Search Documents

Water resources legislation in Brazil is evolving in a number ways. The nature of water resource ownership has changed in the last constitution (1988) so that now all water remains the property of the state and not the individual. There is also an increasing amount of legislation to control water access from the environment and regulation over water quality for water discharged. Finally, in some regions charging for water has been introduced and this is expected to become more wide-spread over the next few years. Increasing government attention to water legislation creates an increased need for mine sites to improve water management. As a fundamental basis for this, it is necessary to make robust estimates of mine site water balances, which also requires knowledge of the regional water balance to provide context for the mine water use. A conceptual model for mine site and environmental water balance is presented. Issues associated with conventional water monitoring are discussed. It is proposed that introduction of automated monitoring to provide comprehensive and consistent data is attractive. However, there remain a number of cultural and practical impediments to purchase, implementation and maintenance of effective monitoring, which are summarised.

Jan 1, 2009

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

By D S. Nicholson, T Marshall

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while opencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By Glaessner M. F

The island chains of the Western Pacific (Fig. 1), on account of their related origin, and the similarity of the rocks that compose them, constitute in the main a most homogeneous mineral province. They lie in a complex "mobile" zone of the earth's crust, that formed a geosynclinal area separating the continental margins of Australia and South-Eastern Asia (the so-called Sundaland) from each other, and from the margin of the Pacific Ocean proper (FIg. 2). The whole region was drowned at the close of the Ice Age, as a result of the rise of sea-level that accompanied the melting of the great ice caps in the polar regions, leaving only the higher portions as islands and peninsulas, many of them separated only by shallow seas or "shelves."The geosyncline was infilled with Mesozoic and Tertiary sediments that have undergone varying intensities of folding and metamorphism, and has been subject to intermittent periods of volcanic activity, continuing into the present. Midway between the two continental margins there is a narrow belt of pronounced negative gravity anomalies, with an extraordinary S-shaped convolution in the vicinity of the Banda Sea and Celebes, that marks the core of this unstable region. The folding within the "mobile" zonetrends parallel to it, so that the islands in its vicinity, which are regions elevated by folding, are all elongated in the strike direction of the folds. This explains not only the linear shape of Sumatra and Java, but the arc of islands enclosing the Banda Sea, and the peculiar shape of Celebes.Parallel to the belt of negative anomalies, at a close remove from it, is the line of Recent, or active volcanoes, that extends along the whole length of Sumatra and Java...

Jan 1, 1947

By J Col, D La Rosa, W Valery, A Jankovic

Metso Minerals Process Technology Asia-Pacific and South America (MMPT) has been working with operations around the world to increase their efficiency through æMine-to-MillÆ or Process Integration and Optimisation (PIO) projects. These projects have delivered significant improvements in mine efficiency, mill throughput and reduced operating costs at mines around the world. The MMPT methodology involves rock characterisation, site auditing, data collection, modelling/simulation and implementation of integrated operating and control strategies on site. This results in significant benefits to the operations û for example, 5 to 20 per cent increases in concentrator throughput have been measured. MMPTÆs rock characterisation utilises simple and inexpensive measurements that can be performed by trained site personnel. The advantage of these measurements is that a large amount of data can be collected in a very short timeframe, as the samples do not require shipping to an outside laboratory. Typically, a PIO project starts with a site visit to perform blasting and process audits, collect high quality data including measurements of run-of-mine fragmentation and survey data around all crushing and grinding circuits. These measurements are combined with rock characterisation and the definition of strength and structure domains to model the complete production chain. Site-specific models of the blast fragmentation, crushing, grinding and flotation processes can then be developed. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG or conventional grinding circuits. Process improvements can be higher mining productivity, higher mill throughput, decreased overall operating costs and higher flotation or leach recovery. This paper discusses a recent application of PIO conducted at a large open pit operation in South America and emphasises the potential that every operation has to ædo more with what they haveÆ.

