Search Documents

By M Thomas, S Lambert

The Tugun Bypass Tunnel in Gold Coast, Australia was constructed using diaphragm walls with the top-down cut-and-cover method to allow simultaneous construction of an airport runway extension above the tunnel, whilst excavation of the tunnel continued underneath. The tunnel was built in an environment of high groundwater table and deep deposits of alluvial and estuarine soils with the toes of the walls founded in soil deposits. There was a potential risk for differential settlements to occur between the diaphragm wall panels, caused by the runway fill placed over the tunnel roof during excavation. Dewatering within the diaphragm walls was required to facilitate the construction of the tunnel. The tunnel was also built in an area where environmental considerations were of great importance. Three-dimensional numerical modelling was undertaken to predict the differential settlements of the tunnel with considerations of varying subsurface profile, staged excavation and dewatering, non- uniform surface loading and complex soil-structure interaction. Field instrumentation and monitoring was implemented to confirm numerical predictions.  

Jan 1, 2008

By Carter A. C

The increasing need for alternative energy sources as well as the less clearly perceived but equally increasing demand for non-fuel minerals has resulted in extensive exploitation of near surface deposits. Many such deposits have depleted reserves and mining corporations are increasingly turning their attention to deposits, with thicker overburden, less competent materials, steeper dips and more complex structure. These deposits pose mine layout, geotechnical and equipment problems as well as the need for large outputs to achieve economies of scale. The paper describes the major problems and operational solutions for such deposits using continuous excavation and transport equipment.

Jan 1, 1980

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

By C Staak, H Mischo, A Fichtner, F Reuter

In mining and remote areas of resource industry, there has been a development towards lacking emergency medical first aid response, that creates a potential disadvantage for patients after work accidents and other medical emergencies compared to standard population. This raises the question how a professional emergency medical coverage can be provided underground, taking into account lacking medical professionals in small resource companies combined with long rescue times. Aiming on the closure of this gap, a team of the mine rescue brigade from the Research and Training Mine Reiche Zeche (Forschungs-und Lehrbergwerk (FLB) Reiche Zeche) of the TUBAF Technische Universität Bergakademie Freiberg in Freiberg/Germany and its cooperating emergency departments of the Freiberg District Hospital and the Zeisigwaldkliniken Bethanien Chemnitz developed a totally new rescue concept using elements from tactical medicine and advanced emergency medicine combined with a specifically designed compact equipment and a highly standardised teaching curriculum. A fully new standardised and condensed tactical medical approach was developed including specifically adjusted equipment, and was taught in a didactically optimised way within 16 lessons in two days. Objective Structured Practical Examinations (OSPE) using manikins and simulated patients were conducted and compared to the identical exam of the reference group, which consisted of advanced paramedics. The standardised tactical medical scheme includes vital functions and body checks, advanced life support, nasal and intraosseous drug application, supraglottic airway management, artificial ventilation, thoracocentesis, bleeding control including tourniquet, fracture repositioning and splinting, transport bedding and thermal preservation. The developed Tactical Medical Mining Rescue (TMR) concept was subsequently included in the German guidelines for mine rescue services in 2022 and is already implemented in many companies in Germany and several international projects.

Sep 1, 2024

By Brouwer G, Shaw J

As South African gold mines go deeper, and improved and more uniform working condi- tions are required, ever larger amounts of refrigeration are needed. At the same time new and more suitable cooling equipment is becoming available for use with new mining layouts as well as on existing shaft systems. The advent of the large diameter rotor screw compressor has meant that there is now a machine available with great flexibility in performance and construction for efficient underground use. The first installation using this type of machine is described.

Jan 1, 1988

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By J Q. Shi, M Karakus, Y Liu

Predicting the spatial distribution of rock mass properties in cave mining is a critical challenge. In this study, we introduce a novel machine learning-based model to advance our comprehension of rock behaviour. This model specifically focuses on the spatial distribution of rock mass and mechanical properties, a crucial aspect of our understanding of rock mechanics. Our model is inspired by the recognition that neighbouring information serves as crucial prior knowledge for predicting the spatial distribution of these properties, wherein closer neighbours are likely to exhibit similar characteristics. To effectively capture and model these neighbour relationships, we design a neural network-based model to map the spatial locations within the data set into a new highdimensional space. Within this transformed space, we utilise Euclidean distance to identify N neighbours. Leveraging these neighbours, we introduce a straightforward yet highly effective approach—label propagation—to construct a graph that illustrates neighbour relationships. This graph not only facilitates the prediction of the spatial distribution of rock mass properties but also offers a measure of uncertainty for these predictions. We validate the proposed method using a real rock data set and showcase its efficacy in capturing intricate relationships and distributions within rock properties, enabling precise predictions across diverse spatial scales. Our results underscore the potential of machine learning-based approaches to revolutionise the field of rock mechanics, providing valuable insights applicable to geotechnical engineering, mining, and other sectors where an accurate understanding of rock properties is paramount. This model has direct practical implications, offering a new tool for geotechnical engineers and mining professionals to enhance their understanding and prediction of rock properties, thereby improving safety and efficiency in their operations.

