Search Documents

By Hematian J

A high horizontal stress field has significant effect on the stability of underground roadways and influences the design of a support system in this environment. The high horizontal stresses at E1lalong Colliery, NSW, Australia provided the environment for this study. Samples of coal measures 'rock were collected and tested to determine their mechanical properties. The lithology, stress state, geometry and conditions prevailing in particular areas of the mine were obtained from geotechnical reports available at the mine and by field observation. The results of a series of finite element models constructed and tested under various conditions provided a basis for comparison with field observations. Analysis of the results indicated sufficient correspondence to provide a basis for the proposed design of an optimum support system. It is not suggested that finite analysis provides 'exact answers', but it does show the relative importance and interaction of various parameters.

Jan 1, 1995

By R Berry, A Escolme

"Predictive geometallurgical models are being developed for the Productora Cu-Au-Mo deposit based on geochemistry to reflect variability in Cu species based on Cu sequential leach data (ie oxide, transitional-oxide, transitional-sulfide, sulfide and non-recoverable Cu).Productora, located in the coastal range of northern Chile, is a magmatic-hydrothermal tourmaline breccia-hosted, structurally controlled Cu-Au-Mo deposit hosted by a thick sequence of Jurassic rhyodacitic volcanic rocks. North and north-west striking fault sets control the distribution of mineralised breccias. Alteration is widespread, complex and pervasive. Hypogene alteration assemblages range in composition from distal magnetite-amphibole, to sodic-calcic, to sodic, to phyllic, to proximal potassic. Low-temperature advanced argillic assemblages are locally juxtaposed next to proximal high-temperature K-feldspar-tourmaline assemblages. The dominant hypogene Cu phase is chalcopyrite.A simple Cu species classification scheme based on sequential leach data and S per cent was devised to account for non-recoverable Cu (ie non-sulfide Cu), which is insoluble in weak acids. Through machine learning, a proxy for this Cu species classification scheme was developed based on: depth, Ca per cent, Cu per cent, Fe per cent, K per cent, Mn ppm, S per cent and Ln(Cu/S) plus logged regolith class, thus allowing classification to be extended to areas of the deposit where no sequential leach data are available. The modelled data has been used to generate deposit-wide 3D models for Cu species classification.The validity of the proxy Cu species classification model is being tested against the results of flotation analysis. Initial results indicate that geochemical proxies can be used to successfully predict Cu species class and provide a high density of classification data.CITATION:Escolme, A, Berry, R and Hunt, J, 2016. Predicting Cu Species Classification Using Geochemistry at the Productora Cu-Au-Mo Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 113–118 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

The goal of the Bureau of Mines, U. S. De- partment of the Interior, diesel engine research program is to reduce exhaust emissions and mini- mize the risk of fires and explosions caused by the use of diesel-powered equipment in under- ground mines. Significant results of research conducted during the last 5 years are briefly described, with references to published reports on specific topics. Topics covered here include brief discussions of a newly completed diesel research laboratory, the effects of a fuel addi- tive on diesel exhaust particulate matter, the effect of diesel engine maintenance on emis- sions, a diesel particulate filter for equipment used in underground metal and nonmetal, and coal mines, and lastly, the prototype hydrogen- powered mine vehicle. These research accomplishments could favor- ably affect the mining industry by reducing the health and safety hazards associated with the use of diesel-powered equipment in underground Mines.

Jan 1, 1988

By Guvenir HA

This paper summarises a cost optimisation procedure by minimising the total drill metres and the overbreak that occurs in tunnel excavation in medium strength rock (uniaxial compressive strength

Jan 1, 1995

By Teague JWS, Jung RF, Kadletz O, Jones DR, Jones CJ

A study of the passive treatment system for Hilton minewater revealed that it consists of four main process steps. The water, which contains soluble and particulate iron and zinc and is supersaturated with CO , is pumped to the surface and then passes throuqh a degassinq unit into settling ponds where larger particles of iron hydroxide, containing some adsorbed zinc, can settle out. The still turbid supernatant is pumped to the top of a hill, from where it is allowed to trickle in a broad sheet, releasing CO , towards an earthen channel in the valley below. Consequently the pArises from around 6 to 7.5. This in turn promotes further decrease in the concentration of soluble zinc by increased adsorption of zinc on to iron hydroxide particles. The channel then transports the water to the third process in the system - a 53 ML pond acting primarily as a flocculation-sedimentation basin. The clarified water overflows into a second channel, downstream of the pond, which constitutes the fourth process in the system. Here, copious quantities of filamentous algae further reduce zinc concentrations to acceptable levels before the water is collected for recycle into mine operations. The work reported here represents a detailed study of this system and describes the optimisation of the operation of each of the individual steps involved.