Jan 1, 2007

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Craw

Otago Schist and Klondike Schist are two Paleozoic-Mesozoic metamorphic belts on the circum-Pacific margin in which there has been a long history of abundant alluvial gold mining, but only minor hard-rock gold mining.   Modern exploration for hard-rock gold is ongoing in both belts, and the active Macraes mine in Otago (>2 Moz production) highlights the hard-rock potential of the geological setting of these belts. Hard-rock gold mineralisation in both belts formed in the latter stages of schist exhumation, after rocks were subjected to major regional ductile folding and then uplifted through the brittle-ductile transition. The majority of known hard-rock gold-bearing systems in both belts consist of well-defined, but generally discontinuous, vein swarms. Most Otago veins are hosted in steeply dipping post-metamorphic normal faults and fractures. However, the Macraes mine is hosted by a late-metamorphic shear zone, and much ore is sulphide-impregnated auriferous schist. Goldbearing veins in the Klondike schist are hosted primarily in extensional sites associated with post-metamorphic compressional structures. Some disseminated sulphide mineralisation is associated with Klondike veins and this is important as it extends the exploration target for these veins. No foliation-parallel late metamorphic mineralisation has been identified in the Klondike but exposure is relatively poor compared with Otago and both schist belts are highly prospective for deposits of this type.

Jan 1, 2007

The .subject of this paper is to briefly outline various methods of stockpiling and reclaiming, and the use of different types of bucketwheel re- claimers and stackers in these operations. The paper examines briefly the different types of bucketwheel equipment, their operations and relates them to different stockpile layouts, giving examples of their application in Australia.

Jan 1, 1973

By D Chalmers

Drill and blast mining techniques are used to mine coal outburst prone and high gas content coals in Australia. As the risk of an outburst is increased in high gas content coal, it is considered that drill and blast is the safest way to mine coals that refuse to yield gas even after considerable gas drainage efforts. The availability of suitable explosives for drill and blast in Australia is dependent on the æBuxtonÆ tests. With the diminished coal operations in England, the type and supply of such explosives is tenuous, causing significant disruption to the production of coal in some mines. In an attempt to free up the availability of explosives a review of the methods used for the testing of coal mine explosives was undertaken to ascertain the scientific basis for these tests. It was hoped that this comparison would allow regulators to have the confidence in explosives that had been tested elsewhere. Although this was not achieved, it has spawned a major research project that aims to better understand the mechanisms involved so that either confirmation of the current testing regime can be achieved or more suitable and scientifically based tests can be adopted. This paper looks at the ongoing research program investigating the parameters that are involved with methane ignitions from explosives. By utilising high-speed data capture and processing the research project is trying to view an ignition as it happens to identify the mechanisms involved so that better explosives can be designed for the coal mining industry.

Jan 1, 2007

By N DavT

Pyritic tailings from the Quirke mine waste management area in Elliot Lake, Ontario were subjected to long-term column leaching experiments in two PVC columns measuring 122 cm in height and 15.2 cm in diameter. At the end of the leaching experiments, the columns were taken apart and sampled at 5 cm intervals for quantitative mineralogical and geochemical characterisation. Each column is represented by a total of ten samples. Polished sections, prepared from the samples, were studied by optical microscopy, scanning electron microscopy, electron microprobe and X-ray diffraction techniques. Mineral quantities were determined based on linear mixing models of whole rock and mineral compositions. Pyrite particle sizes were measured by image analysis interfaced to an electron microprobe. The tailings are coarse-grained (ie 96 per cent passing 75 ¦m) and composed of quartz, K-feldspar, muscovite and pyrite. Pyrite is homogenous and occurs as liberated particles displaying angular to subangular boundaries with strong dissolution features at the end of the leaching experiments. Based on up to 3518 particles measured in a sample, pyrite particle sizes range from 1.7 to 78.6 ¦m. Pyrite concentrations vary from 0.1 to 7.8 wt per cent, depending upon their location from the top of the columns. These correspond to pyrite losses of up to 99 per cent from their original level of 7.2 wt per cent in the upper half of the columns. Pyrite oxidation rates in terms of moles of pyrite oxidised per mole of pyrite per square metre per second were calculated from the effluent data and the measured pyrite particle sizes. The rates vary from 1.71+10-12 to 5.78+10-10 mole+m-2+s-1 within the 1.5 to 3.5 pH range for 10 ¦m particles. These results are comparable with the published oxidation rates at pH 2 where the dissolved oxygen is the only oxidant.

Jan 1, 2003

In a previous study, various pyrite depressants were examined to improve the flotation performance of a copper-sulfide ore. Optimal results from this study were used to examine the effect of elevation on recovery and grade. Tests were conducted at elevations of 3350, 1735, 610 and -760 metres, consisted of five repetitive experiments for statistical analysis, and were performed both with and without airflow control. Tests were also performed in a glove box at Montana Tech to mimic the pressure conditions. Results indicate that both recovery and grade are dependent on pressure via bubble size and airflow suggesting that pressurised flotation cells should be considered for operations, particularly those at high elevation. Economics are extremely favourable for implementation because ensuing capital expenses are inconsequential with minimal time for return-on-investment.