Sep 1, 2024

Fluid bed sulphation roasting of bismuth concentrates began at Warrego in 1980 in con- junction with the recommissioning of the Tennant Creek Smelter. This process, develop- ed by Peko Mines, is used to separate copper and bismuth by converting copper minerals to a water or weak acid soluble form and then leaching. Pilot scale testwork conducted at the Australian Mineral Development Laboratories (AMDEL) and by Dorr Oliver Pty Ltd in the USA indicated that close control of bed teaper- atures and exhaust gas composition was required to ensure high levels of soluble copper. After overcoming some initial problems, the plant now achieves typically 89 percent copper extraction. Plant capacity is 2.7 tonnes/h by design but in practice this is limited by feed analysis, air requirements, cyclone operation and calcine particle size Consideration.

Jan 1, 1984

By V Sahajwalla, S Shin

Research activities to classify the quality of iron oxides have a long history but most of such activities are for the existing processes such as blast furnace or DR plant. Therefore the newly developed process, such as the COREX process, needs new standardisation although some basic functions of the new process have similarity to the existing processes. Many researchers (Hauk, 1990; Cho et al, 1998) in the field of COREX process have conducted investigations since the early stages of the process development and activities are underway for further plant optimisation. As Agrawal and Oshnock (1995) pointed out, because coke is not included in the COREX reduction shaft the strength requirement of the feed materials in COREX process will be more demanding than that in the blast furnace. This condition is similar to Midrex DR plant but the main reduction gas of COREX plant is carbon monoxide generated from coal combustion while that of Midrex DR plant is hydrogen from natural gas.

Jan 1, 2000

The progress between 1983 and 1989 towards Management Guidelines for R16 was extremely slow and painful because protection of the mining heritage was a new function and administrative activity not referred to in any Queensland mining law. Also, until 2 December 1989 the Queensland political climate was anti-preservation. Therefore an understanding had to be achieved between John Hay, the Mines Department and the National Parks and Wildlife Service, to ensure preservation of the mining machinery in situ rather than being removed to a town site such as in Ravenswood.

Jan 1, 1990

By Collins AR, Meares RMD, Graham JM

Exploration programs for both alluvial (placer) and hardrock platinum group metal deposits are being conducted in Papua New Guinea by a joint venture between Degussa AG and Pancontinental Mining Limited. Prospective areas were defined on the basis of ultramafic/ophiolitic source rocks shedding detrital platinoid grains. Field sampling techniques including churn drilling, together with appropriate laboratory analytical and mineralogical techniques, were developed and are contributing to the success of the exploration programs.

Jan 1, 1987

By Mirabediny H, Whitchurch K

A computerised simulation model has been developed to select the most suitable digging method of a dragline operation for a given geological condition. The developed procedure uses a geological ore body model as the basis for the geologic database. The simulation selects the most cost effective dragline digging method from a database of various dragline digging methods The database consists of common and innovative dragline methods currently used in Australian open cut mines. A generalised computer package, DSLX, was extensively used to simulate various dragline digging methods. The DSLX software uses predefined functions to build strip geometry, working benches, blast profiles and spoil piles. The outputs from DSLX in form of volumetric, swing angles and hoist distances data are then aggregated with dragline specifications and site time study data to compare productivity of selected digging methods. The result of a case study showed that this procedure lends itself to the 'optimum' selection a dragline digging method for a given coal deposit.

Jan 1, 1995

By Brasnett TC

A wide variety of problems are encountered on a day to day operating basis in the Isa Mine Concentrators. These vary from complex textural problems in the lead-zinc concentrator and their subsequent effect on grinding and flotation to scheduling of converter slag treatment in a chalcopyrite concentrator. With the advent of process control, metallurgists need to specialise and keep up to date with technology improvements. This paper will attempt to describe the significant problems'faced by a Metallurgist û Control.

