Search Documents

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

This paper critically reviews the role of institutional research contractors (eg universities and the CSIRO) in the delivery of effective research, development and demonstration outcomes in mineral and coal processing to the Australian mineral industry. The criteria by which such R&D is justified, and the problems of quantifying the benefits of such research, are considered. Third-party funding mechanisms such as NERDDP and AMIRA are reviewed in the context of the difficulty of setting national research priorities. Some case studies are presented which illustrate both the problems and the advantages of institutional research for industry. The transfer of research outcomes to industry is identified as a significant problem which limits the effectiveness of all institutional research. Other topics reviewed include research management, the relationship between industrial companies and their research contractors, and the real costs of research. The paper offers suggestions for the ingredients needed for a successful industry-institution relationship, based on the Australian experience. It is concluded that the Australian model for this relationship is a very effective one, although there is still room for improvement.

Jan 1, 1992

The value of water is defined by its marginal utility. Challenges arise where the marginal utility is difficult to estimate. Therefore, when two or more interested parties wish to access water and they cannot use commensurate units for marginal utility; other means of value comparison must be sought. It is asserted here that sustainability principles can be used to guide this valuation if this is supported by a transparent decision framework. This paper proposes that the ICMM sustainable development principles provide appropriate guidance. In addition, a generic framework for decision making is suggested as a complement. Indicators of water management are recognised widely as an integral part of the accountability of minerals companies towards meeting sustainability goals. Less widely recognised are the ways in which sustainability principles can be used to guide decisions on water management which demonstrate growing awareness of its value. This paper illustrates the use of this logic in water issues associated with global sustainability challenges. It then goes on to demonstrate, using examples, that these links exist at all levels of the minerals industry and that indicators of this type are potentially as powerful as those currently being used. The reason for this is that the path from cause to effect is transparent and direct.

Jan 1, 2006

The Palaeozoic succession of Victoria contains one of the world's major gold provinces with a total production of 2500 tonnes of gold. Larger deposits, including Bendigo (over 800 tonnes Au), are related to Ordovician slates and greywackes, but a wide range of metamorphosed sedimentary and igneous rock types are host to significant gold deposits. Most, if not all, deposits demonstrate structural control, although the controlling structural features are variable between deposits: a majority of deposits comprise quartz veins. It is suggested here that a major factor in making Victoria such a gold-rich province might be a particularly high geothermal gradient in central Victoria during the Tabberabberan orogeny (360-380 my). This generated auriferous metamorphic fluids from underlying successions (?Cambrian) which migrated upwards along active structural pathways. One cause of gold deposition appears to have been fluid reduction by carbon, but other methods are suspected. This model is considerably simpler than the plethora of syngenetic, granite magmatic and lamprophyre-related models that have been proposed recently, but is in basic agreement with Cox et al. (1983). Exploration models for similar gold deposits both within Victoria and elsewhere should take account of the negligible evidence for a major syngenetic contribution to Victorian gold production, and the lack of any clear genetic relationship to particular igneous rock types. A real opportunity exists for new deposit types not identified by the early prospectors.

Jan 1, 1991

The Mobile Miner MM130 (Figure 1) is designed to tunnel or mine in hard rock. It has a 4.1 m diameter cutterhead mounted on a horizontal axis which in turn is perpendicular to the line of the machine. The cutterhead rotates at 15 rpm and is supported on a boom which swings the cutterhead through a horizontal arc.

Jan 1, 1993

By Jones BH

Discovery of the Vera-Nancy deposit in late-1995 followed 12 years of active exploration in and around the Pajingo Epithermal System, an andesite hosted veinfield covering an area of 150 square kilometres at the northern end of the Devono-Carboniferous Drummond Basin in North Queensland. Early exploration targeted open-pittable resources in the numerous auriferous veins and it was not until 1994 that exploration focus shifted to drilling to depths below about 100 metres from surface, which resulted in the Vera-Nancy discovery. That deeper drilling process is still at a very early stage of coverage of the epithermal system as a whole and substantial potential exists for additional discoveries.Drill-out of Vera-Nancy has to-date established a gold resource in excess of 1.4 million ounces. Mine development is proceeding via a twin decline system with first stoped production scheduled for August 1997.

Jan 1, 1997

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

Industrial minerals and rocks (alternat ively called non-metallic minerals) are those- which are economically important because of their desirable physical or chemical properties rather than their metal or energy content. They are divided into nine classes: structural, pig- ments, process aids, ceramics and refractories, chemical source minerals, abrasives, foundry minerals, gem stones, electrical minerals. Development of deposits is influenced by the dominance of marketing,by the required range of products, the-need for specialized process- ing, place value, and the transportation and distribution of high-bulk, low-cost commodities. Evaluation is different from that of base metals because of differences in geological occurrence, sampling methods, testing, treatment, placing a money-value on the material and the importance of export markets.