Jan 1, 2005

The subject of steel wire ropes covers such a wide range of points that it would be impossible to deal with it fully in one paper, and in view of the apparent scarcity of published information on the subject it is proposed in this paper to deal with those items which should give the mining engineer a better understanding of the basic factors which affect the design.selection, and use of ropes. The matter will be considered under the following headings:-1. Brief history of steel wire rope-making.2. Rope-making terms.3. Wire rope materials.4. Characteristics affecting economy, operating life, and serviceability of a rope.5. Properties of construction of rope, and stresses met with in wire ropes.6. Drum and sheave sizes and sheave bearing pressures.7. Storage, handling, and maintenance of ropes in service.8. Common factors affecting rope life, particularly winding and haulage ropes.9. Inspection of ropes.GENERALWire rope, which was invented for, and first applied to mine winding, has become an indispensable aUXiliary throughout the whole field of mining, be it for underground, open cut, or dredge work, as well as the requirements of transport and treatment of ores.Though wire ropes appear simple collections of wire and fibre, the demands made upon them are many, and the stresses and abuses to which they are exposed in service are varying, and often of serious dimensions.The exposition of these stresses and abuses, particularly dynamic stressing, corrosion, etc., all of which seriously affect the safety and economical life of the ropes, is often enough to frighten most practising mine staffs, who are aware that before the requirements of economic operation stands the still more important question of safety in mining.

Jan 1, 1947

Underground measurements, observations and computed simulations, started a long time ago were concerning the study of : - occurence of typical rockburst, - inducing, stretching of main fractures in the roof of caved longwalls. They made obvious a foundamental phenomenon of inducing of strata fractures involving contact be- tween two layers quite different in their elastic characteristics : coalseam and rocklayer.. The start of primary cracks in maximum abutment zone takes place in the rock near the contact surface. It is opening of crevasses induced by traction stress component resulting of difference of rigidity of both materials and no sliding on in- terface. Occurence and stretching of these crevas- ses are a rheological phenomenon so that the rate of advance and stops of the face influence the distance between the crevasses and the stretching of these ones. The characteristics of these cracks in space and time affect mining conditions. So it is for fractures proximity and expan- sion inducing eventual blocks formation in longwall roofs in front of faces, for depth and delay of road- ways ribsides fracturing, inducing some rockbursts. In longwalls roofs, cracks initiated in front of a face can be either quite close or quite distant each from the other one, according to the depth of crushed coal in front of the face, which af- fects also extension of the cracks.

Jan 1, 1988

By Orr T. O H, Hodkinson I. P

The Mount Leyshon breccia complex is located on an east-west trending contact between Cambrian metasediments (Puddler Creek Formation) and the Ordovician Mt. Leyshon granite, within the Lolworth-Ravenswood block. Detailed mapping of basement, breccia and igneous unit geometries, crosscutting relationships and resolution of complex chronological relation- ships indicates that the Mt. Leyshon breccia complex should be reinterpreted as a number of intrusive igneous and breccia phases. This is in contrast to a previously published account of a largely extrusive geological setting. A complex structural history dominated by strike-slip faulting is preserved within the basement units and is responsible for controlling the location and geometry of the breccia complex. The breccia complex has been divided into brecciated "basement", "main pipe breccia" and an "interactive magma/breccia sequence". Main pipe breccia (the most voluminous unit within the complex) has been re-interpreted as an intrusive breccia, rather than an extrusive or vent fill as previously proposed. This is based on the following evidence: 1. the facies characteristics of the main pipe breccia, 2. the presence of a progression from cohesive basement through to mixed breccia, 3. minor basement block rotation during breccia complex formation, and 4. the partial structural control on the main pipe breccia. No unambiguous evidence exists for pyroclastic facies, although the fine breccia variant commonly contains "accretionary structures", very similar in appearance to those formed during pyroclastic processes. In view of 1. above, they are interpreted to be the product of particle accretion during upward movement of fragmental material, although an origin due to altera- tion cannot be completely discounted. heir occurrence in the main pipe breccia indicates that their presence within a rock unit is not necessarily diagnostic of nvroclastic nroeesses.

