Search Documents

By P G. Fuller

The Woodlawn Mine near Canberra faced the challenge of poor ground conditions from the commencement of underground operations 1987. Talcose shears bounded the dense massive sulphides on both the hangingwall and footwall side of the orebody. In another area the talc existed not only on the edges of the orebody but through out it as well. The country rock was relatively weak shales compounded by a low stress environment that allowed the wall rocks to fall apart quite easily. The challenge for the operators was to overcome the poor ground conditions. This was done by attacking the problem from three directions:technology, how technology is applied, human relations and leadership by all levels of the Management team, and by ensuring that these processes meshed together well.Woodlawn in it early days as an underground mine enlisted the assistance of BFP (Formerly Barrett Fuller and Partners) as a second set of eyes to assist with the assessment of the ground control procedures. The results are discussed in this paper. The progression to this end result included:non-contract payment systems; ground control training for the full range of mining personnel; the development and enhancement of cable bolting and shotcreting equipment; the development of Practical Standard Work Procedures by mine operators; and innovative use of shotcrete and cables bolts to control extremely poor ground conditions.

Jan 1, 1998

By O Otgonbayar, B Bayarmaa, D Batbyamba, S Amar-Amgalan, K H. Natsagdorj, J Nomin-Erdene, B Boldkhuu, T S. Sainzaya

The Argyle deposit in the Kimberley region of Western Australia was the world’s largest accumulation of natural diamonds. Following its discovery in 1979, the mining of associated alluvial diamonds commenced in 1983, followed by the pipe in late 1985. Over the life of the mine to its closure in November 2020, Argyle produced approximately 900 million carats of diamonds. Argyle diamonds are distinctive in having a predominance of brown colours and rare highly-prized pink diamonds, which are a signature of the deposit. The 3D geological model developed from mining and deep drilling shows that Argyle is a composite pipe formed by the coalescence of several steep-sided diatremes, each with their own feeder zones at depth, that were erupted along a NNE-trending fault. The ~1.2 Ga Argyle pipe is comprised of diamondiferous olivine lamproite volcaniclastic rocks and intruded by sparse olivine lamproite dykes. The volcaniclastic rocks are predominantly comprised of unconsolidated quartz-rich lapilli and coarse ash deposits formed by numerous phreatomagmatic eruptions of olivine lamproite magma through Mesoproterozoic water-rich sands and silts. Post-emplacement deformation has tilted the orebody 30° to the north and regional strike-slip faulting has offset, segmented, and elongated the orebody. Recent significant modifications of the geological model resulted from underground block cave operations, producing several critical lessons learnt. Diamond grade and quality reconciliation issues warranted a geological investigation which resulted in the recognition of new volcaniclastic olivine lamproite domains with a broad range of diamond grades, including some very high-grade units. The new lamproite domains had a significant effect on the block cave mining and resultant recovery of diamonds. The new findings enable a more coherent and detailed geological understanding of the volcanic emplacement and paragenetic sequence of the Argyle AK1 pipe. Structural modelling of the deposit also played a major role in the block cave mining tonnage recoveries and daily operations. The re-examination of the geology of the Argyle pipe and the results of this new information reinforces the need for ongoing robust geological work both in the early stages of mining a deposit and continued during the life of the mine.

Mar 22, 2022

By Lynn DR, Wadley GB

The Australian gold industry has made large steps forward in the last few years. This progress has been driven by improvements in mining and processing technology, the high price of gold and by a favourable legislative, political and taxation environment. This paper concentrates on improvements in gold project development, process engineering and technology as seen by BHP Engineering, Perth, Australia.The paper describes technical aspects of successful gold project development including metallurgical testwork, feasibility studies, choice of process flowsheet (gravity, heap leach, carbon in pulp (CIP), carbon in leach (CIL) or other routes). It sets out our views on plant design, plant construction, procurement and project management.A case study for a small plant recently completed in the Philippines is presented as a solution to the problems often encountered in treating quartz vein gold deposits.

