Search Documents

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

By C O. Gomez

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

The longwall system with caving is the most common mining system in Polish Collieries and the extraction is carried out simultaneously on several levels and in different seams. The extent and diversity of the methane hazard occurring is strictly connected to the specific geological and gas conditions as well as to the applied mining methods. Taking these factors into consideration the following methane drainage methods are applied as additional means of combatting the methane hazard in Polish gassy coal mines: 1. predrainage by means of boreholes drilled from the surface, 2. predrainage from stone drivages and devel- opment workings, 3. degasification of coal extraction workings, and 4. degasification of sealed-off areas/old goaves. Predrainage gave satisfactory results when holes were drilled from the surface or from underground workings, but only to depths to 300 m. It was necessary to adapt methane drain- age methods to the geological and mining con- ditions as gassiness increased with depth. The results of methane capture, both pre- drainage and post drainage were obtained by investigating several gassy mines.

Jan 1, 1982

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox's Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

Data collected from payload management systems at a number of surface mining operations show significant variance. Heavily loaded trucks travel slower up ramps than lightly loaded trucks. Faster trucks are slowed by the presence of slower trucks, resulting in 'bunching' and production losses. A stochastic model was constructed to simulate a truck haulage return cycle of 12.5 km at a large open pit gold mine in the USA. For a fleet of 35 trucks, the best estimate of the benefit achieved by a sustained reduction in payload variance of 25 per cent is a throughput increase of 1.6 per cent, within a possible error range of 0.6 to 3.2 per cent. This potential benefit is worthy of further investigation by Continuous Improvement teams at large open pit mines. The model also indicates that, under the right circumstances, provision of an overtaking lane can provide throughput benefits of up to ten per cent, The feasibility of providing unidirectional haulage circuits within large open pit mines should be examined.

May 1, 2010

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

The Curragh coal mining operation was designed and constructed to produce two coals initially at a rate of 4.3Mtpa. These are a high thermal energy steam coal primarily for domestic electricity generation and a low ash high quality coking product for the export market. Treatment of coals from four seams to achieve this requires a large and complex preparation plant and blending facilities incorporating state of the art technology. This facility was constructed during 1982/83. It has been designed for expansion to 6.8Mtpa capacity. The preparation and handling facilities were built at a cost of approximately A$80 million. Equipment includes 500 plus electric drives with a total capacity of 20 000kw. Commissioning was carried out in three phases : Staging - of the control system Coal Handling Facilities - conveyors, stackers and reclaimers for raw and product coals The Coal Preparation Plant - heavy media cyclones and froth flotation. A period of three months was devoted to the commissioning of the plant before requiring product coal to contract specification. This paper will describe the planning, implementation and results achieved.

Jan 1, 1986

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

From December 1994 to November 1997 Odin MiningÆs Estero Hondo alluvial gold mine in western Ecuador washed almost 3.2 million bank cubic metres of gravel to produce just over 2600 kilograms of pure gold at a recovered grade of about 0.8 grams per bank cubic metre. The operation was a simple open pit. Draglines stripped the overburden, backhoes mined the gravel, and trucks transported the ore to a stationary, gravity-based wash plant for processing. At start-up the planned throughput was 55 000 bank cubic metres/month, but a year later this had been increased to 100 000 bank cubic metres/month. From April 1993 to July 1997 a total of 440 churn drill holes and 15 pits were sunk to test the property. The methods used to prepare the resource and reserve estimates from the raw field data are described, and seven sets of completed estimates are used to track the evolution of the projectÆs resource/reserve base through the exploration, feasibility and production stages.

Jan 1, 2003

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By Kallioinen J

This paper discusses different possibilities to enhance coarse particle flotation using forth manipulation and improved flotation cell design. Experiments were carried out in laboratory, pilot and industrial scale ranging from 0.0015 to 100 m3/axle. During the work it could be shown that the conventional idea of one single flotation cell type for both fine, immediate and coarse flotation of coarse and fine particles need different impeller tip speeds and a different froth control objective for effective operation. For optimal operation for coarse feeds the tip speed must be reduced and the froth vertical velocity must be increased to compensate the respective drainage velocity and also the water film thickness must be taken care of. Turbulent eddies below the froth interface should be suppressed. The paper discusses the effects of different froth manipulation variables like froth vertical velocity and froth residence time to the recovery and selectivity. A function has been developed, between the residence time of the froth and the flotation cell's ability to produce an improved concentrate grade as a function of different operating and froth manipulation variables.

Jan 1, 1993

THE auriferous sulphide ores of the eastern end of Gippsland, and notably of the Cassilis and lVIitta districts, are amongst the most complex and refractory in Victoria-perhaps in Australia. The minerals occurring in these ores are pyrite, arseno-pyrite, zincblende, galena, and (in smaller amounts) some of the copper, sulphides, as chalcopyrite and covellite; and some of the antimonial minerals, notably stibnite and jamiesonite. In the oxidized portions of the lodes, the oxidized lead and iron minerals, and small amounts of the hydrated arseriiate of iron, are found.In the Cassilis mine, near Omeo, copper is present usually in quantities of under 1 %. The magnetic sulphide of iron is of fairly common occurrence. In, the upper levels of the Cassilis mine tin was usually present, the amount going up to 3% in some samples of concentrates. These minerals occur sometimes banded, but usually as an intimate mixture-pyrite and arseno-pyrite predominating. The gangue is usually quartz (blackened by enclosed particles of sulphides). Calcite, magnesium silicate and felspar are also present in varying amounts.