Jan 1, 1991

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

The mobility of radionuclides released into aquatic, terrestrial and subsurface environments by mining, industrial processes is an area that deserves significant scientific attention. The presence of microorganisms in these environments can influence the transport of radionuclides. Free-living microorganisms constitute mobile suspended particles that may have a radionuclide sorbing capacity higher than that of the environment. Radionuclide transport will then proceed faster with than without microorganisms. In contrast, if the majority of the microorganisms are growing in biofilms on surfaces, transport of radionuclides may be reduced. Microorganisms can directly sorb radionuclides either within the cell structure or on the cell wall. Radionuclides could also be sorbed by minerals precipitated by microorganisms. Microorganisms produce complexing agents that can influence radionuclide mobility. The involvement of microorganisms in biogeochemical processes is related to their ability to include various chemical elements and their combinations into biochemical redox reactions. Microorganisms can alter the extent of radionuclide oxidation that results in their deposition as a result of the formation of insoluble forms. Some studies have shown the bioremediative potential of stimulating reducing bacteria to use some of the soluble radionuclides as electron acceptors and thus precipitate them out of solution. The microbial involvement in providing a barrier for radioactive element migration (uranium, technetium) and the formation of ores (eg uranium) has been justified. The mediated impact of microbial activity on radionuclide migration occurs through its effect on the ambient geochemistry by geochemical speciation changes, pH changes and changes to the ambient redox potential. As the mobility of many radionuclides depends on the pH and redox potential of the environment, these microbially mediated geochemical changes can influence radionuclide migration through changes to both the dominant radionuclide species and mineral phases.

Jan 1, 2004

The New Zealand Mines Rescue Brigade was established as a result of the Dobson mine disaster on 3rd December 1926, when 9 men lost their lives. Prior to this, there had been four major disasters in New Zealand coalmines, with a total of 145 fatalities. Only large-scale events such as explosions or major fires were considered reportable. Until and including the Dobson disaster, no mine emergency response facilities or organisation was in place.   Unfortunately, over the next five decades the establishment of a Mines Rescue Service did not mean that disasters involving multiple fatalities ceased. The coal mining industry continued to suffer the consequences of poor mining practice, inadequate or inappropriate monitoring and management, and sometimes complete disregard for the regulatory requirements current at the time.   The role of Mines Rescue has been defined in statute, and regulated by Coal Mines (Mine Management and Safety) Regulations. Currently, the statutory obligations have been under the Mines Rescue Trust Act 1992.   The Mines Rescue Brigade historically, has primarily been a reactive service, with stations and facilities established to train brigadesmen in emergency response procedures, specifically to mobilise in the event of a call-out at any one of the many coalmines operating within each stationÆs area of jurisdiction.   Over the last ten years, this role has changed. The service has adopted a proactive approach to emergency response, and has established a close liaison with all mining and tunnelling operations throughout industry, both underground and surface. The objectives have become emergency prevention focussed, and the service has incorporated a range of theoretical and practical training, simulated exercises, more sophisticated equipment and techniques, and a desire to ensure that emergency response capabilities are not needed, whilst maintaining the traditional and statutory obligation to respond if they are needed.

Jan 1, 2004

The Mammoth Copper Deposit consists of three distinct orebodies adjacent to the Mammoth Fault. This fault is arcuate, changing from a normal tension fault to a shear strike fault just to the north of the mine. Movement on the fault was probably contemporaneous with deposit- ion of the adjacent sediments. In the upper levels the No. 1 orebody occurs within a brecciated zone in the footwall of the fault, but at depth the No. 2 and 3 orebodies are stratabound by two brecciated lithologic horiz- ons. The host rocks are impure sandstones, arkoces and quartzites, which in the mine area are near the top of the Lower Proterozoic Myally Beds. Overlying these beds is a conglom- erate siltstone sequence which has been assumed to be the base of the Gunpowder Creek Formation. North and south of the mine the conglomerate rests on an erosional unconformity representing a major time break, but in the mine the uncon- formity and conditions of deposition of the conglomerate are obscure. Some mineralization is contained within the conglomerates. The sulphides present are chalcocite, bornite, chalcopyrite and pyrite. Chalcocite is dominant in the upper levels but could be en- riched by supergene processes. At depth, bornite becomes the dominant copper sulphide with lesser amounts of chalcopyrite, pyrite and primary chalcocite. Throughout the orebody minor digenite and covellite occur and arsenic is a minor constituent bound up with the pyrite. The bulk of the sulphides occur in stringers, fractures and breccia interstices but finer grained primary bedded sulphides can be observed. The genesis is probably a complex process in- volving active tectonic movements extending from deposition to post lithification giving numerous phases of brecciation and redistribut- Ion.

Jan 1, 1974