Jan 1, 1978

By N J. Beukes, J Gutzmer, C Reinke, M Bau

In this study the light sparse phase search (SPL_Lt) mode on the Mineral Liberation Analyser (MLA) was successfully used to identify and quantify the abundance of rare earth element (REE) phosphates in Precambrian iron formations. Monazite (light REE phosphate) and xenotime (Y and heavy REE phosphate) are identified and data from the MLA combined with the mineral chemistry of the two minerals are used to calculate and model the expected REE concentration and distribution in these two REE phosphates. The REE phosphates account for up to 31 per cent of the REEs in the banded iron formations (BIFs) and excellent correspondence is observed between the modelled REE patterns and the whole rock geochemical data available for the same samples. Except for quantifying the mineral weights, the sparse phase search also allows for the localisation of REE phosphate grains and the observation of their association with other minerals using backscatter electron (BSE) imaging. These observations are used to conclude that the REE phosphates were most likely of diagenetic origin, with REEs and phosphate remobilised from primary chemical precipitates. It is demonstrated that automated mineralogical techniques can be used to qualitatively and quantitatively describe the influence of a rockÆs trace mineralogy on its geochemistry.

Jan 1, 2008

By S F. Wang, J J. Yin

Dust pollution poses a persistent challenge within mining processes, giving rise to a spectrum of concerns, including occupational diseases, mechanical degradation, diminished visibility, and the potential for dust explosion incidents. Existing dust detection and monitoring methodologies face limitations, including insufficient measurement accuracy and intricate processing procedures. Consequently, a comprehensive identification and evaluation system rooted in image processing technology is proposed to facilitate real-time measurements of dust pollution in mining worksites. The study primarily employs grey scale average and fractal dimensions to characterise particle features evident in collected dust images. As a result, the data processing platform can dynamically process data and present dust pollution conditions. Notably, this research integrates the monitoring and assessment of dust pollution with the systematic adjustment of mining parameters, ventilation parameters, and strategies for dust reduction. Through statistical analysis of dust concentration and particle size during mining processes, rock properties such as components and cuttability can inform mining parameters. This information, in turn, guides detailed excavation strategies, including cutterhead speeds, torque, and excavation speed. Similarly, analysing dust characteristics derived from images is a valuable resource for gaining deeper insights into the efficacy of implemented ventilation strategies. By harnessing vision-based information detailing dust concentration and distribution, a wealth of direct guidance becomes available for refining ventilation parameters. This encompasses crucial aspects such as the selection of appropriate ventilation systems tailored to the specific mining environment and the optimisation of operational conditions for ventilation fans. Additionally, the detailed information derived from the visual data allows for strategic decisions on factors like the spatial arrangement of ventilation outlets and the calibration of airflow rates. Moreover, precise choices for dust reduction measures and parameters can be made based on the prevailing dust conditions. Upon real-time monitoring of dust pollution using the proposed method, corresponding measures such as spraying and foaming can be promptly implemented. Crucial parameters, such as spray angles and volume, are integral to these application processes. In essence, the proposed method assumes a pivotal role in not only dust monitoring but also the formulation of preventative and control measures within mining processes.

Sep 1, 2024

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

By Rowley M, Bradford P

Plutonic Resources Limited (formerly known as Pioneer Mineral Exploration Limited) delineated, developed and operates the Plutonic Gold Mine located 180 kms northeast of Meekatharra, Western Australia. Gold mineralisation was discovered in the Marymia greenstone belt by Great Central Mines NL (GCM) in 1988. There was no previous, recorded gold mining activity in the area. In May 1989, Plutonic Resources Limited (PRL) entered into an agreement to acquire a 51 per cent interest in the three Mining Leases containing the Plutonic deposit from GCM. Subsequently in December 1989, PRL acquired the remaining 49 per cent interest in the Mining Leases. PRL and GCM are also involved in a 51:49 regional joint venture on extensive Exploration Licences in the vicinity of the Mining Leases. Following due diligence validation, reserve delineation and testwork, a feasibility study was undertaken in conjunction with JR Engineering Services, which led to the financing and development of the project for operation in August 1990.

Jan 1, 1991

Wire rope, when used for hoisting on a mine is the weak- est and most vulnerable unit in the most expensive'-group of installations or! the mine. With the introduction' of hoisting on the S1Koepe"' sheave, a new technique was-established. This innovation brought with it the certain- advantages which long had been recognised and which are being developed further. For many years, drum winders of many types had been the sole means by which ore had been hauled from mines. This type of winder, with its capacity for rope storage on the drum, permitted mine operating personnel to cut short lengths from

Jan 1, 1964