Search Documents

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

By C OÆKeefe, A Thomas

Boom time in the mining industry has presented mill operators with several unique challenges including the need for increased throughput while being constrained by a shortage of skilled labour and aging capital equipment. New instrumentation technology that provides reduced installation costs; no process down time for installation; and reduced maintenance costs and labour requirements; has been introduced to address the labour situation while maintaining production. This new tech- nology also enabled more accurate and reliable process measurements thus providing the capability for operators to maximise throughput with their existing capital equipment. This passive SONAR based technology can accurately measure the volumetric flow rate of single phase and multiphase fluids as well as the amount of air entrained within slurries. This is accomplished in a non-invasive manner. This paper will describe the principle of operation as well as the application of the technology to critical minerals processing applications. Included will be operational examples comparing the SONAR measurement performance to traditional measurement techniques. These examples will include hydrocylone feed flow, flotation concentrate flow, and slurry streams containing magnetic ores. Actual plant data will be presented as well as a discussion on the operational advantages such a measurement capability.Also described will be the power of the technology platform to provide novel process monitoring and control capabilities such as pipeline sand-out prevention and pipeline acoustic monitoring.

Jan 1, 2009

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

By Smith E. L

The Ore Reserve/Exploration System implemented at Mount Isa for M.I.M. Holdings Limited is a comprehensive computer system designed to process assay, geological, structural and survey data input via special purpose logging sheets from daily activities at Isa Mine, Hilton Mine and various Carpentaria Exploration Company prospects. The system performs two basic functions; (1) data acquisition, validation and file maintenance to prepare the data for retrieval, and (2) generation of routine and optional reports. The types of reports available range from masterfile detail printouts and retrieval of data by key items to survey computations, structural analyses, cutoff calculations, statistical analyses and ore reserve calculations by the polygonal, inverse square or moving average techniques. The use of various optional reports available through the system is illustrated by several examples, and planned future development is discussed.

Jan 1, 1973

In comparisons of a trial extruded brick containing 33 per cent coalwash and 67 per cent clay and a trial pressed brick containing 100 per cent coalwash with a standard extruded clay face brick, the mixed feed stock trial brick compared favourably with the standard brick. If a highly plastic clay is used to mix with the coalwash, satisfactory results are obtained in respect to dimension, strength, water absorption, efflorescence, resistance to salt attack, hardness, colour, weathering, mineralogy and porosity. Although a brick containing only coalwash can be successfully manufactured in a press, its mechanical and physical properties are inferior. This mixed feed stock brickmaking technology leads to the utilisation of a by-product with a potential saving of raw material costs. The extent of use is likely to depend on the proximity of the coal washery and the brickworks and the economicsof transportation costs.

Jan 1, 1992

By Edwards A. B

The occurrence of gold so finely divided as to be invisible under the microscope, even at magnificatioIl; of 1,200 to 2,000 diameters, is rare, but not unknow;n.. Burg (1930) has described an occurrence of such "invisible gold" from the 25/37 vein of the Bradisor mine at Brad in the Siebengeburgen district of Rumania (Transylvania), in which the pyrite contained up to 150 grams of gold per ton (approx. 5 oz. gold per ton). Hoffman (1931) has described an epithermal silver gold ore from the Titiribi district of Columbia (South America), in which "invisible gold" to the extent of 150 grams per ton occurred in the pyrite, arsenopyrite and zincblende; and Haycock (1937) has recorded it in pyrite from the Surf Point mine (Canada), which contained no visible gold, but yielded positive testsfor gold whenever samples drilled from polished surfaces of apparently homogeneous pyrite were tested spectrographically.The examination of a cyanided pyritic concentrate, together with a sample of the ore from which it' was prepared, from the Dolphin East lode at Vatukoula, Fiji, carried out as part of the programme of the Mineragraphic Section of the Council for Scientific and Industrial Research, Australia, has established a further occurrence of "invisible gold" in pyrite and arsenopyrite. The Dolphin pyrite contains about 25 oz. gold per ton, and the arsenopyrite contains more than 33 oz. per ton.The concentrate has been prepared for the Mill Superintendent of the Emperor Gold Mining Co. by L. Mayger...

