Search Documents

By Vogwill R. I J

The Boddington Gold Mine, operated by Worsley Alumina Pty Ltd, is located about 100 km south of Perth and is one of the largest-producing gold mines in Australia.Multiple open pits are planned and several extend below the water table, through the deeply weathered lateritic profile and into the underlying Archean bedrock. Groundwater related mining problems, such as poor trafficability, wet floor conditions and slope instability began to occur early in 1990.The mine is located within Archean greenstones which are steeply dipping and faulted. Rock types include mafic to felsic volcanics, pyroclastics and sediments. These rocks have been regionally deformed and metamorphosed and are intruded by quartz micro-diorites and post-mineralisation dolerite dykes. Deep weathering has produced a typical oxide profile consisting of laterite, clay and saprolite zones underlain by weathered to fresh bedrock.

Jan 1, 1993

The Snap Lake Phase I project initiated a subsampling campaign on the material (kimberlite/metavolcanic/granite) mined and treated for diamonds. The campaign was aimed at determining the optimum subsampling program to subsample the feed to the bulk sample plant (BSP) for the duration of a sampling campaign. This paper describes the application of GyÆs formula for determining the subsample size and other good sampling practices to determine this subsampling campaign. Three main issues are discussed: the use of a hammer sampler to sample off a moving conveyor and the practical experiment to determine the optimum subsampling program; bias introduced by laboratory equipment including two sizes rotary splitters; and variability of the feed material to the BSP over time.

Jan 1, 2005

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

By Tronson K

Improvements in technology do not necessarily lead to higher profits: the benefit of lower costs can be captured by coal buyers, governments and workforce rather than by the colliery operators. The economic impact of longwall mining in Australia has been critically assessed to provide lessons for the future. For a variety of reasons, companies investing in longwall equipment in the past five years have generally not achieved an adequate return on the funds invested. The effect of technological innovation must be examined in the light of competitive forces operating in the market. Projections of cost reduction trends in the coal industry have been applied to a world cost model to provide a picture of the coal industry in the year 2000.

Jan 1, 1988

By Watsford R. M S, Hutton R

Following the delineation of significant extra ore reserves during 1990, the decision was made to expand production from 350,000 tonnes of run of mine ore per year to initially 600,000 tonnes increasing to 750,000 tonnes per year. The existing plant consists of a conventional three stage crushing plant followed by a heavy medium separation plant that produces a product prior to grinding. Grinding is conducted in three stages of ball mill in series. Alternatives examined for expanding production included: aò SAG mill - ball mill circuit replacing the secondary and tertiary stages of crushing, the heavy medium plant and the existing ball mills; and, upgrading of the existing circuit configuration.

Jan 1, 1991

Norway, a country large in area but small in population, has put large effort in protect- ion of its inhabitants in case of war. The Civil Defence has provided shelters for more than 50% of the population. Some of these shelters are put into rock. Since rock installations give large resis- tance against weapon effects and also by advan- tage can be used for several purposes in peace- time, an interesting development has taken place the last decades. In towns and cities you will find sport halls, swimming pools, bowling and shooting ranges etc in rock, which easely can be conver- ted to civil defence shelters. Some typical installations are highlighted in the following.

Jan 1, 1987

By R O. James

The usual focus of papers on fatty acid collector action in non-sulfide flotation is on the adsorption of the carboxylate and/or neutral molecule species at the mineral-solution interface. Little attention is paid as to whether or not the solution conditions correspond to true solutions, micellar and other self-assembly objects or precipitates. Our examination of the solution chemistry of the important fatty acid collector, oleic acid, has revealed that many, if not most investigators set their experimental conditions to be in micellar or precipitate domains while arguing, often by implication, that they have only solute species present. We have investigated the equilibrium solution domains usually encountered in studies of oleic acid flotation of such minerals as barite, calcite and fluorite. The alkaline earth-fatty acid and liquid oleic acid precipitate phases exert a strong influence on the solution chemistry, a fact not often appreciated in many studies.