Jan 1, 1990

By B Goebel, G Baker

The Australian Magnesium Corporation Limited (AMC) is constructing the worldÆs largest magnesium metal plant at Stanwell, 24 km west of Rockhampton in Central Queensland. The $1.3 billion, 97 000 tonne per year plant is scheduled to commence production in mid-2004. It will produce magnesium from magnesite using the innovative, locally developed AM Process Technology which enables magnesium to be produced at internationally competitive costs. The technology will enable the plant to have the lowest environmental impact of all the available magnesium production processes. The project will meet current world-best-practice environmental and emission standards while on a life cycle analysis, magnesium produced by the Stanwell plant will result in net reduction in global greenhouse gas emissions. Magnesium is the lightest of the structural metals. Its high strength to weight ratio and ease of casting and machinability makes it particularly suitable for the manufacture of light weight automotive components. Reducing the weight of motor vehicles through the use of light weight materials such as magnesium is the current primary means adopted by the automobile manufacturing industry to improve motor vehicle fuel efficiency and the lowering of emissions of greenhouse gases. The Australian Magnesium or AM process has been developed over the past decade by AMC in conjunction with the CSIRO to produce magnesium from magnesite mined at AMCÆs Kunwarara deposit. Over $200 million has been spent developing the AM process, designing, building and operating a demonstration plant at Gladstone and to complete an environmental impact statement and receive environmental approvals as well as funding for the commercial Stanwell Project. The paper outlines the development of the AM process technology, the operations of the Gladstone demonstration plant confirming the process technology, its operating costs and environmental performance. The paper covers the particular attention that was given to minimising the production of CHCÆs, the development of new cover gases for molten magnesium, the minimising of emissions of greenhouse gases and the life cycle analysis of magnesium as a replacement for steel and heavier metals in motor vehicles which confirmed its use resulted in a net reduction in global greenhouse gas emissions. The project received both Commonwealth and Queensland Government environmental approvals by August 2000.

Jan 1, 2002

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

By R Dimitrakopoulos

Optimisation and mathematical formulations for open pit design and long-term production scheduling have been available since the 1960s. There are two main concerns in the application of existing mixed integer programming (MIP) models in open pit mines: a. the feasibility of generating both optimal solutions and practically mineable scheduling patterns and b. the inability to deal with in situ variability in orebodies and account for uncertainty. In dealing with these issues, a general open pit production scheduling method for multi-element deposits is presented and subsequently used to optimise the long-term production schedule in a nickel laterite deposit. The application shows the weaknesses of MIP formulations in terms of generating optimal solutions as well as practically feasible mining patterns. The application of the same formulation in the presence of in situ orebody variability and uncertainty uncovers a major reason for deviations of scheduled production from actual production, and outlines additional limits of traditional optimisation formulations as well as future needs.

Jan 1, 2003

By D Giurco

This paper presents the results from research undertaken in the CSIRO-funded Mineral Futures Collaboration Cluster on developing a future vision for the mining and minerals industry – Vision 2040 – in which the industry proactively contributes to long-term benefit for communities and the nation. Our research finds that Australia is currently experiencing mining-led prosperity due to high commodity prices, yet underlying this are challenges for maintaining market share due to lower productivity from extracting lower grade, more remote and complex ores. Whilst much focus has been on developing new technologies for finding and processing such ores, this paper assesses these activities, together with policy and market innovations in the context of needing to strengthen social, environmental and financial capital for long-term benefit. Vision 2010 sees mining activities linked to systems that are net providers of clean water, energy and ecosystem services, rather than minimising negative impacts alone; sovereign wealth funds are used to harness current prosperity for future innovation. Using a case study in lithium and comparisons to iron/steel, coal and copper – we illustrate the opportunities for new technology, policy and market innovations to link the mining and minerals sector in Australia to more sustainable patterns of production, consumption and prosperity.

Nov 22, 2011

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By J Burgess, G Scanlan

In 1993 after over 110 years of mining operations, production ceased at the Broken Hill North Mine. Following the cessation of operations a rehabilitation program was developed to satisfy the requirements of the various government departments. This program has been implemented progressively since mine closure. The paper will discuss: primary aims and objectives of the rehabilitation program, implementation of the program, rationale behind rehabilitation objectives, and problems encountered in implementation of the program. To-date the primary rehabilitation of the mine has involved the capping of redundant tailing dams with inert waste rock to prevent the contamination of the receiving environment. A Water Management Plan has been developed to contain all run-off from the mine area in an extreme storm event. A cultural heritage assessment of the leases has been undertaken to ensure the rehabilitation is consistent with the historical significance of the site and community expectations. All redundant material from the mine has been sold in a æno reserveÆ auction and the workshop area has been relocated to the Southern operations. At present the only active areas on the mine are a maintenance area for equipment for the Potosi open pit, and a primary crusher for Potosi ore which is railed to the Southern operations for further processing. Upon completion of the rehabilitation program, Pasminco Broken Hill Mine intends to relinquish the mining leases to the Department of Mineral Resources.