Jan 1, 1946

Efficient performance of pulp lifters to discharge ground rock is critical to the effective performance of SAG and AG mills. The paper covers developments in the design of pulp lifters and associated grates, of both conventional straight-radial and curved types, and of the inner discharge cone. Issues covered include the discharge performance of both the slurry and rock components of the discharge, reverse flow back into the mill through open grates and backflow down the pulp lifters of material that fails to discharge from the mill. The design experience is interpreted in the light of developments in particle flow modelling of the flow of charge in pulp lifters.

Jan 1, 2004

The initially cautious approach taken towards ground support and reinforcement at the Porgera Underground Gold Mine in the Highlands of Papua New Guinea has evolved rapidly in the two years since stoping commenced. The confidence to continue the evolution process has grown from an increasing knowledge of mining conditions as stoping has progressed, to the extent that reinforcement requirements have decreased by 50 to 75 per cent depending on local circumstances. Changes to mining practices have significantly assisted and influenced this process.Empirical observations of ground behaviour, assisted by a deliberately selective extensometer monitoring program, provided the stimulus for early changes to ground support and reinforcement practices. Further optimisation of the ground support and reinforcement effort is being pursued through an active monitoring, measuring and analysis program. Ultimately, situation rather than site specific design will ensure continuing high quality ground support and reinforcement installations. However, local structural and lithological factors will continue to become more critical as the optimum position is reached.

Jan 1, 1993

By M S. Gallagher

In todayÆs high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accuratebut flexible design thereby allowing operational managers to providealternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different; with falling prices and escalating costs,improved margins become the focal objective. There are many ways toachieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the Net Present Value (NPV) of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

Reservoir Engineering has developed into an art. One phase of this art is forecasting the futi. perf ormance of oil and gas reservoirs for property valuations. A discussion of the necessity for oil property valuation isgiven. A brief 'discussion of the four most common methods is included and the engineering method is explained in more detail. As an example of oil property valuations, a producing oil lease in Shackelford County, Texas, USA is evaluated.' The recommendations and conclusions arrived at frun the results obtained are presented.

Jan 1, 1962

Interactive data exploration is essential for visualising grade distribution and geological controls on orbodies. Quick and appropriate computer techniques for making daily 'value adding' decisions include routine imaging of numerical data suc

Jan 1, 1998

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

The accuracy with which block estimates are perceived is obtained by calculation of the kriging variance. This is dependent upon the model chosen for the semi-variogram of the deposit. For an extensive series of spherical semi-variograms the changes in the kriging variance resulting from various degrees of misassignment of the relative nugget effect are investigated. The results are reported as contour maps of percentage change in kriging variance as a function of the range and relative nugget effect of the true model.

Jan 1, 1985

The Antarctic Peninsula consists of accretion complex sedimentary and volcanic rocks, talc-alkaline magmatic are rocks, marginal basin sediments and extension-related alkali basalts, dominantly of Mesozoic to Cenozoic age. Metallic minerals have been recorded at "250 localities but two thirds of these are innocuous occurrences of Fe+Cu accessory minerals. The remaining -70 localities are related to hydrothermal mineralization processes. Metallogenetic associations identified are: vein and breccia-hosted Fe+Cu+Zn+Pb+Mo or Fe+Cu+Mo+Mn, shear-hosted Fe+Cu, volcanogenic Fe+Cu and pegmatite-hosted Fe+Cu+Mo+Mn. Anomalous Au, Ag, As, W and Sb also occur but are not of economic interest. Metallogenic zoning is unproven and genetic models are uncertain, possibly involving volcanogenic, epithermal to hypothermal vein and porphyry-type systems. Substantial field and laboratory studies are required to understand distribution and Genesis.