Jan 1, 1973

By Cook B, Cunningham J

At Mount Isa Mines, a system has been developed for general monitoring of underground mobile equipment. It can provide unit condition monitoring data such as oil pressures and motor temperatures as well as production type information such as unit location and load. The system does not rely on an expensive data communications infrastructure, using instead inexpensive radio base stations which automatically transfer data from mobile units to a surface database server on the company-wide computer network. This paper includes a general overview of the system and a discussion of the practical benefits it is expected to generate.

Jan 1, 1995

Esso Australia Ltd. operates a large natural gas producing system in the Gippsland Basin, supplying gas to the Gas and Fuel Corporation of Victoria, the State Electricity Commission of Victoria and several industrial customers. Gas reaches the Longford processing plants from three offshore platforms via a network of large diameter pipelines, which must be protected against the formation of ice-like hydrates. When gas production commenced in 1969, methanol was used to inhibit hydrate formation in the offshore pipelines. However, later investigations showed that the methanol was causing excessive degradation of molecular sieve in the onshore gas-processing plants. (Molecular sieve is used to remove water and H2S from the gas prior to further processing to remove heavy hydrocarbons.)

Jan 1, 1982

Chief Geologist, Groundwater and Engineering Geology Branch South Australian Department of Mines and Energy The six papers submitted for consideration during this session include two dealing with techniques for measing rock mass behaviour, including permeability, in boreholes, one describing the use of surface geophysical methods to delineate pollution plumes in groundwater together with analytical modelling of the plume, and one presenting a biological tracer technique applied to the determination of the origin of water entering underground mine workings. A paper describing dewatering at a base metal mine in Queensland includes an account of the investigation techniques employed to establish a conceptual model as a basis for the evaluation of various dewatering strategies. Of considerable interest is the use of a field gravity survey to delineate a zone of highly weathered rock which forms the major aquifer at the site.

Jan 1, 1988

Bulk mining and handling technologies have been affected in two ways by the soaring costs of oil products in recent years. Firstly, the substition of oil by coal, oil sands and oil shale demands the development of high-capacity mining and handling equipment, and secondly the rising fuel costs favour a trend away from cost-intensive heavy truck transport. To cope with the growing volumes of material in mining and handling, larger equip- ment units have to be designed. This tendency becomes apparent from the examples of the Hambach open pit mine in Germany, and the Port Kembla handling plant in Australia. A combination of the flexibility of heavy truck transport and the cost advantages of belt conveyors is achieved by the system of semi-mobile crushing installations described in this paper.

Jan 1, 1981

By M G. Aylmore

Thiosulphate is an attractive alternative reagent to cyanide for processing gold ores. It is relatively cheap and non-toxic, forms relatively strong gold and silver complexes, and readily leaches gold ores in ammoniacal solutions, catalysed by Cu(II). It is particularly suited to carbonaceous ores where the recovery of gold by cyanide is poor. However research over the past 20 years has identified a number of issues and impediments that must be understood or overcome before an overall process can be demonstrated as practical and economic for typical oxidised gold ores. This paper reviews our current understanding of thiosulphate chemistry and mechanism of gold dissolution, and discusses the stability of thiosulphate and polythionates. It then reviews the results of leaching various gold ores that have been reported in the literature, discusses gold recovery options, and considers environmental and toxicity issues. Some of the issues that require further research include decreasing the oxidation of thiosulphate by Cu(II) or other oxidants, increasing the extraction of gold compared to cyanide, and understanding the variation in gold recovery between ores. More work is also required to minimise the effect of polythionates on gold recovery using resins or alternative absorbents, to improve the elution of copper and gold from resins, and to recycle or minimise the concentration of reagents.

Jan 1, 2002

THERE is available a considerable amount of literature concerning the practice, and, to a smaller extent, the theory of ventilation as it applies to coal mines. Publications considering the subject of ventilation of metal mines from a practical viewpoint are much less numerous, whilst the treatment of the theoretical aspect of the question (except in so far as is common to coal mining) appears to have been almost neglected. This may be due to one of two causes (a) That in many metal mines (especially those which have not attained a great depth), on account of the greater number of connections with the surface, as compared with coal mines, natural ventilation has sufficed.(b) That in metal mines where the foregoing is not the case the solution of the ventilation problem from theoretical considerations has been regarded as involving so many complications that any attempt at the determination of a set of concrete ventilation figures applying to and throughout the mine would be futile. Whilst it is freely admitted that the difficulties inherent in the application of theory to the ventilation of metal mines are numerous, it must also be admitted that few attempts have been made to overcome them. The ultimate aim, of course, would be the collection of sufficient data to enable the probable behaviour of the air-currents throughout the whole of the workings of any mine to be accurately predicted under any particular set of circumstances. Failing the attainment of this goal of perfection, it would at least appear that much valuable information might be obtained. In ventilation, as in...