Jan 1, 1911

Violarite, (Ni,Fe) 3+x S4, is a ubiquitous secondary mineral in the supergene alteration zones of massive nickel sulphide deposits in Western Australia. It is formed by the pseudo- morphous replacement of pentlandite, pyrrhotite and/or millerite, and retains the textures typical of these precursors. Although the composition of the first-formed violarite is related to that of its precursor, supergene enrichment results in an increasing nickel:iron ratio toward the top of the supergene profile. In pentlandite-pyrrhotite ore, the replacement of pentlandite by violarite releases some nickel, which is consumed by the partial conversion of the pyrrhotite to iron-rich violarite. In pentlandite-millerite ore, on the other hand, the pentlandite, on conversion to violarite, appears to release excess iron that participates in the partial conversion of millerite to nickel- rich violarite. The characteristic textures exhibited by the secondary violarite and its replacement products in supergene and gossanitic deposits overlying massive nickel sulphide ores generally enable the original mineralogical compositions of the primary ores to be inferred.

Jan 1, 1973

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

By W J

Al ores arriving at the works which contain more than 3% sulphur, together with all sands and other fine residues, are delivered to the roasting department. Those that are in a coarse condition are first sent to the crushing plant, consisting of 15 in. x 9 in. jaw crushers and two No. 5 Krupp mills. The ore is here crushed through a quarter mesh screen. Any pyritic concentrates high in sulphur are given a preliminary roasting, to bring the sulphur contents down to about 12 % and the roasted material is delivered to the H. H. charge-making bins. Here the various ores, sands, residues, roasted pyrites, together with about 12 % of limestone, are made up into I-ton charges in hopper trucks with bottom discharge. The trucks are elevated by hydraulic lifts to a tramway running over the roasting furnaces, and the contents are dropped into hoppers over each furnace, from whence the mixture is fed into the centre of each furnace by means of a Challenge ore-feeder.

Jan 1, 1918

The Newmont Waihi Operations mill has undergone significant growth over its life. Initially designed as a single SAG mill operation, the circuit has been progressively upgraded since 1988 from a nameplate capacity of 600 000 tonnes per annum to the current rate of 1.3 million tonnes per annum. With future mining potential there is renewed interest to increase the processing rate even further. Over the next twelve months five sustaining capital projects will be undertaken and two major eco-efficiency projects will be completed. With the exception of the large grinding mills, most equipment on a gold treatment plant is replaced after 10-15 years. Waihi Gold mine has been operating for 14 years and has just recently received approval to replace equipment in five main areas; carbon elution, carbon regeneration, scats crushing, intertank screens and variable speed drives. Each project has been justified on improved process efficiencies and operating/maintenance cost savings. The two eco-efficiency projects involve a water balance model and a cyanide optimisation project, both of which are Corporate key performance indicators (KPI).

Jan 1, 2002

A continuing demand for exploration geologists, at a level well below that during the mineral "boom" of 1967-1971, will be highly selective. The exploration geologist must be more than the traditional geologist whose primary function has been detailed description of rocks and their recording on a geological map. He must be capable of 1. reconnaissance recognition of favour= able environments for ore mineral concentrations, 2. application and interpretation of techniques of search and evaluation, and 3. evaluation of economic, technological and political interactions that combine to make an ore deposit. Universities have an obligation to their students to provide them with a saleable skill, to educate them so that they can cope profess- ionally and socially, and to provide a mechan- ism by which education can be a continuing process. Humanistic and social studies, develop ment of communication skills, understanding of economic and management principles, ability to assess rock properties that influence extract- ion and beneficiation, and a knowledge of technological developments and limitations are necessary parts of the exploration geologist's

Jan 1, 1974

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By A S. Kurilko

For mines located in the cryolitic zone, thermal conditions are an important factor for all kinds of mining works, especially for ventilation of workings. In the present paper, some models of mine air heat transfer considering air distribution in a net of mine workings are developed. A combined solution is suggested for heat transfer and air distribution problems in mine workings and other underground structures located in the cryolitic zone. A software package is also presented for calculating temperature conditions in an underground refrigeration plant and for optimisation of ventilation conditions. This software uses a special 3D mathematical model to describe heat transfer in a freezing chamber between surrounding rock massif and stored product as well as between atmospheric air and the daylight surface of rock massif. A problem requiring strengthening of a backfill material and its thermal interaction with surrounding rocks during underground deposit mining by horizontal layers in conditions of the cryolitic zone is also discussed. The developed program takes into account cement consumption, geometrical dimensions of workings filled and a sequence of deposit mining.

Jan 1, 2005

The precious metallogenic belt and its geoloqical-tectonic location in eastern China.The precious metallogenic belt of eastern China is located in the western part of the Pacific gold metallogenic belt, and occurs in the upper levels of the continent cut by a deep fault structure tending NNE and NE, and active during the Mesozoic. The precious metallogenic period ranges mainly from Late Jurassic to Early Cretaceous (160 Ma-110 Ma); subordinate mineralisation occurred during the Hercynian period, and was rare in the proterozoic.Seven precious metallogenic belts are recognised from east to west, i.e. from continent to the margin active belts, as follows:1. Au-Ag-Te metallogenic belt of East Shandong Province2. Au-Ag-Pb-Zn metallogenic belt of west Liaoning-Miyun area3. Au-Os-Ir-Cr-Cu Mo metallogenic belt of Chengde Pingquan area4. Au-Ag-Pb-Zn metallogenic belt of Zhang Xuan area5. Au-Ag-Pb-Zn metallogenic belt of Zhejiang province6. Au-Ag-Se metallogenic belt of East Qinling area7. Au-Pd-Cu-Mo metallogenic belt of Wansu area

Jan 1, 1990