Search Documents

By Hungerford F

Long-hole drilling technology has rapidly advanced this decade beginning with rotary drilling/pump down camera surveying and culminating in down-hole motor drilling with cableless electronic surveying over the past two years. With the latter system, a high level of directional control is achievable in boreholes up to 1000m long. Past long-hole drilling across the industry has seen a mixture of success and failure. With these experiences, new and improved techniques and equipment have evolved. A number of long-hole drilling options are available as variations on the basic rotary and down-hole motor methods. They involve different levels of cost and equipment and vary in their suitability in different geological environments and definition of targets. Long-hole drilling is mainly target applied, either in defining geological structures in greater detail, or proving important mining areas such as longwall blocks, to be free of structures. Successful drilling hinges on a combination of drilling expertise, quality and appropriateness of equipment, understanding of geological conditions and good colliery support. Drilling expertise forms part of sound interpretation through keeping relevant records, understanding the reasons for changes in drilling conditions and implementing specific tests such as coring. The final interpretation builds upon all other available geological information. There is still scope for research into improved techniques and equipment. The use of long boreholes for geophysical surveys has high potential.

Jan 1, 1988

The results of iron ore exploration in Western Australia between '1961 and 1964 are outlined, with particular.reference to the Hamersley Iron Province. Exploration during: these three years has increased the known resources of the-,Statle from 275 million tons to almost 9,000 million tons of high- grade hematite ore. In addition, reserves of lower-grade .pisolitic limonite ore are-estimated to amount to 6,000 million tons. The origin and characteristics of the different types of ore is discussed,

Jan 1, 1964

By S Corbel, P J. T Donchak, W Gorczyk

The Hodgkinson Province numerical modelling project aims to develop an improved understanding of the physical conditions that lead to the localisation of goldbearing fluids within known systems and apply this understanding to the prediction of potential new sites of gold mineralisation. The project follows a series of stages from identifying the key parameters required to construct and test simulations through to reverse engineering of known deposits and ultimately applying the conditions identified in the preliminary stages to predictive simulations. Results of the modelling demonstrate strong geometric controls of the localisation of fluids during mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The planning, design and construction of a service tunnel, under a major arterial road between two hospitals are described. The multiple uses of the tunnel combine to provide a favourable cost-benefit ratio for the tunnel as part of a rationalisation of services between hospitals. The driven tunnel provides economic, program and approval advantages over that of a cut and cover construction. The cross sectional shape of the tunnel was determined during feasibility studies by the degree of weathering of the Silurian mud- stones, the shallow cover and the proposed excavation equipment as well as the functional requirements. The site investigations covering geotechnical, building, noise and level surveys provided input to the design documentation and construction phases. Monitoring of settlement levels and primary support stresses during early construction stages confirmed the adequacy of the proposed tunnelling methods and support to be used adjacent to the major building foundations. The 140 metre long tunnel was success- fully completed in April 1980 at a cost of $650,000.

Jan 1, 1981

In many mining operations, the truck and loader equipment represents the bulk of the invested capital and the majority of the mine operating cost. The profitability of these mines is therefore critically linked to the efficiency of the truck and loader operations. The various factors which affect the productivity of trucks and loaders are analysed by computer simulation, and the results presented in a form allowing assessment of the importance of each factor on overall productivity.

Jan 1, 1983

By Russell J

A sustained drop in the grade of Mount Isa lead-zinc-silver ore occurred in mid 1980. It was decided to increase concentrator throughput from 200 000 to 240 000 tonnes/four week period to maintain budget metal production. To achieve this increase whilst maintaining acceptable grinding and flotation performance, crushing plant final product size had to be reduced from 100%-13mm to 1000-11.2mm. The goal in the crushing plant was to achieve a 20% increase in throughput with a 20% decrease in the top size of the product. This was achieved by operational changes to improve plant availability and optimisation of the existing crushing and screening equipment Performance.

Jan 1, 1978

By R C. Morris

Supergene lateritic iron ores are uncommon when compared with the vast tonnages of BIF-hosted microplaty haematite ores of the world or with the dominant supergene mimetic martite-goethite ores of the Hamersleys. In Australia and to a lesser extent in India and South America, mimetic replacement of gangue minerals by iron hydroxyoxides is a major factor in forming supergene iron ore from banded iron-formation (BIF) and results in the superb preservation of all of the original BIF features. This includes primary banding down to the finest inclusions, as a result of pseudomorphing of the BIF gangue at depth by goethite. The enrichment as a whole is an absolute accumulation of Fe at depth, dissolved from the surface BIF, and a removal of the gangue elements without loss of the original BIF mineral textures. Thus the ores grow upward to meet the downward destruction of the surface BIF by erosion. By contrast the supergene lateritic ores including the 'blue dust ores' are residual ores resulting from the relative accumulation of Fe. In the supergene lateritic ores derived from BIF, removal of the gangue is accompanied by repetitive solution and reprecipitation by secondary haematite and goethite. The final product of lateritisation of BIF and BIF-derived ores is typically complex, due to successive overprinting of earlier stages of alteration during the process, and because of the different precursors. This progressive lateritic modification tends to produce a varied surface complex including massive, vermiform, and botryoidal, or nodular aluminous/siliceous goethite and haematite, variously known as ferricrete, duricrust, canga, or 'hydrated zone hardcap'. The significant difference in these ores to the supergene mimetic martite-goethite ores is that they grow downward, with the total destruction of any of the parent BIF or BIF-ore textures.

