tinto Iron Ore (RTIO) proceeded in 2005 to research and design a specific strategy around Aboriginal relations and local community engagement in the Pilbara. Wherever we operate, Rio Tinto follows a fairly simple formula in working with communities, which is comprehensively aligned to local context.   This presentation provides an overview of Rio Tinto Iron Ore's community engagement strategy in Western Australia's Pilbara region. It will also explore the establishment of regional standards on employment, business development and contracting that have been developed to ensure Indigenous people are engaged in the development of their region and are able to contribute to supporting the growth and development of mining in the area with the expectation that there is prosperity for all. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By Abdurazakov A, Avrakhov A, Solozhenkin P

The flotation properties of acetic acids modified by xanthic and dithiocarbamic fragment in regards to copper and ferrous minerals and their noble metal containing ores have been investigated. The effectiveness of the co-using of these reagents with xanthates and dithiocarbamates has been shown, ie using of proposed reagent regimes for the flotation of Au-containing ores increases gold recovery by 4.2 - 4.7 per cent, and in the case of flotation of copper Re-containing ores copper recovery increases by 3.3 per cent, rhenium recovery - by 15.5 per cent. The mechanism of the action of these reagents has been explained by the data of UV and ESR-investigations of their sorption on mineral surface. The information on structure and properties of co-ordination compounds of some metals with (Diethyldithiocarbamato) acetic acid were used also for the explanation of flotation mechanism.

Jan 1, 1993