Jan 1, 1987

This paper deals briefly with the geology and mineralisation of the Ediacara Mineral Field, which is located about 300 miles north of Adelaide in the Mount James Range.The field was discovered sane time prior to 1872. Total recorded production for the field amounts to a few hundred tons of lead and 36 tons of copper. Re-listing of the field during 1961-62 led to its classification as a Mississippi Valley type deposit. Diamond drilling has partly outlined the spread of mineralisation and confirmed its stratiform distribution,Sources for the metals are suggested and various possible mechanisms. of deposition are described.

Jan 1, 1963

In 1953, Dr N Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from The Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of The Institute appointed a Committee consisting of H H Dunkin, Associate Professor of Mining Engineering, University of Melbourne (Convenor); E A Rudd, Professor of Economic Geology, University of Adelaide; J D Campbell, Chief Geologist of Western Mining Corporation; and the writer, to consider the report on this subject.In December 1953, the Committee submitted its frrst report to the Council and this report (reproduced here as an Appendix) was widely circulated among member companies and engineers, with an invitation to comment on the proposals. A large number of replies was received and studied.After studying the replies the Committee issued a second report, in part as follows:From these replies we have learned that the suggestions made in the frrst report of the Committee are unacceptable to most of those interested, on one or all of the following grounds:a. number of categoriesb. defmition of categoriesc. nomenclature.It is also apparent that all alternatives suggested in the various replies would likewise be unacceptable to the majority of those replying.As a result, we have come to the conclusion that neither this Committee nor any other could at present and in the present state of opinion on the subject make recommendations regarding classification and nomenclature of ore reserves which would be acceptable to a sufficiently large proportion of members.It seems to us now that the objective of a widely applicable and acceptable system of classification and nomenclature, one that could be endorsed by The Institute and ultimately become standard practice in the industry, requires more than compromise between present conflicting views... it requires first a foundation of substantial agreement on the essential facts, implications and range of ore reserve estimation. This does not yet exist and it is evident that much additional analysis of present practice and opinion must be undertaken before any further systhesis is attempted.

Jan 1, 1994

By Hanna P

Coal geologists are under pressure to minimise exploration expenditure, maximise interpretation confidence and produce the results often too soon. This pressure continues to increase as companies are forced to evaluate borderline economic deposits which are usually deeper and more hazardous, such as the Togara North and Togara South projects in Central Queensland.

Jan 1, 1998

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By A Cooper

The current financial climate has given rise to fears that falling mineral prices and tight credit will force mining companies to cut back on production and new project development in a bid to cut costs and conserve cash. However, a prolonged squeeze on global supply can have only one result: a massive and potentially explosive demand for metals in the not-too-distant future. A resurgent global economy will also generate dramatic new demand for oil and energy, with a return to higher oil prices likely. How then should the mining industry plan for the future? In-pit crushing and conveying (IPCC) could lead the way as a partial or complete substitute for trucks. In 13 of 15 studies undertaken by Sandvik and Snowden, comparing IPCC with truck-optimised pit designs, IPCC generated operating savings ranging from US$0.18 to US$0.82 per tonne moved, compared to trucks. Trucks have higher operating, maintenance and energy costs than conveyors. New emission standards on diesel engines may make them more emission friendly but less efficient in terms of energy usage. With far more efficient energy use and cheaper operating costs per tonne moved than trucks, conveying offers an attractive alternative for the bad times ahead and into the apparent energy depleted future. When evaluating alternatives, a reasonable first step would be to conduct a scoping level study which analyses the differences in capital and operating costs between a truck and shovel operation and an IPCC solution. The study can also determine what type of IPCC is best suited to the particular mining application. The results can then be used to decide whether a more detailed study is justifiable. IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations. Sandvik (as an OEM with a full suite of IPCC equipment) can undertake these studies in ten working days in conjunction with Snowden or any other independent mine planner who knows how to schedule for IPCC. Because most mining industry personnel have been æborn and bredÆ on trucks and shovels û this paper focuses on some of the practical considerations necessary to make IPCC systems work that the Sandvik Technical Services Group has encountered during these studies.

Jan 1, 2009