Jan 1, 2005

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By D Ray, D Brett

A clay-capping trial was established in 1996 on Magazine Dump at the Mt Lyell Copper Mine. The trial was initially constructed under the Mount Lyell Remediation Research and Demonstration Program, a co-operative venture between the State and Federal governments. The detailed engineering design for the clay cover included the following features; reshaping and compaction of dump batters, 5 m vertical bench interval, overall side-slopes of 2.5:1, emplacement of clay in four 150 mm lifts, compaction by a 10 t vibrating roller or ætrack rollingÆ on batters with density testing for quality control. A small section at the base of the dump ( The trial also generated certain unexpected findings. Field permeability tests on the cover yielded uncertain results and oxygen remains available throughout the dump. The flow data indicate that, while total outflow has decreased as a result of storm shedding, inputs from groundwater and batter infiltration are still significant. Outflow during the driest weeks of the year may have risen following capping. Detailed assessment of the data is hampered by insufficient pre-capping information; however, there is a possibility that conductivity flux emitted when flows in the receiving environment are at their annual minimum is unchanged or worse post-capping.

Jan 1, 2003

Not so many years ago the reason for an inadequate result from a geophysical survey was insufficient data or poor quality data. In many instances such as gravity, magnetic and radiometric surveys, both these constraints are vanishing or have vanished. High quality sensors, improved data storage, accurate differential GPS and top quality interpretive software now enable the interpreter to understand not just the cause of the anomaly but the host environment in which it resides. Examples of potential field data and also data provided by the more complex electromagnetic systems, from Australia Ghana, West Africa, are used as illustrations.

Jan 1, 1997

By Elliot B. J

Cobalt is principally produced by hydrometallurgical means from the copper-cobalt ores of Zambia and Zaire. In addition cobalt is commonly found in minor quantities in association with nickel and copper-nickel orebodies. Generally the level of cobalt common to these latter orebodies does not warrant separate processing unless the metal price reaches levels last achieved in 1979 and 1980. For pyrometallurgical processing the distribution of cobalt and the factors which affect the distribution of cobalt between matte and slag are not well understood. A limited amount of fundamental research has been completed on cobalt distribution both for simple oxide and matte systems. The paper briefly reviews the relevant literature on theoretical aspects of cobalt distribution between metal and slag and the deportment of cobalt in sulphide smelting circuits. The deportment of cobalt in the Kalgoorlie Nickel Smelter circuit is critically analysed and areas where recovery improvements may be achieved are highlighted.

Jan 1, 1989

In the geologically prospective nations which rim the Pacific Ocean, mineral deposits offer great potential to create wealth for social and economic development. The paper first examines the geological and economic attributes of potential mineral wealth based on current outlook assessment of all significant base metal deposits discovered to 1988 in two Pacific Rim nations - Australia and Canada. The variability of mineral wealth among the economic deposits evaluated and the major contribution of the few world-class discoveries to total mineral wealth are highlighted. Then, the essential but too often neglected linkage between the makeup of potential wealth and its actual realization is analyzed. The impact of taxation and the role of exploration are crucial in this regard. Finally, the ingredients of exploration success, prerequisites for realizing the mineral wealth of nations, are examined.

Jan 1, 1995

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

By Buizen M

The results of calibration trials conducted on parachute stoppings under a recently completed NERD&DC grant are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in mine recoveries, sealing sections and rescue work. Parachute stoppings are one of a series of non-rigid ventilation control structures specifically designed for quick installation in emergency situations, for use in high production/rapid advance areas and areas suffering roof-floor convergence.

Jan 1, 1988

By Marwick PL

As part of its operations Hamersley Iron operates a heavy medium Concentrator to upgrade low grade, unsaleable iron ore to produce saleable lump and fines products. Firstly, the attempts at delivering a blended feed in both chemical and physical characteristics are presented. Improvements in blending controls are shown to have given process performance improvements. Secondly, improvements to the feed preparation section are detailed. These alterations are providing a much cleaner feed to the subsequent processing stages.

Jan 1, 1987

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003