Jan 1, 1921

An experienced drill operator is able to make a log of a drill hole defining physical properties of the earth such as hardness or structure as they vary with depth. This log is based on intuition or how the drill æfeelsÆ. Rock characterisation using measure while drilling (MWD) parameters aims at refining this intuition into a package that accurately defines the properties of the subsurface as the drill bit propagates. Subsurface investigation using MWD parameters aims to combine physical drill parameters: Pull down force, rotary speed, penetration rate, torque and vibration in such a way to yield real time rock properties. MWD is investigation in its most primitive form, put simply MWD is merely a physical probe æfeelingÆ what the rock mass is at depth.

Jan 1, 2001

By Cox N

Fragmentation control is perhaps the most critical aspect of quarrying operations, potentially impacting on the costs of all down stream processes, and sometimes even on the economic viability of an operation. The focal points of studies to control fragmentation are generally the pattern of blastholes, the accuracy of drilling, and the most appropriate powder factor. Recent studies suggest that the performance, and consistency of performance, of explosive detonation in the blastholes may also be a significant factor impacting on blast performance in hard rock quarries. This paper presents the results of studies of bulk emulsion and watergel explosive performance, using blasthole velocity of detonation measurements, and its impact on fragmentation. Field studies show a strong correlation between blasthole VoD and blast fragmentation. Another aspect of explosive performance impacting on ease of excavation of blasted rock is muckpile displacement, from which estimates of effective heave energy have been made for different bulk slurry (emulsion and watergel) products.

Jan 1, 1995

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By Fitzpatrick JM

The feed preparation section of the Whyalla iron ore pellet plant includes a screening and crushing plant followed by dry grinding mills. Improvements in the efficiency of the vibrating screen and cone crusher have enabled screening plant throughput to be increased and product size to be decreased. This, in turn, has enabled improvements in the grinding mills' operation.

Jan 1, 1978

By Muchi I

To clarify the characteristics of non-uniform flow of gas through layered burdens of ore and coke, flow equations of continuity and motion were solved numerically taking account of the geometrical effect of a bed. The results are compared with that predicted by an approximate solution. A mathematical-kinetic model for determining the distributions of process variables over the region from the top to the melting level of blast furnace with the horizontal or the inclined layers of burdens is developed in consideration of the uneven gas flow. By the use of this model, the longitudinal and the radial distributions of process variables in an existing blast furnace in Japan were calculated with the aid of a digital computer. Computed results show that the process variables and the melting level change remarkably over the cross-section of the furnace and that the patterns of these distributions are similar to the results observed by other investigators.

Jan 1, 1975

By S Dirdjosuwondo, R Plaisance, L Thoma

PT Freeport Indonesia, a subsidiary of New Orleans-based Freeport McMoran Copper and Gold of New Orleans, operates a large mining complex on the Western half of the Island of New Guinea in Tembagapura, Irian Jaya, Indonesia. The IOZ (Intermediate Ore Zone) mine, one of the underground orebodies, is mined by block caving. The area affected by the cave collects a large quantity of rain and ground waters mixing with fine rock particles. The mixture, commonly called æwet muckÆ, sometimes spills into drawpoints and makes the working environment hazardous to the loader operators. Wet muck is observed in an increasing number of drawpoints in the IOZ mine and remote LHD (Load-Haul-Dump) technology has been implemented to handle the ore. The driving force for this automation project has been the safety of the loader operators. The system has been developed mainly in-house and incorporates state-of-the-art features. Up to eight remote loaders and nine rock breakers are controlled from an underground control room located approximately 400 metres from the active extraction panels. The two underground crushers and nine conveyor feeders are also operated remotely from an adjacent control room. The development of FreeportÆs remote system has taken time and considerable effort. Not only the success of the IOZ mine was at stake but also the fulfillment of environmental commitments pertaining to the mill tailings. Approximately eight per cent of the mill feed must come from underground skarn deposits to neutralise the acid-generating tailings generated by the huge Grasberg open pit ores.

Jan 1, 2000