Jan 1, 1988

The Permian rocks at Gympie were first studied as far back as 1868 in conjunction with the discovery of gold. The relationship of the Gympie Group to other sequences in the Gympie Composite Terrane is an important subject of investigations in a new mapping project of the Geological Survey Program of the Department of Resource Industries.In two areas the Gympie Group has been divided into four defined formations. They are the Highbury Volcanics (base), Ram mutt Formation, South Curra Limestone and Tamaree Formation (top) in the Gympie area, and the Mant basalt (base), Kolbar Formation, Gigoomgan Limestone and Teebar Formation (top) in the Gigoomgan area. Geochemical and lithological evidence from the basal volcanics of the Gympie Group (Highbury Volcanics, Mant basalt) indicate that they developed in an intraoceanic island arc setting. The overlying volcaniclastic sediments (Rammutt Formation, Kolbar Formation), which contain some continentally-derived material, are mainly of local derivation and shallow-water marine. A hiatus is present at the top of the Early Permian Rammutt Formation and Kolbar Formation. Following the hiatus, limestone sedimentation characteristic of a basin of restricted circulation developed in the Late Permian. There is some evidence of a hiatus between the limestone deposition of the Gigoomgan and South Curra Limestones and the overlying probable turbidite deposits of the Teebar and Tamaree Pnrmatinnc

Jan 1, 1990

By Billington WG

A structural study of northwest Fergusson Island, part of the D'Entrecasteaux Group, was undertaken using colour and monochrome aerial photography and Landsat imagery. The resulting interpretation shows an upstanding, in part, dome-like metamorphic core complex, which is bound on three sides by an en echelon series of low-angle, thrust faults. Faceted gneissic layers occur throughout the complex. These facets are triangular in plan view and range in size from a few tens of metres, to massive composite zones which traverse the entire uplifted zone, The lower surface of each of the facets are, in fact, low-angle decollements which, during uplift, slid one upon the other to accommodate the vertical and extensional movements. As a consequence, deep structural valleys developed which widen towards the zone of maximum uplift. In many places, recognisable topographic features are replicated on both sides of these valleys, and under the stereoscope can be visually reconstructed to their original pre break-up positions. The southern margin of the core complex is less dome-like and falls away, via a series of deeply-entrenched structural valleys, towards a volcano-studded lowland. The lowland appears to belong to a rift or arm, stemming from the more southerly located Goodenough Bay Infrabasin.

Jan 1, 1987

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

The following is a brief summary of the Bulli Colliery and its method of operation when Australian Iron and Steel Ltd. took control.Bulli Colliery is situated about a mile west of the village of Bulli and is some 10 mUes north of the Australian Iron and Steel Company's Steelworks at Port Kembla.The mine is owned by Australian Iron and Steel Limited, who purchased it in 1936 from the liquidators of Bulli Colliery and Coke Works.It is one of the oldest working coal mines in Australia, having been opened about 1858 and has worked more or less continuously since that date.The seam worked is the No. 1, or Bulli, Seam, which outcrops along the escarpment of the Illawarra Range and is generally operated by tunnels, the portal at Bulli being some 440ft. above sea level.The colliery holding is fairly extensive, but the coal seam over a large portion of the area within two miles of the outcrop has been more or less destroyed by an intrusion of basalt.At present there is no coal being worked within a distance of about 21 miles from the surface, the farthest workings being about four miles from the tunnel mouth.The existing main haulage road, for the first two miles from the portal, is not straight; it is very narrow over fairly long stretches and has many changes of grade varying from 3% in favour of the load to 13% against the load.The dumping station and screens are situated close to the portal of the haulage tunnel, and at this point the coal is loaded into railway hopper waggons, which are then hauled by rope to the top of a self-acting incline. The waggons are lowered down the incline, a distance of approximately! mile, the ruling grade being about 18 %.From the bottom of the incline, waggons are hauled by Company's steam locomotive to exchange sidings from whence they are taken by New South Wales Government Railway engine to the Company's Steelworks at Port Kembla.

Jan 1, 1947

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

By P Crorkan

Within the framework in which future exploitations for Codelco-Chile Divisi=n El Teniente are situated, regarding the deepening of its reserves and the geotechnical problems that affect their recovery, it becomes strategic to evolve with new variants, which make deep mining possible. Codelco ChileÆs Divisi=n El Teniente is progressing within its long-term planning the exploitation of a sector called Esmeralda, which includes its removal through the gravitational caving method (panel caving). It is planned to use pre-caving, which basically consists of developing and undermining the undercut level, without having developed the infrastructure of the production and transport levels. This is carried out in order to achieve a better redistribution of the stresses, thus obtaining higher quality in the infrastructure development of these levels as well as less risk. The extraction reserves for this area, estimated through the opportunity cost selection criteria, were determined at 348 million tons with an average grade of 1.014 per cent Cu. The project carried out geological and geotechnical studies in order to prevent the geomechanical risks of the sector to be exploited, which is a site conformed totally by primary ore. Lithologically, it occurs mainly in Andesite, located at the western limit by Brecha Braden Pipe. There are also varieties of porphyries and hydrothermal breaches of anhydrite. The Esmeralda Mine production program will increase from 4000 tpd (average) in 1998 to its 45 000 tpd rate of production estimated for the year 2005. The approved investment for the period 1995 to 1999 is $US 150 million, out of a total $US 213 million for the project. At feasibility study level and before the project, it showed a Net Present Value of $US 342 million, an Internal Rate of Return of 37 per cent and an IVAN indicator of 2.3 for a ten per cent discount rate and a copper price of 100 US cents/lb.