Jan 1, 1998

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

By Upfold RW, Nguyen VU

The extraction and utilisation of metals and materials is the basis of modern civilisation, and will remain so for many decades, Traditional metals are facing some challenges and research is needed in specific areas, to improve metal extraction processes, to develop processes for newer metals and minerals, and to develop new applications, The shortage of metallurgists now becoming apparent in Australia is a further significant problem that needs urgent attention, and much more publicity is required for the Mineral Industry, as well as for the utilisation Industries,

Jan 1, 1986

By W Angerer

This paper describes the design of the marine riser structures, including the design measures for sealing and protection from flooding, dewatering and connection to the main tunnels, for the Gold Coast desalination plant in Queensland. The risers connect the intake and discharge tunnels to the ocean. Construction commenced on both in April 2007. The paper describes the key design criteria for the risers, the construction constraints that influenced the design and the design of the main elements of the risers and the connections to the tunnels.

Jan 1, 2008

By Whiten W. J

The control of mineral processing plants incorporates a number of off-line and on-line actions by plant personnel to obtain satisfactory plant performance. In general, off-line actions centre around intensive data analysis, while on-line activities are either automated control actions or prompted by qualitative interpretations of quantitative and qualitative information. Data sets obtained by various data logging devices and laboratory analysis of samples in many modem plants may be very large and are often unmanageable. This paper presents a method of analysing the data sets typically found in mineral processing, based on cluster analysis. The results of this analysis leads to a more complete understanding of operations in comparison with existing analysis tools used in mineral processing.Improved process configuration, optimised control strategies and in some cases, direct use of the results in monitoring process unit operations may be achieved.

Jan 1, 1992

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

The Regional Development Council has initiated a project that aims to find better ways for further investment by extractive industry companies in sustainable regional and community futures. It will be undertaken through collaborative actions that bring together the resources of private and public sector stakeholders in regional Western Australia.   The broad objectives of the project are to: describe and analyse the current situation with respect to the impediments to regional communities being more self sustaining, assess the effectiveness of the current and possible future levels of investment by extractive industry companies in the sustainable development of communities in regional Western Australia, identify and demonstrate collaborative ways in which extractive industry companies in Australia and other countries can play an enhanced role in sustainable regional and community sustainability through strategic engagement and investment; and confirm the effectiveness of the collaborative measures in delivering sustainable outcomes for regional communities by way of attracting and retaining populations and enterprises in Australia and similar environments.

Jun 1, 2010

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

During the past 18 months several import- ant hydrocarbon discoveries have been made in the Dampier Sub-basin, which is a sedimentary area lying entirely offshore from the Precambrian Pilbara Block in the southern part of 'he Northwest Shelf of Western Australia. This sub-basin is a major sedimentary downwarp forming a northern extension to the Carnarvon Basin. This extension is bounded to the north by the De Grey Nose, separating it from the Beagle Sub-basin. To the south the Dampier Sub-basin merges with the Barrow Sub- basin. Extensive seismic data combined with results from exploration drilling show that the Dampier Sub-basin is a complex depositional basin containing over 20,000 feet of sediments which are mainly Triassic to Recent in age. Tectonically the sub-basin can be divided into seven main structural elements. In a northwest to southeast direction these are the Rankin Platform, the Kendrew Trough, the Madeleine- Dampier Trend, the Lewis Trough, the Legendre- Rosemary Trend, the Enderby Fault Zone and the broad Pilbara Shelf. Permian sediments were encountered in only one well drilled to date in the sub-basin, but Triassic and younger sediments are extensive. The section consists initially of 'hi -_D 7 ri ,~ ~, , i , Derived

Jan 1, 1973

By Gillies A. D S, Supriyadi

The landed cost of coal to the international customer is a major parameter which determines market competitiveness. Rail, port and shipping charges represent 30 to 50 per cent of landed costs for Australian mines selling to Asia. This prop

Jan 1, 1994

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991