Jan 1, 2009

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

The introduction of on-stream analysis in flotation circuits has raised the possibility of automatic control of flotation performance by digital computers. The development of control strategies for an industrial zinc cir- cuit is discussed with reference to identifi- cation of the major disturbances, investigation into the performance of the circuit, the design of the control algorithms, the testing of their performance and their implementation in a production environment.

Jan 1, 1983

By Bearman R. A, Parkin R. M

Traditional quality control procedures for aggregates production within the quarry industry rely on off-line laboratory analysis, resulting in poor performance and inconsistent product quality. A high speed on-line aggregate classification system is described here. A product sampling system directs aggregate through an inspection chamber where a novel imaging system digitises the particle geometry. Data processing algorithms extract dimensional data and image features, while a neural network classifier assigns a qualitative shape descriptor to each rock particle. This system provides each sampled batch with a complete analysis of size and shape distributions, complementing a new generation of cone crusher technology to maximise product quality and plant efficiency.

Jan 1, 1995

By Alder KF

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials. This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products. This paper presents some predictions of the possible growth of nuclear power installations in Australia. These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50% of new generating plant might be nuclear. Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme. - The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel'; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1970

The "Line of Lade", a generic term by which the great Broken Hill orebodies are collectively known, lies in the County of Yancowinna, New South Wales (NSW) at the south eastern extrenity of the Barrier Ranges. As the township of Broken Hill grew to a city (incidentally it was officially named Willyama but by exerting an enterprising community independence which is still evident today it outplayed officialdom and retained its descriptive name), two major areas of population developed, Broken Hill and South Broken Hill. These two main civic divisions are respectively north west and south east of their dividing line, the surface expression of the orebody. See Fig. 1. The border between the States of NSW and South Australia (SA) is drawn along longitude 1410 East whilst the city of Broken hill's official longitude is 1410 28' 14" East which means it is only 50 km from this political boundary. A latitude of 310 57' 03" South contributes to the harsh climate of high summer temperatures which is not mollified by any significant increase in altitude for Broken Hill is only 300 m above sea level.

Jan 1, 1983

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

The Wild Dog gold-silver-copper deposit represents a new ore-deposit type in Papua New Guinea. The telluride vein mineralisation is associated with a Tertiary caldera and has similarities with that from the Baguio district, Philippines, Vatakoula, Fiji, and the San Juan Mountains, southwestern Colorado. The deposit, discovered in July 1983, has negligible stream silt and concentrate anomaly, and a float-train limited to within 300m of the prospect. The comparatively recent exposure of the vein system may explain the limited stream expression of the deposit. At least three major veins occur in the deposit; the vein system strikes north- northeasterly, dips 78¦W, and has a maximum strike length of 1350m. Veins are enveloped by a wallrock dominated by an assemblage of quartz-illite-pyrite. Four types of silicification related to multiple vein filling events have been defined on the basis of field relationships, drill-core intersections, petrology and fluid inclusion study. To December 1986 a total of 22 diamond drill holes (2304m) and 40 reverse circulation drill holes (1833m) have been completed on the deposit, defining a 750m zone of interest. The upper 30m of the deposit is oxidised. Much of the high-grade mineralisation in both the sulphide and oxide portions of the deposit is restricted to ore- shoots which strike parallel to the overall vein structure and are vertical to steeply westward dipping. They are defined geochemically by the lg/t Au cutoff and geologically by the relative increase in the vein density of auriferous grey-black sulphidic silica, the final vein filling event. Metallurgical studies and the results of close-spaced drilling have demonstrated the very good repeatibility on duplicate assays, and the extremes of grade variability of mineralisation over very short distances. The good assay agreement on duplicate samples .s indicative of fine, dispersed gold.

Jan 1, 1987

By Yushan Ma, Jiqing Wang, Hanyi Jia

The Hedong Gold Mine is located in the Yantai area, Shandong province, China. It is an underground mine with an annual gold output of some 700 000 grams. The orebody is located on the edge of the Wanger Shan metamorphism zone, and the hangingwall of orebodies is thus defined by a prominent set of fractures. The proximity of the metamorphism zone and the inclusion of the fracture set ensure that both the orebody and the country rocks are unstable. The main orebodies dip at an angle of between 40 to 45¦, with a strike length of 160 metres and a horizontal width of 50 metres. Surface subsidence in the area is not permitted. Cut and fill mining is usually practiced. As the mining operation proceeds to greater depths, the ore grade is diminishing and it is necessary to find a more efficient stoping method. Sublevel open stoping with sequential extraction and filling of each sublevel has been designed and applied in situ. This new mining method is called æsublevel open and fill stoping methodÆ in the mine. Experience to-date is that new mining method is satisfactory.

Jan 1, 1998

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

The word governing derives from gubernare meaningto pilot a ship. Being inclined to metaphors, one could be forgiven to think that politicians act this verb and captain the Nation's ship into some definite course. In the case of at least the mineral resources industry, it seems that there are not many James Cook followers in our parliaments: Australia's approach to mineral and energy policy is often chaotic - witness the 1935 to 1961 ban on iron ore export-ing which prevented the development of a significant steel industry at time when the World was hungry for this metal, just to mention one amongst many other examples.The follies of Australia's mineral policies are well il-lustrated in the case of uranium mining. Although Australia had the Western World's largest economic reserves of uranium, it is onlythefifth producing nation and its uranium potential is largely unrealised. At the root of this situation are the interventionist attitudes and policies of successive Federal Governments which for more than four decades distorted the Investment decision and, in more recent times. discouraaed investment.

Jan 1, 1990