Jan 1, 2000

The Junction Reefs gold bearing deposit is situated on the Lyndhurst Mining Field in mid-west New South Wales. It is located within a triangle of three country towns namely, Blayney, Cowra and Canowindra, all three townships are approximately 25 km from the current operational mining leases. The district is well developed, having been settled for more than a cen- tury. However, being close to the Cities of Orange and Bathurst it is real- lised, instantly, that mining leases have been pegged, in this area, almost boundary to boundary. The lease patterns are, with few exceptions, those which had been estab- lished more than seventy-five years ago. These types of lease patterns may not assist the proper exploitation of a large district where there have been many discoveries of gold, copper and other metals.

Jan 1, 1988

The Southern Mines Rescue Station (S.M.R.S.) has been established for 55 years and in the past 15 years has had only 4 major call-outs. Whilst the mines rescue training program has continued to expand, the Station has become involved in other work which includes mine worker training and limited research. Notwithstanding, the prime role of the Mines Rescue Station has not been overlooked and the Station has only advanced with the many changes that have occurred in the coal industry. The Rescue Station activities are financed by contributions from Colliery proprietors and the aim of the S.M.R.S. Committee is to provide a service in which colliery management and mine workers will have a high degree of confidence.

Jan 1, 1981

Mill liners provide the wear-resistant surface within grinding mills, they also impart motion to the mill charge, ie the grinding process, by providing the key between the charge and mill shell, and, at the discharge end, they remove the ground contents of the mill. As semi-autogenous grinding (SAG) mills have grown in size the process aspects of liner design and their impact on mill performance have become particularly important. While feedback from practical experience is critical to good mill liner design, increasingly sophisticated computer-based tools are being developed to assist in mill liner design.

Jan 1, 2007

By R Castroviejo, F Segundo, C Brea, J-C Catalina, H-J Bernhardt

Optical microscopy is a basic but still indispensable tool for examining mineral parageneses in ores. The design and concepts behind the reflected light ore microscope have obviously not been subject to spectacular technical evolutions in the last decades. However, digital imaging capabilities have opened new and stimulating perspectives for automated mineral identification. Recent works in developing multispectral image analysis (Pirard, 2004) have demonstrated its superior potential with respect to conventional colour imaging, but at the same time reconciliation with spectroscopic databases such as the Quantitative Data File III (Criddle and Stanley, 1993) still needs a more in-depth investigation as well as the possibility to extend both imaging and spectroscopy into the near infrared domain. In this paper, the authors present results gained from multispectral imaging in the range between 400 and 1000 nm together with spectrophotometric data from the QDFIII database, with an emphasis on minerals that cannot be easily distinguished in the visible spectrum.

Jan 1, 2008

The title of my address today 'An Environment for Mineral Development' is a play on words, but I wish to use the meaning of the word environment in the broadest possible context to comment on those factors that control mineral development in New Zealand today. Of prime importance, let us consider the current economic environment in which New Zealanders live and work, as individuals and communities, and as a trading nation. It is the expanding growth requirements of the emerging nations and the interactive economic forces of our international trading partners and competitors, that dictates New Zealand's economic environment and thus the priority to develop its natural resources. As an itinerant New Zealander who has kept a watching brief over the economic environment in New Zealand over the last 30 years, I say, without prejudice, that I am concerned to have seen New Zealand's external and internal trading position deteriorate so rapidly in the last decade. I am concerned that a significant proportion of the population has been extremely slow to realize that with the creation of the European Economic Community, in the late 1950s, and following the first OPEC oil crisis in 1973, New Zealand in a corporate sense came close to technical bankruptcy.

Jan 1, 1985

Outsourcing of mining operations and services is done for various reasons and there is no single model which fits all situations. Experienced contractors and mine owners have also developed, more often than not, jointly, numerous commercial arrangements and project delivery methods to suit their particular project. It is often the case that some mine owners who have not considered outsourcing to contractors do so because of a simple lack of understanding of the potential benefits. This paper will highlight the potential benefits and perceived disadvantages of outsourcing for mine owners and demonstrate how these issues have been addressed by the mining contracting community over recent times as well as demonstrate the evolution of current commercial arrangements in engaging mining contractors.

Jan 1, 2006

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

By Grouhel P

Blasting performance is directly related to the characteristics and efficiency of the explosives used. The selection of the correct explosive for particular blast conditions and objectives depends on the ability to characterise the performance of individual explosive products. Techniques have been developed by the JKMRC to measure explosive performance and assess the impact of explosive performance on blast results. Studies conducted at a number of mine sites have shown that different types of explosives perform quite differently and that the performance of any particular explosive can vary significantly. The principal causes of these variations have been identified and detailed blast monitoring techniques, including the analysis of muckpile fragmentation and shape, have been used to quantify the effects of explosive performance on blast Results.

Jan 1, 1990